Yihang Li [Mon, 20 Apr 2026 02:10:44 +0000 (10:10 +0800)]
scsi: hisi_sas: Fix sparse warnings in prep_ata_v3_hw()
In prep_ata_v3_hw(), add cpu_to_le32() to fix warning:
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:1448:26: sparse: sparse: invalid assignment: |=
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:1448:26: sparse: left side has type restricted __le32
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:1448:26: sparse: right side has type unsigned int
Fixes: 8aa580cd9284 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202604191850.IVYPTaML-lkp@intel.com/ Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://patch.msgid.link/20260420021044.3339459-1-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Brian Bunker [Thu, 16 Apr 2026 16:55:12 +0000 (09:55 -0700)]
scsi: scsi_dh_alua: Increase default ALUA timeout to maximum spec value
The ALUA handler maps a 0 value (no implicit transition timeout provided
by the target) to the ALUA_FAILOVER_TIMEOUT constant, currently 60
seconds. This means the kernel already does not accept an infinite
transition time.
However, 60 seconds is insufficient for some arrays that may take longer
to complete ALUA transitions. Since the highest value allowed by the
SCSI specification for the implicit transition timeout is a single byte
(255 seconds), change the default to 255. This way, when a target does
not provide an explicit transition timeout, we default to the maximum
value the spec allows rather than an arbitrary 60 second limit.
Co-developed-by: Krishna Kant <krishna.kant@purestorage.com> Signed-off-by: Krishna Kant <krishna.kant@purestorage.com> Co-developed-by: Riya Savla <rsavla@purestorage.com> Signed-off-by: Riya Savla <rsavla@purestorage.com> Signed-off-by: Brian Bunker <brian@purestorage.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Link: https://patch.msgid.link/20260416165512.26497-2-brian@purestorage.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Henzl [Tue, 14 Apr 2026 12:41:18 +0000 (14:41 +0200)]
scsi: smartpqi: Silence a recursive lock warning
On systems with multiple controllers debug kernel shows
WARNING: possible recursive locking detected
during shutdown.
Each controller does have its own ctrl_info (and mutex) and that isn't
correctly recognized by debug kernel. Suppress the warning by releasing
the mutex at the end of pqi_shutdown().
The HBA firmware reports NVMe MDTS values based on the underlying drive
capability. However, because the driver allocates a fixed 4K buffer for
the PRP list, accommodating at most 512 entries, the driver supports a
maximum I/O transfer size of 2 MiB.
Limit max_hw_sectors to the smaller of the reported MDTS and the 2 MiB
driver limit to prevent issuing oversized I/O that may lead to a kernel
oops.
sg_start_req() is called from normal user context and can sleep when
waiting for memory. Switch it to use GFP_KERNEL, which fixes allocation
failures seen with the bio_alloc rework.
Fixes: b520c4eef83d ("block: split bio_alloc_bioset more clearly into a fast and slowpath") Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Link: https://patch.msgid.link/20260415060813.807659-2-hch@lst.de Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark Harmstone [Thu, 16 Apr 2026 17:15:23 +0000 (18:15 +0100)]
btrfs: fix double-decrement of bytes_may_use in submit_one_async_extent()
submit_one_async_extent() calls btrfs_reserve_extent(), which decrements
bytes_may_use. If the call btrfs_create_io_em() fails, we jump to
out_free_reserve, which calls extent_clear_unlock_delalloc().
Because we're specifying EXTENT_DO_ACCOUNTING, i.e.
EXTENT_CLEAR_META_RESV | EXTENT_CLEAR_DATA_RESV, this decreases
bytes_may_use again. This can lead to problems later on, as an initial
write can fail only for the writeback to silently ENOSPC.
Fix this by replacing EXTENT_DO_ACCOUNTING with EXTENT_CLEAR_META_RESV.
This parallels a4fe134fc1d8eb ("btrfs: fix a double release on reserved
extents in cow_one_range()"), which is the same fix in cow_one_range().
Fixes: 151a41bc46df ("Btrfs: fix what bits we clear when erroring out from delalloc") Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Mark Harmstone <mark@harmstone.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: check return value of btrfs_partially_delete_raid_extent()
btrfs_partially_delete_raid_extent() returns an error code (e.g.
-ENOMEM from kzalloc(), or errors from btrfs_del_item/btrfs_insert_item()),
but all three call sites in btrfs_delete_raid_extent() discard the
return value, silently losing errors and potentially leaving the stripe
tree in an inconsistent state.
Fix by capturing the return value into ret at all three call sites and
breaking out of the loop on error where appropriate.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: robbieko <robbieko@synology.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: handle -EAGAIN from btrfs_duplicate_item and refresh stale leaf pointer
In the 'punch a hole' case of btrfs_delete_raid_extent(),
btrfs_duplicate_item() can return -EAGAIN when the leaf needs to be
split and the path becomes invalid. The old code treats any error as
fatal and breaks out of the loop.
Additionally, btrfs_duplicate_item() may trigger setup_leaf_for_split()
which can reallocate the leaf node. The code continues using the old
leaf pointer, leading to use-after-free or stale data access.
Fix both issues by:
- Handling -EAGAIN specifically: release the path and retry the loop.
- Refreshing leaf = path->nodes[0] after successful duplication.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: robbieko <robbieko@synology.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: replace ASSERT with proper error handling in stripe lookup fallback
After falling back to the previous item in btrfs_delete_raid_extent(),
the code uses ASSERT(found_start <= start) to verify the found extent
actually precedes our target range. If the B-tree state is unexpected
(e.g. no overlapping extent exists), this triggers a kernel BUG/panic
in debug builds, or silently continues with wrong data otherwise.
Replace the ASSERT with a proper bounds check that returns -ENOENT if
the found extent does not actually overlap with the start position.
Signed-off-by: robbieko <robbieko@synology.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: fix wrong min_objectid in btrfs_previous_item() call
When found_start > start and slot == 0, btrfs_previous_item() is called
with min_objectid=start to find the previous stripe extent. However, the
previous stripe extent we are looking for has objectid < start (it starts
before our deletion range), so passing start as min_objectid prevents
finding it.
Fix by passing 0 as min_objectid to allow finding any preceding stripe
extent regardless of its objectid.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: robbieko <robbieko@synology.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: fix raid stripe search missing entries at leaf boundaries
In btrfs_delete_raid_extent(), the search key uses offset=0. When the
target stripe entry is the first item on a leaf, btrfs_search_slot()
may land on the previous leaf and decrementing the slot from nritems
still points to the wrong entry, causing the stripe extent to be
silently missed.
Fix this by searching with offset=(u64)-1 instead. Since no real stripe
entry has this offset, btrfs_search_slot() always returns 1 with the
slot pointing past the last matching objectid entry. Then unconditionally
decrement the slot with a proper slots[0]==0 early-exit check to handle
the case where no matching entry exists.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: robbieko <robbieko@synology.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: copy devid in btrfs_partially_delete_raid_extent()
When btrfs_partially_delete_raid_extent() rebuilds a truncated/shifted
stripe extent into newitem, the loop copies the physical address for
each stride but forgets to copy the devid. The resulting item written
back to the stripe tree has zeroed-out devids, corrupting the stripe
mapping.
Fix this by reading the devid with btrfs_raid_stride_devid() and
writing it into the new item with btrfs_set_stack_raid_stride_devid()
before copying the physical address.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: robbieko <robbieko@synology.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Thu, 9 Apr 2026 14:46:51 +0000 (15:46 +0100)]
btrfs: fix missing last_unlink_trans update when removing a directory
When removing a directory we are not updating its last_unlink_trans field,
which can result in incorrect fsync behaviour in case some one fsyncs the
directory after it was removed because it's holding a file descriptor on
it.
The problem is that such a fsync should have result in a fallback to a
transaction commit, but that did not happen because through the
btrfs_rmdir() we never update the directory's last_unlink_trans field.
Any inode that had a link removed must have its last_unlink_trans updated
to the ID of transaction used for the operation, otherwise fsync and log
replay will not work correctly.
btrfs_rmdir() calls btrfs_unlink_inode() and through that call chain we
never call btrfs_record_unlink_dir() in order to update last_unlink_trans.
However btrfs_unlink(), which is used for unlinking regular files, calls
btrfs_record_unlink_dir() and then calls btrfs_unlink_inode(). So fix
this by moving the call to btrfs_record_unlink_dir() from btrfs_unlink()
to btrfs_unlink_inode().
Mark Harmstone [Mon, 23 Mar 2026 17:17:01 +0000 (17:17 +0000)]
btrfs: don't clobber errors in add_remap_tree_entries()
In add_remap_tree_entries(), we only process a certain number of entries
at a time, meaning we may need to loop.
But because we weren't checking the return value of btrfs_insert_empty_items()
within the loop, this meant that if the last iteration of the loop
succeeded but a previous iteration failed, we were erroneously returning
0.
