Certain registers in the AFE IO space require the apll1 clock to be
enabled in order to be read, otherwise the machine hangs (registers like
0x280, 0x410 (AFE_GAIN1_CON0) and 0x830 (AFE_CONN0_5)). During AFE
driver probe, when initializing the regmap for the AFE IO space those
registers are read, resulting in a hang during boot.
This has been observed on the Genio 700 EVK, Genio 510 EVK and
MT8188-Geralt-Ciri Chromebook, all of which are based on the MT8188 SoC.
Assign CLK_TOP_APLL1_D4 as the parent for CLK_TOP_A1SYS_HP, which is
enabled during register read and write, to make sure the apll1 is
enabled during register operations and prevent the MT8188 machines from
hanging during boot.
Cc: stable@vger.kernel.org Fixes: bd568ce198b8 ("arm64: dts: mediatek: mt8188: Add audio support") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20250207-mt8188-afe-fix-hang-disabled-apll1-clk-v2-1-a636d844c272@collabora.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit under Fixes added the 'idle-states' property for SERDES4 lane muxes
without defining the corresponding register offsets and masks for it in the
'mux-reg-masks' property within the 'serdes_ln_ctrl' node.
Fix this.
Fixes: 7287d423f138 ("arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane mux") Cc: stable@vger.kernel.org Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Link: https://lore.kernel.org/r/20250228053850.506028-1-s-vadapalli@ti.com Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hotplugged memory can be smaller than the original memory. For example,
on my target:
root@genericarmv8:~# cat /sys/kernel/debug/memblock/memory
0: 0x0000000064005000..0x0000000064023fff 0 NOMAP
1: 0x0000000064400000..0x00000000647fffff 0 NOMAP
2: 0x0000000068000000..0x000000006fffffff 0 DRV_MNG
3: 0x0000000088800000..0x0000000094ffefff 0 NONE
4: 0x0000000094fff000..0x0000000094ffffff 0 NOMAP
max_pfn will affect read_page_owner. Therefore, it should first compare and
then select the larger value for max_pfn.
As per the Orin Nano Dev Kit schematic, GPIO_G.02 is not available
on this device family. It should not be used at all on Orin NX/Nano.
Having this unused pin mapped as the suspend key can lead to
unpredictable behavior for low power modes.
Orin NX/Nano uses GPIO_EE.04 as both a "power" button and a "suspend"
button. However, we cannot have two gpio-keys mapped to the same
GPIO. Therefore remove the "suspend" key.
The source register is not used for SET* and reading it can result in
a UBSAN out-of-bounds array access error, specifically when the MOPS
exception is taken from a SET* sequence with XZR (reg 31) as the
source. Architecturally this is the only case where a src/dst/size
field in the ESR can be reported as 31.
Prior to 2de451a329cf662b the code in do_el0_mops() was benign as the
use of pt_regs_read_reg() prevented the out-of-bounds access.
In r852_ready(), the dev get from r852_get_dev() need to be checked.
An unstable device should not be ready. A proper implementation can
be found in r852_read_byte(). Add a status check and return 0 when it is
unstable.
In INFTL_findwriteunit(), the return value of inftl_read_oob()
need to be checked. A proper implementation can be
found in INFTL_deleteblock(). The status will be set as
SECTOR_IGNORE to break from the while-loop correctly
if the inftl_read_oob() fails.
Fixes: 8593fbc68b0d ("[MTD] Rework the out of band handling completely") Cc: stable@vger.kernel.org # v2.6+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, during a debugging session using local MPTCP connections, I
noticed MPJoinAckHMacFailure was not zero on the server side. The
counter was in fact incremented when the PM rejected new subflows,
because the 'subflow' limit was reached.
The fix is easy, simply dissociating the two cases: only the HMAC
validation check should increase MPTCP_MIB_JOINACKMAC counter.
Fixes: 4cf8b7e48a09 ("subflow: introduce and use mptcp_can_accept_new_subflow()") Cc: stable@vger.kernel.org Reviewed-by: Geliang Tang <geliang@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250407-net-mptcp-hmac-failure-mib-v1-1-3c9ecd0a3a50@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the debug log, the same req received two SYN-ACK in a very
short time, very likely because the client retransmits the syn ack due
to multiple reasons.
Even if the packets are transmitted with a relevant time interval, they
can be processed by the server on different CPUs concurrently). The
'subflow_req->msk' ownership is transferred to the subflow the first,
and there will be a risk of a null pointer dereference here.
This patch fixes this issue by moving the 'subflow_req->msk' under the
`own_req == true` conditional.
Note that the !msk check in subflow_hmac_valid() can be dropped, because
the same check already exists under the own_req mpj branch where the
code has been moved to.
Fixes: 9466a1ccebbe ("mptcp: enable JOIN requests even if cookies are in use") Cc: stable@vger.kernel.org Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Gang Yan <yangang@kylinos.cn> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250328-net-mptcp-misc-fixes-6-15-v1-1-34161a482a7f@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The split_sg_phys function was incorrectly setting the offsets of all
scatterlist entries (except the first) to 0. Only the first scatterlist
entry's offset and length needs to be modified to account for the skip.
Setting the rest entries' offsets to 0 could lead to incorrect data
access.
I am using this function in a crypto driver that I'm currently developing
(not yet sent to mailing list). During testing, it was observed that the
output scatterlists (except the first one) contained incorrect garbage
data.
I narrowed this issue down to the call of sg_split(). Upon debugging
inside this function, I found that this resetting of offset is the cause
of the problem, causing the subsequent scatterlists to point to incorrect
memory locations in a page. By removing this code, I am obtaining
expected data in all the split output scatterlists. Thus, this was indeed
causing observable runtime effects!
This patch removes the offending code, ensuring that the page offsets in
the input scatterlist are preserved in the output scatterlist.
