Tim Harvey [Thu, 19 Jun 2025 21:32:11 +0000 (14:32 -0700)]
imx: venice: add dt overlay support
Enable DT overlay support:
- add dt-overlay to board features
- add DEVICE_DTS_OVERLAYS
- update the boot script to resize before applying each overlay
Tim Harvey [Thu, 19 Jun 2025 23:58:11 +0000 (16:58 -0700)]
imx: kernel: backport additional upstream patches
Backport some additional upstream patches to resolves some issues when using
dt overlays on gw72xx-0x and gw73xx-0x:
- 6.13-arm64-dts-imx8mm-venice-gw73xx-remove-compatible-in-overlay-files.patch
- 6.12-arm64-dts-imx8mm-venice-gw72xx-remove-compatible-in-overlay-files.patch
ramips: mt7621: include uboot-envtools in some missed devices
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
Josef Schlehofer [Fri, 13 Jun 2025 14:32:45 +0000 (16:32 +0200)]
perf: disable slang support
libs/slang2 is getting picked up from the packages feed, if the slang2
is compiled first and then if you try to compile perf, it fails
due to unmet dependency.
Fixes:
Package perf is missing dependencies for the following libraries:
libslang.so.2
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Roland Reinl [Sun, 27 Apr 2025 11:43:40 +0000 (13:43 +0200)]
mediatek: Create common DTSI for WR3000H and WR3000S
This change moves common elements of the WR3000H and the WR3000S to mt7981b-cudy-wr3000-nand.dtsi.
This will simplify adding of new similar devices, for exapmle WR3000E.
mediatek: filogic: fix 2.5G phy compatible for WR3000H
Following the initial support of the Cudy WR3000H with PHY C22 for the 2.5G WAN
interface, several improvements fixing issues with RealTek RTL8221B PHYs have
been merged.
Therefore we can now bring the DT in line with other equipment and declare the
2.5G WAN PHY as C45.
The manufacturer Cudy usually releases signed openwrt firmware, to
facilitate the migration from the proprietary version to the official
versions of openwrt. In contact with the manufacturer tells me that only
releases the firmware of the WR3000H if and only if
there is an official version. With this proposal I pretend to have an
initial operative version so that they do their part, and facilitate to
the users the possibility of using openwrt. In the present state, it is
only possible to use this firmware by uploading and installing it with
UART connection.
AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H)
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to
enter the U-Boot shell (The recovery.bin image load process must fail).
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000h.bin"
5. IMPORTANT: Make backup from original firmware. System -> Backup
/Flash Firmware -> Save mtdblock contents. All mtdblock one by one,
keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi).
6. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Warning for BL2 and U-BOOT developers
-------------------------------------
The nand partition layout from vendor is slightly diferent from "standard".
The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31.
The UBI partition start at 0x5c0000 be carefull.
DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition
Layout is start-end (not start size)
- 0x000000000000-0x000007800000 : "nmbm0"
- 0x000000000000-0x000000100000 : "bl2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "factory"
- 0x000000380000-0x0000003c0000 : "bdinfo"
- 0x0000003c0000-0x0000005c0000 : "fip"
- 0x0000005c0000-0x0000045c0000 : "ubi"
ALLWAYS for U-BOOT operations check this
setenv mtdids nmbm0=nmbm0
setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi)
Russell Senior [Wed, 2 Apr 2025 12:47:29 +0000 (05:47 -0700)]
tools/patch: bump version to v2.8
drop upstream patches