Fix this by breaking the loop early if btrfs_insert_empty_items() fails.
Fixes: b56f35560b82 ("btrfs: handle setting up relocation of block group with remap-tree") Signed-off-by: Mark Harmstone <mark@harmstone.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: enable shutdown ioctl for non-experimental builds
Although commit 304076527c38 ("btrfs: move shutdown and remove_bdev
callbacks out of experimental features") tries to move both shutdown and
remove_bdev out of experimental features, that commit has only addressed
the super block operation callback, the ioctl one is left untouched.
Fix that missing aspect by also moving shutdown ioctl out of
experimental features.
Since we're here, also add unknown flag detection to reject any
unsupported shutdown flags.
Fixes: 304076527c38 ("btrfs: move shutdown and remove_bdev callbacks out of experimental features") Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: apply first key check for readahead when possible
Currently for tree block readahead we never pass a
btrfs_tree_parent_check with @has_first_key set.
Without @has_first_key set, btrfs will skip the following extra
checks:
- Header generation check
This is a minor one.
- Empty leaf/node checks
This is more serious, for certain trees like the csum tree, they are
allowed to be empty, thus an empty leaf can pass the tree checker.
But if there is a parent node for such an empty leaf, it indicates
corruption.
Without @has_first_key set, we can no longer detect such a problem.
In fact there is already a fuzzed image report that a corrupted csum
leaf which has zero nritems but still has a parent node can trigger
a BUG_ON() during csum deletion.
However there are only two call sites of btrfs_readahead_tree_block():
- Inside relocate_tree_blocks()
At this call site we are trying to grab the first key of the tree
block, thus we are not able to pass a @first_key parameter.
- Inside btrfs_readahead_node_child()
This is the more common call site, where we have the parent node and
want to readahead the child tree blocks.
In this case we can easily grab the node key and pass it for checks.
Add a new parameter @first_key to btrfs_readahead_tree_block() and pass
the node key to it inside btrfs_readahead_node_child().
This should plug the gap in empty leaf detection during readahead.
Mark Harmstone [Mon, 23 Mar 2026 17:16:43 +0000 (17:16 +0000)]
btrfs: abort transaction in do_remap_reloc_trans() on failure
If one of the calls made by do_remap_reloc_trans() fails, we can leave
the remap tree in an inconsistent state. Abort the transaction if this
happens, to prevent the corrupt state from reaching the disk.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Mark Harmstone <mark@harmstone.com> Signed-off-by: David Sterba <dsterba@suse.com>
Mark Harmstone [Mon, 23 Mar 2026 12:59:57 +0000 (12:59 +0000)]
btrfs: fix bytes_may_use leak in do_remap_reloc_trans()
If the call to btrfs_reserve_extent() in do_remap_reloc_trans() returns
a smaller extent than we asked for, currently we're not undoing the
bytes_may_use change that we made. Fix this by calling
btrfs_space_info_update_bytes_may_use() again for the difference.
Fixes: fd6594b1446c ("btrfs: replace identity remaps with actual remaps when doing relocations") Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Mark Harmstone <mark@harmstone.com> Signed-off-by: David Sterba <dsterba@suse.com>
Mark Harmstone [Mon, 23 Mar 2026 12:59:47 +0000 (12:59 +0000)]
btrfs: fix bytes_may_use leak in move_existing_remap()
If the call to btrfs_reserve_extent() in move_existing_remap() returns a
smaller extent than we asked for, currently we're not undoing the
bytes_may_use change that we made. Fix this by calling
btrfs_space_info_update_bytes_may_use() again for the difference.
Fixes: bbea42dfb91f ("btrfs: move existing remaps before relocating block group") Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Mark Harmstone <mark@harmstone.com> Signed-off-by: David Sterba <dsterba@suse.com>
Jie Meng [Mon, 13 Apr 2026 17:23:11 +0000 (10:23 -0700)]
bpf: Exhaustive test coverage for signed division and modulo
Extend lib/test_bpf.c to provide comprehensive test coverage for BPF
signed division (SDIV) and signed modulo (SMOD) instructions, both
32-bit and 64-bit variants with immediate operands.
Introduce F_ALU32 and F_SIGNED flags to replace the less readable
bool alu32 and s16 off parameters throughout the test helpers. The
BPF instruction 'off' field is derived from flags only at the point
of instruction encoding.
Changes:
- Add enum { F_ALU32 = 1, F_SIGNED = 2 } for readable test flags.
- __bpf_alu_result(): take u32 flags instead of separate signed/alu32
parameters. Narrows operands internally for ALU32 (unsigned via u32
cast, signed via s32 cast) before computing the reference result.
- __bpf_emit_alu64_imm(), __bpf_emit_alu32_imm(): pass flags through
to __bpf_alu_result, derive 'off' for instruction encoding locally.
- __bpf_fill_alu_imm_regs(): take u32 flags, use F_ALU32/F_SIGNED for
operand setup and single-line __bpf_alu_result() call.
- __bpf_fill_alu_shift(), __bpf_fill_alu_shift_same_reg(): convert
bool alu32 parameter to u32 flags for consistency.
- New test fill functions: bpf_fill_alu{32,64}_{sdiv,smod}_imm() and
bpf_fill_alu{32,64}_{sdiv,smod}_imm_regs(), each testing all
immediate value magnitudes and all register pair combinations.
- All existing unsigned tests updated to use flags (0 or F_ALU32),
preserving backward compatibility.
8 new test cases added:
ALU64_SDIV_K, ALU64_SMOD_K (immediate magnitudes + register combos)
ALU32_SDIV_K, ALU32_SMOD_K (immediate magnitudes + register combos)
====================
bpf: Extend BTF UAPI vlen, kinds to use unused bits
Currently BTF types can have a maximum of 65535 vlen-specified
objects. While this limit has not yet been surpassed for existing
cases (struct/union fields, enum values, function arguments and
datasec), upcoming BTF location information - specifically inline
sites - will hit that limit. Utilize unused BTF info bits in
struct btf_type to increase limit to 24-bits (over 16 million).
This is more than an order of magnitude greater than inline
site counts for the kernel (~400,000) so should be enough for
the near future at least.
Similarly, struct btf_type uses 5 bits for BTF kind values;
currently we use 20 kinds, but BTF location information will
take another 3, and conceivably providing better support for Rust
types in BTF (now that modules can be built using Rust) could
push us close to the max of 31. Use 2 unused bits to provide
a max possible kind of 127.
Patch 1 handles UAPI and kernel-related changes.
Patch 2 updates libbpf to have btf_vlen() return a __u32 instead
of __u16 and updates consumers in libbpf accordingly. Also adds
bounds checking for max vlen.
Patch 3 cleans up __u16 vlen usage in bpftool.
Patch 4 fixes up a test that relies on BTF info overflowing
maximum kind value; fix up the expected error to be an
invalid kind rather than (now impossible) invalid btf_info.
Patch 5 fixes up __u16 vlen usage in selftests/bpf.
Patch 6 syncs BTF documentation with UAPI changes.
Changes since v2 [1]:
- dropped backwards-compatibility macros (Alexei, patch 1)
- added additional vlen bounds check in btf__add_field()
(sashiko, bpf bot, patch 2)
- dropped sanitization check in libbpf as older kernels will
reject BTF with extended vlen/kinds using BTF info mask
(Alexei)
- fix more vlen assumptions in prog_test/ctx_rewrite.c
(sashiko, patch 5)
Changes since v1 [2]:
- added redundant macros to UAPI in case enum switch for BTF_MAX*
values causes problems (sashiko, patch 1)
- updated feature test to use BTF loading rather than vmlinux BTF
lookup, in line with other BTF feature tests (sashiko, patch 3)
- fixed up a few more kernel, libbpf, bpftool instances of __u16 usage
(bpf bot, sashiko, patches 1, 2, 4)
- fixed up sanitize selftest cleanup (Mykyta, patch 5)
- used unlikely-to-be-used kind (sashiko, patch 6)
- fixed a few lingering selftests uses of __u16 for kind (patch 7)
- update btf.rst with new vlen, kind sizes (patch 8)
Alan Maguire [Fri, 17 Apr 2026 14:30:21 +0000 (15:30 +0100)]
selftests/bpf: Fix up btf/invalid test for extended kind
With extended kinds, 32 becomes a valid (but not used)
BTF info kind value; fix up the test to check for the
"Invalid kind" rather than "Invalid btf_info" message.
Since all bits are used in BTF info, it is no longer
possible to craft an invalid BTF info value. Use
127 (new maximum possible kind value).
Alan Maguire [Fri, 17 Apr 2026 14:30:19 +0000 (15:30 +0100)]
libbpf: Adjust btf_vlen() to return a __u32
Now that vlen is 24 bits, btf_vlen() must return a __u32.
