board/xes/xpedite1000/xpedite1000.c

   1 /*
   2  * Copyright (C) 2003 Travis B. Sawyer <travis.sawyer@sandburst.com>
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <console.h>
   9 #include <asm/processor.h>
  10 #include <spd_sdram.h>
  11 #include <i2c.h>
  12 #include <net.h>
  13
  14 DECLARE_GLOBAL_DATA_PTR;
  15
  16 int board_early_init_f(void)
  17 {
  18         unsigned long sdrreg;
  19
  20         /*
  21          * Enable GPIO for pins 18 - 24
  22          * 18 = SEEPROM_WP
  23          * 19 = #M_RST
  24          * 20 = #MONARCH
  25          * 21 = #LED_ALARM
  26          * 22 = #LED_ACT
  27          * 23 = #LED_STATUS1
  28          * 24 = #LED_STATUS2
  29          */
  30         mfsdr(SDR0_PFC0, sdrreg);
  31         mtsdr(SDR0_PFC0, (sdrreg & ~SDR0_PFC0_TRE_ENABLE) | 0x00003e00);
  32         out32(CONFIG_SYS_GPIO_BASE + 0x018, (USR_LED0 | USR_LED1 | USR_LED2 | USR_LED3));
  33         LED0_OFF();
  34         LED1_OFF();
  35         LED2_OFF();
  36         LED3_OFF();
  37
  38         /* Setup the external bus controller/chip selects */
  39         mtebc(PB0AP, 0x04055200);       /* 16MB Strata FLASH */
  40         mtebc(PB0CR, 0xff098000);       /* BAS=0xff0 16MB R/W 8-bit */
  41         mtebc(PB1AP, 0x04055200);       /* 512KB Socketed AMD FLASH */
  42         mtebc(PB1CR, 0xfe018000);       /* BAS=0xfe0 1MB R/W 8-bit */
  43         mtebc(PB6AP, 0x05006400);       /* 32-64MB AMD MirrorBit FLASH */
  44         mtebc(PB6CR, 0xf00da000);       /* BAS=0xf00 64MB R/W i6-bit */
  45         mtebc(PB7AP, 0x05006400);       /* 32-64MB AMD MirrorBit FLASH */
  46         mtebc(PB7CR, 0xf40da000);       /* BAS=0xf40 64MB R/W 16-bit */
  47
  48         /*
  49          * Setup the interrupt controller polarities, triggers, etc.
  50          *
  51          * Because of the interrupt handling rework to handle 440GX interrupts
  52          * with the common code, we needed to change names of the UIC registers.
  53          * Here the new relationship:
  54          *
  55          * U-Boot name  440GX name
  56          * -----------------------
  57          * UIC0         UICB0
  58          * UIC1         UIC0
  59          * UIC2         UIC1
  60          * UIC3         UIC2
  61          */
  62         mtdcr(UIC1SR, 0xffffffff);      /* clear all */
  63         mtdcr(UIC1ER, 0x00000000);      /* disable all */
  64         mtdcr(UIC1CR, 0x00000003);      /* SMI & UIC1 crit are critical */
  65         mtdcr(UIC1PR, 0xfffffe00);      /* per ref-board manual */
  66         mtdcr(UIC1TR, 0x01c00000);      /* per ref-board manual */
  67         mtdcr(UIC1VR, 0x00000001);      /* int31 highest, base=0x000 */
  68         mtdcr(UIC1SR, 0xffffffff);      /* clear all */
  69
  70         mtdcr(UIC2SR, 0xffffffff);      /* clear all */
  71         mtdcr(UIC2ER, 0x00000000);      /* disable all */
  72         mtdcr(UIC2CR, 0x00000000);      /* all non-critical */
  73         mtdcr(UIC2PR, 0xffffc0ff);      /* per ref-board manual */
  74         mtdcr(UIC2TR, 0x00ff8000);      /* per ref-board manual */
  75         mtdcr(UIC2VR, 0x00000001);      /* int31 highest, base=0x000 */
  76         mtdcr(UIC2SR, 0xffffffff);      /* clear all */
  77
  78         mtdcr(UIC3SR, 0xffffffff);      /* clear all */
  79         mtdcr(UIC3ER, 0x00000000);      /* disable all */
  80         mtdcr(UIC3CR, 0x00000000);      /* all non-critical */
  81         mtdcr(UIC3PR, 0xffffffff);      /* per ref-board manual */