Currently, when a lock class is allocated, nr_unused_locks will be
increased by 1, until it gets used: nr_unused_locks will be decreased by
1 in mark_lock(). However, one scenario is missed: a lock class may be
zapped without even being used once. This could result into a situation
that nr_unused_locks != 0 but no unused lock class is active in the
system, and when `cat /proc/lockdep_stats`, a WARN_ON() will
be triggered in a CONFIG_DEBUG_LOCKDEP=y kernel:
Tegra264 has updated HSP_INT_DIMENSIONING register as follows:
* nSI is now BIT17:BIT21.
* nDB is now BIT12:BIT16.
Currently, we are using a static macro HSP_nINT_MASK to get the values
from HSP_INT_DIMENSIONING register. This results in wrong values for nSI
for HSP instances that supports 16 shared interrupts.
Define dimensioning masks in soc data and use them to parse nSI, nDB,
nAS, nSS & nSM values.
Fixes: 602dbbacc3ef ("mailbox: tegra: add support for Tegra264") Cc: stable@vger.kernel.org Signed-off-by: Kartik Rajput <kkartik@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The off_gpios could be NULL. Add missing check in the kb3930_probe().
This is similar to the issue fixed in commit b1ba8bcb2d1f
("backlight: hx8357: Fix potential NULL pointer dereference").
This was detected by our static analysis tool.
Cc: stable@vger.kernel.org Fixes: ede6b2d1dfc0 ("mfd: ene-kb3930: Add driver for ENE KB3930 Embedded Controller") Suggested-by: Lee Jones <lee@kernel.org> Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com> Link: https://lore.kernel.org/r/20250224233736.1919739-1-chenyuan0y@gmail.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When determining the actual best period by looping through all
possible PWM configs, the resolution currently used is based on
bit shift value which is off-by-one above the possible maximum
PWM value allowed.
So subtract one from the resolution before determining the best
period so that the maximum duty cycle requested by the PWM user
won't result in a value above the maximum allowed by the selected
resolution.
Cc: stable@vger.kernel.org # 6.4 Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM") Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Link: https://lore.kernel.org/r/20250305-leds-qcom-lpg-fix-max-pwm-on-hi-res-v4-3-bfe124a53a9f@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ideally, the requested duty cycle should never translate to a PWM
value higher than the selected resolution (PWM size), but currently the
best matched period is never reported back to the PWM consumer, so the
consumer will still be using the requested period which is higher than
the best matched one. This will result in PWM consumer requesting
duty cycle values higher than the allowed PWM value.
For example, a consumer might request a period of 5ms while the best
(closest) period the PWM hardware will do is 4.26ms. For this best
matched resolution, if the selected resolution is 8-bit wide, when
the consumer asks for a duty cycle of 5ms, the PWM value will be 300,
which is outside of what the resolution allows. This will happen with
all possible resolutions when selected.
Since for these Hi-Res PWMs, the current implementation is capping the PWM
value at a 15-bit resolution, even when lower resolutions are selected,
the value will be wrapped around by the HW internal logic to the selected
resolution.
Fix the issue by capping the PWM value to the maximum value allowed by
the selected resolution.
Cc: stable@vger.kernel.org # 6.4 Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM") Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Link: https://lore.kernel.org/r/20250305-leds-qcom-lpg-fix-max-pwm-on-hi-res-v4-2-bfe124a53a9f@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent optimization change in LLVM [1] aims to transform certain loop
idioms into calls to strlen() or wcslen(). This change transforms the
first while loop in UniStrcat() into a call to wcslen(), breaking the
build when UniStrcat() gets inlined into alloc_path_with_tree_prefix():
ld.lld: error: undefined symbol: wcslen
>>> referenced by nls_ucs2_utils.h:54 (fs/smb/client/../../nls/nls_ucs2_utils.h:54)
>>> vmlinux.o:(alloc_path_with_tree_prefix)
>>> referenced by nls_ucs2_utils.h:54 (fs/smb/client/../../nls/nls_ucs2_utils.h:54)
>>> vmlinux.o:(alloc_path_with_tree_prefix)
Disable this optimization with '-fno-builtin-wcslen', which prevents the
compiler from assuming that wcslen() is available in the kernel's C
library.
[ More to the point - it's not that we couldn't implement wcslen(), it's
that this isn't an optimization at all in the context of the kernel.
Replacing a simple inlined loop with a function call to the same loop
is just stupid and pointless if you don't have long strings and fancy
libraries with vectorization support etc.
For the regular 'strlen()' cases, we want the compiler to do this in
order to handle the trivial case of constant strings. And we do have
optimized versions of 'strlen()' on some architectures. But for
wcslen? Just no. - Linus ]
The .rodata.(cst|str)* sections are often resized during the final
linking and since these sections do not cover actual symbols there is
no need to include them in the modules.builtin.ranges data.
When these sections were included in processing and resizing occurred,
modules were reported with ranges that extended beyond their true end,
causing subsequent symbols (in address order) to be associated with
the wrong module.
Fixes: 5f5e7344322f ("kbuild: generate offset range data for builtin modules") Cc: stable@vger.kernel.org Signed-off-by: Kris Van Hees <kris.van.hees@oracle.com> Reviewed-by: Jack Vogel <jack.vogel@oracle.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Journal emptiness is not determined by sb->s_sequence == 0 but rather by
sb->s_start == 0 (which is set a few lines above). Furthermore 0 is a
valid transaction ID so the check can spuriously trigger. Remove the
invalid WARN_ON.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Link: https://patch.msgid.link/20250206094657.20865-3-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The I3C master driver may receive an IBI from a target device that has not
been probed yet. In such cases, the master calls `i3c_master_queue_ibi()`
to queue an IBI work task, leading to "Unable to handle kernel read from
unreadable memory" and resulting in a kernel panic.
Typical IBI handling flow:
1. The I3C master scans target devices and probes their respective drivers.
2. The target device driver calls `i3c_device_request_ibi()` to enable IBI
and assigns `dev->ibi = ibi`.
3. The I3C master receives an IBI from the target device and calls
`i3c_master_queue_ibi()` to queue the target device driver’s IBI
handler task.
