include/configs/M5282EVB.h

   1 /*
   2  * Configuation settings for the Motorola MC5282EVB board.
   3  *
   4  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * board/config.h - configuration options, board specific
  11  */
  12
  13 #ifndef _CONFIG_M5282EVB_H
  14 #define _CONFIG_M5282EVB_H
  15
  16 /*
  17  * High Level Configuration Options
  18  * (easy to change)
  19  */
  20 #define CONFIG_MCFTMR
  21
  22 #define CONFIG_MCFUART
  23 #define CONFIG_SYS_UART_PORT            (0)
  24
  25 #undef  CONFIG_MONITOR_IS_IN_RAM        /* define if monitor is started from a pre-loader */
  26
  27 /* Configuration for environment
  28  * Environment is embedded in u-boot in the second sector of the flash
  29  */
  30 #define CONFIG_ENV_ADDR         0xffe04000
  31 #define CONFIG_ENV_SIZE         0x2000
  32
  33 #define LDS_BOARD_TEXT \
  34         . = DEFINED(env_offset) ? env_offset : .; \
  35         env/embedded.o(.text*);
  36
  37 /*
  38  * BOOTP options
  39  */
  40 #define CONFIG_BOOTP_BOOTFILESIZE
  41 #define CONFIG_BOOTP_BOOTPATH
  42 #define CONFIG_BOOTP_GATEWAY
  43 #define CONFIG_BOOTP_HOSTNAME
  44
  45 /*
  46  * Command line configuration.
  47  */
  48
  49 #define CONFIG_MCFFEC
  50 #ifdef CONFIG_MCFFEC
  51 #       define CONFIG_MII               1
  52 #       define CONFIG_MII_INIT          1
  53 #       define CONFIG_SYS_DISCOVER_PHY
  54 #       define CONFIG_SYS_RX_ETH_BUFFER 8
  55 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  56
  57 #       define CONFIG_SYS_FEC0_PINMUX           0
  58 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  59 #       define MCFFEC_TOUT_LOOP         50000
  60 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  61 #       ifndef CONFIG_SYS_DISCOVER_PHY
  62 #               define FECDUPLEX        FULL
  63 #               define FECSPEED         _100BASET
  64 #       else
  65 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  66 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  67 #               endif
  68 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
  69 #endif
  70
  71 #ifdef CONFIG_MCFFEC
  72 #       define CONFIG_IPADDR    192.162.1.2
  73 #       define CONFIG_NETMASK   255.255.255.0
  74 #       define CONFIG_SERVERIP  192.162.1.1
  75 #       define CONFIG_GATEWAYIP 192.162.1.1
  76 #endif                          /* CONFIG_MCFFEC */
  77
  78 #define CONFIG_HOSTNAME         M5282EVB
  79 #define CONFIG_EXTRA_ENV_SETTINGS               \
  80         "netdev=eth0\0"                         \
  81         "loadaddr=10000\0"                      \
  82         "u-boot=u-boot.bin\0"                   \
  83         "load=tftp ${loadaddr) ${u-boot}\0"     \
  84         "upd=run load; run prog\0"              \
  85         "prog=prot off ffe00000 ffe3ffff;"      \
  86         "era ffe00000 ffe3ffff;"                \
  87         "cp.b ${loadaddr} ffe00000 ${filesize};"\
  88         "save\0"                                \
  89         ""
  90
  91 #define CONFIG_SYS_LONGHELP             /* undef to save memory         */
  92
  93 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
  94
  95 #define CONFIG_SYS_LOAD_ADDR            0x20000
  96
  97 #define CONFIG_SYS_MEMTEST_START        0x400
  98 #define CONFIG_SYS_MEMTEST_END          0x380000
  99
 100 #define CONFIG_SYS_CLK                  64000000
 101
 102 /* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
 103
 104 #define CONFIG_SYS_MFD                  0x02    /* PLL Multiplication Factor Devider */
 105 #define CONFIG_SYS_RFD                  0x00    /* PLL Reduce Frecuency Devider */
 106
 107 /*
 108  * Low Level Configuration Settings
 109  * (address mappings, register initial values, etc.)
 110  * You should know what you are doing if you make changes here.
