Coia Prant [Tue, 11 Mar 2025 03:33:00 +0000 (11:33 +0800)]
ramips: add support for Hongdian H8922 v30
This is an industrial 4G router equipped with OpenWrt 14.07 OEM
customized version
WARNING: The original firmware device tree is common to multiple
boards, and the device tree name is H9350. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Issue:
- No factory partition, eeprom is located
at /lib/firmware/mt7620a.eeprom
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put rootfs into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press Ctrl+C to break auto boot.
5. Use `system 6` command and follow the instruction to set device
and tftp server IP address and input the rootfs file name.
U-boot will then load the rootfs and write it into
the flash.
6. Use `system 1` command and follow the instruction to set device
and tftp server IP address and input the firmware file name.
U-boot will then load the firmware once.
7. Login to LuCI and use LuCI upgrade firmware.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8922-and-flash.html
Coia Prant [Tue, 11 Mar 2025 03:21:33 +0000 (11:21 +0800)]
mac80211: rt2x00: load the eeprom data from devicetree embedded data on Ralink SoCs
It will allow loading eeprom from eeprom-data embedded in device tree.
Ported from mediatek mt76 wireless driver (drivers/net/wireless/mediatek/mt76/eeprom.c)
Tianling Shen [Wed, 26 Feb 2025 13:52:53 +0000 (21:52 +0800)]
mediatek: add support for CMCC A10
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Daniel Golle [Mon, 3 Mar 2025 13:27:15 +0000 (13:27 +0000)]
libpcap: backport support for various DSA tags
Trying to tcpdump DSA conduits results in errors such as
"unsupported DSA tag: mtk".
Backport two commits adding support for various DSA tags to libpcap.
Robert Marko [Thu, 27 Feb 2025 10:05:26 +0000 (11:05 +0100)]
libpcap: add missing PKG_CONFIG_DEPENDS entries
Currently, enabling USB, BT or Netfilter support after initial compilation
will not trigger a rebuild, so add the missing PKG_CONFIG_DEPENDS so
that rebuild gets triggered.
Eric ZHANG [Sun, 2 Mar 2025 07:54:37 +0000 (15:54 +0800)]
dnsmasq: fix handlers for options `filter_rr` and `cache_rr`
According to:
- https://github.com/openwrt/luci/blob/master/modules/luci-mod-network/htdocs/luci-static/resources/view/network/dhcp.js#L700
- https://github.com/openwrt/luci/blob/master/modules/luci-mod-network/htdocs/luci-static/resources/view/network/dhcp.js#L402
These two options should be of type `MultiValue` but here there're used as single value. This results in dnsmasq crashes when either of these options are set with multiple values, which leads to an invalid space-separated value.
As these options are designed to take multiple values, I think it's better to use list format eg. `list filter_rr 'AAAA'`, instead of `option filter_rr 'AAAA,HTTPS'`.
Martin Schiller [Thu, 6 Mar 2025 08:38:12 +0000 (09:38 +0100)]
mediatek: Refresh kernel configuration
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd85 ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Ahmed Naseef [Tue, 28 Jan 2025 07:28:31 +0000 (11:28 +0400)]
kernel: usbnet: Restore usb%d naming for cdc-ethernet devices with local MAC
Prior to commit https://github.com/torvalds/linux/commit/8a7d12d674ac6f2147c18f36d1e15f1a48060edf,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
Matthew Cather [Mon, 3 Mar 2025 21:46:03 +0000 (15:46 -0600)]
hostapd: get reference to object before removal
`ucv_array_set` releases the array's reference to the object being cleared.
If this is the last reference to the object, it will be freed, making our
pointer `val` invalid.
To avoid this, we need to obtain our own reference to the object so we
can safely return `val`.
Matthew Cather [Mon, 3 Mar 2025 20:00:35 +0000 (14:00 -0600)]
hostapd: consistent reference counting for registry
Since `wpa_ucode_registry_add` collects its own reference to the values added, the
two functions `hostapd_ucode_bss_get_uval` and `hostapd_ucode_iface_get_uval` would
sometimes return a referenced object (from `uc_resource_new`) and sometimes return
an unreferenced object (from `wpa_ucode_registry_get`). Now, both functions always
return a referenced object.
This change also indirectly fixes `hostapd_ucode_bss_get_uval`, ensuring it now
always returns a referenced object.