However, since target device events are asynchronous to the I3C probe
sequence, step 3 may occur before step 2, causing `dev->ibi` to be `NULL`,
leading to a kernel panic.
Add a NULL pointer check in `i3c_master_queue_ibi()` to prevent accessing
an uninitialized `dev->ibi`, ensuring stability.
The target can send the MDB byte followed by additional data bytes.
The readl on MRDATAB reads one actual byte, but the readsl advances
the destination pointer by 4 bytes. This causes the subsequent payload
to be copied to wrong position in the destination buffer.
Cc: stable@kernel.org Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver") Signed-off-by: Stanley Chu <yschu@nuvoton.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250318053606.3087121-3-yschu@nuvoton.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time a file in policy, that is already opened for read, is opened
for write, a Time-of-Measure-Time-of-Use (ToMToU) integrity violation
audit message is emitted and a violation record is added to the IMA
measurement list. This occurs even if a ToMToU violation has already
been recorded.
Limit the number of ToMToU integrity violations per file open for read.
Note: The IMA_MAY_EMIT_TOMTOU atomic flag must be set from the reader
side based on policy. This may result in a per file open for read
ToMToU violation.
Since IMA_MUST_MEASURE is only used for violations, rename the atomic
IMA_MUST_MEASURE flag to IMA_MAY_EMIT_TOMTOU.
Cc: stable@vger.kernel.org # applies cleanly up to linux-6.6 Tested-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Tested-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time a file in policy, that is already opened for write, is opened
for read, an open-writers integrity violation audit message is emitted
and a violation record is added to the IMA measurement list. This
occurs even if an open-writers violation has already been recorded.
Limit the number of open-writers integrity violations for an existing
file open for write to one. After the existing file open for write
closes (__fput), subsequent open-writers integrity violations may be
emitted.
Cc: stable@vger.kernel.org # applies cleanly up to linux-6.6 Tested-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Tested-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mounting the same share twice, once with the "linux" mount parameter
(or equivalently "posix") and then once without (or e.g. with "nolinux"),
we were incorrectly reusing the same tree connection for both mounts.
This meant that the first mount of the share on the client, would
cause subsequent mounts of that same share on the same client to
ignore that mount parm ("linux" vs. "nolinux") and incorrectly reuse
the same tcon.
Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
soc_dev_attr->revision could be NULL, thus,
a pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b02
("ice: Fix some null pointer dereference issues in ice_ptp.c").
On an rdma-capable machine, a start/stop/start and then on a stop of
a knfsd server would lead kref underflow warning because svc_rdma_free
would indiscriminately unregister the rdma device but a listening
transport never calls the rdma_rn_register() thus leading to kref
going down to 0 on the 1st stop of the server and on the 2nd stop
it leads to a problem.
Suggested-by: Chuck Lever <chuck.lever@oracle.com> Fixes: c4de97f7c454 ("svcrdma: Handle device removal outside of the CM event handler") Signed-off-by: Olga Kornievskaia <okorniev@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't move forward with tpm_chip_start() inside tpm_try_get_ops(), unless
TPM_CHIP_FLAG_SUSPENDED is not set. tpm_find_get_ops() will return NULL in
such a failure case.
Fixes: 9265fed6db60 ("tpm: Lock TPM chip in tpm_pm_suspend() first") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Cc: stable@vger.kernel.org Cc: Jerry Snitselaar <jsnitsel@redhat.com> Cc: Mike Seo <mikeseohyungjin@gmail.com> Cc: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch noticed that inode_getblk() can return 1 on successful mapping of
a block instead of expected 0 after commit b405c1e58b73 ("udf: refactor
udf_next_aext() to handle error"). This could confuse some of the
callers and lead to strange failures (although the one reported by
Smatch in udf_mkdir() is impossible to trigger in practice). Fix the
return value of inode_getblk().
Link: https://lore.kernel.org/all/cb514af7-bbe0-435b-934f-dd1d7a16d2cd@stanley.mountain Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Fixes: b405c1e58b73 ("udf: refactor udf_next_aext() to handle error") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
create_user_mr() has correct code to count the number of null keys
used to fill in a hole for the memory map. However, fill_indir()
does not follow the same to cap the range up to the 1GB limit
correspondingly. Fill in more null keys for the gaps in between,
so that null keys are correctly populated.
Fixes: 94abbccdf291 ("vdpa/mlx5: Add shared memory registration code") Cc: stable@vger.kernel.org Reported-by: Cong Meng <cong.meng@oracle.com> Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com> Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20250220193732.521462-2-dtatulea@nvidia.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If FI_ATOMIC_DIRTIED is not set, atomic file can encounter corruption
due to a mismatch between old file size and new data.
To resolve this issue, I changed to set FI_ATOMIC_DIRTIED when
FI_DIRTY_INODE is set. This ensures that FI_DIRTY_INODE, which was
previously cleared by the Writeback thread during the commit atomic, is
set and i_size is updated.
Cc: <stable@vger.kernel.org> Fixes: fccaa81de87e ("f2fs: prevent atomic file from being dirtied before commit") Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com> Reviewed-by: Sunmin Jeong <s_min.jeong@samsung.com> Signed-off-by: Yeongjin Gil <youngjin.gil@samsung.com> Reviewed-by: Daeho Jeong <daehojeong@google.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller detected a use-after-free issue in ext4_insert_dentry that was
caused by out-of-bounds access due to incorrect splitting in do_split.