$ git log --no-merges --oneline v2.7.6..v2.8 48ceda8 Version 2.8 b3d0c93 Regression in commit abe92e8010ab affecting MariaDB tests 29fced6 Count traditional diff pattern lines correctly b5d2124 patch: fix --no-backup-if-mismatch regression 86ac7e2 Fix dodgy assert with side-effects in insert_cached_dirfd 7d87652 Declare an expected test failure on Haiku. 86baf97 build: update gnulib submodule to latest 1ba2c1b Fix two test failures on Haiku. 1da6bf8 Check for newlines only when creating a file name 30ee610 Gnulib renamed some modules 6dbc381 maint: update bootstrap from gnulib 05ac924 build: update gnulib submodule to latest 95e0092 maint: make update-copyright 5bac274 Set --no-backup-if-mismatch when in --posix mode 910fecf Add missing feature tests to the test suite be8b3c6 Disable release-prep c61485b Fix "make release" to handle alpha releases 499916f Add announce-gen module for "make release" adb1ebc Pacify gcc -fsanitize=address 6bdae94 Fix memory leak when malformed unidiff patch 72a146c Port to clang address sanitizer e2e6820 Refactor argc+argv processing 606c091 Omit needless get_some_switches code ee3cc40 Revert "Remove obsolete require_gnu_diff function" 8cae4fc Remove obsolete require_gnu_diff function 164b529 savebuf can return a null pointer 91c1e4f Spelling fixes a03e1ba Port other reject-format test to non-GNU diff 9ba5eb0 Don’t be fooled by NUL bytes in diff directives 79dd5e7 Don’t be fooled by "\000" in file name 8492a6a Port to quasi-GNU diff f6f2c6f In previous patch, make w_q static 0525681 Pacify -Wunterminated-string-initialization 301411d Spelling fixes 4615206 Remove double semicolon 923e0ef Prefer angle bracket headers 5d17ca0 Update more old copyright notices 5f4edd3 Simplify memory allocation of files to delete 802511c Report patch read errors more immediately a93b50d Port fflush usage to OpenBSD 7.5 55e224b Update old copyright notices 33a7fd8 Fix gl_gcc_warnings typo in ‘configure’ 2313b37 build: update gnulib submodule to latest 37fec39 Remove some dependencies no longer needed cc87173 Update NEWS as per recent changes 7887622 Update POSIX citations 18f4dd6 Use “Gruenbacher” in international contexts 638675c Adjust libs to match recent Gnulib 53400a1 Pacify clang -Wbitwise-conditional-parentheses e8e1bcb Remove “support” for nested critical sections b963510 Simplify critical section code in util fns 85949fb Shrink critical sections 448ff9b Defer signals by hand with sigatomic_t b95a603 output_file_later avoid a malloc+free pair 2663228 Defend against closed stdin/stdout/stderr fc77964 Stop using Gnulib ‘execute’ module 470699c Move defer_signals up f696e4e Make sigs, NUM_SIGS local 4d3a4ab Rename block_signals b3bb925 Trade a bit of space for time in parse_c_string 070d859 Allocate first patchbuf statically f46a90f Use bigger buffer size by default 2e64cfd Preinitialize fatal_act.sa_hander 45de0d9 Prefer EXIT_SUCCESS etc. to literal integers 82c4940 Fix some signal handling races eceea61 Fix --set-utc TZ setting 9c55d3f Improve logic for when rename removes source 61c72f0 Fix signal race when renaming file 705c9bc Simplify traverse_another_path via last_component 77f21a6 Stop using Gnulib dirname module fe8ffd9 Fix implausible overflow when reading symlinks 5e84bda Access checks should use effective, not real 8d4ca49 Don’t assume AT_FDCWD != -1 fe5d4a0 Copy input to output attributes via fd if possible ca4c431 Simplify timestamp epoch checking 0ad4347 Check for ftello failures c49a16d Remove format_linenum 22efdee Fix "with multiple words" line number 5a70a1b Drop Plan B c0d465f Prefer ximemdup0 to xmemdup0 b91aab2 Refactor ifetch API 55c8a5c Do not attempt huge I/Os e0e121e Use outfd when setting file attributes 241e57e Don’t assume Linux-like S_IFREG 0f8c628 Use STDOUT_FILENO etc f2c3676 Fix unlikely glitch with ed diffs cec6407 Use fds to copy attrs in create_backup_copy 6b7b01b Be more careful about (time_t) -1 0433553 X == -1 → X < 0 0a66dee Let set_file_attributes use fds not