config TARGET_AT91SAM9M10G45EK
bool "Atmel AT91SAM9M10G45-EK board"
select CPU_ARM926EJS
+ select SUPPORT_SPL
config TARGET_PM9G45
bool "Ronetix pm9g45 board"
config TARGET_AT91SAM9N12EK
bool "Atmel AT91SAM9N12-EK board"
select CPU_ARM926EJS
+ select SUPPORT_SPL
config TARGET_AT91SAM9RLEK
bool "Atmel at91sam9rl reference board"
config TARGET_AT91SAM9X5EK
bool "Atmel AT91SAM9X5-EK board"
select CPU_ARM926EJS
+ select SUPPORT_SPL
config TARGET_SAMA5D3_XPLAINED
bool "SAMA5D3 Xplained board"
ifneq ($(CONFIG_SPL_BUILD),)
obj-$(CONFIG_AT91SAM9G20) += sdram.o spl_at91.o
obj-$(CONFIG_AT91SAM9M10G45) += mpddrc.o spl_at91.o
+obj-$(CONFIG_AT91SAM9N12) += mpddrc.o spl_at91.o
+obj-$(CONFIG_AT91SAM9X5) += mpddrc.o spl_at91.o
obj-$(CONFIG_SAMA5D3) += mpddrc.o spl_atmel.o
obj-$(CONFIG_SAMA5D4) += mpddrc.o spl_atmel.o
obj-y += spl.o
void at91_plla_init(u32 pllar)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
- int timeout = AT91_PLL_LOCK_TIMEOUT;
writel(pllar, &pmc->pllar);
- while (!(readl(&pmc->sr) & (AT91_PMC_LOCKA | AT91_PMC_MCKRDY))) {
- timeout--;
- if (timeout == 0)
- break;
- }
+ while (!(readl(&pmc->sr) & AT91_PMC_LOCKA))
+ ;
}
void at91_pllb_init(u32 pllbr)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
- int timeout = AT91_PLL_LOCK_TIMEOUT;
writel(pllbr, &pmc->pllbr);
- while (!(readl(&pmc->sr) & (AT91_PMC_LOCKB | AT91_PMC_MCKRDY))) {
- timeout--;
- if (timeout == 0)
- break;
- }
+ while (!(readl(&pmc->sr) & AT91_PMC_LOCKB))
+ ;
}
void at91_mck_init(u32 mckr)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
- int timeout = AT91_PLL_LOCK_TIMEOUT;
u32 tmp;
tmp = readl(&pmc->mckr);
- tmp &= ~(AT91_PMC_MCKR_PRES_MASK |
- AT91_PMC_MCKR_MDIV_MASK |
- AT91_PMC_MCKR_PLLADIV_MASK |
- AT91_PMC_MCKR_CSS_MASK);
- tmp |= mckr & (AT91_PMC_MCKR_PRES_MASK |
- AT91_PMC_MCKR_MDIV_MASK |
- AT91_PMC_MCKR_PLLADIV_MASK |
- AT91_PMC_MCKR_CSS_MASK);
+ tmp &= ~AT91_PMC_MCKR_PRES_MASK;
+ tmp |= mckr & AT91_PMC_MCKR_PRES_MASK;
writel(tmp, &pmc->mckr);
+ while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY))
+ ;
- while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY)) {
- timeout--;
- if (timeout == 0)
- break;
- }
+ tmp = readl(&pmc->mckr);
+ tmp &= ~AT91_PMC_MCKR_MDIV_MASK;
+ tmp |= mckr & AT91_PMC_MCKR_MDIV_MASK;
+ writel(tmp, &pmc->mckr);
+ while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY))
+ ;
+
+ tmp = readl(&pmc->mckr);
+ tmp &= ~AT91_PMC_MCKR_PLLADIV_MASK;
+ tmp |= mckr & AT91_PMC_MCKR_PLLADIV_MASK;
+ writel(tmp, &pmc->mckr);
+ while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY))
+ ;
+
+ tmp = readl(&pmc->mckr);
+ tmp &= ~AT91_PMC_MCKR_CSS_MASK;
+ tmp |= mckr & AT91_PMC_MCKR_CSS_MASK;
+ writel(tmp, &pmc->mckr);
+ while (!(readl(&pmc->sr) & AT91_PMC_MCKRDY))
+ ;
}
void at91_periph_clk_enable(int id)
#define TIMER_LOAD_VAL 0xfffff
-static inline unsigned long long tick_to_time(unsigned long long tick)
-{
- tick *= CONFIG_SYS_HZ;
- do_div(tick, gd->arch.timer_rate_hz);
-
- return tick;
-}
-
-static inline unsigned long long usec_to_tick(unsigned long long usec)
-{
- usec *= gd->arch.timer_rate_hz;
- do_div(usec, 1000000);
-
- return usec;
-}
-
/*
* Use the PITC in full 32 bit incrementing mode
*/
writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
gd->arch.timer_rate_hz = gd->arch.mck_rate_hz / 16;