BUG: KASAN: use-after-free in ext4_insert_dentry+0x36a/0x6d0 fs/ext4/namei.c:2109
Write of size 251 at addr ffff888074572f14 by task syz-executor335/5847
The following loop is located right above 'if' statement.
for (i = count-1; i >= 0; i--) {
/* is more than half of this entry in 2nd half of the block? */
if (size + map[i].size/2 > blocksize/2)
break;
size += map[i].size;
move++;
}
'i' in this case could go down to -1, in which case sum of active entries
wouldn't exceed half the block size, but previous behaviour would also do
split in half if sum would exceed at the very last block, which in case of
having too many long name files in a single block could lead to
out-of-bounds access and following use-after-free.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Cc: stable@vger.kernel.org Fixes: 5872331b3d91 ("ext4: fix potential negative array index in do_split()") Signed-off-by: Artem Sadovnikov <a.sadovnikov@ispras.ru> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://patch.msgid.link/20250404082804.2567-3-a.sadovnikov@ispras.ru Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A client driver may use mhi_unprepare_from_transfer() to quiesce
incoming data during the client driver's tear down. The client driver
might also be processing data at the same time, resulting in a call to
mhi_queue_buf() which will invoke mhi_gen_tre(). If mhi_gen_tre() runs
after mhi_unprepare_from_transfer() has torn down the channel, a panic
will occur due to an invalid dereference leading to a page fault.
This occurs because mhi_gen_tre() does not verify the channel state
after locking it. Fix this by having mhi_gen_tre() confirm the channel
state is valid, or return error to avoid accessing deinitialized data.
Fix deadlock in ivpu_ms_cleanup() by preventing runtime resume after
file_priv->ms_lock is acquired.
During a failure in runtime resume, a cold boot is executed, which
calls ivpu_ms_cleanup_all(). This function calls ivpu_ms_cleanup()
that acquires file_priv->ms_lock and causes the deadlock.
Warn if device is suspended only when runtime PM is enabled.
Runtime PM is disabled during reset/recovery and it is not an error
to use ivpu_ipc_send_receive_internal() in such cases.
Fixes: 5eaa49741119 ("accel/ivpu: Prevent recovery invocation during probe and resume") Cc: stable@vger.kernel.org # v6.13+ Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com> Reviewed-by: Lizhi Hou <lizhi.hou@amd.com> Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Link: https://lore.kernel.org/r/20250325114219.3739951-1-maciej.falkowski@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the HP OMEN 16 Laptop xd000xx to enable mute led.
it uses ALC245_FIXUP_HP_MUTE_LED_COEFBIT with a slight modification
setting mute_led_coef.off to 0(it was set to 4 i guess
in that function) which i referred to your previous patch disscusion
https://bugzilla.kernel.org/show_bug.cgi?id=214735 .
i am not sure whether i can modify the current working function so i
added another version calling
ALC245_FIXUP_HP_MUTE_LED_V1_COEFBIT. and both works for me.
In case of attempts to compress playback something, for instance,
when audio routing is not set up correctly, the audio DSP is left in
inconsistent state because we are not doing the correct things in
the error path of q6asm_dai_compr_set_params().
So, when routing is not set up and compress playback is attempted
the following errors are present (simplified log):
q6routing routing: Routing not setup for MultiMedia-1 Session
q6asm-dai dais: Stream reg failed ret:-22
q6asm-dai dais: ASoC error (-22): at snd_soc_component_compr_set_params()
on 17300000.remoteproc:glink-edge:apr:service@7:dais
After setting the correct routing the compress playback will always fail:
q6asm-dai dais: cmd = 0x10db3 returned error = 0x9
q6asm-dai dais: DSP returned error[9]
q6asm-dai dais: q6asm_open_write failed
q6asm-dai dais: ASoC error (-22): at snd_soc_component_compr_set_params()
on 17300000.remoteproc:glink-edge:apr:service@7:dais
0x9 here means "Operation is already processed". The CMD_OPEN here was
sent the second time hence DSP responds that it was already done.
Turns out the CMD_CLOSE should be sent after the q6asm_open_write()
succeeded but something failed after that, for instance, routing
setup.
Fix this by slightly reworking the error path in
q6asm_dai_compr_set_params().
DSP expects the periods to be aligned to fragment sizes, currently
setting up to hw constriants on periods bytes is not going to work
correctly as we can endup with periods sizes aligned to 32 bytes however
not aligned to fragment size.
Update the constriants to use fragment size, and also set at step of
10ms for period size to accommodate DSP requirements of 10ms latency.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support") Cc: stable@vger.kernel.org Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://patch.msgid.link/20250314174800.10142-5-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the existing code, the buffer position is only reset in pointer
callback, which leaves the possiblity of it going over the size of
buffer size and reporting incorrect position to userspace.
Without this patch, its possible to see errors like:
snd-x1e80100 sound: invalid position: pcmC0D0p:0, pos = 12288, buffer size = 12288, period size = 1536
snd-x1e80100 sound: invalid position: pcmC0D0p:0, pos = 12288, buffer size = 12288, period size = 1536
Fixes: 9b4fe0f1cd791 ("ASoC: qdsp6: audioreach: add q6apm-dai support") Cc: stable@vger.kernel.org Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://patch.msgid.link/20250314174800.10142-4-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the existing code, we are only setting up one period at a time, in a
ping-pong buffer style. This triggers lot of underruns in the dsp
leading to jitter noise during audio playback.
Fix this by scheduling all available periods, this will ensure that the dsp
has enough buffer feed and ultimatley fixing the underruns and audio
distortion.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support") Cc: stable@vger.kernel.org Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://patch.msgid.link/20250314174800.10142-2-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When snd_soc_dapm_new_controls() or snd_soc_dapm_add_routes() fails,
wcd937x_soc_codec_probe() returns without releasing 'wcd937x->clsh_info',
which is allocated by wcd_clsh_ctrl_alloc. Add wcd_clsh_ctrl_free()
to prevent potential memory leak.
Fixes: 313e978df7fc ("ASoC: codecs: wcd937x: add audio routing and Kconfig") Cc: stable@vger.kernel.org Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com> Link: https://patch.msgid.link/20250226085050.3584898-1-haoxiang_li2024@163.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This isn't fixing a real issue, but there's also zero point in going
through group and buffer setup, when the buffers are going to be
rejected once attempted to get used.