  82         mtdcr(UIC3TR, 0x00ff8c0f);      /* per ref-board manual */
  83         mtdcr(UIC3VR, 0x00000001);      /* int31 highest, base=0x000 */
  84         mtdcr(UIC3SR, 0xffffffff);      /* clear all */
  85
  86         mtdcr(UIC0SR, 0xfc000000);      /* clear all */
  87         mtdcr(UIC0ER, 0x00000000);      /* disable all */
  88         mtdcr(UIC0CR, 0x00000000);      /* all non-critical */
  89         mtdcr(UIC0PR, 0xfc000000);      /* */
  90         mtdcr(UIC0TR, 0x00000000);      /* */
  91         mtdcr(UIC0VR, 0x00000001);      /* */
  92
  93         LED0_ON();
  94
  95         return 0;
  96 }
  97
  98 int checkboard(void)
  99 {
 100         char buf[64];
 101         int i;
 102
 103         printf("Board: X-ES %s PMC SBC\n", CONFIG_SYS_BOARD_NAME);
 104         printf("       ");
 105         i = getenv_f("board_rev", buf, sizeof(buf));
 106         if (i > 0)
 107                 printf("Rev %s, ", buf);
 108         i = getenv_f("serial#", buf, sizeof(buf));
 109         if (i > 0)
 110                 printf("Serial# %s, ", buf);
 111         i = getenv_f("board_cfg", buf, sizeof(buf));
 112         if (i > 0)
 113                 printf("Cfg %s", buf);
 114         printf("\n");
 115
 116         return 0;
 117 }
 118
 119 phys_size_t initdram(void)
 120 {
 121         return spd_sdram();
 122 }
 123
 124 /*
 125  * Override weak pci_pre_init()
 126  *
 127  * This routine is called just prior to registering the hose and gives
 128  * the board the opportunity to check things. Returning a value of zero
 129  * indicates that things are bad & PCI initialization should be aborted.
 130  *
 131  * Different boards may wish to customize the pci controller structure
 132  * (add regions, override default access routines, etc) or perform
 133  * certain pre-initialization actions.
 134  */
 135 #if defined(CONFIG_PCI)
 136 int pci_pre_init(struct pci_controller * hose)
 137 {
 138         unsigned long strap;
 139
 140         /* See if we're supposed to setup the pci */
 141         mfsdr(SDR0_SDSTP1, strap);
 142         if ((strap & 0x00010000) == 0)
 143                 return 0;
 144
 145 #if defined(CONFIG_SYS_PCI_FORCE_PCI_CONV)
 146         /* Setup System Device Register PCIL0_XCR */
 147         mfsdr(SDR0_XCR, strap);
 148         strap &= 0x0f000000;
 149         mtsdr(SDR0_XCR, strap);
 150 #endif
 151
 152         return 1;
 153 }
 154 #endif /* defined(CONFIG_PCI) */
 155
 156 #if defined(CONFIG_PCI)
 157 /*
 158  * Override weak is_pci_host()
 159  *
 160  * This routine is called to determine if a pci scan should be
 161  * performed. With various hardware environments (especially cPCI and
 162  * PPMC) it's insufficient to depend on the state of the arbiter enable
 163  * bit in the strap register, or generic host/adapter assumptions.
 164  *
 165  * Rather than hard-code a bad assumption in the general 440 code, the
 166  * 440 pci code requires the board to decide at runtime.
 167  *
 168  * Return 0 for adapter mode, non-zero for host (monarch) mode.
 169  */
 170 int is_pci_host(struct pci_controller *hose)
 171 {
 172         return ((in32(CONFIG_SYS_GPIO_BASE + 0x1C) & 0x00000800) == 0);
 173 }
 174 #endif /* defined(CONFIG_PCI) */
 175
 176 #ifdef CONFIG_POST
 177 /*
 178  * Returns 1 if keys pressed to start the power-on long-running tests
 179  * Called from board_init_f().
 180  */
 181 int post_hotkeys_pressed(void)
 182 {
 183         return ctrlc();
 184 }
 185 #endif