 111  */
 112 #define CONFIG_SYS_MBAR         0x40000000
 113
 114 /*-----------------------------------------------------------------------
 115  * Definitions for initial stack pointer and data area (in DPRAM)
 116  */
 117 #define CONFIG_SYS_INIT_RAM_ADDR        0x20000000
 118 #define CONFIG_SYS_INIT_RAM_SIZE        0x10000 /* Size of used area in internal SRAM    */
 119 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 120 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 121
 122 /*-----------------------------------------------------------------------
 123  * Start addresses for the final memory configuration
 124  * (Set up by the startup code)
 125  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 126  */
 127 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 128 #define CONFIG_SYS_SDRAM_SIZE           16      /* SDRAM size in MB */
 129 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_CS0_BASE
 130 #define CONFIG_SYS_INT_FLASH_BASE       0xf0000000
 131 #define CONFIG_SYS_INT_FLASH_ENABLE     0x21
 132
 133 /* If M5282 port is fully implemented the monitor base will be behind
 134  * the vector table. */
 135 #if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
 136 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 137 #else
 138 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418)  /* 24 Byte for CFM-Config */
 139 #endif
 140
 141 #define CONFIG_SYS_MONITOR_LEN          0x20000
 142 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 143 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 144
 145 /*
 146  * For booting Linux, the board info and command line data
 147  * have to be in the first 8 MB of memory, since this is
 148  * the maximum mapped by the Linux kernel during initialization ??
 149  */
 150 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 151
 152 /*-----------------------------------------------------------------------
 153  * FLASH organization
 154  */
 155 #define CONFIG_SYS_FLASH_CFI
 156 #ifdef CONFIG_SYS_FLASH_CFI
 157
 158 #       define CONFIG_FLASH_CFI_DRIVER  1
 159 #       define CONFIG_SYS_FLASH_SIZE            0x1000000       /* Max size that the board might have */
 160 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 161 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 162 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 163 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 164 #       define CONFIG_SYS_FLASH_CHECKSUM
 165 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_FLASH_BASE }
 166 #endif
 167
 168 /*-----------------------------------------------------------------------
 169  * Cache Configuration
 170  */
 171 #define CONFIG_SYS_CACHELINE_SIZE       16
 172
 173 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 174                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 175 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 176                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 177 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_CINV + CF_CACR_DCM)
 178 #define CONFIG_SYS_CACHE_ACR0           (CONFIG_SYS_SDRAM_BASE | \
 179                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 180                                          CF_ACR_EN | CF_ACR_SM_ALL)
 181 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_CENB | CF_CACR_DISD | \
 182                                          CF_CACR_CEIB | CF_CACR_DBWE | \
 183                                          CF_CACR_EUSP)
 184
 185 /*-----------------------------------------------------------------------
 186  * Memory bank definitions
 187  */
 188 #define CONFIG_SYS_CS0_BASE             0xFFE00000
 189 #define CONFIG_SYS_CS0_CTRL             0x00001980
 190 #define CONFIG_SYS_CS0_MASK             0x001F0001
 191
 192 /*-----------------------------------------------------------------------
 193  * Port configuration
 194  */
 195 #define CONFIG_SYS_PACNT                0x0000000       /* Port A D[31:24] */
 196 #define CONFIG_SYS_PADDR                0x0000000
 197 #define CONFIG_SYS_PADAT                0x0000000
 198
 199 #define CONFIG_SYS_PBCNT                0x0000000       /* Port B D[23:16] */
 200 #define CONFIG_SYS_PBDDR                0x0000000
 201 #define CONFIG_SYS_PBDAT                0x0000000
 202
 203 #define CONFIG_SYS_PCCNT                0x0000000       /* Port C D[15:08] */
 204 #define CONFIG_SYS_PCDDR                0x0000000
 205 #define CONFIG_SYS_PCDAT                0x0000000
 206
 207 #define CONFIG_SYS_PDCNT                0x0000000       /* Port D D[07:00] */
 208 #define CONFIG_SYS_PCDDR                0x0000000
 209 #define CONFIG_SYS_PCDAT                0x0000000
 210
 211 #define CONFIG_SYS_PEHLPAR              0xC0
 212 #define CONFIG_SYS_PUAPAR               0x0F    /* UA0..UA3 = Uart 0 +1 */
 213 #define CONFIG_SYS_DDRUA                0x05
 214 #define CONFIG_SYS_PJPAR                0xFF
 215
 216 #endif                          /* _CONFIG_M5282EVB_H */