As the comment states, io_req_post_cqe() should only be used by
multishot requests, i.e. REQ_F_APOLL_MULTISHOT, which bundled sends are
not. Add a flag signifying whether a request wants to post multiple
CQEs. Eventually REQ_F_APOLL_MULTISHOT should imply the new flag, but
that's left out for simplicity.
REQ_F_APOLL_MULTISHOT doesn't guarantee it's executed from the multishot
context, so a multishot accept may get executed inline, fail
io_req_post_cqe(), and ask the core code to kill the request with
-ECANCELED by returning IOU_STOP_MULTISHOT even when a socket has been
accepted and installed.
The cpumask should not be a local variable, since its pointer is saved
to irq_desc and may be accessed from procfs.
To fix it, use the persistent mask cpumask_of(cpu#).
Cc: stable@vger.kernel.org Fixes: 8deec94c6040 ("net: stmmac: set IRQ affinity hint for multi MSI vectors") Signed-off-by: Qingfang Deng <dqfext@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250318032424.112067-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 32566a6f1ae5 ("scsi: lpfc: Remove NLP_RELEASE_RPI flag from nodelist
structure") introduced a regression with SLI-3 adapters (e.g. LPe12000 8Gb)
where a Link Down / Link Up such as caused by disabling an host FC switch
port would result in the devices remaining in the transport-offline state
and multipath reporting them as failed. This problem was not seen with
newer SLI-4 adapters.
The problem was caused by portions of the patch which removed the functions
__lpfc_sli_rpi_release() and lpfc_sli_rpi_release() and all their callers.
This was presumably because with the removal of the NLP_RELEASE_RPI flag
there was no need to free the rpi.
However, __lpfc_sli_rpi_release() and lpfc_sli_rpi_release() which calls it
reset the NLP_UNREG_INP flag. And, lpfc_sli_def_mbox_cmpl() has a path
where __lpfc_sli_rpi_release() was called in a particular case where
NLP_UNREG_INP was not otherwise cleared because of other conditions.
Restoring the else clause of this conditional and simply clearing the
NLP_UNREG_INP flag appears to resolve the problem with SLI-3 adapters. It
should be noted that the code path in question is not specific to SLI-3,
but there are other SLI-4 code paths which may have masked the issue.
Fixes: 32566a6f1ae5 ("scsi: lpfc: Remove NLP_RELEASE_RPI flag from nodelist structure") Cc: stable@vger.kernel.org Tested-by: Marco Patalano <mpatalan@redhat.com> Signed-off-by: Ewan D. Milne <emilne@redhat.com> Link: https://lore.kernel.org/r/20250317163731.356873-1-emilne@redhat.com Reviewed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mt7925 chip is only support a single radio, so the maximum
number of simultaneous should be 0.
Fixes: 86c051f2c418 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it") Cc: stable@vger.kernel.org Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Tested-by: Caleb Jorden <cjorden@gmail.com> Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250305000851.493671-3-sean.wang@kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the p2p device and MLO station are running concurrently, the p2p device
will occupy the wrong link_idx when the MLO secondary link is added.
Fixes: 9e4c3a007f01 ("wifi: mt76: connac: Extend mt76_connac_mcu_uni_add_dev for MLO") Cc: stable@vger.kernel.org Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Tested-by: Caleb Jorden <cjorden@gmail.com> Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250305000851.493671-2-sean.wang@kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the increase in the number of power tables for 6Ghz on CLC,
the variable nr_country is no longer sufficient to represent the
total quantity. Therefore, we have switched to calculating the
length of clc buf to obtain the correct power table.
Cc: stable@vger.kernel.org Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips") Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250116062131.3860198-1-mingyen.hsieh@mediatek.com Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the new_metric and last_hop_metric variables can reach
the MAX_METRIC(0xffffffff) value, an integer overflow may occur
when multiplying them by 10/9. It can lead to incorrect behavior.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: a8d418d9ac25 ("mac80211: mesh: only switch path when new metric is at least 10% better") Cc: stable@vger.kernel.org Signed-off-by: Ilia Gavrilov <Ilia.Gavrilov@infotecs.ru> Link: https://patch.msgid.link/20250212082124.4078236-1-Ilia.Gavrilov@infotecs.ru Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the workaround for erratum
3.3 RGMII timing may be out of spec when transmit delay is enabled
for the 6320 family, which says:
When transmit delay is enabled via Port register 1 bit 14 = 1, duty
cycle may be out of spec. Under very rare conditions this may cause
the attached device receive CRC errors.
Signed-off-by: Marek Behún <kabel@kernel.org> Cc: <stable@vger.kernel.org> # 5.4.x Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250317173250.28780-8-kabel@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure ->nr_integrity_segments is cloned in blk_rq_prep_clone(),
otherwise requests cloned by device-mapper multipath will not have the
proper nr_integrity_segments values set, then BUG() is hit from
sg_alloc_table_chained().
Fixes: b0fd271d5fba ("block: add request clone interface (v2)") Cc: stable@vger.kernel.org Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250310115453.2271109-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding a socket option support in MPTCP, both the get and set parts
are supposed to be implemented.
IP(V6)_FREEBIND and IP(V6)_TRANSPARENT support for the setsockopt part
has been added a while ago, but it looks like the get part got
forgotten. It should have been present as a way to verify a setting has
been set as expected, and not to act differently from TCP or any other
socket types.
Everything was in place to expose it, just the last step was missing.
Only new code is added to cover these specific getsockopt(), that seems
safe.
When adding a socket option support in MPTCP, both the get and set parts
are supposed to be implemented.
IPV6_V6ONLY support for the setsockopt part has been added a while ago,
but it looks like the get part got forgotten. It should have been
present as a way to verify a setting has been set as expected, and not
to act differently from TCP or any other socket types.
Not supporting this getsockopt(IPV6_V6ONLY) blocks some apps which want
to check the default value, before doing extra actions. On Linux, the
default value is 0, but this can be changed with the net.ipv6.bindv6only
sysctl knob. On Windows, it is set to 1 by default. So supporting the
get part, like for all other socket options, is important.
