Vincent Siles [Fri, 22 Apr 2016 07:52:06 +0000 (09:52 +0200)]
arm: Fix SCFG ICID reg addresses
On the LS102x boards, in order to initialize the ICID values of
masters, the dev_stream_id array holds absolute offsets from the
base of SCFG.
In ls102xa_config_ssmu_stream_id, the base pointer is cast to
uint32_t * before adding the offset, leading to an invalid address.
Casting it to void * solves the issue.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com> Reviewed-by: York Sun <york.sun@nxp.com>
As the issue about the stack will get corrupted when switching between
the early and final mmu tables is fixed by commit 70e21b064, the
workaround to flush dcache is unnecessary and should be removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Tue, 15 Mar 2016 06:36:43 +0000 (14:36 +0800)]
sf: Disable 4-KB erase command for SPANSION S25FS-S family
The S25FS-S family physical sectors may be configured as a hybrid
combination of eight 4-kB parameter sectors at the top or bottom
of the address space with all but one of the remaining sectors
being uniform size.
The default status of the flash is in this hybrid architecture.
The parameter sectors and the uniform sectors have different erase
commands.
This patch disable the hybrid sector architecture then the flash will
has uniform sector size and uniform erase command.
This configuration is temporary, the flash will revert to hybrid
architecture after power on reset.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Tue, 15 Mar 2016 06:36:42 +0000 (14:36 +0800)]
spi: fsl_qspi: Enable Spansion S25FS-S family flashes
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Tue, 15 Mar 2016 06:36:41 +0000 (14:36 +0800)]
spi: fsl_qspi: Assign AMBA mem according CS num in dts
QSPI controller automatic enable the chipselect signal according the
dest AMBA memory address. Now we distribute the AMBA memory zone
averagely to every chipselect slave device according chipselect
numbers got from dts node.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Tue, 15 Mar 2016 06:36:40 +0000 (14:36 +0800)]
spi: fsl_qspi: Fix issues on arm64
The address value and size value get from dts "reg" property have
type of u64 on arm64. If we assign those values to "u32" variables,
driver can't work correctly. Converting the type of those variables
to fdt_xxx_t.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
Alex Porosanu [Mon, 11 Apr 2016 07:42:50 +0000 (10:42 +0300)]
armv8/fdt: add fixup_crypto_node
For Qoriq PPC&ARM v7 platforms, the crypto node is being fixup'ed in
order to update the SEC internal version (aka SEC ERA). This patch
adds the same functionality to the ARMv8 SoCs.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Shengzhou Liu [Thu, 7 Apr 2016 08:22:21 +0000 (16:22 +0800)]
armv8/ls1043: Add workaround for DDR erratum A-008850
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Simon Glass [Sun, 1 May 2016 19:52:44 +0000 (13:52 -0600)]
dm: mmc: test: Add tests for MMC
Add a simple test which checks that a sandbox-emulated SD card can be used
correctly. This tests plumbing through the MMC stack's block-device
implementaion.
Simon Glass [Sun, 1 May 2016 19:52:42 +0000 (13:52 -0600)]
dm: mmc: sandbox: Add an SD-card emulation
Add an emulation of an SD card to sandbox, allowing MMC to be used in tests.
The emulation is very simple, supporting only card detection and reading
test data.
Simon Glass [Sun, 1 May 2016 19:52:40 +0000 (13:52 -0600)]
dm: mmc: Add a way to bind MMC devices with driver model
Binding an MMC device when CONFIG_BLK is enabled requires that a block
device be bound as a child of the MMC device. Add a function to do this.
The mmc_create() method will be used only when DM_BLK is disabled.
Simon Glass [Sun, 1 May 2016 19:52:39 +0000 (13:52 -0600)]
dm: mmc: Implement the MMC functions for block devices
Implement the functions in mmc_legacy.c for driver-model block devices, so
that MMC can use driver model for these. This allows CONFIG_BLK to be enabled
with DM_MMC.
Simon Glass [Sun, 1 May 2016 19:52:35 +0000 (13:52 -0600)]
dm: mmc: Move the device list into a separate file
At present the MMC subsystem maintains its own list of MMC devices. This
cannot work with driver model, which needs to maintain this itself. Move the
list code into a separate 'legacy' file. The core MMC code remains, and will
be shared with the driver-model implementation.