- gd->arch.tbu = gd->arch.tbl = 0;
return 0;
}
-/*
- * Get the current 64 bit timer tick count
- */
-unsigned long long get_ticks(void)
-{
- at91_pit_t *pit = (at91_pit_t *) ATMEL_BASE_PIT;
-
- ulong now = readl(&pit->piir);
-
- /* increment tbu if tbl has rolled over */
- if (now < gd->arch.tbl)
- gd->arch.tbu++;
- gd->arch.tbl = now;
- return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;
-}
-
-void __udelay(unsigned long usec)
-{
- unsigned long long start;
- ulong tmo;
-
- start = get_ticks(); /* get current timestamp */
- tmo = usec_to_tick(usec); /* convert usecs to ticks */
- while ((get_ticks() - start) < tmo)
- ; /* loop till time has passed */
-}
-
-/*
- * get_timer(base) can be used to check for timeouts or
- * to measure elasped time relative to an event:
- *
- * ulong start_time = get_timer(0) sets start_time to the current
- * time value.
- * get_timer(start_time) returns the time elapsed since then.
- *
- * The time is used in CONFIG_SYS_HZ units!
- */
-ulong get_timer(ulong base)
-{
- return tick_to_time(get_ticks()) - base;
-}
-
/*
* Return the number of timer ticks per second.
*/
--- /dev/null
+/*
+ * Copyright (C) 2015 Atmel Corporation
+ * Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE, \
+ LENGTH = CONFIG_SPL_MAX_SIZE }
+MEMORY { .sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \
+ LENGTH = CONFIG_SPL_BSS_MAX_SIZE }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ .text :
+ {
+ __start = .;
+ *(.vectors)
+ arch/arm/cpu/arm926ejs/start.o (.text*)
+ *(.text*)
+ } >.sram
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+ . = ALIGN(4);
+ .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+
+ . = ALIGN(4);
+ __image_copy_end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
+
+ .bss :
+ {
+ . = ALIGN(4);
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end = .;
+ } >.sdram
+}
#define TIMER_LOAD_VAL 0xfffff
-static inline unsigned long long tick_to_time(unsigned long long tick)
-{
- tick *= CONFIG_SYS_HZ;
- do_div(tick, gd->arch.timer_rate_hz);
-
- return tick;
-}
-
-static inline unsigned long long usec_to_tick(unsigned long long usec)
-{
- usec *= gd->arch.timer_rate_hz;
- do_div(usec, 1000000);
-
- return usec;
-}
-
/*
* Use the PITC in full 32 bit incrementing mode
*/
gd->arch.timer_rate_hz = get_pit_clk_rate() / 16;
- gd->arch.tbu = 0;
- gd->arch.tbl = 0;
-
return 0;
}
-/*
- * Get the current 64 bit timer tick count
- */
-unsigned long long get_ticks(void)
-{
- at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT;
-
- ulong now = readl(&pit->piir);
-
- /* increment tbu if tbl has rolled over */
- if (now < gd->arch.tbl)
- gd->arch.tbu++;
- gd->arch.tbl = now;
- return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;
-}
-
-void __udelay(unsigned long usec)
-{
- unsigned long long start;
- ulong tmo;
-
- start = get_ticks(); /* get current timestamp */
- tmo = usec_to_tick(usec); /* convert usecs to ticks */
- while ((get_ticks() - start) < tmo)
- ; /* loop till time has passed */
-}
-
-/*
- * get_timer(base) can be used to check for timeouts or
- * to measure elasped time relative to an event:
- *
- * ulong start_time = get_timer(0) sets start_time to the current
- * time value.
- * get_timer(start_time) returns the time elapsed since then.
