drivers/i2c/Kconfig

   1 #
   2 # I2C subsystem configuration
   3 #
   4
   5 menu "I2C support"
   6
   7 config DM_I2C
   8         bool "Enable Driver Model for I2C drivers"
   9         depends on DM
  10         help
  11           Enable driver model for I2C. The I2C uclass interface: probe, read,
  12           write and speed, is implemented with the bus drivers operations,
  13           which provide methods for bus setting and data transfer. Each chip
  14           device (bus child) info is kept as parent platdata. The interface
  15           is defined in include/i2c.h. When i2c bus driver supports the i2c
  16           uclass, but the device drivers not, then DM_I2C_COMPAT config can
  17           be used as compatibility layer.
  18
  19 config DM_I2C_COMPAT
  20         bool "Enable I2C compatibility layer"
  21         depends on DM
  22         help
  23           Enable old-style I2C functions for compatibility with existing code.
  24           This option can be enabled as a temporary measure to avoid needing
  25           to convert all code for a board in a single commit. It should not
  26           be enabled for any board in an official release.
  27
  28 config I2C_CROS_EC_TUNNEL
  29         tristate "Chrome OS EC tunnel I2C bus"
  30         depends on CROS_EC
  31         help
  32           This provides an I2C bus that will tunnel i2c commands through to
  33           the other side of the Chrome OS EC to the I2C bus connected there.
  34           This will work whatever the interface used to talk to the EC (SPI,
  35           I2C or LPC). Some Chromebooks use this when the hardware design
  36           does not allow direct access to the main PMIC from the AP.
  37
  38 config I2C_CROS_EC_LDO
  39         bool "Provide access to LDOs on the Chrome OS EC"
  40         depends on CROS_EC
  41         ---help---
  42         On many Chromebooks the main PMIC is inaccessible to the AP. This is
  43         often dealt with by using an I2C pass-through interface provided by
  44         the EC. On some unfortunate models (e.g. Spring) the pass-through
  45         is not available, and an LDO message is available instead. This
  46         option enables a driver which provides very basic access to those
  47         regulators, via the EC. We implement this as an I2C bus which
  48         emulates just the TPS65090 messages we know about. This is done to
  49         avoid duplicating the logic in the TPS65090 regulator driver for
  50         enabling/disabling an LDO.
  51
  52 config I2C_SET_DEFAULT_BUS_NUM
  53         bool "Set default I2C bus number"
  54         depends on DM_I2C
  55         help
  56           Set default number of I2C bus to be accessed. This option provides
  57           behaviour similar to old (i.e. pre DM) I2C bus driver.
  58
  59 config I2C_DEFAULT_BUS_NUMBER
  60         hex "I2C default bus number"
  61         depends on I2C_SET_DEFAULT_BUS_NUM
  62         default 0x0
  63         help
  64           Number of default I2C bus to use
  65
  66 config DM_I2C_GPIO
  67         bool "Enable Driver Model for software emulated I2C bus driver"
  68         depends on DM_I2C && DM_GPIO
  69         help
  70           Enable the i2c bus driver emulation by using the GPIOs. The bus GPIO
  71           configuration is given by the device tree. Kernel-style device tree
  72           bindings are supported.
  73           Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
  74
  75 config SYS_I2C_AT91
  76         bool "Atmel I2C driver"
  77         depends on DM_I2C && ARCH_AT91
  78         help
  79           Add support for the Atmel I2C driver. A serious problem is that there
  80           is no documented way to issue repeated START conditions for more than
  81           two messages, as needed to support combined I2C messages. Use the
  82           i2c-gpio driver unless your system can cope with this limitation.
  83           Binding info: doc/device-tree-bindings/i2c/i2c-at91.txt
  84
  85 config SYS_I2C_FSL
  86        bool "Freescale I2C bus driver"
  87        depends on DM_I2C
  88        help
  89           Add support for Freescale I2C busses as used on MPC8240, MPC8245, and
  90           MPC85xx processors.
  91
  92 config SYS_I2C_CADENCE
  93         tristate "Cadence I2C Controller"
  94         depends on DM_I2C && (ARCH_ZYNQ || ARM64)
  95         help
  96           Say yes here to select Cadence I2C Host Controller. This controller is
  97           e.g. used by Xilinx Zynq.