Adjust use cases in libbpf accordingly. Also add error
handling to avoid vlen overflow in btf_type_inc_vlen().
Alan Maguire [Fri, 17 Apr 2026 14:30:18 +0000 (15:30 +0100)]
bpf: Extend BTF UAPI vlen, kinds to use unused bits
BTF maximum vlen is encoded using 16 bits with a maximum vlen
of 65535. This has sufficed for structs, function parameters
and enumerated type values. However, with upcoming BTF location
information - in particular information about inline sites -
this limit is surpassed. Use bits 16-23 - currently unused in
BTF info - to extend to 24 bits, giving a max vlen of (2^24 - 1),
or 16 million.
Also extend BTF kind encoding from 5 to 7 bits, giving a maximum
available number of kinds of 128. Since with the BTF location work
we use another 3 kinds, we are fast approaching the current limit
of 32.
Convert BTF_MAX_* values to enums to allow them to be encoded in
kernel BTF; this will allow us to detect if the running kernel
supports a 24-bit vlen or not. Add one for max _possible_
(not used) kind.
Fix up a few places in the kernel where a 16-bit vlen is assumed;
remove BTF_INFO_MASK as now all bits are used.
The vlen expansion was suggested by Andrii in [1]; the kind expansion
is tackled here too as it may be needed also to support new kinds
in BTF.
tracing: tell git to ignore the generated 'undefsyms_base.c' file
This odd file was added to automatically figure out tool-generated
symbols.
Honestly, it *should* have been just a real honest-to-goodness regular
file in git, instead of having strange code to generate it in the
Makefile, but that is not how that silly thing works. So now we need to
ignore it explicitly.
Fixes: 1211907ac0b5 ("tracing: Generate undef symbols allowlist for simple_ring_buffer") Cc: Vincent Donnefort <vdonnefort@google.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Steven Rostedt (Google) <rostedt@goodmis.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Marc Zyngier <maz@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'linux_kselftest-next-7.1-next-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"Fix regressions in non-bash shells and busybox support, and revert a
commit that regressed in build and installation when one or more tests
fail to build.
Fix duplicated test number reporting introduced in ktap support patch"
* tag 'linux_kselftest-next-7.1-next-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix duplicated test number reporting
selftests: Fix runner.sh for non-bash shells
selftests: Fix runner.sh busybox support
selftests: Deescalate error reporting
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
"The main 'feature' is a workaround for C1-Pro erratum 4193714
requiring IPIs during TLB maintenance if a process is running in user
space with SME enabled.
The hardware acknowledges the DVMSync messages before completing
in-flight SME accesses, with security implications. The workaround
makes use of the mm_cpumask() to track the cores that need
interrupting (arm64 hasn't used this mask before).
The rest are fixes for MPAM, CCA and generated header that turned up
during the merging window or shortly before.
Summary:
Core features:
- Add workaround for C1-Pro erratum 4193714 - early CME (SME unit)
DVMSync acknowledgement. The fix consists of sending IPIs on TLB
maintenance to those CPUs running in user space with SME enabled
- Include kernel-hwcap.h in list of generated files (missed in a
recent commit generating the KERNEL_HWCAP_* macros)
CCA:
- Fix RSI_INCOMPLETE error check in arm-cca-guest
MPAM:
- Fix an unmount->remount problem with the CDP emulation,
uninitialised variable and checker warnings"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm_mpam: resctrl: Make resctrl_mon_ctx_waiters static
arm_mpam: resctrl: Fix the check for no monitor components found
arm_mpam: resctrl: Fix MBA CDP alloc_capable handling on unmount
virt: arm-cca-guest: fix error check for RSI_INCOMPLETE
arm64/hwcap: Include kernel-hwcap.h in list of generated files
arm64: errata: Work around early CME DVMSync acknowledgement
arm64: cputype: Add C1-Pro definitions
arm64: tlb: Pass the corresponding mm to __tlbi_sync_s1ish()
arm64: tlb: Introduce __tlbi_sync_s1ish_{kernel,batch}() for TLB maintenance
Merge tag 'sh-for-v7.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Two patches from Thomas Zimmermann, one by Tim Bird and one by Thomas
Weißschuh.
The first patch by Thomas Zimmermann adds a missing include in dac.h
for SH-3 which became necessary after 243ce64b2b37 ("backlight: Do not
include <linux/fb.h> in header file") which made __raw_readb() and
__raw_writeb() inaccessible in dac.h.
Thomas' second patch drops CONFIG_FIRMWARE_EDID for SH as it depends
on X86 or EFI_GENERIC_STUB which are not defined on SH for obvious
reasons.
The patch by Tim Bird fixes just a small typo in two SPDX ID lines
which he stumbled over by accident.
And, least but not last, the patch by Thomas Weißschuh removes the
CONFIG_VSYSCALL reference from UAPI. This was necessary as the
definition of AT_SYSINFO_EHDR was gated between CONFIG_VSYSCALL to
avoid a default gate VMA to be created. However that default gate VMA
was removed entirely in commit a6c19dfe3994 (arm64,ia64,ppc,s390,
sh,tile,um,x86,mm: remove default gate area)"
* tag 'sh-for-v7.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: Drop CONFIG_FIRMWARE_EDID from defconfig files
sh: Remove CONFIG_VSYSCALL reference from UAPI
sh: Fix typo in SPDX license ID lines
sh: Include <linux/io.h> in dac.h
Merge tag 'printk-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Fix printk ring buffer initialization and sanity checks
- Workaround printf kunit test compilation with gcc < 12.1
- Add IPv6 address printf format tests
- Misc code and documentation cleanup
* tag 'printk-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printf: Compile the kunit test with DISABLE_BRANCH_PROFILING DISABLE_BRANCH_PROFILING
lib/vsprintf: use bool for local decode variable
lib/hexdump: print_hex_dump_bytes() calls print_hex_dump_debug()
printk: ringbuffer: fix errors in comments
printk_ringbuffer: Add sanity check for 0-size data
printk_ringbuffer: Fix get_data() size sanity check
printf: add IPv6 address format tests
printk: Fix _DESCS_COUNT type for 64-bit systems
Merge tag 'timers-urgent-2026-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix timer stalls caused by incorrect handling of the
dev->next_event_forced flag"
* tag 'timers-urgent-2026-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Add missing resets of the next_event_forced flag
rtmutex: Use waiter::task instead of current in remove_waiter()
remove_waiter() is used by the slowlock paths, but it is also used for
proxy-lock rollback in rt_mutex_start_proxy_lock() when invoked from
futex_requeue().
In the latter case waiter::task is not current, but remove_waiter()
operates on current for the dequeue operation. That results in several
problems:
1) the rbtree dequeue happens without waiter::task::pi_lock being held
2) the waiter task's pi_blocked_on state is not cleared, which leaves a
dangling pointer primed for UAF around.
3) rt_mutex_adjust_prio_chain() operates on the wrong top priority waiter
task
Use waiter::task instead of current in all related operations in
remove_waiter() to cure those problems.
[ tglx: Fixup rt_mutex_adjust_prio_chain(), add a comment and amend the
changelog ]
Fixes: 8161239a8bcc ("rtmutex: Simplify PI algorithm and make highest prio task get lock") Reported-by: Yuan Tan <yuantan098@gmail.com> Reported-by: Yifan Wu <yifanwucs@gmail.com> Reported-by: Juefei Pu <tomapufckgml@gmail.com> Reported-by: Xin Liu <bird@lzu.edu.cn> Signed-off-by: Keenan Dong <keenanat2000@gmail.com> Signed-off-by: Thomas Gleixner <tglx@kernel.org> Cc: stable@vger.kernel.org
KVM: selftests: Replace "paddr" with "gpa" throughout
Replace all variations of "paddr" variables in KVM selftests with "gpa",
with the exception of the ELF structures, as those fields are not specific
to guest virtual addresses, to complete the conversion from vm_paddr_t to
gpa_t.
KVM: selftests: Replace "vaddr" with "gva" throughout
Replace all variations of "vaddr" variables in KVM selftests with "gva",
with the exception of the ELF structures, as those fields are not specific
to guest virtual addresses, to complete the conversion from vm_vaddr_t to
gva_t.
Opportunistically use gva_t instead of u64 for relevant variables, and
fixup indentation as appropriate.
Rename arm64's translate_to_host_paddr() to translate_hva_to_hpa() and
update variable names to match, as using "vaddr" and "paddr" terminology
is super confusing due to selftests using those exact names for *guest*
addresses.
Opportunisitically drop superfluous local page_addr and paddr variables.
Now that KVM selftests use gva_t instead of vm_vaddr_t, rename the helper
for populating the initial GVA bitmap to drop the defunct terminology and
use "vm" for the scope.
