Daniel Golle [Mon, 10 Feb 2025 23:18:46 +0000 (23:18 +0000)]
mediatek: apply bootloader work-around for affected ASUS devices
Apply "u-boot-dont-touch-spi-nand" to ASUS RT-AX59U, ASUS TUF-AX4200 as
well as ASUS TUF-AX6000 routers to prevent U-Boot from wiping MTD
child nodes from DT.
Daniel Golle [Thu, 6 Feb 2025 05:17:54 +0000 (05:17 +0000)]
mediatek: add work-around for ASUS bootloader MTD behavior
ASUS makes use of U-Boot's fdt_fixup_mtdparts() function which applies
the partitions defined in U-Boot's mtdparts and mtdids environment
variables to the devicetree passed over to Linux.
The undesired side-effect is that in this way also all additional
properties and child nodes get wiped, preventing NVMEM cells to be
defined for MTD partitions or UBI volumes.
To work-around this issue, add an additional compatible string
'u-boot-dont-touch-spi-nand' which can be used instead of 'spi-nand' in
case the replacement of the MTD partitions by U-Boot should be skipped
alltogether.
In practise this is mostly relevant for SPI-NAND which anyway comes only
with two partitions nowadays: 'Bootloader' and 'UBI_DEV'. Hence this
work-around is applicable for SPI-NAND only. Similar work-arounds for
other MTD devices can be created as well should they actually be needed.
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin image.
More details can be found here: https://support.linksys.com/kb/article/6564-en/
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX4300_1.0.4.215382_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX4300_1.0.4.215382_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Qiyuan Zhang [Thu, 1 Aug 2024 22:24:55 +0000 (18:24 -0400)]
qualcommax: add kernel cmdline replacement hack
Add kernel command line replacement hack to qualcommax. Now we can
find and replace arguments in the kernel command line by setting
bootargs-find-1, bootargs-replace-1, bootargs-exact-match-1
and bootargs-find-2, bootargs-replace-2, bootargs-exact-match-2
under the chosen node in the device tree.
This hack replaces the first occurence of bootargs-find-X with
bootargs-replace-X. When bootargs-exact-match-X is set to "y",
then the replacement happens only if the kernel command line is
identical to bootargs-find-X.
The initial fix was correct. However, a recently introduced bug in
base-files can cause some unexpected byte overwriting in eeprom.
Since it has been fixed, let's accept this patch again.
Shiji Yang [Sat, 8 Feb 2025 07:36:24 +0000 (15:36 +0800)]
base-files: fix offset conversion on caldata_patch_data()
`$(( ))` will convert uninitialized variable to "0". If we want to
use "-n" to check the string length, it's necessary to make sure the
converted variable is not empty.
Fixes: 652a6677d5fa ("base-files: Add new functions for ath11k caldata") Fixes: https://github.com/openwrt/openwrt/issues/17818 Signed-off-by: Shiji Yang <yangshiji66@qq.com> Link: https://github.com/openwrt/openwrt/pull/17892 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 094b6f593fb4943005e13e2f8581e66bb7c2c8cf)
Lech Perczak [Wed, 12 Feb 2025 01:25:53 +0000 (02:25 +0100)]
ath79: mikrotik: fix reference clock of Routerboard 911G
When support for Routerboard 911G was introduced, Routerboad 912UAG
device tree was used as a base, and the common part. This led to use of
40MHz as the reference clock frequency for both [1], while RB911G uses 25MHz
crystal on the board, causing heavy system clock drift.
Split the definition, and set the reference clock frequency for RB911G
back to 25MHz.
[1] a716ac556497 ("ath79: fix reference clock for RouterBoard 912UAG")
Thanks to
https://forum.openwrt.org/t/zyxel-gs1900-10hp-revision-b1-support-openwrt-firmware/131841/32
for putting me on the right track for this problem
Error that is being fixed - running fw_printenv results in:
"Warning: Bad CRC, using default environment"
and not showing boardmodel
Workaround, manually changing /etc/fw_env.config to
"/dev/mtd1 0x0 0x400 0x10000"
Felix Fietkau [Wed, 12 Feb 2025 10:54:59 +0000 (11:54 +0100)]
hostapd: fix sta psk index for dynamic psk auth
Depending on the config / circumstances, the get_psk call can be called
multiple times from differnt places, which can lead to wrong sta->psk_idx
values. The correct call is the one that is also interested in the vlan_id,
so use the vlan_id pointer as indication of when to set sta->psk_idx.