Signed-off-by: Matthew Cather <mattbob4@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7729f960933a03c9eebd2b65a695ea57718ccb77)
Matthew Cather [Mon, 3 Mar 2025 19:40:39 +0000 (13:40 -0600)]
hostapd: clean-up references to local variables
Remove extra ucv_get calls when passing a referenced value to an object
without using it further.
Signed-off-by: Matthew Cather <mattbob4@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 22eaf1864731dd29918357b26565dbd9420fd314)
Matthew Cather [Mon, 3 Mar 2025 19:22:11 +0000 (13:22 -0600)]
hostapd: fix ucode memory leak with strings
This fixes a common reference counting bug typically along the lines of:
```
uc_value_push(ucv_get(ucv_string_new(...)));
```
This would leave our new string with a reference count of 2, one from
the construction of the string, the other from `ucv_get`. This would
prevent the strings from being correctly cleaned up when it goes out
of scope.
Cedric CHEDALEUX [Mon, 17 Feb 2025 09:44:36 +0000 (10:44 +0100)]
scripts/feeds: shallow clone submodules
When a feed has submodules, all its submodules are fully cloned whereas
the feed itself is shallowed. Let's be consistent and perform shallow clones
as well for the submodules.
Cedric CHEDALEUX [Mon, 17 Feb 2025 09:41:32 +0000 (10:41 +0100)]
scripts/feeds: shallow clone for specific commit update
When a feed is referenced with a specific commit (i.e. <git_url>^<sha1>),
a full clone was performed and a branch was created from the sha1
and named with the sha1. Other git clones operations are shallowed.
As Git does not support clone at a specific commit, let's first perform
a shallow clone to latest commit, then fetch the relevant commit and
finally checkout it (no more 'pseudo' branch).
It saves bandwith and significantly speeds up the feed update process.
Felix Fietkau [Fri, 28 Feb 2025 15:27:36 +0000 (16:27 +0100)]
unetd: update to Git HEAD (2025-02-28)
75a236be122a service: add missing null pointer check f5341f327539 ubus: add api for generating and validating security tokens 3fab99eab4d5 add udebug support 28d86bd30e97 pex: only respond to update requests when we have network data 8e6f37cc361e pex-msg: ignore no-data responses if version is zero 12e6cf7f63e1 pex: create pex host from update responses edc8fdae463a ubus: show the local addresses in network status
Daniel Golle [Wed, 12 Feb 2025 04:21:22 +0000 (04:21 +0000)]
ethtool: work-around ETHTOOL_GRSSH/ETHTOOL_SRSSH ABI breakage
ethtool since version 6.9 introduced support for getting/setting RSS
input transformation supported in Linux since version 6.8.
The now changed kernel ioctl ABI, however, cannot be detected from
userland, and ethtool since version 6.9 simply assumes that a previously
reserved field is now used to set the input transformation.
Unfortunately the default value RXH_XFRM_NO_CHANGE (0xff) used by ethtool
userland creates an incompatibility with older kernels which cannot be
resolved easily without introducing even more ABI breakage.
Work-around the issue and fix support for --set-rxfh and --set-rxfh-indir
ethtool userland tool commands by making the support for input_xfrm
conditional on compile time, and keep it disabled for Linux 6.6.
Fixes: 8c2dcd1518 ("ethtool: update to 6.10") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 3a7467ffde413677de5465dde78a62dfa8d6774f)
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
John Audia [Wed, 12 Feb 2025 13:56:47 +0000 (08:56 -0500)]
openssl: update to 3.0.16
Changes between 3.0.15 and 3.0.16 [11 Feb 2025]
CVE-2024-13176[1] - Fixed timing side-channel in ECDSA signature
computation.
There is a timing signal of around 300 nanoseconds when the top word of
the inverted ECDSA nonce value is zero. This can happen with significant
probability only for some of the supported elliptic curves. In
particular the NIST P-521 curve is affected. To be able to measure this
leak, the attacker process must either be located in the same physical
computer or must have a very fast network connection with low latency.
CVE-2024-9143[2] - Fixed possible OOB memory access with invalid
low-level GF(2^m) elliptic curve parameters.