Opportunistically fixup the declaration of the API, which has been broken
since day 1. The flaw went unnoticed because the sole caller is defined
after the weak version, i.e. can see the prototype without a previous
declaration.
Now that KVM selftests use gva_t instead of vm_vaddr_t, rename the API
for finding an unused range of virtual memory to drop the defunct
terminology and use "vm" for the scope.
Opportunistically clean up the function comment to drop superfluous
and redundant information.
KVM: selftests: Drop "vaddr_" from APIs that allocate memory for a given VM
Now that KVM selftests use gva_t instead of vm_vaddr_t, drop "vaddr_" from
the core memory allocation APIs as the information is extraneous and does
more harm than good. E.g. the APIs don't _just_ allocate virtual memory,
they allocate backing physical memory and install mappings in the guest
page tables. And as proven by kmalloc() and malloc(), developers generally
expect that allocations come with a working virtual address.
Opportunistically clean up the function comment for vm_alloc(), and drop
the misleading and superfluous comments for its wrappers.
David Matlack [Mon, 20 Apr 2026 21:19:55 +0000 (14:19 -0700)]
KVM: selftests: Use u8 instead of uint8_t
Use u8 instead of uint8_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/uint8_t/u8/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
David Matlack [Mon, 20 Apr 2026 21:19:54 +0000 (14:19 -0700)]
KVM: selftests: Use s16 instead of int16_t
Use s16 instead of int16_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/int16_t/s16/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
David Matlack [Mon, 20 Apr 2026 21:19:53 +0000 (14:19 -0700)]
KVM: selftests: Use u16 instead of uint16_t
Use u16 instead of uint16_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/uint16_t/u16/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
David Matlack [Mon, 20 Apr 2026 21:19:52 +0000 (14:19 -0700)]
KVM: selftests: Use s32 instead of int32_t
Use s32 instead of int32_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/int32_t/s32/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
David Matlack [Mon, 20 Apr 2026 21:19:51 +0000 (14:19 -0700)]
KVM: selftests: Use u32 instead of uint32_t
Use u32 instead of uint32_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/uint32_t/u32/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
David Matlack [Mon, 20 Apr 2026 21:19:50 +0000 (14:19 -0700)]
KVM: selftests: Use s64 instead of int64_t
Use s64 instead of int64_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/int64_t/s64/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
David Matlack [Mon, 20 Apr 2026 21:19:49 +0000 (14:19 -0700)]
KVM: selftests: Use u64 instead of uint64_t
Use u64 instead of uint64_t to make the KVM selftests code more concise
and more similar to the kernel (since selftests are primarily developed
by kernel developers).
This commit was generated with the following command:
git ls-files tools/testing/selftests/kvm | xargs sed -i 's/uint64_t/u64/g'
Then by manually adjusting whitespace to make checkpatch.pl happy.
Include <linux/types.h> in include/kvm_util_types.h, iinclude/test_util.h,
and include/x86/pmu.h to pick up the tools-defined u64. Arguably, all
headers (especially kvm_util_types.h) should have already been including
stdint.h to get uint64_t from the libc headers, but the missing dependency
only rears its head once KVM uses u64 instead of uint64_t.
David Matlack [Mon, 20 Apr 2026 21:19:48 +0000 (14:19 -0700)]
KVM: selftests: Use gpa_t for GPAs in Hyper-V selftests
Fix various Hyper-V selftests to use gpa_t for variables that contain
guest physical addresses, rather than gva_t. In practice, the bugs are
benign as both gva_t and gpa_t are u64 typedefs, i.e. gpa_t and gva_t are
interchangeable from a functional perspective, the code is just confusing.
netfilter: nfnetlink_osf: fix potential NULL dereference in ttl check
The nf_osf_ttl() function accessed skb->dev to perform a local interface
address lookup without verifying that the device pointer was valid.
Additionally, the implementation utilized an in_dev_for_each_ifa_rcu
loop to match the packet source address against local interface
addresses. It assumed that packets from the same subnet should not see a
decrement on the initial TTL. A packet might appear it is from the same
subnet but it actually isn't especially in modern environments with
containers and virtual switching.
Remove the device dereference and interface loop. Replace the logic with
a switch statement that evaluates the TTL according to the ttl_check.
Fixes: 11eeef41d5f6 ("netfilter: passive OS fingerprint xtables match") Reported-by: Kito Xu (veritas501) <hxzene@gmail.com> Closes: https://lore.kernel.org/netfilter-devel/20260414074556.2512750-1-hxzene@gmail.com/ Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nfnetlink_osf: fix out-of-bounds read on option matching
In nf_osf_match(), the nf_osf_hdr_ctx structure is initialized once
and passed by reference to nf_osf_match_one() for each fingerprint
checked. During TCP option parsing, nf_osf_match_one() advances the
shared ctx->optp pointer.
If a fingerprint perfectly matches, the function returns early without
restoring ctx->optp to its initial state. If the user has configured
NF_OSF_LOGLEVEL_ALL, the loop continues to the next fingerprint.
However, because ctx->optp was not restored, the next call to
nf_osf_match_one() starts parsing from the end of the options buffer.
This causes subsequent matches to read garbage data and fail
immediately, making it impossible to log more than one match or logging
incorrect matches.
Instead of using a shared ctx->optp pointer, pass the context as a
constant pointer and use a local pointer (optp) for TCP option
traversal. This makes nf_osf_match_one() strictly stateless from the
caller's perspective, ensuring every fingerprint check starts at the
correct option offset.
Fixes: 1a6a0951fc00 ("netfilter: nfnetlink_osf: add missing fmatch check") Suggested-by: Florian Westphal <fw@strlen.de> Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipvs: fix MTU check for GSO packets in tunnel mode
Currently, IPVS skips MTU checks for GSO packets by excluding them with
the !skb_is_gso(skb) condition. This creates problems when IPVS tunnel
mode encapsulates GSO packets with IPIP headers.
The issue manifests in two ways:
1. MTU violation after encapsulation:
When a GSO packet passes through IPVS tunnel mode, the original MTU
check is bypassed. After adding the IPIP tunnel header, the packet
size may exceed the outgoing interface MTU, leading to unexpected
fragmentation at the IP layer.
2. Fragmentation with problematic IP IDs:
When net.ipv4.vs.pmtu_disc=1 and a GSO packet with multiple segments
is fragmented after encapsulation, each segment gets a sequentially
incremented IP ID (0, 1, 2, ...). This happens because:
a) The GSO packet bypasses MTU check and gets encapsulated
b) At __ip_finish_output, the oversized GSO packet is split into
separate SKBs (one per segment), with IP IDs incrementing
c) Each SKB is then fragmented again based on the actual MTU
This sequential IP ID allocation differs from the expected behavior
and can cause issues with fragment reassembly and packet tracking.
Fix this by properly validating GSO packets using
skb_gso_validate_network_len(). This function correctly validates
whether the GSO segments will fit within the MTU after segmentation. If
validation fails, send an ICMP Fragmentation Needed message to enable
proper PMTU discovery.
"Historically this is not an issue, even for normal base hooks: the data
path doesn't use the original nf_hook_ops that are used to register the
callbacks.
However, in v5.14 I added the ability to dump the active netfilter
hooks from userspace.
This code will peek back into the nf_hook_ops that are available
at the tail of the pointer-array blob used by the datapath.
The nat hooks are special, because they are called indirectly from
the central nat dispatcher hook. They are currently invisible to
the nfnl hook dump subsystem though.
But once that changes the nat ops structures have to be deferred too."
Update nf_nat_register_fn() to deal with partial exposition of the hooks
from error path which can be also an issue for nfnetlink_hook.
Fixes: e2cf17d3774c ("netfilter: add new hook nfnl subsystem") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: xtables: restrict several matches to inet family
This is a partial revert of:
commit ab4f21e6fb1c ("netfilter: xtables: use NFPROTO_UNSPEC in more extensions")
to allow ipv4 and ipv6 only.
- xt_mac
- xt_owner
- xt_physdev
These extensions are not used by ebtables in userspace.
Moreover, xt_realm is only for ipv4, since dst->tclassid is ipv4
specific.
Fixes: ab4f21e6fb1c ("netfilter: xtables: use NFPROTO_UNSPEC in more extensions") Reported-by: "Kito Xu (veritas501)" <hxzene@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Xiang Mei [Tue, 14 Apr 2026 22:14:01 +0000 (15:14 -0700)]
netfilter: nfnetlink_osf: fix divide-by-zero in OSF_WSS_MODULO
nf_osf_match_one() computes ctx->window % f->wss.val in the
OSF_WSS_MODULO branch with no guard for f->wss.val == 0. A
CAP_NET_ADMIN user can add such a fingerprint via nfnetlink; a
subsequent matching TCP SYN divides by zero and panics the kernel.