Everything was in place to expose it, just the last step was missing.
Only new code is added to cover this specific getsockopt(), that seems
safe.
Fixes: c9b95a135987 ("mptcp: support IPV6_V6ONLY setsockopt") Cc: stable@vger.kernel.org Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/550 Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250314-net-mptcp-fix-data-stream-corr-sockopt-v1-2-122dbb249db3@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit de70981f295e ("gve: unlink old napi when stopping a queue using
queue API") unlinks the old napi when stopping a queue. But this breaks
QPL mode of the driver which does not use page pool. Fix this by checking
that there's a page pool associated with the ring.
Cc: stable@vger.kernel.org Fixes: de70981f295e ("gve: unlink old napi when stopping a queue using queue API") Reviewed-by: Joshua Washington <joshwash@google.com> Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250317214141.286854-1-hramamurthy@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable tssel_n is used for selecting TINT source and titsel_n for
setting the interrupt type. The variable titsel_n is wrongly used for
enabling the TINT interrupt in rzv2h_tint_set_type(). Fix this issue by
using the correct variable tssel_n.
While at it, move the tien variable assignment near to tssr.
Fixes: 0d7605e75ac2 ("irqchip: Add RZ/V2H(P) Interrupt Control Unit (ICU) driver") Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20250224131253.134199-3-biju.das.jz@bp.renesas.com Closes: https://lore.kernel.org/CAMuHMdU3xJpz-jh=j7t4JreBat2of2ksP_OR3+nKAoZBr4pSxg@mail.gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Wave5 521C variant does not support 10 bit decoding. When 10 bit
decoding support was added for the 515 variant, a section of the code
was removed which returned an error. This removal causes a timeout for
the 521 variant, which was discovered during HEVC 10-bit decoding tests.
Fixes: 143e7ab4d9a0 ("media: chips-media: wave5: support decoding HEVC Main10 profile") Cc: stable@vger.kernel.org Signed-off-by: Jackson.lee <jackson.lee@chipsnmedia.com> Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While seeking, the driver calls the flush command. Before the flush
command is sent to the VPU, the driver should handle the display buffer
flags and should get all decoded information from the VPU if the VCORE
is running.
Fixes: 9707a6254a8a ("media: chips-media: wave5: Add the v4l2 layer") Cc: stable@vger.kernel.org Signed-off-by: Jackson.lee <jackson.lee@chipsnmedia.com> Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of multiple active instances, new interrupts can occur as soon
as the current interrupt is cleared. If the driver reads the
instance_info after clearing the interrupt, then there is no guarantee,
that the instance_info is still valid for the current interrupt.
Read the instance_info register for each interrupt before clearing the
interrupt.
Fixes: ed7276ed2fd0 ("media: chips-media: wave5: Add hrtimer based polling support") Cc: stable@vger.kernel.org Signed-off-by: Jackson.lee <jackson.lee@chipsnmedia.com> Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a decoder instance is created, the W5_CMD_ERR_CONCEAL register
should be initialized to 0. Otherwise, gray color is occasionally
displayed on the screen while decoding.
Fixes: 45d1a2b93277 ("media: chips-media: wave5: Add vpuapi layer") Cc: stable@vger.kernel.org Signed-off-by: Jackson.lee <jackson.lee@chipsnmedia.com> Signed-off-by: Nas Chung <nas.chung@chipsnmedia.com> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the device's runtime PM status and enable runtime PM before
registering the async sub-device. This is needed to avoid the case where
the device is runtime PM resumed while runtime PM has not been enabled
yet.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 1283b3b8f82b ("media: i2c: Add driver for Sony IMX219 sensor") Cc: stable@vger.kernel.org # for >= v6.6 Reviewed-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Idle the device only after the async sub-device has been successfully
registered. In error handling, set the device's runtime PM status to
suspended only if it has been set to active previously in probe.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 8a89dc62f28c ("media: add imx319 camera sensor driver") Cc: stable@vger.kernel.org # for >= v6.12 Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
words_count denotes the number of words in total payload, while data
points to payload of various property within it. When words_count
reaches last word, data can access memory beyond the total payload. This
can lead to OOB access. With this patch, the utility api for handling
individual properties now returns the size of data consumed. Accordingly
remaining bytes are calculated before parsing the payload, thereby
eliminates the OOB access possibilities.
There is a possibility that init_codecs is invoked multiple times during
manipulated payload from video firmware. In such case, if codecs_count
can get incremented to value more than MAX_CODEC_NUM, there can be OOB
access. Reset the count so that it always starts from beginning.
When we obtain a reference to of a platform_device, we need to release
it via put_device.
Found by cocci:
./platform/nuvoton/npcm-video.c:1677:3-9: ERROR: missing put_device; call of_find_device_by_node on line 1667, but without a corresponding object release within this function.
./platform/nuvoton/npcm-video.c:1684:3-9: ERROR: missing put_device; call of_find_device_by_node on line 1667, but without a corresponding object release within this function.
./platform/nuvoton/npcm-video.c:1690:3-9: ERROR: missing put_device; call of_find_device_by_node on line 1667, but without a corresponding object release within this function.
./platform/nuvoton/npcm-video.c:1694:1-7: ERROR: missing put_device; call of_find_device_by_node on line 1667, but without a corresponding object release within this function.
Instead of manually calling put_device, use the __free macros.
Cc: stable@vger.kernel.org Fixes: 46c15a4ff1f4 ("media: nuvoton: Add driver for NPCM video capture and encoding engine") Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lift the xshutdown (enable) GPIO 1 ms after enabling the regulators, as
required by the sensor's power-up sequence.
Fixes: d30bb512da3d ("media: Add a driver for the ov7251 camera sensor") Cc: stable@vger.kernel.org Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: d30bb512da3d ("media: Add a driver for the ov7251 camera sensor") Cc: stable@vger.kernel.org Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In v4l2_detect_gtf(), it seems safer to cast the 32-bit image_width
variable to the 64-bit type u64 before multiplying to avoid
a possible overflow. The resulting object code even seems to
look better, at least on x86_64.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Commit ceddfd4493b3 ("media: i2c: imx219: Support four-lane operation")
added support for device tree to allow configuration of the sensor to
use 4 lanes with a link frequency of 363MHz, and amended the advertised
pixel rate to 280.8MPix/s.