Simon Glass [Sun, 1 May 2016 19:52:30 +0000 (13:52 -0600)]
dm: blk: Add functions to select a hardware partition
The block device uclass does not currently support selecting a particular
hardware partition but this is needed for MMC. Add it so that the blk API
can support MMC properly.
Simon Glass [Sun, 1 May 2016 19:52:27 +0000 (13:52 -0600)]
dm: mmc: Add a function to obtain the block device
The MMC block device is contained within struct mmc. But with driver model
this will not be the case. Add a function to obtain the block device. We
can later implement this for CONFIG_BLK.
Simon Glass [Sun, 1 May 2016 19:52:25 +0000 (13:52 -0600)]
dm: mmc: Move mmc_switch_part() above its callers
This function is defined after it is used. In preparation for making it
static, move it up a little. Also drop the printf() which should not appear
in a driver.
Simon Glass [Sun, 1 May 2016 17:36:29 +0000 (11:36 -0600)]
dm: blk: Add a easier way to create a named block device
Add a function that automatically builds the device name given the parent
and a supplied string. Most callers will want to do this, so putting this
functionality in one place makes more sense.
Simon Glass [Sun, 1 May 2016 17:36:28 +0000 (11:36 -0600)]
dm: blk: Allow blk_create_device() to allocate the device number
Allow a devnum parameter of -1 to indicate that the device number should be
alocated automatically. The next highest available device number for that
interface type is used.
Simon Glass [Sun, 1 May 2016 17:36:26 +0000 (11:36 -0600)]
dm: sata: Add support for driver-model block devices
Add driver-model block-device support to the SATA implementation. This is
just a dummy implementation for now, since the SATA low-level API uses
numbered devices and that doesn't fit with driver model.
Simon Glass [Sun, 1 May 2016 17:36:11 +0000 (11:36 -0600)]
dm: sata: Separate the non-command code into its own file
At present the SATA command code includes both the command-processing code
and the core SATA functions and data structures.
Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly.
With this commit:
- All CONFIG option are referenced from the non-command code
- The concept of a 'current SATA device' is confined to the command code
This will make it easier to convert this code to driver model.
Simon Glass [Sun, 1 May 2016 17:36:10 +0000 (11:36 -0600)]
dm: ide: Separate the non-command code into its own file
At present the IDE command code includes both the command-processing code
and the core IDE functions and data structures.
Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly.
With this commit:
- Most CONFIG option are referenced from the non-command code
- The concept of a 'current IDE device' is confined to the command code
This will make it easier to convert this code to driver model.
Simon Glass [Sun, 1 May 2016 17:36:09 +0000 (11:36 -0600)]
dm: scsi: Separate the non-command code into its own file
At present the SCSI command code includes both the command-processing code
and the core SCSI functions and data structures.
Separate the latter into its own file, adding functions as needed to avoid
the command code accessing data structures directly. This functions use the
new legacy block functions.
With this commit:
- There is no CONFIG option referenced from the command code
- The concept of a 'current SCSI device' is confined to the command code
This will make it easier to convert this code to driver model.
Simon Glass [Sun, 1 May 2016 17:36:08 +0000 (11:36 -0600)]
dm: mmc: Add an implementation of the 'devnum' functions
Now that the MMC code accesses devices by number, we can implement this same
interface for driver model, allowing MMC to support using driver model for
block devices.
Simon Glass [Sun, 1 May 2016 17:36:02 +0000 (11:36 -0600)]
dm: scsi: Rename CONFIG_CMD_SCSI to CONFIG_SCSI
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Simon Glass [Sun, 1 May 2016 17:35:54 +0000 (11:35 -0600)]
sandbox: Add string and 16-bit I/O functions
Add outsw() and insw() functions for sandbox, as these are needed by the IDE
code. The functions will not do anything useful if called, but allow the
code to be compiled.
Also add out16() and in16(), required by systemace.
Simon Glass [Sun, 1 May 2016 17:35:53 +0000 (11:35 -0600)]
Allow iotrace byte access to use an address of any size
If an address is used with readb() and writeb() which is smaller than the
expected size (e.g. 32-bit value on a machine with 64-bit addresses), a
warning results. Fix this by adding a cast.