- *
- * The time is used in CONFIG_SYS_HZ units!
- */
-ulong get_timer(ulong base)
-{
- return tick_to_time(get_ticks()) - base;
-}
-
/*
* Return the number of timer ticks per second.
*/
#define AT91_PMC_MCKR_CSS_PLLB 0x00000003
#define AT91_PMC_MCKR_CSS_MASK 0x00000003
-#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
+#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4) || \
+ defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
#define AT91_PMC_MCKR_PRES_1 0x00000000
#define AT91_PMC_MCKR_PRES_2 0x00000010
#define AT91_PMC_MCKR_PRES_4 0x00000020
#else
#define AT91_PMC_MCKR_MDIV_1 0x00000000
#define AT91_PMC_MCKR_MDIV_2 0x00000100
-#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
+#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4) || \
+ defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
#define AT91_PMC_MCKR_MDIV_3 0x00000300
#endif
#define AT91_PMC_MCKR_MDIV_4 0x00000200
#define ATMEL_BASE_CS6 0x70000000
#define ATMEL_BASE_CS7 0x80000000
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffd3c
+
/*
* Other misc defines
*/
#define ATMEL_BASE_CS6 0x70000000
#define ATMEL_BASE_CS7 0x80000000
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffd3c
+
/*
* Other misc defines
*/
#define ATMEL_BASE_CS6 0x70000000
#define ATMEL_BASE_CS7 0x80000000
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffd3c
+
/*
* Other misc defines
*/
#define ATMEL_BASE_CS6 0x70000000
#define ATMEL_BASE_CS7 0x80000000
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffd3c
+
/*
* Other misc defines
*/
#define ATMEL_BASE_CS4 0x50000000 /* Compact Flash Slot 0 */
#define ATMEL_BASE_CS5 0x60000000 /* Compact Flash Slot 1 */
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffd3c
+
/*
* Other misc defines
*/
#define ATMEL_BASE_EHCI 0x00700000 /* USB Host controller (EHCI) */
#endif
+/*
+ * External memory
+ */
+#define ATMEL_BASE_CS0 0x10000000
+#define ATMEL_BASE_CS1 0x20000000
+#define ATMEL_BASE_CS2 0x30000000
+#define ATMEL_BASE_CS3 0x40000000
+#define ATMEL_BASE_CS4 0x50000000
+#define ATMEL_BASE_CS5 0x60000000
+
/* 9x5 series chip id definitions */
#define ARCH_ID_AT91SAM9X5 0x819a05a0
#define ARCH_ID_VERSION_MASK 0x1f
#define ATMEL_CPU_NAME get_cpu_name()
#endif
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffe3c
+
/*
* Other misc defines
*/
#define PIO_SCDR_DIV 0x3fff
#define CPU_HAS_PCR
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfffffe3c
+
/*
* PMECC table in ROM
*/
#define cpu_is_sama5d44() (cpu_is_sama5d4() && \
(get_extension_chip_id() == ARCH_EXID_SAMA5D44))
+/* Timer */
+#define CONFIG_SYS_TIMER_COUNTER 0xfc06863c
+
/*
* No PMECC Galois table in ROM
*/
static int ddr2_decodtype_is_seq(u32 cr)
{
-#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
+#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4) || \
+ defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
if (cr & ATMEL_MPDDRC_CR_DECOD_INTERLEAVED)
return 0;
#endif
return BOOT_DEVICE_MMC1;
#elif CONFIG_SYS_USE_NANDFLASH
return BOOT_DEVICE_NAND;
-#elif CONFIG_SYS_USE_SERIALFLASH
+#elif CONFIG_SYS_USE_SERIALFLASH || CONFIG_SYS_USE_SPIFLASH
return BOOT_DEVICE_SPI;
#endif
return BOOT_DEVICE_NONE;
{
}
-void spl_board_init(void)
+void __weak spl_board_init(void)
+{
+}
+
+void board_init_f(ulong dummy)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
timer_init();
/* enable clocks for all PIOs */
+#if defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
+ at91_periph_clk_enable(ATMEL_ID_PIOAB);
+ at91_periph_clk_enable(ATMEL_ID_PIOCD);
+#else
at91_periph_clk_enable(ATMEL_ID_PIOA);
at91_periph_clk_enable(ATMEL_ID_PIOB);
at91_periph_clk_enable(ATMEL_ID_PIOC);
+#endif
/* init console */
at91_seriald_hw_init();
preloader_console_init();
/* This only be used for sama5d4 soc now */
}
+/* empty stub to satisfy current lowlevel_init, can be removed any time */
void s_init(void)
+{
+}
+
+void board_init_f(ulong dummy)
{
switch_to_main_crystal_osc();
preloader_console_init();
mem_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ board_init_r(NULL, 0);
}
#include <common.h>
#include <asm/io.h>
+#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
+#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
}
#endif
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+ /*
+ * On the at91sam9m10g45ek board, the chip wm9711 stays in the
+ * test mode, so it needs do some action to exit test mode.