Use of the low-level GF(2^m) elliptic curve APIs with untrusted explicit
values for the field polynomial can lead to out-of-bounds memory reads
or writes. Applications working with "exotic" explicit binary (GF(2^m))
curve parameters, that make it possible to represent invalid field
polynomials with a zero constant term, via the above or similar APIs,
may terminate abruptly as a result of reading or writing outside of
array bounds. Remote code execution cannot easily be ruled out.
Rudy Andram [Wed, 12 Feb 2025 19:28:49 +0000 (19:28 +0000)]
wireless-regdb: Update to version 2025.02.20
b43aeb5 wireless-regdb: assert and correct maximum bandwidth within frequency difference 68588bf wireless-regdb: Update regulatory info for Syria (SY) for 2020 0dda57e wireless-regdb: Update regulatory info for Moldova (MD) on 6GHz for 2022 b19ab0b wireless-regdb: Update regulatory info for Azerbaijan (AZ) on 6GHz for 2024 f67f40d wireless-regdb: Update regulatory info for Oman (OM) bd70876 wireless-regdb: Update regulatory rules for Armenia (AM) on 2.4 and 5 GHz 6c7cbcc wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band in ETSI/CEPT f9f6b30 wireless-regdb: Update regulatory rules for Austria (AT) 39b47ea wireless-regdb: Update regulatory info for Cayman Islands (KY) for 2024 3dd7ceb wireless-regdb: allow NO-INDOOR flag in db.txt 4d754a1 wireless-regdb: Update regulatory rules for Iran (IR) on both 2.4 and 5Ghz for 2021 8c8308a wireless-regdb: Update frequency range with NO-INDOOR for Oman (OM) c2f11e2 wireless-regdb: update regulatory database based on preceding changes
The proposed detection method was based on reading the LAUNCH_FREADY core flag.
However, this method only works before the cores are launched.
For this reason, the core number detection method has been changed to a simpler one.
For mt6721s the 17th revision bit is zero, hence we know that it is this chip,
so the number of cores is 1.
Sander Vanheule [Sat, 22 Feb 2025 11:06:10 +0000 (12:06 +0100)]
realtek: add PoE enable line to Netgear GS310TP
By switching to the new RTL8231 driver in commit b7af54d5c18c ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Evan Jobling [Thu, 23 Jan 2025 00:13:35 +0000 (00:13 +0000)]
realtek: HPE 1920-48G-PoE: allow fan speed control
The JG928A has an RTL8231 on the aux mdio bus. Add it to dts to expose
the GPIO pins used to control and monitor the fan speed. To enable speed
control, add the appropriate kernel driver module to DEVICE_PACKAGES.
Of note, this does not control all fans for the unit. The power supply
fans are not controlled.
Sander Vanheule [Tue, 28 Jan 2025 07:14:03 +0000 (08:14 +0100)]
realtek: drop old RTL8231 driver
The old RTL8231 driver integrated the MDIO bus access with the GPIO
control ops, making this driver not very portable to newer platforms.
It depended on the SoC ID instead of the compatible to determine the
MDIO access register, further complicating portability.
A new MFD driver is now available, which offers proper pin config as
well as optional LED support, which can work on any (bitbanged) MDIO
bus. Now that all devices have been migrated, we can drop the old code.
Sander Vanheule [Mon, 27 Jan 2025 21:17:57 +0000 (22:17 +0100)]
realtek: add PoE enable line to Netgear GS110TPP
By switching to the new RTL8231 driver in commit b7af54d5c18c ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Sander Vanheule [Sun, 12 Jan 2025 16:57:33 +0000 (17:57 +0100)]
realtek: switch RTL8231 driver for D-Link DGS-1210
Update the common external GPIO DTSI file for the DGS-1210 devices to
use an MDIO device on the auxilairy MDIO bus, as the original driver was
doing behind the screen.
Switching to the new driver will allow for full pin-control and will no
longer reset pin config set by the bootloader.
Sander Vanheule [Sun, 12 Jan 2025 16:53:34 +0000 (17:53 +0100)]
realtek: Switch DGS-1210-10P DTS to gpio.dtsi
The DTS file for the DGS-1210-10P is slightly different from the other
DGS-1210 devices, in that it didn't specify a gpio-restart node when it
was added. The gpio-restart has been found to work on the DGS-1210-10P
as well, so switch it over to the common definitions.
This converts the last device from the product family to the common
definition for the (external) GPIOs.
