#include <common.h>
-#ifdef CONFIG_USE_IRQ
-void do_irq (struct pt_regs *pt_regs)
-{
-}
-#endif
-
#if defined(CONFIG_TEGRA)
static ulong timestamp;
static ulong lastdec;
extra-y = start.o
obj-y += cpu.o
-obj-$(CONFIG_USE_IRQ) += interrupts.o
obj-$(CONFIG_EP93XX) += ep93xx/
obj-$(CONFIG_IMX) += imx/
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_USE_IRQ) += interrupts.o
obj-$(CONFIG_DISPLAY_CPUINFO) += cpu_info.o
obj-y += speed.o
obj-y += timer.o
#include <asm/system.h>
#include <asm/io.h>
-#ifdef CONFIG_USE_IRQ
-DECLARE_GLOBAL_DATA_PTR;
-#endif
-
static void cache_flush(void);
int cleanup_before_linux (void)
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_USE_IRQ
-int interrupt_init (void)
-{
- unsigned long cpsr;
-
- /*
- * setup up stacks if necessary
- */
- IRQ_STACK_START = gd->irq_sp - 4;
- IRQ_STACK_START_IN = gd->irq_sp + 8;
- FIQ_STACK_START = IRQ_STACK_START - CONFIG_STACKSIZE_IRQ;
-
-
- __asm__ __volatile__("mrs %0, cpsr\n"
- : "=r" (cpsr)
- :
- : "memory");
-
- __asm__ __volatile__("msr cpsr_c, %0\n"
- "mov sp, %1\n"
- :
- : "r" (IRQ_MODE | I_BIT | F_BIT | (cpsr & ~FIQ_MODE)),
- "r" (IRQ_STACK_START)
- : "memory");
-
- __asm__ __volatile__("msr cpsr_c, %0\n"
- "mov sp, %1\n"
- :
- : "r" (FIQ_MODE | I_BIT | F_BIT | (cpsr & ~IRQ_MODE)),
- "r" (FIQ_STACK_START)
- : "memory");
-
- __asm__ __volatile__("msr cpsr_c, %0"
- :
- : "r" (cpsr)
- : "memory");
-
- return arch_interrupt_init();
-}
-
-/* enable IRQ interrupts */
-void enable_interrupts (void)
-{
- unsigned long temp;
- __asm__ __volatile__("mrs %0, cpsr\n"
- "bic %0, %0, #0x80\n"
- "msr cpsr_c, %0"
- : "=r" (temp)
- :
- : "memory");
-}
-
-
-/*
- * disable IRQ/FIQ interrupts
- * returns true if interrupts had been enabled before we disabled them
- */
-int disable_interrupts (void)
-{
- unsigned long old,temp;
- __asm__ __volatile__("mrs %0, cpsr\n"
- "orr %1, %0, #0xc0\n"
- "msr cpsr_c, %1"
- : "=r" (old), "=r" (temp)
- :
- : "memory");
- return (old & 0x80) == 0;
-}
-#else
int interrupt_init (void)
{
/*
{
return 0;
}
-#endif
-
void bad_mode (void)
{
bad_mode ();
}
-#ifndef CONFIG_USE_IRQ
void do_irq (struct pt_regs *pt_regs)
{
efi_restore_gd();
show_regs (pt_regs);
bad_mode ();
}
-#endif
gd->irq_sp = gd->start_addr_sp;
# if !defined(CONFIG_ARM64)
-# ifdef CONFIG_USE_IRQ
- gd->start_addr_sp -= (CONFIG_STACKSIZE_IRQ + CONFIG_STACKSIZE_FIQ);
- debug("Reserving %zu Bytes for IRQ stack at: %08lx\n",
- CONFIG_STACKSIZE_IRQ + CONFIG_STACKSIZE_FIQ, gd->start_addr_sp);
-
- /* 8-byte alignment for ARM ABI compliance */
- gd->start_addr_sp &= ~0x07;
-# endif
/* leave 3 words for abort-stack, plus 1 for alignment */
gd->start_addr_sp -= 16;
# endif
IRQ_STACK_START_IN:
.word 0x0badc0de
-#ifdef CONFIG_USE_IRQ
-/* IRQ stack memory (calculated at run-time) */
-.globl IRQ_STACK_START
-IRQ_STACK_START:
- .word 0x0badc0de
-
-/* IRQ stack memory (calculated at run-time) */
-.globl FIQ_STACK_START
-FIQ_STACK_START:
- .word 0x0badc0de
-
-#endif /* CONFIG_USE_IRQ */
-
@
@ IRQ stack frame.