names 36ff2c9 Port to narrow unsigned uid_t 3951496 Check for output errors more systematically 6429630 Report input error right away 03cb187 Simplify EOF testing cc7cde7 Prefer other types to ‘int’ 4c6650b Detect unlikely integer overflow in size calcs abe92e8 Prefer idx_t, ptrdiff_t to lin 30449e2 Fix compatibility issue with blanks in patches 9228a8c pch_swap return type cleanup c1c438d Fix unlikely int overflow in hunk counts 5d3f41f Use char for char in plan_a fb056f2 Cache cwd_is_root dev, ino 84b5f34 Avoid ‘unsigned’ in safe.c d2e113e Simplify get_sha1 f73718b Avoid casts in patch.c 79eef3e Prefer idx_t in util.c 11588d0 Prefer idx_t in pch.c e16037d Prefer idx_t in patch.c 388926f Prefer idx_t in list.h 3582fdb Prefer idx_t in inp.c 4a47c00 build: update gnulib submodule to latest 4f8c4b8 Don’t limit strip counts etc. to INT_MAX 0a810b6 Fix unlikely integer overflows in patch.c bac3b6d Fix unlikely integer overflows in pch.c 8fb784b Fix unlikely integer overflows in inp.c e10f3ca Promote minmax.h to common.h 57e2165 Avoid some memory allocation by not using ‘const’ eb18b39 Remove unnecessary char * casts in inp.c d60cb72 Pacify gcc -Wunused-parameter when !USE_XATTR 05ef886 Pacify gcc -Wunused-parameter when !USE_XATTR 1f8d192 maint: stop using alloca ba92722 Don’t assume O_RDONLY == 0 0f98e03 Avoid syscall when nested signal block 1235ccc Add signal comment 43ee674 build: update gnulib submodule to latest e381947 Update NEWS, README-prereq 2c2a83b Omit _Noreturn when easy a13c2ea Replace __attribute__ with attribute.h 6eb2d13 Switch from ctype.h to c-ctype.h d1a6847 Simplify warning configuration d6631b3 Prefer ATTRIBUTE_* to _GL_ATTRIBUTE_* bc6899d Pacify gcc -Wno-unused-parameter da25985 Improve ‘git diff’ output if desired 248ef13 Prefer strerror to perror 6cb321a A bit more long-string fixing 47bc09d Prefer nullptr to NULL 7608746 More fixing of printing of very long strings 323da0d Don’t assume string sizes fit in int when printing 53d1014 Avoid fprintf INT_MAX overflow when merging 59681c8 Avoid sprintf INT_MAX overflow 4278b91 Reject output file names containing '\n' 34b45bc Update man page a bit. d18c05d Update copyright notices af828e5 Fix some races involving signals b3a6c95 Don’t attempt to remove files we didn’t create 9abc949 Omit goto in try_safe_open 90e62d5 Pacify clang re obsolete O_CREAT test 2b87c1e Allow nested block/unblock of signals 7aa1c3b Adjust to new Gnulib bootstrap post imports 99c0c0b maint: remove generated file lib/Makefile.am 1c087d6 Rely on Gnulib inttypes module 7214f8d Update main locals more consistently 6785b2c Use struct outfile * in function args 72d7ed0 Refactor temp names into struct abf6fb1 Simplify by using Gnulib sigaction d3816ac Avoid unnecessary freeing in output_files 346d3ac Clean up cleanup ff2317b Port better to GNU/Hurd c2d9792 Don’t say empty backups are unreadable 8c27a03 Spelling fixes d46d729 Change manywarnings usage to be more like coreutils 924698b Pacify clang, which dislikes n + "y" 8939519 Pacify -Wstrict-overflow in pch.c 531cc2b Pacify -Wsuggest-attribute=format in util.c ff13fea Port to non-VLA C compilers 3d5c0d1 Rename vars to pacify gcc -Wshadow 56788ce Stop including stdbool.h c10da77 Recommend 64-bit time_t on 32-bit platforms 1e21767 Remove pch_sha1 39005cf Move skip_spaces 755712d Remove pch_timestamp function 04f0eeb Prefer extern inline to static inline for list.h f06c123 maint: pacify gcc 14 -Wcast-align aab6e7b maint: pacify -Wanalyzer-null-argument d1d32c9 maint: work around GCC bug 109839 7575694 maint: pacify gcc -Wmissing-variable-declarations 8f78b09 maint: pacify gcc -Winline bb841fd maint: port _FORTIFY_SOURCE to Ubuntu 4887683 maint: assume STDC_HEADERS 5b8ecde maint: spruce up our .m4 files a bit 009a424 maint: omit obsolete macro calls 299167f maint: simplify .gitignore 