+ */
+ at91_periph_clk_enable(ATMEL_ID_PIODE);
+ at91_set_gpio_output(AT91_PIN_PD7, 0);
+ at91_set_gpio_output(AT91_PIN_PD8, 0);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
+
+#ifdef CONFIG_SYS_USE_MMC
+ at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+ at91sam9m10g45ek_nand_hw_init();
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_14 |
+ ATMEL_MPDDRC_CR_DQMS_SHARED |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
+
+ ddr2->rtr = 0x24b;
+
+ ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
+ 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
+ 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
+ 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct atmel_mpddr ddr2;
+ unsigned long csa;
+
+ ddr2_conf(&ddr2);
+
+ /* enable DDR2 clock */
+ writel(0x4, &pmc->scer);
+
+ /* Chip select 1 is for DDR2/SDRAM */
+ csa = readl(&mat->ebicsa);
+ csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+ csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
+ writel(csa, &mat->ebicsa);
+
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_CS6, &ddr2);
+}
+#endif
+
#ifdef CONFIG_CMD_USB
static void at91sam9m10g45ek_usb_hw_init(void)
{
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
+
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+#ifdef CONFIG_SYS_USE_MMC
+ at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+ at91sam9n12ek_nand_hw_init();
+#elif CONFIG_SYS_USE_SPIFLASH
+ at91_spi0_hw_init(1 << 4);
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_13 |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+ ATMEL_MPDDRC_CR_NB_8BANKS |
+ ATMEL_MPDDRC_CR_DECOD_INTERLEAVED);
+
+ ddr2->rtr = 0x411;
+
+ ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
+ 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct atmel_mpddr ddr2;
+ unsigned long csa;
+
+ ddr2_conf(&ddr2);
+
+ /* enable DDR2 clock */
+ writel(0x4, &pmc->scer);
+
+ /* Chip select 1 is for DDR2/SDRAM */
+ csa = readl(&matrix->ebicsa);
+ csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+ csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
+ csa |= AT91_MATRIX_EBI_DBPD_OFF;
+ csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
+ writel(csa, &matrix->ebicsa);
+
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_CS1, &ddr2);
+}
+#endif
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
+
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+#ifdef CONFIG_SYS_USE_MMC
+ at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+ at91sam9x5ek_nand_hw_init();
+#elif CONFIG_SYS_USE_SPIFLASH
+ at91_spi0_hw_init(1 << 4);
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_13 |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+ ATMEL_MPDDRC_CR_NB_8BANKS |
+ ATMEL_MPDDRC_CR_DECOD_INTERLEAVED);
+
+ ddr2->rtr = 0x411;
+
+ ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
+ 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct atmel_mpddr ddr2;
+ unsigned long csa;
+
+ ddr2_conf(&ddr2);
+
+ /* enable DDR2 clock */
+ writel(0x4, &pmc->scer);
+
+ /* Chip select 1 is for DDR2/SDRAM */
+ csa = readl(&matrix->ebicsa);
+ csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+ csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
+ csa |= AT91_MATRIX_EBI_DBPD_OFF;
+ csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
+ writel(csa, &matrix->ebicsa);
+
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_CS1, &ddr2);
+}
+#endif
#include <netdev.h>
#include <nand.h>
#include <spi.h>
+#include <version.h>
DECLARE_GLOBAL_DATA_PTR;
int i;
char temp[32];
+ lcd_printf("%s\n", U_BOOT_VERSION);
lcd_printf("2014 ATMEL Corp\n");
lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
strmhz(temp, get_cpu_clk_rate()));
#include <netdev.h>
#include <nand.h>
#include <spi.h>
+#include <version.h>
DECLARE_GLOBAL_DATA_PTR;
int i;
char temp[32];
+ lcd_printf("%s\n", U_BOOT_VERSION);
lcd_printf("2014 ATMEL Corp\n");
lcd_printf("at91@atmel.com\n");
lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_MMC"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9N12,SYS_USE_NANDFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9N12,SYS_USE_SPIFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_NANDFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_SPIFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,MACH_TYPE=2066,SYS_USE_NANDFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_CORVUS=y
nand->dev_ready = at91_nand_wait_ready;
#endif
nand->chip_delay = 20;
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+ nand->bbt_options |= NAND_BBT_USE_FLASH;
+#endif
#ifdef CONFIG_ATMEL_NAND_HWECC
#ifdef CONFIG_ATMEL_NAND_HW_PMECC
nand->dev_ready = at91_nand_ready;
#endif
nand->chip_delay = 75;
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+ nand->bbt_options |= NAND_BBT_USE_FLASH;
+#endif
ret = nand_scan_ident(mtd, CONFIG_SYS_NAND_MAX_CHIPS, NULL);
if (ret)
--- /dev/null
+/*
+ * Common part of configuration settings for the AT91 SAMA5 board.