@
bad_save_user_regs
bl do_not_used
-#ifdef CONFIG_USE_IRQ
-
- .align 5
-irq:
- get_irq_stack
- irq_save_user_regs
- bl do_irq
- irq_restore_user_regs
-
- .align 5
-fiq:
- get_fiq_stack
- /* someone ought to write a more effiction fiq_save_user_regs */
- irq_save_user_regs
- bl do_fiq
- irq_restore_user_regs
-
-#else
.align 5
irq:
bad_save_user_regs
bl do_fiq
-#endif /* CONFIG_USE_IRQ */
-
#endif /* CONFIG_SPL_BUILD */
#endif /* CONFIG_DRIVER_TI_EMAC */
#if defined(CONFIG_SOC_DA8XX)
-#ifndef CONFIG_USE_IRQ
void irq_init(void)
{
/*
writel(0xffffffff, &davinci_aintc_regs->ecr2);
writel(0xffffffff, &davinci_aintc_regs->ecr3);
}
-#endif
/*
* Enable PSC for various peripherals.
DECLARE_GLOBAL_DATA_PTR;
#define DDR_MIN_ADDR CONFIG_SYS_SDRAM_BASE
+#define STACKSIZE (512 << 10) /* 512 KiB */
#define DDR_REMAP_ADDR 0x80000000
#define ECC_START_ADDR1 ((DDR_MIN_ADDR - DDR_REMAP_ADDR) >> 17)
#define ECC_END_ADDR1 (((gd->start_addr_sp - DDR_REMAP_ADDR - \
- CONFIG_STACKSIZE) >> 17) - 2)
+ STACKSIZE) >> 17) - 2)
#define DDR_TEST_BURST_SIZE 1024
DECLARE_GLOBAL_DATA_PTR;
+#define STACKSIZE 2048
+
static const char * const cpu_modes[8] = {
"Application", "Supervisor", "Interrupt level 0", "Interrupt level 1",
"Interrupt level 2", "Interrupt level 3", "Exception", "NMI"
printf("CPU Mode: %s\n", cpu_modes[mode]);
/* Avoid exception loops */
- if (regs->sp < (gd->start_addr_sp - CONFIG_STACKSIZE) ||
+ if (regs->sp < (gd->start_addr_sp - STACKSIZE) ||
regs->sp >= gd->start_addr_sp)
printf("\nStack pointer seems bogus, won't do stack dump\n");
else
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-#ifdef CONFIG_USE_IRQ
-/* IRQ stack memory (calculated at run-time) */
-.globl IRQ_STACK_START
-IRQ_STACK_START:
- .word 0x0badc0de
-
-/* IRQ stack memory (calculated at run-time) */
-.globl FIQ_STACK_START
-FIQ_STACK_START:
- .word 0x0badc0de
-#endif
-
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
int board_init(void)
{
-#ifndef CONFIG_USE_IRQ
irq_init();
-#endif
/* arch number of the board */
gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;
int board_init(void)
{
-#ifndef CONFIG_USE_IRQ
irq_init();
-#endif
#ifdef CONFIG_NAND_DAVINCI
/*
int board_init(void)
{
-#ifndef CONFIG_USE_IRQ
irq_init();
-#endif
/* arch number of the board */
gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_LCDK;
/* Set LCD_B_PWR low to power down LCD Backlight*/
gpio_direction_output(102, 0);
-#ifndef CONFIG_USE_IRQ
irq_init();
-#endif
/*
* NAND CS setup - cycle counts based on da850evm NAND timings in the
int board_init(void)
{
-#ifndef CONFIG_USE_IRQ
irq_init();
-#endif
/* arch number of the board */
/* LEGO didn't register for a unique number and uses da850evm */
{
int val;
-#ifndef CONFIG_USE_IRQ
irq_init();
-#endif
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
text_base, bss_start, bss_end);
#endif
-#ifdef CONFIG_USE_IRQ
- debug("IRQ Stack: %08lx\n", IRQ_STACK_START);
- debug("FIQ Stack: %08lx\n", FIQ_STACK_START);
-#endif
-
return 0;
}
u8 eir_reg;
u8 pkt_cnt;
-#ifdef CONFIG_USE_IRQ
- /* clear global interrupt enable bit in enc28j60 */
- enc_bclr(enc, CTL_REG_EIE, ENC_EIE_INTIE);
-#endif
(void)enc_r8(enc, CTL_REG_ESTAT);
eir_reg = enc_r8(enc, CTL_REG_EIR);
if (eir_reg & ENC_EIR_TXIF) {
printf("%s: tx error\n", enc->dev->name);
enc_bclr(enc, CTL_REG_EIR, ENC_EIR_TXERIF);
}
-#ifdef CONFIG_USE_IRQ
- /* set global interrupt enable bit in enc28j60 */
- enc_bset(enc, CTL_REG_EIE, ENC_EIE_INTIE);
-#endif
}
/*
/* Reset PDPXMD-bit => half duplex */
enc_phy_write(enc, PHY_REG_PHCON1, 0);
-#ifdef CONFIG_USE_IRQ
- /* enable interrupts */
- enc_bset(enc, CTL_REG_EIE, ENC_EIE_PKTIE);
- enc_bset(enc, CTL_REG_EIE, ENC_EIE_TXIE);
- enc_bset(enc, CTL_REG_EIE, ENC_EIE_RXERIE);
- enc_bset(enc, CTL_REG_EIE, ENC_EIE_TXERIE);
- enc_bset(enc, CTL_REG_EIE, ENC_EIE_INTIE);
-#endif
-
return 0;
}
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE (128 * 1024)
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
"1m(uboot),256k(environment),"\
"-(filesystem)"
-/* Unsupported features */