Also fix off-by-one error for secondary PSKs
Fixes: b2a2c286170d ("hostapd: add support for authenticating with multiple PSKs via ubus helper") Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 8118b2dace06de839e1e23f018059995f4af5e11)
John Crispin [Wed, 11 Dec 2024 14:41:21 +0000 (15:41 +0100)]
umdns: update to latest HEAD
93458ac dns: fix response to TYPE_PTR query 68af311 fix unicast response port and timeout a2b4979 service: announce all services in single dns answer 4537734 display announced services in ubus call umdns browse 0b50c29 display more srv attributes in output of ubus browse function
Felix Fietkau [Sun, 26 Jan 2025 20:20:00 +0000 (21:20 +0100)]
unetd: update to Git HEAD (2025-01-26)
322500403615 service: add default group @ to match all nodes 5f7860306200 ubus: rename unetd_ubus_notify to unetd_ubus_network_notify d13752814651 enroll: add PEX sub-protocol to support enrolling new nodes into a network
Robert Marko [Fri, 6 Dec 2024 17:21:20 +0000 (18:21 +0100)]
ucode: update to Git HEAD (2024-12-06)
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()` efeb57806552 types, vm: refactor usage of global variables f9d2faf67de6 vm: reset signals when freeing VM 4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()` c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type` 373df7299c79 nl80211: properly support split_wiphy_dump for single phys 9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens 0a7ff4715cb8 main: pretty-print `-p` output by default 4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking efc4122124cb struct: do not use global variables for caching types
John Crispin [Fri, 1 Nov 2024 08:26:15 +0000 (09:26 +0100)]
ucode: update to latest HEAD
b0b5d93 Merge pull request #234 from IdWV/fs 60e7a88 Merge pull request #232 from sebastianertz/lib-digest 1752779 digest: implement compile time option to exclude less common algorithms c7268a1 ci: include libmd in MacOS CI builds fcb6f70 lib: introduce digest library 1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve ed5ce8f types: resolve upvalue values in arrays and objects a6e0641 vm: resolve upvalues before pushing them onto the stack ef1baab ci: drop OpenWrt tests for now 63e18ea fs: eliminate the usage of global variables b1bd7b5 types: add ucv_resource_create() helper 3408edf Merge pull request #244 from nbd168/nl80211 8af77e7 nl80211: add new attributes for multi-radio support 1423ad7 nl80211: cover extended feature and EHT rate info attributes ee1d6d8 Merge pull request #237 from sebastianertz/math 4b18a9b Merge pull request #213 from jow-/improve-vector-macros 1f022c0 math: removed global variable for thread safety e5fe6b1 treewide: refactor vector usage code 20307ee utils: improve vector utilities aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl 79ccd9c socket: provide local definition of `struct fanout_args` 402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration 07afe96 Merge pull request #240 from jow-/stricter-number-conversion 736d450 types: fix potential use after free on adding keys during iteration 4134e71 vallist: more thoroughly check for trailing garbage after numeric string 9cf53dd Merge pull request #226 from jow-/lexer-improvements 2b2e732 lexer: make api functions public 855854f lexer: emit comment and template statement block tokens 328a50f lexer: improve token position reporting fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread 6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak 94d1211 compiler: properly treat property names after spread expressions 67cd123 fs: fix potential memory leak on i/o errors in .read()
Tim Harvey [Tue, 17 Dec 2024 22:52:48 +0000 (14:52 -0800)]
imx: 6.6: add a patch to work around a PCI init hang on IMX8M{M,P}
The act of attempting link at gen1 then trying to link at higher speeds
causes a hang with the specific PCIe switch used on the Gateworks Venice
boards. Work around this by linking at the highest speed first as is
common with all other PCI controller drivers.
This commit fixes nmbm configuration mismatch error on Xiaomi AX3000t
with Winbond W25N01KVZEIR spi-nand:
'''
[ 0.786783] NMBM configuration mismatch
'''
Root cause:
1. U-Boot W25N01KV spi-nand driver ia compiled with 64B OOB size for the
chip and store this size in the nmbm signature;
2. Linux W25N01KV driver use 96B OOB.
The change doesn't affect AX3000t variants with other spi-nand chips
(ESMT, Foresee) because their Linux drivers use 64B OOB.