Reject the bogus fingerprint in nfnl_osf_add_callback() above the
per-option for-loop. f->wss is per-fingerprint, not per-option, so
the check must run regardless of f->opt_num (including 0). Also
reject wss.wc >= OSF_WSS_MAX; nf_osf_match_one() already treats that
as "should not happen".
io_uring: fix iowq_limits data race in tctx node addition
__io_uring_add_tctx_node() reads ctx->int_flags and
ctx->iowq_limits[0..1] without holding ctx->uring_lock, while
io_register_iowq_max_workers() writes these same fields under the lock.
Mostly an application problem if you try and make these race, but let's
silence KCSAN by just grabbing the ->uring_lock around the operation.
This is a slow path operation anyway, and ->uring_lock will be grabbed
by submission right after anyway.
Fixes: 2e480058ddc2 ("io-wq: provide a way to limit max number of workers") Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rick Edgecombe [Thu, 9 Apr 2026 18:43:30 +0000 (11:43 -0700)]
x86/shstk: Prevent deadlock during shstk sigreturn
During sigreturn the shadow stack signal frame is popped. The kernel does
this by reading the shadow stack using normal read accesses. When it can't
assume the memory is shadow stack, it takes extra steps to makes sure it is
reading actual shadow stack memory and not other normal readable memory. It
does this by holding the mmap read lock while doing the access and checking
the flags of the VMA.
Unfortunately that is not safe. If the read of the shadow stack sigframe
hits a page fault, the fault handler will try to recursively grab another
mmap read lock. This normally works ok, but if a writer on another CPU is
also waiting, the second read lock could fail and cause a deadlock.
Fix this by not holding mmap lock during the read access to userspace.
Instead use mmap_lock_speculate_...() to watch for changes between dropping
mmap lock and the userspace access. Retry if anything grabbed an mmap write
lock in between and could have changed the VMA.
These mmap_lock_speculate_...() helpers use mm::mm_lock_seq, which is only
available when PER_VMA_LOCK is configured. So make X86_USER_SHADOW_STACK
depend on it. On x86, PER_VMA_LOCK is a default configuration for SMP
kernels. So drop support for the other configs under the assumption that
the !SMP shadow stack user base does not exist.
Currently there is a check that skips the lookup work when the SSP can be
assumed to be on a shadow stack. While reorganizing the function, remove
the optimization to make the tricky code flows more common, such that
issues like this cannot escape detection for so long.
Fixes: 7fad2a432cd3 ("x86/shstk: Check that signal frame is shadow stack mem") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Thomas Gleixner <tglx@kernel.org> Reviewed-by: Dave Hansen <dave.hansen@intel.com> Reviewed-by: Thomas Gleixner <tglx@kernel.org> Cc: stable@vger.kernel.org
in io_wq_put_and_exit(), which can be triggered with memory allocation
fault injection. Ensure that the io_wq is marked as exiting to silence
this warning trigger.
drm/nouveau: fix u32 overflow in pushbuf reloc bounds check
nouveau_gem_pushbuf_reloc_apply() validates each relocation with
if (r->reloc_bo_offset + 4 > nvbo->bo.base.size)
but reloc_bo_offset is __u32 (uapi/drm/nouveau_drm.h) and the integer
literal 4 promotes to unsigned int, so the addition is performed in 32
bits and wraps before the comparison against the size_t bo size.
Cast to u64 so the addition happens in 64-bit arithmetic.
Cc: Lyude Paul <lyude@redhat.com> Cc: Danilo Krummrich <dakr@kernel.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@gmail.com> Cc: Simona Vetter <simona@ffwll.ch> Reported-by: Anthropic Cc: stable <stable@kernel.org> Assisted-by: gkh_clanker_t1000 Fixes: a1606a9596e5 ("drm/nouveau: new gem pushbuf interface, bump to 0.0.16") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Add Fixes: tag. - Danilo ] Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Steven Rostedt [Mon, 20 Apr 2026 18:24:26 +0000 (14:24 -0400)]
ktest: Fix the month in the name of the failure directory
The Perl localtime() function returns the month starting at 0 not 1. This
caused the date produced to create the directory for saving files of a
failed run to have the month off by one.
Cc: stable@vger.kernel.org Cc: John 'Warthog9' Hawley <warthog9@kernel.org> Link: https://patch.msgid.link/20260420142426.33ad0293@fedora Fixes: 7faafbd69639b ("ktest: Add open and close console and start stop monitor") Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Merge tag 'platform-drivers-x86-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Ilpo Järvinen:
"asus-wmi:
- Retain battery charge threshold during boot which avoids
unsolicited change to 100%. Return -ENODATA when the limit
is not yet known
- Improve screenpad power/brightness handling consistency
- Fix screenpad brightness range
bitland-mifs-wmi:
- Add driver for Bitland laptops (supports platform profile,
hwmon, kbd backlight, gpu mode, hotkeys, and fan boost)
dell_rbu:
- Fix using uninitialized value in sysfs write function
dell-wmi-sysman:
- Respect destination length when constructing enum strings
hp-wmi:
- Propagate fan setting apply failures and log an error
- Fix sysfs write vs work handler cancel_delayed_work_sync() deadlock
- Correct keepalive schedule_delayed_work() to mod_delayed_work()
- Fix u8 underflows in GPU delta calculation
- Use mutex to protect fan pwm/mode
- Ignore kbd backlight and FnLock key events that are handled by FW
- Fix fan table parsing (use correct field)
- Add support for Omen 14-fb0xxx, 16-n0xxx, 16-wf1xxx, and
Omen MAX 16-ak0xxxx
input: trackpoint & thinkpad_acpi:
- Enable doubletap by default and add sysfs enable/disable
int3472:
- Add support for GPIO type 0x02 (IR flood LED)
intel-speed-select: (updated to v1.26)
- Avoid using current base frequency as maximum
- Fix CPU extended family ID decoding
- Fix exit code
- Improve error reporting
intel/vsec:
- Refactor to support ACPI-enumerated PMT endpoints.
pcengines-apuv2:
- Attach software node to the gpiochip
uniwill:
- Refactor hwmon to smaller parts to accomodate HW diversity
- Support USB-C power/performance priority switch through sysfs
- Add another XMG Fusion 15 (L19) DMI vendor
- Enable fine-grained features to device lineup mapping
wmi:
- Perform output size check within WMI core to allow simpler WMI
drivers
misc:
- acpi_driver -> platform driver conversions (a large number of
changes from Rafael J. Wysocki)
- cleanups / refactoring / improvements"
* tag 'platform-drivers-x86-v7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (106 commits)
platform/x86: hp-wmi: Add support for Omen 16-wf1xxx (8C77)
platform/x86: hp-wmi: Add support for Omen 16-n0xxx (8A44)
platform/x86: hp-wmi: Add support for OMEN MAX 16-ak0xxx (8D87)
platform/x86: hp-wmi: fix fan table parsing
platform/x86: hp-wmi: add Omen 14-fb0xxx (board 8C58) support
platform/wmi: Replace .no_notify_data with .min_event_size
platform/wmi: Extend wmidev_query_block() to reject undersized data
platform/wmi: Extend wmidev_invoke_method() to reject undersized data
platform/wmi: Prepare to reject undersized unmarshalling results
platform/wmi: Convert drivers to use wmidev_invoke_procedure()
platform/wmi: Add wmidev_invoke_procedure()
platform/x86: int3472: Add support for GPIO type 0x02 (IR flood LED)
platform/x86: int3472: Parameterize LED con_id in registration
platform/x86: int3472: Rename pled to led in LED registration code
platform/x86: int3472: Use local variable for LED struct access
platform/x86: thinkpad_acpi: remove obsolete TODO comment
platform/x86: dell-wmi-sysman: bound enumeration string aggregation
platform/x86: hp-wmi: Ignore backlight and FnLock events
platform/x86: uniwill-laptop: Fix signedness bug
platform/x86: dell_rbu: avoid uninit value usage in packet_size_write()
...
Merge tag 'backlight-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Apple Backlight:
- Convert the Apple Backlight ACPI driver to a proper platform
driver, aligning with current ACPI binding practices
Skyworks SKY81452:
- Check the return value of `devm_gpiod_get_optional()`
to properly handle GPIO acquisition errors"
* tag 'backlight-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: apple_bl: Convert to a platform driver
backlight: sky81452-backlight: Check return value of devm_gpiod_get_optional() in sky81452_bl_parse_dt()
net: mctp: fix don't require received header reserved bits to be zero
From the MCTP Base specification (DSP0236 v1.2.1), the first byte of
the MCTP header contains a 4 bit reserved field, and 4 bit version.
On our current receive path, we require those 4 reserved bits to be
zero, but the 9500-8i card is non-conformant, and may set these
reserved bits.