Simon Glass [Sun, 1 May 2016 17:35:52 +0000 (11:35 -0600)]
dm: Rename disk uclass to ahci
This started as 'ahci' and was renamed to 'disk' during code review. But it
seems that this is too generic. Now that we have a 'blk' uclass, we can use
that as the generic piece, and revert to ahci for this.
Simon Glass [Sun, 1 May 2016 17:35:50 +0000 (11:35 -0600)]
dm: sandbox: Add a board for sandbox without CONFIG_BLK
While the driver-model block device support is in progress, it is useful to
build sandbox both with and without CONFIG_BLK. Add a separate board for
the latter.
Simon Glass [Sun, 1 May 2016 17:35:49 +0000 (11:35 -0600)]
Revert "dm: sandbox: Drop the pre-DM host implementation"
Bring this support back so that sandbox can be compiled with CONFIG_BLK. This
allows sandbox to have greater build coverage during the block-device
transition. This can be removed again later.
Peng Fan [Tue, 3 May 2016 02:02:23 +0000 (10:02 +0800)]
dm: gpio: introduce 74x164 driver
Introduce driver to support "fairchild,74hc595" devices.
1. Take linux drivers/drivers/gpio/gpio-74x164.c as reference.
2. Following the naming used in Linux driver with gen_7x164 as the prefix.
3. Enable CONFIG_DM_74X164 to use this driver.
4. Follow Documentation/devicetree/bindings/gpio/gpio-74x164.txt to add device
nodes
5. Tested on i.MX6 UltraLite with 74LV595 using gpio command and oscillograph.
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Chin Liang See <clsee@altera.com> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 3 May 2016 02:02:22 +0000 (10:02 +0800)]
dm: spi: introduce dm api
Introduce dm_spi_claim_bus, dm_spi_release_bus and dm_spi_xfer
Convert spi_claim_bus, spi_release_bus and spi_xfer to use
the new API.
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Jagan Teki <jteki@openedev.com> Acked-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 3 May 2016 02:02:21 +0000 (10:02 +0800)]
dm: spi: soft_spi: switch to use linux compatible string
1. Support compatible string "spi-gpio" which is used by Linux
Linux use different bindings, so use UBOOT_COMPAT and
LINUX_COMPAT to differentiate them.
2. Introduce SPI_MASTER_NO_RX and SPI_MASTER_NO_TX to handle
no rx or no tx case.
3. Tested on i.MX6 UltraLite board with 74LV595 spi-gpio chip.
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 3 May 2016 02:02:20 +0000 (10:02 +0800)]
dm: spi: soft_spi bug fix
When doing xfer, should use device->parent, but not device
When doing bit xfer, should use "!!(tmpdout & 0x80)", but not
"(tmpdout & 0x80)"
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Jagan Teki <jteki@openedev.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Tue, 19 Apr 2016 22:19:30 +0000 (16:19 -0600)]
video: tegra: refuse to bind to disabled dcs
This prevents the following boot-time message on any board where only the
first DC is in use, yet the DC's DT node is enabled:
stdio_add_devices: Video device failed (ret=-22)
(This happens on at least Harmony, Ventana, and likely any other Tegra20
board with display enabled other than Seaboard).
The Tegra DC's DT node represents a display controller. It may itself
drive an integrated RGB display output, or be used by some other display
controller such as HDMI. For this reason the DC node itself is not
enabled/disabled in DT; the DC itself is considered a shared resource, not
the final (board-specific) display output. The node should instantiate a
display output driver only if the rgb subnode is enabled. Other output
drivers are free to use the DC if they are enabled and their DT node
references the DC's DT node. Adapt the Tegra display drivers' bind()
routine to only bind to the DC's DT node if the RGB subnode is enabled.
Now that the display driver does the right thing, remove the workaround
for this issue from Seaboard's DT file.
Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Tue, 19 Apr 2016 22:19:29 +0000 (16:19 -0600)]
dm: core: allow drivers to refuse to bind
In some cases, drivers may not want to bind to a device. Allow bind() to
return -ENODEV in this case, and don't treat this as an error. This can
be useful in situations where some information source other than the DT
node's main status property indicates whether the device should be
enabled, for example other DT properties might indicate this, or the
driver might query non-DT sources such as system fuses or a version number
register.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log