Tested-by: Michel Thill <jmthill@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 7c0d1c1eb10a7040af6478742dd053f40b24a467)
Sander Vanheule [Sat, 18 Jan 2025 15:51:59 +0000 (16:51 +0100)]
realtek: Drop unused property on DGS-1210 gpio0
The 'indirect-access-id' property on gpio0 is a remnant from the
original GPIO driver. This property has not been relevant on the SoC's
embedded GPIO controller for a long time, so just drop it.
Sander Vanheule [Sat, 18 Jan 2025 20:40:06 +0000 (21:40 +0100)]
realtek: Simple conversions to RTL8231 MFD driver
Change devices with RTL8231 GPIO expander definition that can easily be
translated to the new RTL8231 binding and carry over any gpio-hogs. This
will let them use the new RTL8231 MFD driver, without any functional
changes.
Sander Vanheule [Wed, 22 Jan 2025 11:25:18 +0000 (12:25 +0100)]
realtek: Split Zyxel GS1900-8 into v1 and v2
Zyxel GS1900-8 v2 devices have been produced more recently than v1
devices. As there are v1 boards with RTL8380M rev. C SoCs, it can likely
safely be assumed that all v2 devices will also have a recent SoC
revision, supporting the hardware auxiliary MDIO controller.
Make the GS1900-8 v1 use an emulated auxiliary MDIO bus, for backward
compatibility with devices containing an RTL8380M rev. A.
Since the devicetrees are otherwise identical, GS1900-8 v1 devices with
an RTL8380M rev. B or C will also be able to use the (more efficient) v2
image. This includes any currently functioning device with OpenWrt, so
include the old compatible as a supported device for the GS1900-8 v2.
Sander Vanheule [Tue, 21 Jan 2025 18:57:22 +0000 (19:57 +0100)]
realtek: rtl838x: Enable MDIO_GPIO driver
The mdio-gpio driver is required to support early revision of RTL8380M
slicon (rev A) where the auxilairy MDIO controller does not function
correctly. Add this driver to the rtl838x kernel so devices with old
SoCs are also able to function correctly.
Sander Vanheule [Wed, 22 Jan 2025 11:16:00 +0000 (12:16 +0100)]
realtek: Move GS1900 external GPIO to new DTSI
In order to be able to define the external GPIO controller on an
emulated MDIO bus, move the controller definition outside of the main
GS1900 include for RTL838x-based devices.
Additionally, a new DTSI is provided defining the RTL8231 on the
emulated MDIO bus.
Sander Vanheule [Tue, 21 Jan 2025 18:40:11 +0000 (19:40 +0100)]
realtek: Add virtual MDIO bus on rtl838x
Some RTL8380M-based devices have been around for a long time and use an
early A revision of the RTL8380M SoC. This revision has an issue with
the auxiliary MDIO controller, causing it to malfunction. This may lead
to device reboots when the controller is used.
Provide a bit-banged MDIO bus, which muxes the auxiliary MDIO pins to
their GPIO function. Although this will result in lower performance,
there should otherwise be no functional differences.
Sander Vanheule [Tue, 21 Jan 2025 18:37:25 +0000 (19:37 +0100)]
realtek: Enable Zyxel GS1900's RTL8231 reset line
As the bootloader is reconfiguring the RTL8231 on these devices anyway,
no pin state can be maintained over warm reboots. This results in for
example the PoE disable pin always being asserted by the bootloader.
Define the GPIO line linked to the RTL8231's reset so the MDIO subsystem
will also reset the expander on boot and ensure the line in the correct
state.
Sander Vanheule [Sat, 18 Jan 2025 12:45:55 +0000 (13:45 +0100)]
realtek: rtl839x: Enable AUX MDIO controller
Enable the driver for the Realtek Otto auxiliary MDIO driver so RTL839x
devices can use it. The related node is added to the base devicetree for
rtl839x-based devices, so they can enabled and use it when required.
Sander Vanheule [Sat, 18 Jan 2025 12:28:44 +0000 (13:28 +0100)]
realtek: Update aux-mdio driver
For RTL839x, the driver was producing frequent timeouts on bus accesses.
Increasing the timeout to the one from a recent Realtek SDK resolves
these timeouts. To minimize overhead on different SoCs, each controller
can specify their own timeout.
This also add support for the register format as used on RTL93xx.