This commit adds new "mediatek,bmt-mtd-overridden-oobsize" property. The
property helps avoid "NMBM configuration mismatch" error if mtd "OOB size"
is not equal to the "spare size" which is stored in the nmbm signature.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
(cherry picked from commit 17dc079) Link: https://github.com/openwrt/openwrt/pull/17707 Signed-off-by: Robert Marko <robimarko@gmail.com>
b11bff90f2ad r8169: add support for RTL8125BP rev.b b3593df26ab1 r8169: add support for RTL8125D rev.b b299ea006928 r8169: adjust version numbering for RTL8126 bb18265c3aba r8169: remove support for chip version 11 2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
ipq806x: fix broken WAN on Linksys EAX and Asrock G10
Fix broken WAN on Linksys EAX and Asrock G10 by incrementing the WAN
interface MAC address + 1. This caused conflicting entry in the FDB
table and caused the WAN port to malfunction with the DSA conversion.
Daniel Golle [Sat, 1 Feb 2025 05:03:50 +0000 (05:03 +0000)]
mediatek: mt7622: fix SATA on BPi-R64
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Daniel Golle [Thu, 30 Jan 2025 05:49:43 +0000 (05:49 +0000)]
generic: net: phy: realtek: work-around hang on SerDes setup
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Shiji Yang [Wed, 1 Jan 2025 08:06:10 +0000 (16:06 +0800)]
ramips: pinctrl: allow mux SDXC pins for mt76x8
The mt76x8 SDXC pin register definition is incompatible with the
mtmips generic pinctrl driver structure. This hack allows us to
mux the SDXC IO to different pin groups in device tree.
Uwe Kleine-König [Mon, 27 Jan 2025 15:12:23 +0000 (16:12 +0100)]
dnsmasq: add fix related to DNSSEC verification from upstream
To find the DS record for a given zone the parent zone's nameserver must
be queried and not the nameserver for the zone. Otherwise DNSSEC
verification for unsigned delegations breaks.
Hauke Mehrtens [Mon, 27 Jan 2025 00:09:33 +0000 (01:09 +0100)]
apm821xx: NETGEAR WNDR4700: Fix compat version
The definition for the netgear_wndr4700 had two different
DEVICE_COMPAT_VERSION definitions.
In commit 5815884c3a2 ("apm821xx: migrate to DSA"), an additional
DEVICE_COMPAT_VERSION := 3.0 attribute was added to the device
definition. The old one with version 2.0 stayed and was defined later
overwriting the new one.
Replace the old version 2.0 with the new version 3.0
ramips: restore full switch performance for USW-Flex
Since commit f1c9afd80138 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd80138 for USW-Flex restores full 1 Gbps switching
performance on all ports.
airoha: an7581: replace eMMC support with upstream version
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Eric Fahlgren [Sun, 26 Jan 2025 17:25:13 +0000 (09:25 -0800)]
octeon: ubnt-usg: add board name to supported devices
The on-device board name reported by 'ubus call system board' is not present
in the generated profiles.json. This results in upgrade tools being unable
to match the image with the proper device. Let's add a 'SUPPORTED_DEVICES'
entry for the board name to fix this.
Daniel Golle [Thu, 23 Jan 2025 03:36:10 +0000 (03:36 +0000)]
generic: fix probe issues with RealTek RTL8221B PHYs
Import patch "net: phy: realtek: mark existing MMDs as present"
When using Clause-45 mode to access RealTek RTL8221B 2.5G PHYs some
versions of the PHY fail to report the MMDs present on the PHY.
Mark MMDs PMAPMD, PCS and AN which are always existing according to
the datasheet as present to fix that.
Fixes: #16823, #17183, #17232 Signed-off-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> Tested-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
(cherry picked from commit 730db6b893748517949b1d3a0c0cb8b6c1288040)
Hauke Mehrtens [Fri, 24 Jan 2025 21:56:59 +0000 (22:56 +0100)]
kernel: Make kmod-usb-chipidea select kmod-phy-ath79-usb
The USB PHY on the ar9330 and similar SoCs needs the PHY driver. In
OpenWrt 23.05 it was compiled into the kernel. The kernel 6.6
configuration does not compile it in any more, make the
kmod-usb-chipidea driver select it to add it to the images.
Chukun Pan [Tue, 3 Dec 2024 15:02:15 +0000 (23:02 +0800)]
mediatek: cudy: fixes typo for spi and mtd properties
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Move the nmbm properties outside the partition definition.
Change uppercase to lowercase, add missing read-only flag.