DSP0236 states that the reserved bits must be written as zero, and
ignored when read. While the device might not conform to the former,
we should accept these message to conform to the latter.
Relax our check on the MCTP version byte to allow non-zero bits in the
reserved field.
David Carlier [Fri, 17 Apr 2026 05:54:08 +0000 (06:54 +0100)]
gtp: disable BH before calling udp_tunnel_xmit_skb()
gtp_genl_send_echo_req() runs as a generic netlink doit handler in
process context with BH not disabled. It calls udp_tunnel_xmit_skb(),
which eventually invokes iptunnel_xmit() — that uses __this_cpu_inc/dec
on softnet_data.xmit.recursion to track the tunnel xmit recursion level.
Without local_bh_disable(), the task may migrate between
dev_xmit_recursion_inc() and dev_xmit_recursion_dec(), breaking the
per-CPU counter pairing. The result is stale or negative recursion
levels that can later produce false-positive
SKB_DROP_REASON_RECURSION_LIMIT drops on either CPU.
The other udp_tunnel_xmit_skb() call sites in gtp.c are unaffected:
the data path runs under ndo_start_xmit and the echo response handlers
run from the UDP encap rx softirq, both with BH already disabled.
Fix it by disabling BH around the udp_tunnel_xmit_skb() call, mirroring
commit 2cd7e6971fc2 ("sctp: disable BH before calling
udp_tunnel_xmit_skb()").
Fixes: 6f1a9140ecda ("net: add xmit recursion limit to tunnel xmit functions") Cc: stable@vger.kernel.org Signed-off-by: David Carlier <devnexen@gmail.com> Link: https://patch.msgid.link/20260417055408.4667-1-devnexen@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dexuan Cui [Thu, 16 Apr 2026 19:14:33 +0000 (12:14 -0700)]
hv_sock: Report EOF instead of -EIO for FIN
Commit f0c5827d07cb unluckily causes a regression for the FIN packet,
and the final read syscall gets an error rather than 0.
Ideally, we would want to fix hvs_channel_readable_payload() so that it
could return 0 in the FIN scenario, but it's not good for the hv_sock
driver to use the VMBus ringbuffer's cached priv_read_index, which is
internal data in the VMBus driver.
Fix the regression in hv_sock by returning 0 rather than -EIO.
Fixes: f0c5827d07cb ("hv_sock: Return the readable bytes in hvs_stream_has_data()") Cc: stable@vger.kernel.org Reported-by: Ben Hillis <Ben.Hillis@microsoft.com> Reported-by: Mitchell Levy <levymitchell0@gmail.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Acked-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://patch.msgid.link/20260416191433.840637-1-decui@microsoft.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'leds-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
Core:
- Implement fallback to software node name for LED names
- Fix formatting issues in `led-core.c` reported by checkpatch.pl
- Make `led_remove_lookup()` NULL-aware
- Switch from `class_find_device_by_of_node()` to
`class_find_device_by_fwnode()`
- Drop the unneeded dependency on `OF_GPIO` from `LEDS_NETXBIG`
in Kconfig
Kinetic KTD2692:
- Make the `ktd2692_timing` variable static to resolve a
sparse warning
LGM SSO:
- Fix a typo in the `GET_SRC_OFFSET` macro
- Remove a duplicate assignment of `priv->mmap` in
`intel_sso_led_probe()`
Multicolor:
- Fix a signedness error by changing the `intensity_value` type
to `unsigned int`
Qualcomm LPG:
- Prevent array overflow when selecting high-resolution values
Spreadtrum SC2731:
- Add a compatible string for the SC2730 PMIC LED controller
TI LM3642:
- Use `guard(mutex)` to simplify locking and avoid manual
`mutex_unlock()` calls
TI LP5569:
- Use `sysfs_emit()` instead of `sprintf()` for sysfs outputs
TI LP5860:
- Add the `enable-gpios` property for the `VIO_EN` pin"
TI LP8860:
- Do not unconditionally program the EEPROM on probe
- Hold the mutex lock for the entirety of the EEPROM programming
process
- Return directly from `lp8860_init()` instead of using empty `goto`
statements
- Use a single regmap table and an access table instead of separate
maps for normal and EEPROM registers
- Remove an unused read of the `STATUS` register during EEPROM
programming
TTY Trigger:
- Prefer `IS_ERR_OR_NULL()` over manual NULL checks"
* tag 'leds-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds:
leds: class: Make led_remove_lookup() NULL-aware
leds: led-class: Switch to using class_find_device_by_fwnode()
leds: Kconfig: Drop unneeded dependency on OF_GPIO
leds: lm3642: Use guard to simplify locking
leds: core: Fix formatting issues
leds: core: Implement fallback to software node name for LED names
leds: lgm-sso: Fix typo in macro for src offset
dt-bindings: leds: lp5860: add enable-gpio
leds: Prefer IS_ERR_OR_NULL over manual NULL check
dt-bindings: leds: sc2731: Add compatible for SC2730
leds: lp8860: Do not always program EEPROM on probe
leds: lp8860: Remove unused read of STATUS register
leds: lp8860: Hold lock for all of EEPROM programming
leds: lp8860: Return directly from lp8860_init
leds: lp8860: Use a single regmap table
leds: lgm-sso: Remove duplicate assignments for priv->mmap
leds: qcom-lpg: Check for array overflow when selecting the high resolution
leds: ktd2692: Make ktd2692_timing variable static
leds: lp5569: Use sysfs_emit instead of sprintf()
leds: multicolor: Change intensity_value to unsigned int
Lorenzo Bianconi [Thu, 16 Apr 2026 10:30:12 +0000 (12:30 +0200)]
net: airoha: Fix possible TX queue stall in airoha_qdma_tx_napi_poll()
Since multiple net_device TX queues can share the same hw QDMA TX queue,
there is no guarantee we have inflight packets queued in hw belonging to a
net_device TX queue stopped in the xmit path because hw QDMA TX queue
can be full. In this corner case the net_device TX queue will never be
re-activated. In order to avoid any potential net_device TX queue stall,
we need to wake all the net_device TX queues feeding the same hw QDMA TX
queue in airoha_qdma_tx_napi_poll routine.
Weiming Shi [Thu, 16 Apr 2026 02:46:54 +0000 (19:46 -0700)]
openvswitch: cap upcall PID array size and pre-size vport replies
The vport netlink reply helpers allocate a fixed-size skb with
nlmsg_new(NLMSG_DEFAULT_SIZE, ...) but serialize the full upcall PID
array via ovs_vport_get_upcall_portids(). Since
ovs_vport_set_upcall_portids() accepts any non-zero multiple of
sizeof(u32) with no upper bound, a CAP_NET_ADMIN user can install a PID
array large enough to overflow the reply buffer, causing nla_put() to
fail with -EMSGSIZE and hitting BUG_ON(err < 0). On systems with
unprivileged user namespaces enabled (e.g., Ubuntu default), this is
reachable via unshare -Urn since OVS vport mutation operations use
GENL_UNS_ADMIN_PERM.
Reject attempts to set more PIDs than nr_cpu_ids in
ovs_vport_set_upcall_portids(), and pre-compute the worst-case reply
size in ovs_vport_cmd_msg_size() based on that bound, similar to the
existing ovs_dp_cmd_msg_size(). nr_cpu_ids matches the cap already
used by the per-CPU dispatch configuration on the datapath side
(ovs_dp_cmd_fill_info() serialises at most nr_cpu_ids PIDs), so the
two sides stay consistent.
Fixes: 5cd667b0a456 ("openvswitch: Allow each vport to have an array of 'port_id's.") Reported-by: Xiang Mei <xmei5@asu.edu> Assisted-by: Claude:claude-opus-4-6 Signed-off-by: Weiming Shi <bestswngs@gmail.com> Reviewed-by: Ilya Maximets <i.maximets@ovn.org> Link: https://patch.msgid.link/20260416024653.153456-2-bestswngs@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/mlx5: Fix HCA caps leak on notifier init failure
mlx5_mdev_init() allocates HCA caps via mlx5_hca_caps_alloc() before
calling mlx5_notifiers_init(). If notifier initialization fails, the
error path jumps to err_hca_caps and skips mlx5_hca_caps_free(), leaking
allocated caps.
Add a dedicated unwind label for notifier-init failure that frees HCA
caps before continuing the existing cleanup sequence.
Qingfang Deng [Wed, 15 Apr 2026 02:24:51 +0000 (10:24 +0800)]
pppoe: drop PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the current PPPoE driver assumes an
uncompressed (2-byte) protocol field. However, the generic PPP layer
function ppp_input() is not aware of the negotiation result, and still
accepts PFC frames.
If a peer with a broken implementation or an attacker sends a frame with
a compressed (1-byte) protocol field, the subsequent PPP payload is
shifted by one byte. This causes the network header to be 4-byte
misaligned, which may trigger unaligned access exceptions on some
architectures.
