include/configs/ti_armv7_common.h

   1 /*
   2  * ti_armv7_common.h
   3  *
   4  * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  *
   8  * The various ARMv7 SoCs from TI all share a number of IP blocks when
   9  * implementing a given feature.  Rather than define these in every
  10  * board or even SoC common file, we define a common file to be re-used
  11  * in all cases.  While technically true that some of these details are
  12  * configurable at the board design, they are common throughout SoC
  13  * reference platforms as well as custom designs and become de facto
  14  * standards.
  15  */
  16
  17 #ifndef __CONFIG_TI_ARMV7_COMMON_H__
  18 #define __CONFIG_TI_ARMV7_COMMON_H__
  19
  20 /* Common define for many platforms. */
  21 #define CONFIG_OMAP
  22 #define CONFIG_OMAP_COMMON
  23
  24 /*
  25  * We typically do not contain NOR flash.  In the cases where we do, we
  26  * undefine this later.
  27  */
  28 #define CONFIG_SYS_NO_FLASH
  29
  30 /* Support both device trees and ATAGs. */
  31 #define CONFIG_OF_LIBFDT
  32 #define CONFIG_CMDLINE_TAG
  33 #define CONFIG_SETUP_MEMORY_TAGS
  34 #define CONFIG_INITRD_TAG
  35
  36 /*
  37  * Our DDR memory always starts at 0x80000000 and U-Boot shall have
  38  * relocated itself to higher in memory by the time this value is used.
  39  */
  40 #define CONFIG_SYS_LOAD_ADDR            0x80000000
  41
  42 /*
  43  * Default to a quick boot delay.
  44  */
  45 #define CONFIG_BOOTDELAY                1
  46
  47 /*
  48  * DDR information.  We say (for simplicity) that we have 1 bank,
  49  * always, even when we have more.  We always start at 0x80000000,
  50  * and we place the initial stack pointer in our SRAM.
  51  */
  52 #define CONFIG_NR_DRAM_BANKS            1
  53 #define CONFIG_SYS_SDRAM_BASE           0x80000000
  54 #define CONFIG_SYS_INIT_SP_ADDR         (NON_SECURE_SRAM_END - \
  55                                                 GENERATED_GBL_DATA_SIZE)
  56
  57 /* Timer information. */
  58 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
  59
  60 /* I2C IP block */
  61 #define CONFIG_I2C
  62 #define CONFIG_HARD_I2C
  63 #define CONFIG_SYS_I2C_SPEED            100000
  64 #define CONFIG_SYS_I2C_SLAVE            1
  65 #define CONFIG_I2C_MULTI_BUS
  66 #define CONFIG_DRIVER_OMAP24XX_I2C
  67 #define CONFIG_CMD_I2C
  68
  69 /* MMC/SD IP block */
  70 #define CONFIG_MMC
  71 #define CONFIG_GENERIC_MMC
  72 #define CONFIG_OMAP_HSMMC
  73 #define CONFIG_CMD_MMC
  74
  75 /* McSPI IP block */
  76 #define CONFIG_SPI
  77 #define CONFIG_OMAP3_SPI
  78 #define CONFIG_CMD_SPI
  79
  80 /* GPIO block */
  81 #define CONFIG_OMAP_GPIO
  82 #define CONFIG_CMD_GPIO
  83
  84 /*
  85  * GPMC NAND block.  We support 1 device and the physical address to
  86  * access CS0 at is 0x8000000.
  87  */
  88 #ifdef CONFIG_NAND
  89 #define CONFIG_NAND_OMAP_GPMC
  90 #define CONFIG_SYS_NAND_BASE            0x8000000
  91 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  92 #define CONFIG_CMD_NAND
  93 #endif
  94
  95 /*
  96  * The following are general good-enough settings for U-Boot.  We set a
  97  * large malloc pool as we generally have a lot of DDR, and we opt for
  98  * function over binary size in the main portion of U-Boot as this is
  99  * generally easily constrained later if needed.  We enable the config
 100  * options that give us information in the environment about what board
 101  * we are on so we do not need to rely on the command prompt.  We set a
 102  * console baudrate of 115200 and use the default baud rate table.
 103  */
 104 #define CONFIG_SYS_MALLOC_LEN           (1024 << 10)
 105 #define CONFIG_SYS_HUSH_PARSER
 106 #define CONFIG_SYS_PROMPT               "U-Boot# "
 107 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 108 #define CONFIG_BAUDRATE                 115200
 109 #define CONFIG_ENV_VARS_UBOOT_CONFIG    /* Strongly encouraged */
 110 #define CONFIG_ENV_OVERWRITE            /* Overwrite ethaddr / serial# */
 111
 112 /* As stated above, the following choices are optional. */
 113 #define CONFIG_SYS_LONGHELP
 114 #define CONFIG_AUTO_COMPLETE
 115 #define CONFIG_CMDLINE_EDITING
 116 #define CONFIG_VERSION_VARIABLE
 117
 118 /* We set the max number of command args high to avoid HUSH bugs. */
 119 #define CONFIG_SYS_MAXARGS              64
 120
 121 /* Console I/O Buffer Size */
 122 #define CONFIG_SYS_CBSIZE               512
 123 /* Print Buffer Size */
 124 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE \
 125                                         + sizeof(CONFIG_SYS_PROMPT) + 16)
 126 /* Boot Argument Buffer Size */
 127 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 128
 129 /*
 130  * When we have SPI, NOR or NAND flash we expect to be making use of
 131  * mtdparts, both for ease of use in U-Boot and for passing information
 132  * on to the Linux kernel.