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ * Josh Wu <josh.wu@atmel.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __AT91_SAMA5_COMMON_H
+#define __AT91_SAMA5_COMMON_H
+
+#include <asm/hardware.h>
+
+#define CONFIG_SYS_TEXT_BASE 0x26f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
+
+#define CONFIG_ARCH_CPU_INIT
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT /* Device Tree support */
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* general purpose I/O */
+#define CONFIG_AT91_GPIO
+
+#define CONFIG_BOOTDELAY 3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_LOADS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,115200 earlyprintk " \
+ "root=/dev/mmcblk0p2 rw rootwait"
+#else
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,115200 earlyprintk " \
+ "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
+ "256K(env),256k(evn_redundent),256k(spare)," \
+ "512k(dtb),6M(kernel)ro,-(rootfs) " \
+ "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_PROMPT "U-Boot> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+#endif
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x300000
+#define CONFIG_SPL_MAX_SIZE 0x010000
+#define CONFIG_SPL_STACK 0x310000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+#define CONFIG_SYS_MONITOR_LEN 0x80000
+
+#ifdef CONFIG_SYS_USE_MMC
+
+#define CONFIG_SPL_BSS_START_ADDR 0x70000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START 0x70080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
+
+#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
+
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define CONFIG_SYS_AT91_PLLA 0x20c73f03
+#define CONFIG_SYS_MCKR 0x1301
+#define CONFIG_SYS_MCKR_CSS 0x1302
+
+#define ATMEL_BASE_MPDDRC ATMEL_BASE_DDRSDRC0
#endif
#else /* CONFIG_SYS_USE_MMC */
/* bootstrap + u-boot + env + linux in mmc */
-#define CONFIG_ENV_IS_IN_MMC
-/* For FAT system, most cases it should be in the reserved sector */
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+/* Use raw reserved sectors to save environment */
#define CONFIG_ENV_OFFSET 0x2000
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_SYS_MMC_ENV_DEV 0
+#else
+/* Use file in FAT file to save environment */
+#define CONFIG_ENV_IS_IN_FAT
+#define CONFIG_FAT_WRITE
+#define FAT_ENV_INTERFACE "mmc"
+#define FAT_ENV_FILE "uboot.env"
+#define FAT_ENV_DEVICE_AND_PART "0"
+#define CONFIG_ENV_SIZE 0x4000
+#endif
+
#define CONFIG_BOOTCOMMAND \
"setenv bootargs ${console} ${mtdparts} ${bootargs_mmc};" \
"fatload mmc 0:1 0x21000000 dtb;" \
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-#define CONFIG_STACKSIZE (32 * 1024) /* regular stack */
+
+/* SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x300000
+#define CONFIG_SPL_MAX_SIZE 0x6000
+#define CONFIG_SPL_STACK 0x308000
+
+#define CONFIG_SPL_BSS_START_ADDR 0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN (512 << 10)
+
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define CONFIG_SYS_AT91_PLLA 0x20953f03
+#define CONFIG_SYS_MCKR 0x1301
+#define CONFIG_SYS_MCKR_CSS 0x1302
+
+#define ATMEL_BASE_MPDDRC ATMEL_BASE_DDRSDRC
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
+#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
+
+#elif CONFIG_SYS_USE_SPIFLASH
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
+
+#endif
#endif
*/
#define CONFIG_SYS_MALLOC_LEN (512 * 1024 + 0x1000)
+/* SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x300000
+#define CONFIG_SPL_MAX_SIZE 0x6000
+#define CONFIG_SPL_STACK 0x308000
+
+#define CONFIG_SPL_BSS_START_ADDR 0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN (512 << 10)
+
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define CONFIG_SYS_AT91_PLLA 0x20c73f03
+#define CONFIG_SYS_MCKR 0x1301
+#define CONFIG_SYS_MCKR_CSS 0x1302
+
+#define ATMEL_BASE_MPDDRC ATMEL_BASE_DDRSDRC
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
+#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
+
+#elif CONFIG_SYS_USE_SPIFLASH
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
+
+#endif
+
#endif
#include <asm/hardware.h>
-#define MACH_TYPE_CORVUS 2066
-
-#define CONFIG_MACH_TYPE MACH_TYPE_CORVUS
#define CONFIG_SYS_GENERIC_BOARD
/*
* Warning: changing CONFIG_SYS_TEXT_BASE requires