To reduce the attack surface, drop PPPoE PFC frames. Introduce
ppp_skb_is_compressed_proto() helper function to be used in both
ppp_generic.c and pppoe.c to avoid open-coding.
Fixes: 7fb1b8ca8fa1 ("ppp: Move PFC decompression to PPP generic layer") Signed-off-by: Qingfang Deng <qingfang.deng@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20260415022456.141758-2-qingfang.deng@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Qingfang Deng [Wed, 15 Apr 2026 02:24:50 +0000 (10:24 +0800)]
flow_dissector: do not dissect PPPoE PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the flow dissector driver has assumed an
uncompressed frame until the blamed commit.
During the review process of that commit [1], support for PFC is
suggested. However, having a compressed (1-byte) protocol field means
the subsequent PPP payload is shifted by one byte, causing 4-byte
misalignment for the network header and an unaligned access exception
on some architectures.
The exception can be reproduced by sending a PPPoE PFC frame to an
ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE
session is active on that interface:
Merge tag 'mfd-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core:
- Add a resource-managed version of alloc_workqueue()
(`devm_alloc_workqueue()`)
- Preserve the Open Firmware (OF) node when an ACPI handle
is present
Apple SMC:
- Wire up the Apple SMC power driver by adding a new MFD cell
Atmel HLCDC:
- Fetch the LVDS PLL clock as a fallback if the generic sys_clk
is unavailable
Broadcom BCM2835 PM:
- Add support for the BCM2712 power management device
- Introduce a hardware type identifier to distinguish SoC variants
Congatec CGBC, KEMPLD, RSMU, Si476x:
- Fix various kernel-doc warnings and correct struct member names
DLN2:
- Drop redundant USB device references and switch to managed
resource allocations
- Update bare 'unsigned' types to 'unsigned int'
ENE KB3930:
- Use the of_device_is_system_power_controller() wrapper
EZX PCAP:
- Avoid rescheduling after destroying the workqueue by switching
to a device-managed workqueue
- Drop redundant memory allocation error messages
- Return directly instead of using empty goto statements
Freescale i.MX25 TSADC:
- Convert devicetree bindings from TXT to YAML format
Freescale MC13xxx:
- Fix a memory leak in subdevice platform data allocation by
using devm_kmemdup()
Intel LPC ICH:
- Expose a software node for the GPIO controller cell to fix
GPIO lookups
Intel LPSS:
- Add PCI IDs for the Intel Nova Lake-H platform
Maxim MAX77620:
- Convert devicetree bindings from TXT to YAML format
- Document an optional I2C address for the MAX77663 RTC device
Maxim MAX77705:
- Make the max77705_pm_ops variable static to resolve a
sparse warning
MediaTek MT6397:
- Correct the hardware CIDs for the MT6328, MT6331, and MT6332
PMICs to allow proper driver binding
ROHM BD71828:
- Enable system wakeup via the power button
ROHM BD72720:
- Add a new compatible string for the ROHM BD73900 PMIC
SpacemiT P1:
- Drop the deprecated "vin-supply" property from the devicetree
bindings
- Add individual regulator supply properties to match actual
hardware topology
STMicroelectronics STPMIC1:
- Attempt system shutdown a second time to handle transient I2C
communication failures
Viperboard:
- Drop redundant USB device references"
* tag 'mfd-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (28 commits)
mfd: core: Preserve OF node when ACPI handle is present
mfd: ene-kb3930: Use of_device_is_system_power_controller() wrapper
mfd: intel-lpss: Add Intel Nova Lake-H PCI IDs
dt-bindings: mfd: max77620: Document optional RTC address for MAX77663
dt-bindings: mfd: max77620: Convert to DT schema
mfd: ezx-pcap: Avoid rescheduling after destroying workqueue
mfd: ezx-pcap: Return directly instead of empty gotos
mfd: ezx-pcap: Drop memory allocation error message
mfd: bcm2835-pm: Add BCM2712 PM device support
mfd: bcm2835-pm: Introduce SoC-specific type identifier
dt-bindings: mfd: bd72720: Add ROHM BD73900
mfd: si476x: Fix kernel-doc warnings
mfd: rsmu: Remove a empty kernel-doc line
mfd: kempld: Fix kernel-doc struct member names
mfd: congatec: Fix kernel-doc struct member names
dt-bindings: mfd: Convert fsl-imx25-tsadc.txt to yaml format
mfd: viperboard: Drop redundant device reference
mfd: dln2: Switch to managed resources and fix bare unsigned types
mfd: macsmc: Wire up Apple SMC power driver
mfd: mt6397: Properly fix CID of MT6328, MT6331 and MT6332
...
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"The usual collection of driver changes, more core infrastructure
updates that typical this cycle:
- Minor cleanups and kernel-doc fixes in bnxt_re, hns, rdmavt, efa,
ocrdma, erdma, rtrs, hfi1, ionic, and pvrdma
- New udata validation framework and driver updates
- Modernize CQ creation interface in mlx4 and mlx5, manage CQ umem in
core
- Promote UMEM to a core component, split out DMA block iterator
logic
- Introduce FRMR pools with aging, statistics, pinned handles, and
netlink control and use it in mlx5
- Add PCIe TLP emulation support in mlx5
- Extend umem to work with revocable pinned dmabuf's and use it in
irdma
- More net namespace improvements for rxe
- GEN4 hardware support in irdma
- First steps to MW and UC support in mana_ib
- Support for CQ umem and doorbells in bnxt_re
- Drop opa_vnic driver from hfi1
Fixes:
- IB/core zero dmac neighbor resolution race
- GID table memory free
- rxe pad/ICRC validation and r_key async errors
- mlx4 external umem for CQ
- umem DMA attributes on unmap
- mana_ib RX steering on RSS QP destroy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (116 commits)
RDMA/core: Fix user CQ creation for drivers without create_cq
RDMA/ionic: bound node_desc sysfs read with %.64s
IB/core: Fix zero dmac race in neighbor resolution
RDMA/mana_ib: Support memory windows
RDMA/rxe: Validate pad and ICRC before payload_size() in rxe_rcv
RDMA/core: Prefer NLA_NUL_STRING
RDMA/core: Fix memory free for GID table
RDMA/hns: Remove the duplicate calls to ib_copy_validate_udata_in()
RDMA: Remove redundant = {} for udata req structs
RDMA/irdma: Add missing comp_mask check in alloc_ucontext
RDMA/hns: Add missing comp_mask check in create_qp
RDMA/mlx5: Pull comp_mask validation into ib_copy_validate_udata_in_cm()
RDMA: Use ib_copy_validate_udata_in_cm() for zero comp_mask
RDMA/hns: Use ib_copy_validate_udata_in()
RDMA/mlx4: Use ib_copy_validate_udata_in() for QP
RDMA/mlx4: Use ib_copy_validate_udata_in()
RDMA/mlx5: Use ib_copy_validate_udata_in() for MW
RDMA/mlx5: Use ib_copy_validate_udata_in() for SRQ
RDMA/pvrdma: Use ib_copy_validate_udata_in() for srq
RDMA: Use ib_copy_validate_udata_in() for implicit full structs
...
Merge tag 'ntfs3_for_7.1' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"New:
- reject inodes with zero non-DOS link count
- return folios from ntfs_lock_new_page()
- subset of W=1 warnings for stricter checks
- work around -Wmaybe-uninitialized warnings
- buffer boundary checks to run_unpack()
- terminate the cached volume label after UTF-8 conversion
Fixes:
- check return value of indx_find to avoid infinite loop
- prevent uninitialized lcn caused by zero len
- increase CLIENT_REC name field size to prevent buffer overflow
- missing run load for vcn0 in attr_data_get_block_locked()
- memory leak in indx_create_allocate()
- OOB write in attr_wof_frame_info()
- mount failure on volumes with fragmented MFT bitmap
- integer overflow in run_unpack() volume boundary check
- validate rec->used in journal-replay file record check
Updates:
- resolve compare function in public index APIs
- $LXDEV xattr lookup
- potential double iput on d_make_root() failure
- initialize err in ni_allocate_da_blocks_locked()
- correct the pre_alloc condition in attr_allocate_clusters()"
* tag 'ntfs3_for_7.1' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: fix Smatch warnings
fs/ntfs3: validate rec->used in journal-replay file record check
fs/ntfs3: terminate the cached volume label after UTF-8 conversion
fs/ntfs3: fix potential double iput on d_make_root() failure
ntfs3: fix integer overflow in run_unpack() volume boundary check
ntfs3: add buffer boundary checks to run_unpack()
ntfs3: fix mount failure on volumes with fragmented MFT bitmap
fs/ntfs3: fix $LXDEV xattr lookup
ntfs3: fix OOB write in attr_wof_frame_info()
ntfs3: fix memory leak in indx_create_allocate()
ntfs3: work around false-postive -Wmaybe-uninitialized warnings
fs/ntfs3: fix missing run load for vcn0 in attr_data_get_block_locked()
fs/ntfs3: increase CLIENT_REC name field size
fs/ntfs3: prevent uninitialized lcn caused by zero len
fs/ntfs3: add a subset of W=1 warnings for stricter checks
fs/ntfs3: return folios from ntfs_lock_new_page()
fs/ntfs3: resolve compare function in public index APIs
ntfs3: reject inodes with zero non-DOS link count
Verify that the BPF verifier rejects a non-SCX struct_ops program
(tcp_congestion_ops) that attempts to call an SCX kfunc (scx_bpf_kick_cpu).
