U-boot Env | 1MB | 0x4020_0000
PPA FIT image | 2MB | 0x4050_0000
Linux ITB | ~53MB | 0x40A0_0000
+
+LS1012A2G5RDB board Overview
+-----------------------
+ - SERDES Connections, 3 lanes supporting:
+ - SGMII, SGMII 2.5
+ - SATA 3.0
+ - DDR Controller
+ - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
+ -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
+ signals to
+ - QSPI NOR flash memory
+ - USB 3.0
+ - one high-speed USB 2.0/3.0 port.
+ - SDIO WiFi, SPI
+ - 2 I2C controllers
+ - One SATA onboard connectors
+ - UART
+ - The LS1012A processor consists of two UART controllers,
+ out of which only UART1 is used on 2G5RDB.
+ - ARM JTAG support
+
+Major Difference between LS1012ARDB and LS1012A-2G5RDB
+------------------------------------------------------
+1. LS1012A-2G5RDB has Type C USB connector unlike USB Type A/B of LS1012ARDB
+2. LS1012A-2G5RDB has 2 2.5G AQR PHY unlike 2 1G Realtek RTL8211FS PHYs
+ of LS1012ARDB
+3. LS1012A-2G5RDB is not having Arduino header
+4. LS1012A-2G5RDB doesn't have PCI slot
+
+Booting Options
+---------------
+QSPI Flash
+
+QSPI flash map
+--------------
+Images | Size |QSPI Flash Address
+------------------------------------------
+RCW + PBI | 1MB | 0x4000_0000
+U-boot | 1MB | 0x4010_0000
+U-boot Env | 1MB | 0x4030_0000
+PPA FIT image | 2MB | 0x4040_0000
+PFE firmware | 20K | 0x00a0_0000
+Linux ITB | ~53MB | 0x4100_0000
--- /dev/null
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1012A2G5RDB_H__
+#define __LS1012A2G5RDB_H__
+
+#include "ls1012a_common.h"
+
+/* PFE Ethernet */
+#ifdef CONFIG_FSL_PFE
+#define EMAC1_PHY_ADDR 0x2
+#define EMAC2_PHY_ADDR 0x1
+#define CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_AQUANTIA
+#endif
+
+/* DDR */
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_SYS_SDRAM_SIZE 0x40000000
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+/* MMC */
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+
+#define CONFIG_SYS_SATA AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_NET_MULTI
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "verify=no\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "fdt_addr=0x00f00000\0" \
+ "kernel_addr=0x01000000\0" \
+ "kernelheader_addr=0x800000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernelheader_size=0x40000\0" \
+ "console=ttyS0,115200\0" \
+ BOOTENV \
+ "boot_scripts=ls1012ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1012ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;" \
+ "\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "installer=load mmc 0:2 $load_addr " \
+ "/flex_installer_arm64.itb; " \
+ "bootm $load_addr#$board\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_addr " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
+ "bootm $load_addr#$board\0"
+
+#undef CONFIG_BOOTCOMMAND
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
+ "env exists secureboot && esbc_halt;"
+#endif
+
+#define DEFAULT_PFE_MDIO_NAME "PFE_MDIO"
+#define DEFAULT_PFE_MDIO1_NAME "PFE_MDIO1"
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1012A2G5RDB_H__ */
projects / people / ms / u-boot.git / commitdiff