Support is added for the RTL930x "ext gpio" controller.
Sander Vanheule [Thu, 16 Jan 2025 12:23:54 +0000 (13:23 +0100)]
realtek: Use atomic poll for aux-mdio commands
regmap_read_poll_timeout() relies on usleep_range() to time the polling
loop. With the current, rather large, scheduling interval, a short
usleep_range() may take a lot longer than expected, causing performance
issues.
Switch the driver over to using regmap_read_poll_timeout_atomic(), which
uses udelay() to time the polling loop.
For comparision, the 'ethtool -m <dev>' command is about 10 times faster
with the atomic variant.
Using 'perf -r10 ethtool -m lan25':
- Driver using regmap_read_poll_timeout():
2.0117 +- 0.0118 seconds time elapsed ( +- 0.58% )
- Driver using regmap_read_poll_timeout_atomic():
0.1674 +- 0.0250 seconds time elapsed ( +- 14.95% )
Fabian Groffen [Wed, 15 Jan 2025 19:12:02 +0000 (20:12 +0100)]
realtek: HPE 1920 24G PoE+ 180W/370W move fans to hwmon
Apply the equivalent of commit f64541db020e ("realtek: HPE 1920 8G PoE+
180W move fans to hwmon") to the 24-ports variants of the HPE 1920 PoE+
switches, with model numbers JG925A and JG926A.
Copy from the original commit message:
Move to using hwmon and gpio-fan. This is by adding gpio_fan_array to
DTS and kmod-hwmon-gpiofan to DEVICE_PACKAGES.
In combination with the new rtl8231 gpio driver the default fan
behaviour will be maximum fan speed.
Bump compat value to 1.1 due to existing config in /etc/config/system
via gpio_switch. Also notify in device compat that fan is now going to
be at bootloader setting (maximum in this case) by default unless turned
down.
As the init script 03_gpio_switches does not perform any action after
removing these devices from it, the file can be dropped.
Sander Vanheule [Tue, 7 Jan 2025 13:59:20 +0000 (14:59 +0100)]
realtek: switch RTL8231 driver for HPE 1920-16/24G
Update the base DTS file for the 16 and 24 port HPE 1920 devices
(JG923A, JG924A, JG925A, JG926A), causing the new RTL8231 MFD driver to
be loaded at start-up.
Evan Jobling [Tue, 14 Jan 2025 12:13:21 +0000 (12:13 +0000)]
realtek: HPE 1920 8G PoE+ 180W move fans to hwmon
The GPIO numbering has changed and is not stable. As a result fan
control via gpio_switch is broken, resulting in errors:
"export_store: invalid GPIO 456"
Move to using hwmon and gpio-fan. This is by adding gpio_fan_array to
DTS and kmod-hwmon-gpiofan to DEVICE_PACKAGES.
In combination with the new rtl8231 gpio driver the default fan
behaviour will be maximum fan speed.
Bump compat value to 1.1 due to existing config in /etc/config/system
via gpio_switch. Also notify in device compat that fan is now going to
be at bootloader setting (maximum in this case) by default unless turned
down.
Sander Vanheule [Thu, 26 Dec 2024 21:26:33 +0000 (22:26 +0100)]
realtek: rtl838x: Switch GS1900 rtl8231 driver
Update the devicetree files to switch the GS1900 devices over to the new
pinctrl and GPIO driver. Enable the drivers to ensure the nodes can be
used.
This may fix issues caused by bad RMW behaviour on the GPIO data lines,
or glitches due to setting the pin direction before the pin level.
Although the driver supports retaining GPIO state after a warm boot,
some bootloaders appear to apply a default configuration on boot, which
may cause an interrupt in PoE-PSE support.
Sander Vanheule [Thu, 26 Dec 2024 19:55:16 +0000 (20:55 +0100)]
realtek: Add pinctrl support for RTL8231
Add pending patches to add RTL8231 support as a MDIO-bus attached
multi-functional device. This includes subdrivers for the pincontrol and
GPIO features, as well as the LED matrix support.
Leave the drivers disabled until required by a device.
Sander Vanheule [Fri, 27 Dec 2024 14:56:44 +0000 (15:56 +0100)]
realtek: rtl838x: Instantiate auxiliary MDIO bus
Add a disabled node for the auxiliary MDIO bus, used to manage the
RTL8231 expanders. A simple-mfd parent node is added, at the same
(implied) address as the switch@1b000000 node, as the switch drivers
should anyway transistion to MFD subdivices at some point.