3ec44a4 build: update gnulib submodule to latest 68cb529 build: update gnulib submodule to latest f144b35 build: Enable the 'subdir-objects' Automake option. faafc79 build: update gnulib submodule to latest c835ecc Pass the correct stat to backup files 24f81be maint: modernize README-{hacking,prereq} 7623b2d Fix test for presence of BASH_LINENO[0] 0993940 gnulib: update to latest 78ed9de Add missing-section tests to context-format test case 76e7758 Fix failed assertion 'outstate->after_newline' 15b158d Avoid invalid memory access in context format diffs dce4683 Don't follow symlinks unless --follow-symlinks is given 61d7788 Don't crash when RLIMIT_NOFILE is set to RLIM_INFINITY b7b028a Abort when cleaning up fails a5b442c Skip "ed" test when the ed utility is not installed 2b584ae Improve support for memory leak detection 9c98635 Fix swapping fake lines in pch_swap ff81775 Make the (debug & 2) output more useful 369dccc Don't leak temporary file on failed multi-file ed-style patch 1959988 Don't leak temporary file on failed ed-style patch f322a7e Request 'alloca' module from gnulib. 458ac51 Fix 'ed-style' test failure. 1e9104c Fix check of return value of fwrite(). ae81be0 maint: avoid warnings from GCC8 2a32bf0 Minor cleanups in do_ed_script ff1d3a6 Use gnulib execute module 3fcd042 Invoke ed directly instead of using the shell 123eaff Fix arbitrary command execution in ed-style patches (CVE-2018-1000156) b5a91a0 Allow input files to be missing for ed-style patches f290f48 Fix segfault with mangled rename patch 074e239 Test suite: fix Korn shell incompatibility f6bc5b1 Test suite compatibility fixes 3bbebbb Avoid set_file_attributes sign conversion warnings
Stijn Tintel [Mon, 24 Mar 2025 22:20:32 +0000 (00:20 +0200)]
include/trusted-firmware-a.mk: support LTS releases
TF-A LTS releases have an lts- prefix in their version tag. Introduce a
PKG_LTS variable to support these.
As the non-LTS tarbals do not contain the version prefix in the
directory, we need different PKG_BUILD_DIR for each variant:
➜ tar --list --file dl/trusted-firmware-a-v2.12.tar.gz | head -n1
trusted-firmware-a-2.12/
➜ tar --list --file dl/trusted-firmware-a-lts-v2.12.1.tar.gz | head -n1
trusted-firmware-a-lts-v2.12.1/
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
Robert Marko [Sat, 7 Jun 2025 09:53:48 +0000 (11:53 +0200)]
netifd: update to Git HEAD (2025-05-23)
61ae5732adea iprule: amend ipproto netlink nla_put_u32 to nla_put_u8 d610d68c71b8 device: add support for configuring vrf a1b6386a20a6 device: fix bonding primary port selection e8bbf246ce2e system-linux: fix sysfs name for all_ports_active flag 723c699e84f4 Restore disable_ipv6 sysctl after removing a device from bridge or bond d476e18e8d43 iprule: resolve ipproto by name 7901e66c5f27 netifd: iprule add sport and dport
Antonio Flores [Mon, 21 Apr 2025 14:14:54 +0000 (10:14 -0400)]
rockchip: fix the SD card detection on NanoPi R6C/R6S
This patch backport a fix for the SD card detection on NanoPi R6c/R6S
from upstream commit https://github.com/torvalds/linux/commit/95147bb42bc163866fc103c957820345fefa96cd
Nick Hainke [Fri, 13 Jun 2025 12:32:47 +0000 (14:32 +0200)]
ipq-wifi: add missing dependency on TARGET_ath79
A previous commit backported the ipq-wifi update to fix support for the
TP-Link Archer C6 v2 by adding the device to the package. However, it
missed adding the required TARGET_ath79 dependency, causing the
ipq-tplink_archer-c6-v2 build to fail.
The dependency was previously added in commit 4990ce613b7d ("ipq-wifi:
update to 2024-02-17") when several ath79 devices were introduced.
However, since this backport only fixes support for the Archer C6 v2, it
is not feasible to backport all related changes. Therefore, this commit
adds only the missing dependency to resolve the build issue without
pulling in unrelated updates.