  98
  99 config SYS_I2C_DW
 100         bool "Designware I2C Controller"
 101         default n
 102         help
 103           Say yes here to select the Designware I2C Host Controller. This
 104           controller is used in various SoCs, e.g. the ST SPEAr, Altera
 105           SoCFPGA, Synopsys ARC700 and some Intel x86 SoCs.
 106
 107 config SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
 108         bool "DW I2C Enable Status Register not supported"
 109         depends on SYS_I2C_DW && (TARGET_SPEAR300 || TARGET_SPEAR310 || \
 110                 TARGET_SPEAR320 || TARGET_SPEAR600 || TARGET_X600)
 111         default y
 112         help
 113           Some versions of the Designware I2C controller do not support the
 114           enable status register. This config option can be enabled in such
 115           cases.
 116
 117 config SYS_I2C_ASPEED
 118         bool "Aspeed I2C Controller"
 119         depends on DM_I2C && ARCH_ASPEED
 120         help
 121           Say yes here to select Aspeed I2C Host Controller. The driver
 122           supports AST2500 and AST2400 controllers, but is very limited.
 123           Only single master mode is supported and only byte-by-byte
 124           synchronous reads and writes are supported, no Pool Buffers or DMA.
 125
 126 config SYS_I2C_INTEL
 127         bool "Intel I2C/SMBUS driver"
 128         depends on DM_I2C
 129         help
 130           Add support for the Intel SMBUS driver. So far this driver is just
 131           a stub which perhaps some basic init. There is no implementation of
 132           the I2C API meaning that any I2C operations will immediately fail
 133           for now.
 134
 135 config SYS_I2C_IMX_LPI2C
 136         bool "NXP i.MX LPI2C driver"
 137         depends on ARCH_MX7ULP
 138         help
 139           Add support for the NXP i.MX LPI2C driver.
 140
 141 config SYS_I2C_MXC
 142         bool "NXP i.MX I2C driver"
 143         depends on MX6
 144         help
 145           Add support for the NXP i.MX I2C driver. This supports upto for bus
 146           channels and operating on standard mode upto 100 kbits/s and fast
 147           mode upto 400 kbits/s.
 148
 149 config SYS_I2C_ROCKCHIP
 150         bool "Rockchip I2C driver"
 151         depends on DM_I2C
 152         help
 153           Add support for the Rockchip I2C driver. This is used with various
 154           Rockchip parts such as RK3126, RK3128, RK3036 and RK3288. All chips
 155           have several I2C ports and all are provided, controled by the
 156           device tree.
 157
 158 config SYS_I2C_SANDBOX
 159         bool "Sandbox I2C driver"
 160         depends on SANDBOX && DM_I2C
 161         help
 162           Enable I2C support for sandbox. This is an emulation of a real I2C
 163           bus. Devices can be attached to the bus using the device tree
 164           which specifies the driver to use.  See sandbox.dts as an example.
 165
 166 config SYS_I2C_S3C24X0
 167         bool "Samsung I2C driver"
 168         depends on ARCH_EXYNOS4 && DM_I2C
 169         help
 170           Support for Samsung I2C controller as Samsung SoCs.
 171
 172 config SYS_I2C_UNIPHIER
 173         bool "UniPhier I2C driver"
 174         depends on ARCH_UNIPHIER && DM_I2C
 175         default y
 176         help
 177           Support for UniPhier I2C controller driver.  This I2C controller
 178           is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
 179
 180 config SYS_I2C_UNIPHIER_F
 181         bool "UniPhier FIFO-builtin I2C driver"
 182         depends on ARCH_UNIPHIER && DM_I2C
 183         default y
 184         help
 185           Support for UniPhier FIFO-builtin I2C controller driver.
 186           This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
 187
 188 config SYS_I2C_MVTWSI
 189         bool "Marvell I2C driver"
 190         depends on DM_I2C
 191         help
 192           Support for Marvell I2C controllers as used on the orion5x and
 193           kirkwood SoC families.
 194
 195 config TEGRA186_BPMP_I2C
 196         bool "Enable Tegra186 BPMP-based I2C driver"
 197         depends on TEGRA186_BPMP
 198         help
 199           Support for Tegra I2C controllers managed by the BPMP (Boot and
 200           Power Management Processor). On Tegra186, some I2C controllers are
 201           directly controlled by the main CPU, whereas others are controlled
 202           by the BPMP, and can only be accessed by the main CPU via IPC
 203           requests to the BPMP. This driver covers the latter case.
 204
 205 source "drivers/i2c/muxes/Kconfig"
 206
 207 endmenu