Additionally, two pinctrl-single node are added to allow the MDX pins to
be muxed correctly, in case the bootloader leaves these unconfigured.
Sander Vanheule [Fri, 27 Dec 2024 14:53:23 +0000 (15:53 +0100)]
realtek: Add driver for auxiliary MDIO busses
Add a driver that exposes the auxiliary busses, used for the RTL8231
expanders, as a proper MDIO controller. The device must be instantiated
under an MFD device, so the driver should also be compatible with SoC
managed by an external CPU via SPI.
Leave the driver disabled in builds until required.
Daniel Golle [Mon, 10 Feb 2025 23:18:46 +0000 (23:18 +0000)]
mediatek: apply bootloader work-around for affected ASUS devices
Apply "u-boot-dont-touch-spi-nand" to ASUS RT-AX59U, ASUS TUF-AX4200 as
well as ASUS TUF-AX6000 routers to prevent U-Boot from wiping MTD
child nodes from DT.
Daniel Golle [Thu, 6 Feb 2025 05:17:54 +0000 (05:17 +0000)]
mediatek: add work-around for ASUS bootloader MTD behavior
ASUS makes use of U-Boot's fdt_fixup_mtdparts() function which applies
the partitions defined in U-Boot's mtdparts and mtdids environment
variables to the devicetree passed over to Linux.
The undesired side-effect is that in this way also all additional
properties and child nodes get wiped, preventing NVMEM cells to be
defined for MTD partitions or UBI volumes.
To work-around this issue, add an additional compatible string
'u-boot-dont-touch-spi-nand' which can be used instead of 'spi-nand' in
case the replacement of the MTD partitions by U-Boot should be skipped
alltogether.
In practise this is mostly relevant for SPI-NAND which anyway comes only
with two partitions nowadays: 'Bootloader' and 'UBI_DEV'. Hence this
work-around is applicable for SPI-NAND only. Similar work-arounds for
other MTD devices can be created as well should they actually be needed.
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin image.
More details can be found here: https://support.linksys.com/kb/article/6564-en/
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX4300_1.0.4.215382_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX4300_1.0.4.215382_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Qiyuan Zhang [Thu, 1 Aug 2024 22:24:55 +0000 (18:24 -0400)]
qualcommax: add kernel cmdline replacement hack
Add kernel command line replacement hack to qualcommax. Now we can
find and replace arguments in the kernel command line by setting
bootargs-find-1, bootargs-replace-1, bootargs-exact-match-1
and bootargs-find-2, bootargs-replace-2, bootargs-exact-match-2
under the chosen node in the device tree.
This hack replaces the first occurence of bootargs-find-X with
bootargs-replace-X. When bootargs-exact-match-X is set to "y",
then the replacement happens only if the kernel command line is
identical to bootargs-find-X.
The initial fix was correct. However, a recently introduced bug in
base-files can cause some unexpected byte overwriting in eeprom.
Since it has been fixed, let's accept this patch again.
Shiji Yang [Sat, 8 Feb 2025 07:36:24 +0000 (15:36 +0800)]
base-files: fix offset conversion on caldata_patch_data()
`$(( ))` will convert uninitialized variable to "0". If we want to
use "-n" to check the string length, it's necessary to make sure the
converted variable is not empty.
Fixes: 652a6677d5fa ("base-files: Add new functions for ath11k caldata") Fixes: https://github.com/openwrt/openwrt/issues/17818 Signed-off-by: Shiji Yang <yangshiji66@qq.com> Link: https://github.com/openwrt/openwrt/pull/17892 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 094b6f593fb4943005e13e2f8581e66bb7c2c8cf)
Lech Perczak [Wed, 12 Feb 2025 01:25:53 +0000 (02:25 +0100)]
ath79: mikrotik: fix reference clock of Routerboard 911G
When support for Routerboard 911G was introduced, Routerboad 912UAG
device tree was used as a base, and the common part. This led to use of
40MHz as the reference clock frequency for both [1], while RB911G uses 25MHz
crystal on the board, causing heavy system clock drift.
Split the definition, and set the reference clock frequency for RB911G
back to 25MHz.