Fixes: 0c43acc349a7 ("ipq-wifi: update to Git HEAD (2025-05-30)") Signed-off-by: Nick Hainke <vincent@systemli.org> Link: https://github.com/openwrt/openwrt/pull/19120 Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Sun, 11 May 2025 13:25:54 +0000 (15:25 +0200)]
ucode: update to Git HEAD (2025-05-11)
567207a9bf16 fs: implement fileno() on directory handles eb1d93235509 fs: support passing directory handle or fd in chdir() 38a2254337f1 build: detect whether toolchain employs default source fortification 6eddfc9dff17 resolv: fix fd leak in send_queries 3d36856b2dc5 uci: fix memory leak on cursor() error aafde95f1ecf uci: add cursor() flags argument d8cebc5a6bfd Revert "WIP: lib: support map() over objects" 2599cf80736b zlib: incorporate latest PR changes 830f316a7e49 socker: let sock.peercred() clear error on success 4cbac141406e types: rename u64_to_constant flag to ext_flag d802fe5da5cd types: add support for resources with embedded data/values 71b4fdc6f60b types: add support for setting resource persistent flag 141f799eba08 uloop: use container_of instead of direct pointer casts 1396f8f2988d uloop: use uc_fn_thisval 9a121fc7440c uloop: drop object_registry 11b804d97086 socket: do not clear last_error in socket.error() d5b3a9dc1091 socket: add strerror() method
Fixes: https://github.com/jow-/ucode/issues/285 Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2a9316fbfb6e123e0d2672a9726dc752c7f6dbdd)
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Georgi Valkov [Mon, 14 Apr 2025 13:07:25 +0000 (16:07 +0300)]
toolchain: gcc: fix build error with Xcode 16.3
Xcode 16.3 defines TARGET_OS_MAC, it was not defined in prior versions.
zutil.h conditionally defines fdopen as NULL when this macro is defined,
resulting in the following build error:
In Xcode 16.2 and earlier, TARGET_OS_MAC was not defined so this entire
block was ignored, gcc and gdb used to compile and work fine.
This may have been used for compatibility with older versions of macOS,
but is no longer needed. By pure luck, the build worked fine for a long
time, because it did not properly detect macOS.
Fixed by removing the check for TARGET_OS_MAC.
Note that since Xcode 16.3, an entire set of TARGET_OS macros
are now defined, most of which are set to 0:
TARGET_OS_LINUX 0
TARGET_OS_MAC 1
TARGET_OS_OSX 1
Georgi Valkov [Mon, 14 Apr 2025 12:28:23 +0000 (15:28 +0300)]
toolchain: gdb: fix build error with Xcode 16.3
Xcode 16.3 defines TARGET_OS_MAC, it was not defined in prior versions.
zutil.h conditionally defines fdopen as NULL when this macro is defined,
resulting in the following build error:
In Xcode 16.2 and earlier, TARGET_OS_MAC was not defined so this entire
block was ignored, gcc and gdb used to compile and work fine.
This may have been used for compatibility with older versions of macOS,
but is no longer needed. By pure luck, the build worked fine for a long
time, because it did not properly detect macOS.
Fixed by removing the check for TARGET_OS_MAC.
Note that since Xcode 16.3, an entire set of TARGET_OS macros
are now defined, most of which are set to 0:
TARGET_OS_LINUX 0
TARGET_OS_MAC 1
TARGET_OS_OSX 1
Eric Fahlgren [Fri, 6 Jun 2025 23:43:27 +0000 (16:43 -0700)]
package: rework contents of package index.json
Rework the generation of the index.json version of the package
indexes to match the original intent (i.e., for use by the ASU
server and other downstream projects). The current file contains
package names that have ABI versioning, making them unusable by ASU,
so we now remove the ABI suffixes.
Also adds a 'version' field to the json, so downstream utilities
can detect the new semantics of the package name fields.
Paul Donald [Wed, 26 Mar 2025 17:43:45 +0000 (18:43 +0100)]
lldpd: enable hardware inventory information (TLV) management
lldpd can send several hardware inventory TLV fields. Extend the init
script to provide these when the existing flag 'lldpmed_no_inventory' is
disabled. Five new methods provide default values for some of them,
taken from /etc/os-release and /etc/board.json.
There is no homogeneous method to determine the hardware serial number,
so it can be provided manually, as can asset ID.
Note: properties >= 32 characters are truncated at send time (by lldpd),
and some (Cisco) equipment displays junk after strings >= 32 characters.
So truncate to 31.