The test expects the load to fail with -EACCES from scx_kfunc_context_filter.
sched_ext: Deny SCX kfuncs to non-SCX struct_ops programs
scx_kfunc_context_filter() currently allows non-SCX struct_ops programs
(e.g. tcp_congestion_ops) to call SCX unlocked kfuncs. This is wrong
for two reasons:
- It is semantically incorrect: a TCP congestion control program has no
business calling SCX kfuncs such as scx_bpf_kick_cpu().
- With CONFIG_EXT_SUB_SCHED=y, kfuncs like scx_bpf_kick_cpu() call
scx_prog_sched(aux), which invokes bpf_prog_get_assoc_struct_ops(aux)
and casts the result to struct sched_ext_ops * before reading ops->priv.
For a non-SCX struct_ops program the returned pointer is the kdata of
that struct_ops type, which is far smaller than sched_ext_ops, making
the read an out-of-bounds access (confirmed with KASAN).
Extend the filter to cover scx_kfunc_set_any and scx_kfunc_set_idle as
well, and deny all SCX kfuncs for any struct_ops program that is not the
SCX struct_ops. This addresses both issues: the semantic contract is
enforced at the verifier level, and the runtime out-of-bounds access
becomes unreachable.
Kuba Piecuch [Mon, 20 Apr 2026 15:28:47 +0000 (15:28 +0000)]
sched_ext: Documentation: add note about multiple ops.enqueue() calls in a row
Commit 84b1a0ea0b7c
("sched_ext: Implement scx_bpf_dsq_reenq() for user DSQs")
introduced the possibility of ops.enqueue() being called multiple times
in a row for the same task without intervening calls to ops.dequeue().
Document this behavior as it may be surprising to some.
Acked-by: Andrea Righi <arighi@nvidia.com> Acked-by: Cheng-Yang Chou <yphbchou0911@gmail.com> Signed-off-by: Kuba Piecuch <jpiecuch@google.com> Signed-off-by: Tejun Heo <tj@kernel.org>
There's a bug in dm-thin in the function rebalance_children. If the
internal btree node has one entry, the code tries to copy all btree
entries from the node's child to the node itself and then decrement the
child's reference count.
If the child node is shared (it has reference count > 1), we won't free
it, so there would be two pointers to each of the grandchildren nodes.
But the reference counts of the grandchildren is not increased, thus the
reference count doesn't match the number of pointers that point to the
grandchildren. This results in "device mapper: space map common: unable
to decrement block" errors.
Fix this bug by incrementing reference counts on the grandchildren if the
btree node is shared.
Merge tag 'ecryptfs-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs updates from Tyler Hicks:
- avoid unnecessary eCryptfs inode timestamp truncation by re-using the
lower filesystem's time granularity
- various small code cleanups
- reorganize the setattr hook inode resizing to improve style and
readability, remove an unnecessary memory allocation when shrinking,
and to support an upcoming rework of the VFS interfaces involved in
truncation
* tag 'ecryptfs-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
ecryptfs: keep the lower iattr contained in truncate_upper
ecryptfs: factor out a ecryptfs_iattr_to_lower helper
ecryptfs: merge ecryptfs_inode_newsize_ok into truncate_upper
ecryptfs: combine the two ATTR_SIZE blocks in ecryptfs_setattr
ecryptfs: use ZERO_PAGE instead of allocating zeroed memory in truncate_upper
ecryptfs: streamline truncate_upper
ecryptfs: cleanup ecryptfs_setattr
ecryptfs: Drop TODO comment in ecryptfs_derive_iv
ecryptfs: Fix typo in ecryptfs_derive_iv function comment
ecryptfs: Log function name only once in decode_and_decrypt_filename
ecryptfs: Remove redundant if checks in encrypt_and_encode_filename
ecryptfs: Fix tag number in encrypt_filename() error message
ecryptfs: Use struct_size to improve process_response + send_miscdev
ecryptfs: Replace memcpy + manual NUL termination with strscpy
ecryptfs: Set s_time_gran to get correct time granularity
The counter width can be inferred from the compatible string, making the
explicit "sifive,fine-ctr-bits" property redundant. Remove the property
to simplify the bindings.
Merge tag 'nfsd-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd updates from Chuck Lever:
- filehandle signing to defend against filehandle-guessing attacks
(Benjamin Coddington)
The server now appends a SipHash-2-4 MAC to each filehandle when
the new "sign_fh" export option is enabled. NFSD then verifies
filehandles received from clients against the expected MAC;
mismatches return NFS error STALE
- convert the entire NLMv4 server-side XDR layer from hand-written C to
xdrgen-generated code, spanning roughly thirty patches (Chuck Lever)
XDR functions are generally boilerplate code and are easy to get
wrong. The goals of this conversion are improved memory safety, lower
maintenance burden, and groundwork for eventual Rust code generation
for these functions.
- improve pNFS block/SCSI layout robustness with two related changes
(Dai Ngo)
SCSI persistent reservation fencing is now tracked per client and
per device via an xarray, to avoid both redundant preempt operations
on devices already fenced and a potential NFSD deadlock when all nfsd
threads are waiting for a layout return.
- scalability and infrastructure improvements
Sincere thanks to all contributors, reviewers, testers, and bug
reporters who participated in the v7.1 NFSD development cycle.
* tag 'nfsd-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (83 commits)
NFSD: Docs: clean up pnfs server timeout docs
nfsd: fix comment typo in nfsxdr
nfsd: fix comment typo in nfs3xdr
NFSD: convert callback RPC program to per-net namespace
NFSD: use per-operation statidx for callback procedures
svcrdma: Use contiguous pages for RDMA Read sink buffers
SUNRPC: Add svc_rqst_page_release() helper
SUNRPC: xdr.h: fix all kernel-doc warnings
svcrdma: Factor out WR chain linking into helper
svcrdma: Add Write chunk WRs to the RPC's Send WR chain
svcrdma: Clean up use of rdma->sc_pd->device
svcrdma: Clean up use of rdma->sc_pd->device in Receive paths
svcrdma: Add fair queuing for Send Queue access
SUNRPC: Optimize rq_respages allocation in svc_alloc_arg
SUNRPC: Track consumed rq_pages entries
svcrdma: preserve rq_next_page in svc_rdma_save_io_pages
SUNRPC: Handle NULL entries in svc_rqst_release_pages
SUNRPC: Allocate a separate Reply page array
SUNRPC: Tighten bounds checking in svc_rqst_replace_page
NFSD: Sign filehandles
...
Mark Brown [Mon, 20 Apr 2026 17:40:07 +0000 (18:40 +0100)]
ASoC: Correct bug parsing DisCo booleans
Charles Keepax <ckeepax@opensource.cirrus.com> says:
MIPI DisCo uses the unfortunate convention of allowing boolean
properties to be present but having a zero value. Opposed to the
normal convention of simply not specifying the property. Fix an
issue in the SDCA code where mipi-sdca-control-deferrable is not
parsed correctly.
However, we also have some shipping ACPIs where these properties
are not specified correctly. Update the MBQ regmap to attempt defers
albeit with a warning in the case where a control attempts to defer
but is not marked at such. There is little down side to this as if
defer is genuinely not supported then the control will just return
the same error again.
Charles Keepax [Mon, 13 Apr 2026 12:46:21 +0000 (13:46 +0100)]
ASoC: SDCA: Fix reading of mipi-sdca-control-deferrable
The discussion in [1] highlighted that the SDCA code shouldn't be using
fwnode_property_read_bool() for DisCo controls, as the spec allows setting
the value to zero meaning the property should not be used. Correct a
small bug in the SDCA code that will mark such controls as deferrable.
Charles Keepax [Mon, 13 Apr 2026 12:46:20 +0000 (13:46 +0100)]
regmap: sdw-mbq: Allow defers on undeferrable controls
It is a fairly common DisCo issue to have the deferrability of controls
marked incorrectly and Windows seems very permissive in this regard. As
there isn't really any down side to trying a defer even if the control
isn't deferrable, allow this but add a warning message.
projects / thirdparty / linux.git / log