[1] a716ac556497 ("ath79: fix reference clock for RouterBoard 912UAG")
Thanks to
https://forum.openwrt.org/t/zyxel-gs1900-10hp-revision-b1-support-openwrt-firmware/131841/32
for putting me on the right track for this problem
Error that is being fixed - running fw_printenv results in:
"Warning: Bad CRC, using default environment"
and not showing boardmodel
Workaround, manually changing /etc/fw_env.config to
"/dev/mtd1 0x0 0x400 0x10000"
Felix Fietkau [Wed, 12 Feb 2025 10:54:59 +0000 (11:54 +0100)]
hostapd: fix sta psk index for dynamic psk auth
Depending on the config / circumstances, the get_psk call can be called
multiple times from differnt places, which can lead to wrong sta->psk_idx
values. The correct call is the one that is also interested in the vlan_id,
so use the vlan_id pointer as indication of when to set sta->psk_idx.
Also fix off-by-one error for secondary PSKs
Fixes: b2a2c286170d ("hostapd: add support for authenticating with multiple PSKs via ubus helper") Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 8118b2dace06de839e1e23f018059995f4af5e11)
John Crispin [Wed, 11 Dec 2024 14:41:21 +0000 (15:41 +0100)]
umdns: update to latest HEAD
93458ac dns: fix response to TYPE_PTR query 68af311 fix unicast response port and timeout a2b4979 service: announce all services in single dns answer 4537734 display announced services in ubus call umdns browse 0b50c29 display more srv attributes in output of ubus browse function
Felix Fietkau [Sun, 26 Jan 2025 20:20:00 +0000 (21:20 +0100)]
unetd: update to Git HEAD (2025-01-26)
322500403615 service: add default group @ to match all nodes 5f7860306200 ubus: rename unetd_ubus_notify to unetd_ubus_network_notify d13752814651 enroll: add PEX sub-protocol to support enrolling new nodes into a network
Robert Marko [Fri, 6 Dec 2024 17:21:20 +0000 (18:21 +0100)]
ucode: update to Git HEAD (2024-12-06)
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()` efeb57806552 types, vm: refactor usage of global variables f9d2faf67de6 vm: reset signals when freeing VM 4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()` c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type` 373df7299c79 nl80211: properly support split_wiphy_dump for single phys 9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens 0a7ff4715cb8 main: pretty-print `-p` output by default 4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking efc4122124cb struct: do not use global variables for caching types
John Crispin [Fri, 1 Nov 2024 08:26:15 +0000 (09:26 +0100)]
ucode: update to latest HEAD
b0b5d93 Merge pull request #234 from IdWV/fs 60e7a88 Merge pull request #232 from sebastianertz/lib-digest 1752779 digest: implement compile time option to exclude less common algorithms c7268a1 ci: include libmd in MacOS CI builds fcb6f70 lib: introduce digest library 1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve ed5ce8f types: resolve upvalue values in arrays and objects a6e0641 vm: resolve upvalues before pushing them onto the stack ef1baab ci: drop OpenWrt tests for now 63e18ea fs: eliminate the usage of global variables b1bd7b5 types: add ucv_resource_create() helper 3408edf Merge pull request #244 from nbd168/nl80211 8af77e7 nl80211: add new attributes for multi-radio support 1423ad7 nl80211: cover extended feature and EHT rate info attributes ee1d6d8 Merge pull request #237 from sebastianertz/math 4b18a9b Merge pull request #213 from jow-/improve-vector-macros 1f022c0 math: removed global variable for thread safety e5fe6b1 treewide: refactor vector usage code 20307ee utils: improve vector utilities aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl 79ccd9c socket: provide local definition of `struct fanout_args` 402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration 07afe96 Merge pull request #240 from jow-/stricter-number-conversion 736d450 types: fix potential use after free on adding keys during iteration 4134e71 vallist: more thoroughly check for trailing garbage after numeric string 9cf53dd Merge pull request #226 from jow-/lexer-improvements 2b2e732 lexer: make api functions public 855854f lexer: emit comment and template statement block tokens 328a50f lexer: improve token position reporting fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread 6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak 94d1211 compiler: properly treat property names after spread expressions 67cd123 fs: fix potential memory leak on i/o errors in .read()
projects / thirdparty / openwrt.git / log