Tested on: 24.10.0 (known compatible with 22 and 23 also)
Since the early beginning of the Realtek DSA driver there is an uncovered
locking issue between the standard (parent) mdio bus and the DSA (child)
mdio bus. This comes from the fact that the DSA bus simply links to the
parent read and write functions and calls them directly. This leads to
the following lock issue.
- Child bus calls phy_read/write functions and uses its internal lock
- Parent bus calls phy_read/write functions and uses its internal lock
It becomes clear that critical section can be accessed twice without
knowing that a operation from the other bus is currently active. This
can lead to critical malfunctions because the mdio driver needs a lot of
internal magic to get page selection done right. Effects are:
- The original page is lost after a phy_write/read_paged() call
- dmesg like "Realtek RTL8218B (external) rtl838x slave mii-0:00:
Expected external RTL8218B, found PHY-ID 6b23"
Other DSA drivers simply use the read/write functions from the parent bus
and thus avoid locking issues. Do it the same way.
realtek: refactor net rx interrupt handler rtl83xx_net_irq()
Cleanup the code of the RTL83xx packet receive interrupt handler. Not
only for better readability but to avoid inconsistencies and stalls on
the RTL839x targets.
The current implementation seems to come from the GPL source code.
Calling the existing cleanup() function inside the interrupt context
without any locks conflicts with SMP & NAPI polling and makes things
worse instead of giving any benefit. Simply ignore RX buffer overruns
and let the device handle packet dropping itself.
The RTL8214FC currently uses generic PHY functions. That makes it look like a copper
device. Switching to/from fibre works fortunately but the autonegotiation handling
still works on MII_LPA (PHY register 5) as if a copper link is used. Fix that by
- advertising a superset of TP/FIBRE features
- using clause 37 functions when on fibre
Additionally enhance the code of the driver to assist further development.
- log the speed of the inserted module to detect wrongly inserted 10gbase-r modules
- order phy driver functions alphabetically (keep match/name on top)
- remove genphy_loopback as the kernel uses it if not provided
Remark! The driver internally uses PORT_MII for the TP port. Align with that and
report MII to ethtool instead of TP. Other drivers do the same and it can be
changed in the future if needed.
The Arcadyan WE410443 is a WiFi AC access point distributed by various ISPs
under various names, including KPN SuperWifi and BT Whole Home Wi-Fi. It
features one ethernet port, dual MT7615N radios and four internal antennas.
Installation:
The bootloader is locked with a password, so the image needs to be written
directly to the SPI flash chip. To do this, you need to open up the case,
remove the heatsink and connect the flash chip to a Raspberry Pi. Use the
following connections:
You can solder wires to the flash chip, or use a SOIC16 clip. More details on
the Raspberry Pi and SPI chip pinouts are available on the wiki [1]
When you have the Raspberry Pi connected to the flash chip, boot your Pi and
follow the instructions:
1) Make sure your Pi has SPI enabled with sudo raspi-config
Antti Seppälä [Sat, 10 May 2025 10:54:56 +0000 (13:54 +0300)]
qmi: increase SIM power-cycle timeouts
Some modems and SIM cards take a bit longer to initialize after UIM has been
powered off. Waiting too little time can cause the qmi protocol to end up
in a loop repeatedly power-cycling the SIM card.
Avoid that by
a) increasing the time we unconditionally sleep after --uim-power-on
b) increasing the time we allow uqmi to wait for response for --uim-get-sim-state
Tianling Shen [Mon, 26 May 2025 06:54:08 +0000 (14:54 +0800)]
rockchip: add missing symbol
Commit 7cace002baaf added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
rockchip target.
David Bauer [Mon, 13 Jan 2025 14:18:31 +0000 (15:18 +0100)]
ipq40xx: use correct wired MAC-addresses for RUTX50
The Teltonika RUTX50 mac-addresses on its wired interfaces are currently
random on every boot.
Setting the mac-addresses from device-tree using nvmem does not work, as
the vendor bootloader mangles the mtd partitions, removing the
nvmem-cells property.
To remedy the random mac-addresse, set the correct ones in preinit.