However it didn't change any of the PLL settings, so actually it would
have been running overclocked in the MIPI block, and with the frame
rate and exposure calculations being wrong as the pixel rate was
unchanged.
The pixel rate and link frequency advertised were taken from the "Clock
Setting Example" section of the datasheet. However those are based on an
external clock of 12MHz, and are unachievable with a clock of 24MHz - it
seems PREPLLCLK_VT_DIV and PREPLLCK_OP_DIV can ONLY be set via the
automatic configuration documented in "9-1-2 EXCK_FREQ setting depend on
INCK frequency", not by writing the registers.
The closest we can get with a 24MHz clock is 281.6MPix/s and 364MHz.
Dropping all support for the 363MHz link frequency would cause problems
for existing users, so allow it, but log a warning that the requested
value is being changed to the supported one.
Fixes: ceddfd4493b3 ("media: i2c: imx219: Support four-lane operation") Cc: stable@vger.kernel.org Co-developed-by: Peyton Howe <peyton.howe@bellsouth.net> Signed-off-by: Peyton Howe <peyton.howe@bellsouth.net> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This loop was recently converted to use for_each_of_graph_port() which
automatically does __cleanup__ on the "port" iterator variable. Delete
the calls to of_node_put(port) to avoid a double put bug.
Fixes: 393194cdf11e ("media: xilinx-tpg: use new of_graph functions") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The visl driver supports both frame and slice mode, with and without a
start-code. But, the range and default for these enum controls was not
set, which currently limits the decoder to enums with a value of 0. Fix
this by setting the decoder mode and start code controls for both the
H.264 and HEVC codecs.
Fixes: 0c078e310b6d ("media: visl: add virtual stateless decoder driver") Cc: stable@vger.kernel.org Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7d968b5badfc ("media: hi556: Return -EPROBE_DEFER if no endpoint is
found") moved the v4l2_fwnode_endpoint_alloc_parse() call in
hi556_check_hwcfg() up, but it did not make the error-exit paths between
the old and new call-site use "goto check_hwcfg_error;" to free the bus_cfg
on errors.
Add the missing "goto check_hwcfg_error;" statements to fix a memleak on
early error-exits from hi556_check_hwcfg().
Fixes: 7d968b5badfc ("media: hi556: Return -EPROBE_DEFER if no endpoint is found") Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If streamzap_callback() receives an urb with any non-critical error
status, i.e. any error code other than -ECONNRESET, -ENOENT or -ESHUTDOWN,
it will try to process IR data, ignoring a possible transfer failure.
Make streamzap_callback() process IR data only when urb->status is 0.
Move processing logic to a separate function to make code cleaner and
more similar to the URB completion handlers in other RC drivers.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 19770693c354 ("V4L/DVB: staging/lirc: add lirc_streamzap driver") Cc: stable@vger.kernel.org Signed-off-by: Murad Masimov <m.masimov@mt-integration.ru> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit df1ae2251a50 ("media: ov08x40: Add OF probe support") added support
for a reset GPIO, regulators and a clk provider controlled through new
ov08x40_power_off() and ov08x40_power_on() functions.
But it missed adding a pm ops structure to call these functions on
runtime suspend/resume. Add the missing pm ops and only call
ov08x40_power_off() on remove() when not already runtime-suspended
to avoid unbalanced regulator / clock disable calls.
Fixes: df1ae2251a50 ("media: ov08x40: Add OF probe support") Cc: stable@vger.kernel.org Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent runtime resume/suspend while MS IOCTLs are in progress.
Failed suspend will call ivpu_ms_cleanup() that would try to acquire
file_priv->ms_lock, which is already held by the IOCTLs.
The change to only use interrupts to handle supported status changes
introduced an issue when it is necessary to poll for the status. Rather
than checking for the status after sleeping the code now sleeps after
the check. This means a correct, but slower, status change on the part
of the TPM can be missed, resulting in a spurious timeout error,
especially on a more loaded system. Switch back to sleeping *then*
checking. An up front check of the status has been done at the start of
the function, so this does not cause an additional delay when the status
is already what we're looking for.
Cc: stable@vger.kernel.org # v6.4+ Fixes: e87fcf0dc2b4 ("tpm, tpm_tis: Only handle supported interrupts") Signed-off-by: Jonathan McDowell <noodles@meta.com> Reviewed-by: Michal Suchánek <msuchanek@suse.de> Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed warning on PM resume as shown below caused due to uninitialized
struct nand_operation that checks chip select field :
WARN_ON(op->cs >= nanddev_ntargets(&chip->base)
The fix uses the higher level nand_reset(chip, chipnr); where chipnr = 0, when
doing PM resume operation in compliance with the controller support for single
die nand chip. Switching from nand_reset_op() to nand_reset() implies more
than just setting the cs field op->cs, it also reconfigures the data interface
(ie. the timings). Tested and confirmed the NAND chip is in sync timing wise
with host after the fix.
Fixes: 97d90da8a886 ("mtd: nand: provide several helpers to do common NAND operations") Cc: stable@vger.kernel.org Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2020, there's been an unnoticed change which rightfully attempted to
report probe deferrals upon DMA absence by checking the return value of
dma_request_chan_by_mask(). By doing so, it also reported errors which
were simply ignored otherwise, likely on purpose.
This change actually turned a void return into an error code. Hence, not
only the -EPROBE_DEFER error codes but all error codes got reported to
the callers, now failing to probe in the absence of Rx DMA channel,
despite the fact that DMA seems to not be supported natively by many
implementations.