 133  */
 134 #if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND)
 135 #define CONFIG_MTD_DEVICE               /* Required for mtdparts */
 136 #define CONFIG_CMD_MTDPARTS
 137 #endif
 138
 139 /*
 140  * For commands to use, we take the default list and add a few other
 141  * useful commands.  Note that we must have set CONFIG_SYS_NO_FLASH
 142  * prior to this include, in order to skip a few commands.  When we do
 143  * have flash, if we expect these commands they must be enabled in that
 144  * config.  If desired, a specific list of desired commands can be used
 145  * instead.
 146  */
 147 #include <config_cmd_default.h>
 148 #define CONFIG_CMD_ASKENV
 149 #define CONFIG_CMD_ECHO
 150 #define CONFIG_CMD_BOOTZ
 151
 152 /*
 153  * Common filesystems support.  When we have removable storage we
 154  * enabled a number of useful commands and support.
 155  */
 156 #if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
 157 #define CONFIG_DOS_PARTITION
 158 #define CONFIG_CMD_FAT
 159 #define CONFIG_FAT_WRITE
 160 #define CONFIG_CMD_EXT2
 161 #define CONFIG_CMD_EXT4
 162 #define CONFIG_CMD_FS_GENERIC
 163 #endif
 164
 165 /*
 166  * Our platforms make use of SPL to initalize the hardware (primarily
 167  * memory) enough for full U-Boot to be loaded.  We also support Falcon
 168  * Mode so that the Linux kernel can be booted directly from SPL
 169  * instead, if desired.  We make use of the general SPL framework found
 170  * under common/spl/.  Given our generally common memory map, we set a
 171  * number of related defaults and sizes here.
 172  */
 173 #ifndef CONFIG_NOR_BOOT
 174 #define CONFIG_SPL
 175 #define CONFIG_SPL_FRAMEWORK
 176 #define CONFIG_SPL_OS_BOOT
 177
 178 /*
 179  * Place the image at the start of the ROM defined image space.
 180  * We limit our size to the ROM-defined downloaded image area, and use the
 181  * rest of the space for stack.  We load U-Boot itself into memory at
 182  * 0x80800000 for legacy reasons (to not conflict with older SPLs).  We
 183  * have our BSS be placed 1MiB after this, to allow for the default
 184  * Linux kernel address of 0x80008000 to work, in the Falcon Mode case.
 185  * We have the SPL malloc pool at the end of the BSS area.
 186  */
 187 #define CONFIG_SPL_STACK                CONFIG_SYS_INIT_SP_ADDR
 188 #define CONFIG_SYS_TEXT_BASE            0x80800000
 189 #define CONFIG_SPL_BSS_START_ADDR       0x80a00000
 190 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000         /* 512 KB */
 191 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
 192                                          CONFIG_SPL_BSS_MAX_SIZE)
 193 #define CONFIG_SYS_SPL_MALLOC_SIZE      CONFIG_SYS_MALLOC_LEN
 194
 195 /* RAW SD card / eMMC locations. */
 196 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
 197 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
 198
 199 /* FAT sd card locations. */
 200 #define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION    1
 201 #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME        "u-boot.img"
 202
 203 #ifdef CONFIG_SPL_OS_BOOT
 204 #define CONFIG_SYS_SPL_ARGS_ADDR                0x80F80000
 205
 206 /* FAT */
 207 #define CONFIG_SPL_FAT_LOAD_KERNEL_NAME         "uImage"
 208 #define CONFIG_SPL_FAT_LOAD_ARGS_NAME           "args"
 209
 210 /* RAW SD card / eMMC */
 211 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900   /* address 0x120000 */
 212 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x80    /* address 0x10000 */
 213 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0x80    /* 64KiB */
 214
 215 /* NAND */
 216 #ifdef CONFIG_NAND
 217 #define CONFIG_CMD_SPL_NAND_OFS                 0x240000 /* end of u-boot */
 218 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS         0x280000
 219 #define CONFIG_CMD_SPL_WRITE_SIZE               0x2000
 220 #endif
 221
 222 /* spl export command */
 223 #define CONFIG_CMD_SPL
 224 #endif
 225
 226 #ifdef CONFIG_MMC
 227 #define CONFIG_SPL_LIBDISK_SUPPORT
 228 #define CONFIG_SPL_MMC_SUPPORT
 229 #define CONFIG_SPL_FAT_SUPPORT
 230 #endif
 231
 232 /* General parts of the framework, required. */
 233 #define CONFIG_SPL_I2C_SUPPORT
 234 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 235 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 236 #define CONFIG_SPL_SERIAL_SUPPORT
 237 #define CONFIG_SPL_GPIO_SUPPORT
 238 #define CONFIG_SPL_BOARD_INIT
 239
 240 #ifdef CONFIG_NAND
 241 #define CONFIG_SPL_NAND_AM33XX_BCH      /* OMAP4 and later ELM support */
 242 #define CONFIG_SPL_NAND_SUPPORT
 243 #define CONFIG_SPL_NAND_BASE
 244 #define CONFIG_SPL_NAND_DRIVERS
 245 #define CONFIG_SPL_NAND_ECC
 246 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 247 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 248 #endif
 249 #endif /* !CONFIG_NOR_BOOT */
 250
 251 #endif  /* __CONFIG_TI_ARMV7_COMMON_H__ */