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_TEXT_BASE 0x26f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT /* Device Tree support */
-
-#define CONFIG_SYS_GENERIC_BOARD
+/* No NOR flash, this definition should put before common header */
+#define CONFIG_SYS_NO_FLASH
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
+#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
*/
#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* No NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_LOADS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
#define CONFIG_ENV_IS_NOWHERE
#endif
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "root=/dev/mmcblk0p2 rw rootwait"
-#else
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
- "256K(env),256k(evn_redundent),256k(spare)," \
- "512k(dtb),6M(kernel)ro,-(rootfs) " \
- "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x300000
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_TEXT_BASE 0x26f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT /* Device Tree support */
-
-#define CONFIG_SYS_GENERIC_BOARD
-
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
+/*
+ * If has No NOR flash, please put the definition: CONFIG_SYS_NO_FLASH
+ * before the common header.
+ */
+#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
/* board specific (not enough SRAM) */
#define CONFIG_SAMA5D3_LCD_BASE 0x23E00000
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/* NOR flash */
+#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_CMD_FLASH
-
-#ifdef CONFIG_CMD_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_FLASH_BASE 0x10000000
#define CONFIG_SYS_MAX_FLASH_SECT 131
#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#else
-#define CONFIG_SYS_NO_FLASH
#endif
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_LOADS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
#define CONFIG_ENV_IS_NOWHERE
#endif
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "root=/dev/mmcblk0p2 rw rootwait"
-#else
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
- "256K(env),256k(evn_redundent),256k(spare)," \
- "512k(dtb),6M(kernel)ro,-(rootfs) " \
- "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x300000
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_TEXT_BASE 0x26f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT /* Device Tree support */
-
-#define CONFIG_SYS_GENERIC_BOARD
+/* No NOR flash, this definition should put before common header */
+#define CONFIG_SYS_NO_FLASH
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
+#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_USART3
#define CONFIG_USART_ID ATMEL_ID_USART3
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* No NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_LOADS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SETEXPR
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
"bootz 0x22000000 - 0x21000000"
#endif
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "root=/dev/mmcblk0p2 rw rootwait"
-#else
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
- "256K(env),256k(evn_redundent),256k(spare)," \
- "512k(dtb),6M(kernel)ro,-(rootfs) " \
- "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/* SPL */
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_TEXT_BASE 0x26f00000
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT /* Device Tree support */
-
-#define CONFIG_SYS_GENERIC_BOARD
+/* No NOR flash, this definition should put before common header */
+#define CONFIG_SYS_NO_FLASH
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
+#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_USART3
#define CONFIG_USART_ID ATMEL_ID_USART3
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* No NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_LOADS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SETEXPR
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
"bootz 0x22000000 - 0x21000000"
#endif
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "root=/dev/mmcblk0p2 rw rootwait"
-#else
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200 earlyprintk " \
- "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
- "256K(env),256k(evn_redundent),256k(spare)," \
- "512k(dtb),6M(kernel)ro,-(rootfs) " \
- "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
projects / people / ms / u-boot.git / commitdiff