-#undef CONFIG_USE_IRQ
-
/* SPL */
#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/am33xx/u-boot-spl.lds"
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000)
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-#define CONFIG_STACKSIZE (128 * 1024)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
-#define CONFIG_STACKSIZE (2048)
-
#define CONFIG_BOOTARGS \
"console=ttyS0 root=/dev/mtdblock1 rootfstype=jffs2"
#define CONFIG_BOOTCOMMAND \
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
-#define CONFIG_STACKSIZE (2048)
-
#define CONFIG_BOOTARGS \
"root=mtd:main rootfstype=jffs2"
#define CONFIG_BOOTCOMMAND \
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
-#define CONFIG_STACKSIZE (2048)
-
#define CONFIG_BOOTARGS \
"console=ttyS0 root=/dev/mmcblk0p1 fbmem=600k rootwait=1"
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */
-#define CONFIG_STACKSIZE SZ_256K
/* GPIO Driver */
#define CONFIG_KONA_GPIO
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */
-#define CONFIG_STACKSIZE SZ_256K
/* GPIO Driver */
#define CONFIG_KONA_GPIO
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-#define CONFIG_STACKSIZE (256 * 1024)
/* Some commands use this as the default load address */
#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
#define CONFIG_SERIAL_TAG
/* misc */
-#define CONFIG_STACKSIZE (128 * 1024)
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
#define CONFIG_MISC_INIT_R
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/* Physical memory map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM (0x80000000)
#define CONFIG_EP93XX 1 /* This is a Cirrus Logic 93xx SoC */
#define CONFIG_SYS_CLK_FREQ 14745600 /* EP93xx has a 14.7456 clock */
-#undef CONFIG_USE_IRQ /* Don't need IRQ/FIQ */
/* Monitor configuration */
#undef CONFIG_CMD_DATE
/* Run-time memory allocatons */
#define CONFIG_SYS_GBL_DATA_SIZE 128
-#define CONFIG_STACKSIZE (128 * 1024)
-
-#if defined(CONFIG_USE_IRQ)
-#define CONFIG_STACKSIZE_IRQ (4 * 1024)
-#define CONFIG_STACKSIZE_FIQ (4 * 1024)
-#endif
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
#define CONFIG_SYS_MEMTEST_END 0x10800000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-#define CONFIG_STACKSIZE (128 * 1024)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-#define CONFIG_STACKSIZE (128 * 1024)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE (128 * 1024)
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
-#define CONFIG_STACKSIZE (2048)
-
-
/*
* After booting the board for the first time, new ethernet addresses
* should be generated and assigned to the environment variables
#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE SZ_128K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_LS102XA_STREAM_ID
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (30 * 1024)
-
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
#define CONFIG_LS102XA_STREAM_ID
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (30 * 1024)
-
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
#define CONFIG_LS102XA_STREAM_ID
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (30 * 1024)
-
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
#define CONFIG_SYS_HZ 1000
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (30 * 1024)
-
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_HZ 1000
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (30 * 1024)
-
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-#define CONFIG_STACKSIZE (128 * 1024)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_512M)
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_128M)
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000)
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000)
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE SZ_128K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE SZ_8K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_SKIP_LOWLEVEL_INIT /* X-Loader set everything up */
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-
/*