Nick Hainke [Sun, 4 May 2025 20:38:10 +0000 (22:38 +0200)]
tools/b43-tools: update to latest version, fix C23 build
Update b43-tools to the latest upstream version to fix a
compilation error with C23:
util.h:25:15: error: 'bool' cannot be defined via 'typedef'
25 | typedef _Bool bool;
| ^~~~
Changelog: c6fc53f replace custom bool typedef with <stdbool.h> dadf30c fix format warning in compilation 2fe10ea b43-fwdump: Fix forwarding of arguments to disassembler
Benjamin Berg [Wed, 30 Apr 2025 19:15:18 +0000 (21:15 +0200)]
mac80211: add patch to suppress PREP when mesh forwarding is disabled
This fixes a bug where mac80211 would respond to a PREQ frame when a
neighbor table entry exists locally even though it will not forward the
frame and the reported path does not actually work.
Robert Marko [Sat, 24 May 2025 10:20:54 +0000 (12:20 +0200)]
image: only filter out images when ImageBuilder is used
Currently, we are filtering out images if DEFAULT:=n or BROKEN:=y are set,
so if you are building from scratch and want to build custom images that
are stripped down to fit, you must edit the image recipe or its just
filtered out.
So, to allow this behaviour when building from scratch as we can assume
that person doing that knows what they are attempting to do lets just limit
the filtering to ImageBuilder.
Fixes: f060615a78e5 ("image: respect DEFAULT and BROKEN when Default profile is selected") Signed-off-by: Robert Marko <robimarko@gmail.com>
Import pending PXA I2C recovery fixes so that if I2C recovery is enabled in
the DTS it does not completely break I2C as it currently does since kernel
6.6.
Stijn Tintel [Thu, 1 May 2025 22:46:25 +0000 (01:46 +0300)]
realtek: add missing symbol
Commit d7e82c78d7a2 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7a2 ("generic: backport Realtek PHY patches from upstream") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ab8708767299c2aebe6a2c1f62abf246214d0d1c)
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Robert Marko [Fri, 16 May 2025 11:18:46 +0000 (13:18 +0200)]
image: respect DEFAULT and BROKEN when Default profile is selected
Currently, when you select the Default profile it does not honor DEFAULT:=n
nor BROKEN:=y in device profiles but rather just tries to build all of them.
This may work when building directly, but when using Image Builder it will
always fail since no kernel or anything else is present for devices that
have DEFAULT:=n or BROKEN:=Y set since those are skipped during build.
So, lets look for DEFAULT being set to "n" or BROKEN being set to "y" and
then remove clear _PROFILE_SET so they dont end up being marked for
installation.
Henry Tung [Sun, 4 May 2025 18:29:54 +0000 (11:29 -0700)]
mac80211: ath11k: fix broadcast failures during GTK rekeying
Revert key_cipher change to NONE when clearing key.
Setting to NONE triggers asserts in the firmware and causes broadcast
drops with ath11k firmware 2.9.0.1, so until a future blob
fixes this, revert this as a workaround.
Imported from
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/blob/win.wlan_host_opensource.3.0.r24/patches/ath11k/350-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch
David Bauer [Tue, 13 May 2025 23:49:44 +0000 (01:49 +0200)]
ramips: pad EX400 kernel partition to retain web recovery
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
David Bauer [Sun, 4 May 2025 02:45:03 +0000 (04:45 +0200)]
ramips: support Genexis EX400 touch controller
Add the necessary package dependencies as well as device-tree properties
to support the touch-inputs as well as missing LEDs on the Genexis Pulse
EX400 range extender.
David Bauer [Sun, 4 May 2025 02:47:32 +0000 (04:47 +0200)]
ramips: add Semtech SX9512 touch input driver
This driver is required for the touch-inputs as well as some LEDs on the
Genexis Pulse EX400.
The driver was also sent upstream. As the EX400 is currently the only
consumer, the driver is added target-specific for ramips.
Once the driver has been accepted upstream and is provided in a kernel
release used by OpenWrt, the package should be moved to the global input
drivers.
Eric Fahlgren [Thu, 8 May 2025 22:28:52 +0000 (15:28 -0700)]
imagebuilder: exclude metadata for profiles that have no kernel
Device profiles that specify 'DEFAULT := n' are being included
in the imagebuilder metadata, specifically in .profiles.mk, even
though there is no kernel built for the device. This results in
'make info' showing the device as valid, but then 'make image
PROFILE=xxx' failing with 'No rule to make target xxx-kernel.bin ...'
We exclude these profiles from the imagebuilder, avoiding these
errors.
projects / thirdparty / openwrt.git / log
