mke2fs.8, badblocks.8: fix spelling errors and other miscellaneous typos

Reported-by: Pete <pete@leptonyx.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

diff --git a/misc/badblocks.8.in b/misc/badblocks.8.in
index f507f63b9a09f6dcd09ba6e262573f55cdbeeda2..c0b9ff163b229eab8f4d77fcb44eab18509b1b56 100644 (file)
--- a/misc/badblocks.8.in
+++ b/misc/badblocks.8.in
@@ -9,21 +9,21 @@ badblocks \- search a device for bad blocks
 ]
 [
 .B \-b
-.I block-size
+.I block_size
 ]
 [
 .B \-c
 .I blocks_at_once
 ]
 [
-.B \-e
-.I max_bad_blocks
-]
-[
 .B \-d
 .I read_delay_factor
 ]
 [
+.B \-e
+.I max_bad_blocks
+]
+[
 .B \-i
 .I input_file
 ]
@@ -41,9 +41,9 @@ badblocks \- search a device for bad blocks
 ]
 .I device
 [
-.I last-block
+.I last_block
 ] [
-.I first-block 
+.I first_block
 ]
 .SH DESCRIPTION
 .B badblocks
@@ -51,10 +51,10 @@ is used to search for bad blocks on a device (usually a disk partition).
 .I device
 is the special file corresponding to the device (e.g
 .IR /dev/hdc1 ).
-.I last-block
+.I last_block
 is the last block to be checked; if it is not specified, the last block
 on the device is used as a default.
-.I first-block
+.I first_block
 is an optional parameter specifying the starting block number
 for the test, which allows the testing to start in the middle of the
 disk.  If it is not specified the first block on the disk is used as a default.
@@ -83,17 +83,12 @@ and
 programs.
 .SH OPTIONS
 .TP
-.BI \-b " block-size"
+.BI \-b " block_size"
 Specify the size of blocks in bytes.  The default is 1024.
 .TP
 .BI \-c " number of blocks"
 is the number of blocks which are tested at a time.  The default is 64.
 .TP
-.BI \-e " max bad block count"
-Specify a maximum number of bad blocks before aborting the test.  The
-default is 0, meaning the test will continue until the end of the test
-range is reached.
-.TP
 .BI \-d " read delay factor"
 This parameter, if passed and non-zero, will cause bad blocks to sleep
 between reads if there were no errors encountered in the read
@@ -102,6 +97,11 @@ took for the read operation to be performed. In other words, a value of
 100 will cause each read to be delayed by the amount the previous read
 took, and a value of 200 by twice the amount.
 .TP
+.BI \-e " max bad block count"
+Specify a maximum number of bad blocks before aborting the test.  The
+default is 0, meaning the test will continue until the end of the test
+range is reached.
+.TP
 .B \-f
 Normally, badblocks will refuse to do a read/write or a non-destructive
 test on a device which is mounted, since either can cause the system to

diff --git a/misc/mke2fs.8.in b/misc/mke2fs.8.in
index 429ceba3026850d721e43ef378a65c000b796d93..79aba3ca2e6dbf821261769efd64a1ffc1bc2ac6 100644 (file)
--- a/misc/mke2fs.8.in
+++ b/misc/mke2fs.8.in
@@ -666,12 +666,12 @@ program should be run immediately after this option is used, and there
 is no guarantee that any data will be salvageable.  Due to the wide
 variety of possible options to
 .BR mke2fs
-that affect the on-disk layout, is critical to specify exactly the same
+that affect the on-disk layout, it is critical to specify exactly
 the same format options, such as blocksize, fs-type, feature flags, and
 other tunables when using this option, or the filesystem will be further
 corrupted.  In some cases, such as filesystems that have been resized,
 or have had features enabled after format time, it is impossible to
-overwrite all of the superblocks corretly, and at least some filesystem
+overwrite all of the superblocks correctly, and at least some filesystem
 corruption will occur.  It is best to run this on a full copy of the
 filesystem so other options can be tried if this doesn't work.
 .\" .TP