Sergey Ryazanov [Wed, 22 Jan 2025 22:26:53 +0000 (00:26 +0200)]
ipq40xx: fix compatibility with linux-atm tools
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
Sergey Ryazanov [Wed, 22 Jan 2025 22:26:52 +0000 (00:26 +0200)]
kernel: vrx518_tc: fix ADSL/ATM operation
ATM TC layer have some issues which effectively prevent VRX518 from
being used as ADSL modem. Specifically, there one crash during the ATM
layer configuration and wrong PVC ID selection on packet receiving what
breaks RX path. Fix both of the issues. Make subif iface registration
optional to prevent the crash (see more details in the new patch) and
update the hardcoded PVC ID to match the first allocated channel.
Sergey Ryazanov [Wed, 22 Jan 2025 22:26:51 +0000 (00:26 +0200)]
kernel: vrx518_tc: fix RX desc phys to virt mapping
It looks like VRX518 returns phys addr of data buffer in the 'data_ptr'
field of the RX descriptor and an actual data offset within the buffer
in the 'byte_off' field. In order to map the phys address back to
virtual we need the original phys address of the allocated buffer.
In the same driver applies offset to phys address before the mapping,
what leads to WARN_ON triggering in plat_mem_virt() function with
subsequent kernel panic:
WARNING: CPU: 0 PID: 0 at .../sw_plat.c:764 0xbf306cd0 [vrx518_tc@8af9f5d0+0x25000]
...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = aff5701e
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Noticed in ATM mode, when chip always returns byte_off = 4.
In order to fix the issue, pass the phys address to plat_mem_virt() as
is and apply byte_off later for proper DMA syncing and on mapped virtual
address when copying RXed data into the skb.
Run tested with FRITZ!Box 7530 on both ADSL and VDSL (thanks Jan) links.
Florian Maurer [Wed, 22 Jan 2025 18:59:12 +0000 (19:59 +0100)]
mediatek-mt7622: netgear-wax206 fix wifi leds
the wifi leds of the wax206 were not reacting.
This patch enables the green leds to show activity, as the blue ones are very bright.
Also set the label-mac to the gmac0
Sander Vanheule [Fri, 24 Jan 2025 16:07:21 +0000 (17:07 +0100)]
realtek: Fix old compatible for HPE 1920-8G PoE
Supported devices are listed in the metadata as the first part of the
DTS compatible. This normally follows the format "vendor,device".
When updating the device name of the 180W 1920-8G PoE an underscore was
used, instead of a comma, to join the vendor and device name. This will
lead to warnings for users wanting to sysupgrade a device with an older
compatible, as the device's info does not match the one the metadata.
Fixes: 987c96e88927 ("realtek: rename hpe,1920-8g-poe to match hardware") Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 6a7fa68569ac11bb2c2abb14026e8b84acd3a12f)
Ivan Deng [Thu, 16 Jan 2025 08:53:36 +0000 (00:53 -0800)]
qualcommax: add missing WAN LED support to Spectrum SAX1V1K routers
Fixed an issue where both WAN LEDs light up before plugging in the
ethernet cable and no blinking regardless of WAN network activity.
Updated the LED configuration to reflect proper status:
Green indicates 2.5Gb connection speed.
Yellow indicates other connection speed and traffic activity.
This resolves inconsistent WAN LED behavior on Spectrum SAX1V1K routers.
Dim Fish [Fri, 11 Oct 2024 16:25:29 +0000 (19:25 +0300)]
mediatek: add Airoha AN8855 gigabit switch driver
New revisions of Xiaomi AX3000T with 1.0.84+ stock firmware contain new hardware.
This commit add support for Airoha AN8855 gigabit switch driver with 6.6 kernel patches
Based on https://patchwork.kernel.org/project/netdevbpf/cover/20241209134459.27110-1-ansuelsmth@gmail.com/
Lech Perczak [Mon, 20 Jan 2025 23:10:50 +0000 (00:10 +0100)]
ath79: meraki-mr18: fix initramfs build
Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.
Mikhail Zhilkin [Sat, 11 Jan 2025 14:55:17 +0000 (14:55 +0000)]
mediatek: Xiaomi AX3000t: fix soft brick for the rd23 model
This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users: Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.
RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function
RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call
Changes (breaking):
- Remove support for building 802.3bt TLVs (broken).
Fix:
- Fix memory leaks in EDP/FDP decoding when receiving some TLVs twice.
- Do not set interface description continuously.
- Use a different Netlink socket for changes and queries.
Florian Maurer [Thu, 16 Jan 2025 08:29:55 +0000 (09:29 +0100)]
mediatek-filogic: fix wax220 wifi leds
The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before.
This commit changes this to trigger on activity of the respective radio
projects / thirdparty / openwrt.git / log