* Physical Memory Map
*/
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define CONFIG_STACKSIZE (256*1024) /* regular stack */
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/* Physical memory map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM (0x80000000)
#define CONFIG_SYS_SDRAM_BASE 0x88000000
#define CONFIG_SYS_MALLOC_LEN (256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN (4 << 10)
-#define CONFIG_STACKSIZE (4 << 10) /* regular stack */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (192 << 10)
#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE SZ_128K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_MALLOC_BASE (DDR_BASE_ADDR)
#endif
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
#if 0
/* Configure PXE */
#define CONFIG_BOOTP_PXE
# define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */
#endif /* SPI support */
-/* Unsupported features */
-#undef CONFIG_USE_IRQ
-
#define CONFIG_DRIVER_TI_CPSW
#define CONFIG_MII
#define CONFIG_PHY_GIGE
#define CONFIG_SYS_MALLOC_LEN (2 << 20)
-#define CONFIG_STACKSIZE (64 << 10)
-
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel"
#define CONFIG_BOOTCOMMAND \
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024)
-#define CONFIG_STACKSIZE (256 * 1024)
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel"
/* standalone support */
#define CONFIG_STANDALONE_LOAD_ADDR CONFIG_SYS_LOAD_ADDR
-/* baudrate */
-
-/* The stack sizes are set up in start.S using the settings below */
-#define CONFIG_STACKSIZE (256 << 10) /* 256 KiB */
-
/* FLASH and environment organization */
#define CONFIG_SYS_MONITOR_LEN (768 << 10) /* 768 KiB */
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-
/*
* Physical Memory Map
*/
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
-/* Unsupported features */
-#undef CONFIG_USE_IRQ
-
/* Ethernet */
#define CONFIG_DRIVER_TI_CPSW
#define CONFIG_MII
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
-/* Unsupported features */
-#undef CONFIG_USE_IRQ
-
#endif
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_LPAE_SDRAM_BASE 0x800000000
#define CONFIG_MAX_RAM_BANK_SIZE (2 << 30) /* 2GB */
-#define CONFIG_STACKSIZE (512 << 10) /* 512 KiB */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE - \
GENERATED_GBL_DATA_SIZE)
"panicboot=echo No boot device !!! reset\0" \
TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
-#define CONFIG_STACKSIZE (128u * SZ_1K)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000)
-#define CONFIG_STACKSIZE SZ_128K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_MEMTEST_START 0x80010000
#define CONFIG_SYS_MEMTEST_END 0x87C00000
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/* Physical memory map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM (0x80000000)
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000)
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_256M)
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
-#define CONFIG_STACKSIZE SZ_128K
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/*
* Physical Memory Map
*/
# define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */
#endif
-#define CONFIG_SYS_STACKSIZE (512 << 10) /* stack 512KB */
#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */
/* Linux boot param area in RAM (used only when booting linux) */
/* U-Boot general configuration */
/*==============================*/
-#undef CONFIG_USE_IRQ /* Keep it simple, poll only */
#define CONFIG_BOARD_POSTCLK_INIT
#define CONFIG_MISC_INIT_R
CONFIG_SSP2_BASE
CONFIG_SSP3_BASE
CONFIG_STACKBASE
-CONFIG_STACKSIZE
-CONFIG_STACKSIZE_FIQ
-CONFIG_STACKSIZE_IRQ
CONFIG_STANDALONE_LOAD_ADDR
CONFIG_STATIC_BOARD_REV
CONFIG_STATIC_RELA
CONFIG_SYS_SSD_BASE_PHYS
CONFIG_SYS_SST_SECT
CONFIG_SYS_SST_SECTSZ
-CONFIG_SYS_STACKSIZE
CONFIG_SYS_STACK_LENGTH
CONFIG_SYS_STACK_SIZE
CONFIG_SYS_STATUS_C
CONFIG_USER_LOWLEVEL_INIT
CONFIG_USE_FDT
CONFIG_USE_INTERRUPT
-CONFIG_USE_IRQ
CONFIG_USE_NAND
CONFIG_USE_NETDEV
CONFIG_USE_NOR
projects / people / ms / u-boot.git / commitdiff