Looking at the history, this change probably led to: ad2775dc3fc5 ("spi: cadence-quadspi: Disable the DAC for Intel LGM SoC") f724c296f2f2 ("spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA")
In my case, the AM62A LP SK core octo-SPI node from TI does not
advertise any DMA channel, hinting that there is likely no support for
it, but yet when the support for the am654 compatible was added, DMA
seemed to be used, so just discarding its use with the
CQSPI_DISABLE_DAC_MODE quirk for this compatible does not seem the
correct approach.
Let's get change the return condition back to:
- return a probe deferral error if we get one
- ignore the return value otherwise
The "error" log level was however likely too high for something that is
expected to fail, so let's lower it arbitrarily to the info level.
Fixes: 935da5e5100f ("mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting DMA channel") Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://patch.msgid.link/20250305200933.2512925-2-miquel.raynal@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90807748ca3a ("KVM: arm64: Hide SME system registers from
guests") added trap handling for SMIDR_EL1, treating it as UNDEFINED as
KVM does not support SME. This is right for the most part, however KVM
needs to set HCR_EL2.TID1 to _actually_ trap the register.
Unfortunately, this comes with some collateral damage as TID1 forces
REVIDR_EL1 and AIDR_EL1 to trap as well. KVM has long treated these
registers as "invariant" which is an awful term for the following:
- Userspace sees the boot CPU values on all vCPUs
- The guest sees the hardware values of the CPU on which a vCPU is
scheduled
Keep the plates spinning by adding trap handling for the affected
registers and repaint all of the "invariant" crud into terms of
identifying an implementation. Yes, at this point we only need to
set TID1 on SME hardware, but REVIDR_EL1 and AIDR_EL1 are about to
become mutable anyway.
Cc: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Fixes: 90807748ca3a ("KVM: arm64: Hide SME system registers from guests")
[maz: handle traps from 32bit] Co-developed-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20250225005401.679536-2-oliver.upton@linux.dev Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kvm_arch_vcpu_create() fails to share the vCPU page with the
hypervisor, we propagate the error back to the ioctl but leave the
vGIC vCPU data initialised. Note only does this leak the corresponding
memory when the vCPU is destroyed but it can also lead to use-after-free
if the redistributor device handling tries to walk into the vCPU.
Add the missing cleanup to kvm_arch_vcpu_create(), ensuring that the
vGIC vCPU structures are destroyed on error.
Cc: <stable@vger.kernel.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Oliver Upton <oliver.upton@linux.dev> Cc: Quentin Perret <qperret@google.com> Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20250314133409.9123-1-will@kernel.org Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code for detecting CPUs that are vulnerable to Spectre BHB was
based on a hardcoded list of CPU IDs that were known to be affected.
Unfortunately, the list mostly only contained the IDs of standard ARM
cores. The IDs for many cores that are minor variants of the standard
ARM cores (like many Qualcomm Kyro CPUs) weren't listed. This led the
code to assume that those variants were not affected.
Flip the code on its head and instead assume that a core is vulnerable
if it doesn't have CSV2_3 but is unrecognized as being safe. This
involves creating a "Spectre BHB safe" list.
As of right now, the only CPU IDs added to the "Spectre BHB safe" list
are ARM Cortex A35, A53, A55, A510, and A520. This list was created by
looking for cores that weren't listed in ARM's list [1] as per review
feedback on v2 of this patch [2]. Additionally Brahma A53 is added as
per mailing list feedback [3].
NOTE: this patch will not actually _mitigate_ anyone, it will simply
cause them to report themselves as vulnerable. If any cores in the
system are reported as vulnerable but not mitigated then the whole
system will be reported as vulnerable though the system will attempt
to mitigate with the information it has about the known cores.
Fixes: 558c303c9734 ("arm64: Mitigate spectre style branch history side channels") Cc: stable@vger.kernel.org Reviewed-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20250107120555.v4.2.I2040fa004dafe196243f67ebcc647cbedbb516e6@changeid Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm Kryo 400-series Gold cores have a derivative of an ARM Cortex
A76 in them. Since A76 needs Spectre mitigation via looping then the
Kyro 400-series Gold cores also need Spectre mitigation via looping.
Qualcomm has confirmed that the proper "k" value for Kryo 400-series
Gold cores is 24.
Fixes: 558c303c9734 ("arm64: Mitigate spectre style branch history side channels") Cc: stable@vger.kernel.org Cc: Scott Bauer <sbauer@quicinc.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Trilok Soni <quic_tsoni@quicinc.com> Link: https://lore.kernel.org/r/20250107120555.v4.1.Ie4ef54abe02e7eb0eee50f830575719bf23bda48@changeid Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a45f41d754e0 ("KVM: arm64: Add {get,set}_user for
PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}") changed KVM_SET_ONE_REG to update
the mentioned registers in a way matching with the behavior of guest
register writes. This is a breaking change of a UAPI though the new
semantics looks cleaner and VMMs are not prepared for this.
Firecracker, QEMU, and crosvm perform migration by listing registers
with KVM_GET_REG_LIST, getting their values with KVM_GET_ONE_REG and
setting them with KVM_SET_ONE_REG. This algorithm assumes
KVM_SET_ONE_REG restores the values retrieved with KVM_GET_ONE_REG
without any alteration. However, bit operations added by the earlier
commit do not preserve the values retried with KVM_GET_ONE_REG and
potentially break migration.
Remove the bit operations that alter the values retrieved with
KVM_GET_ONE_REG.
Cc: stable@vger.kernel.org Fixes: a45f41d754e0 ("KVM: arm64: Add {get,set}_user for PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Acked-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20250315-pmc-v5-1-ecee87dab216@daynix.com Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface specifies the symnum field as an input and output; the
hypervisor sets it to the next sequential symbol's index. xensyms_next()
incrementing the position explicitly (and xensyms_next_sym()
decrementing it to "rewind") is only correct as long as the sequence of
symbol indexes is non-sparse. Use the hypervisor-supplied value instead
to update the position in xensyms_next(), and use the saved incoming
index in xensyms_next_sym().
projects / thirdparty / kernel / stable.git / log
