+ * @NL80211_ATTR_MLO_LINK_ID: A (u8) link ID for use with MLO, to be used with
+ * various commands that need a link ID to operate.
+ * @NL80211_ATTR_MLO_LINKS: A nested array of links, each containing some
+ * per-link information and a link ID.
+ * @NL80211_ATTR_MLD_ADDR: An MLD address, used with various commands such as
+ * authenticate/associate.
+ *
+ * @NL80211_ATTR_MLO_SUPPORT: Flag attribute to indicate user space supports MLO
+ * connection. Used with %NL80211_CMD_CONNECT. If this attribute is not
+ * included in NL80211_CMD_CONNECT drivers must not perform MLO connection.
+ *
+ * @NL80211_ATTR_MAX_NUM_AKM_SUITES: U16 attribute. Indicates maximum number of
+ * AKM suites allowed for %NL80211_CMD_CONNECT, %NL80211_CMD_ASSOCIATE and
+ * %NL80211_CMD_START_AP in %NL80211_CMD_GET_WIPHY response. If this
+ * attribute is not present userspace shall consider maximum number of AKM
+ * suites allowed as %NL80211_MAX_NR_AKM_SUITES which is the legacy maximum
+ * number prior to the introduction of this attribute.
+ *
+ * @NL80211_ATTR_EML_CAPABILITY: EML Capability information (u16)
+ * @NL80211_ATTR_MLD_CAPA_AND_OPS: MLD Capabilities and Operations (u16)
+ *
+ * @NL80211_ATTR_TX_HW_TIMESTAMP: Hardware timestamp for TX operation in
+ * nanoseconds (u64). This is the device clock timestamp so it will
+ * probably reset when the device is stopped or the firmware is reset.
+ * When used with %NL80211_CMD_FRAME_TX_STATUS, indicates the frame TX
+ * timestamp. When used with %NL80211_CMD_FRAME RX notification, indicates
+ * the ack TX timestamp.
+ * @NL80211_ATTR_RX_HW_TIMESTAMP: Hardware timestamp for RX operation in
+ * nanoseconds (u64). This is the device clock timestamp so it will
+ * probably reset when the device is stopped or the firmware is reset.
+ * When used with %NL80211_CMD_FRAME_TX_STATUS, indicates the ack RX
+ * timestamp. When used with %NL80211_CMD_FRAME RX notification, indicates
+ * the incoming frame RX timestamp.
+ * @NL80211_ATTR_TD_BITMAP: Transition Disable bitmap, for subsequent
+ * (re)associations.
+ *
+ * @NL80211_ATTR_PUNCT_BITMAP: (u32) Preamble puncturing bitmap, lowest
+ * bit corresponds to the lowest 20 MHz channel. Each bit set to 1
+ * indicates that the sub-channel is punctured. Higher 16 bits are
+ * reserved.
+ *
+ * @NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS: Maximum number of peers that HW
+ * timestamping can be enabled for concurrently (u16), a wiphy attribute.
+ * A value of 0xffff indicates setting for all peers (i.e. not specifying
+ * an address with %NL80211_CMD_SET_HW_TIMESTAMP) is supported.
+ * @NL80211_ATTR_HW_TIMESTAMP_ENABLED: Indicates whether HW timestamping should
+ * be enabled or not (flag attribute).
+ *
+ * @NL80211_ATTR_EMA_RNR_ELEMS: Optional nested attribute for
+ * reduced neighbor report (RNR) elements. This attribute can be used
+ * only when NL80211_MBSSID_CONFIG_ATTR_EMA is enabled.
+ * Userspace is responsible for splitting the RNR into multiple
+ * elements such that each element excludes the non-transmitting
+ * profiles already included in the MBSSID element
+ * (%NL80211_ATTR_MBSSID_ELEMS) at the same index. Each EMA beacon
+ * will be generated by adding MBSSID and RNR elements at the same
+ * index. If the userspace includes more RNR elements than number of
+ * MBSSID elements then these will be added in every EMA beacon.
+ *
+ * @NL80211_ATTR_MLO_LINK_DISABLED: Flag attribute indicating that the link is
+ * disabled.
+ *
+ * @NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA: Include BSS usage data, i.e.
+ * include BSSes that can only be used in restricted scenarios and/or
+ * cannot be used at all.
+ *
+ * @NL80211_ATTR_MLO_TTLM_DLINK: Binary attribute specifying the downlink TID to
+ * link mapping. The length is 8 * sizeof(u16). For each TID the link
+ * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ * in Draft P802.11be_D4.0.
+ * @NL80211_ATTR_MLO_TTLM_ULINK: Binary attribute specifying the uplink TID to
+ * link mapping. The length is 8 * sizeof(u16). For each TID the link
+ * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ * in Draft P802.11be_D4.0.
+ *
+ * @NL80211_ATTR_ASSOC_SPP_AMSDU: flag attribute used with
+ * %NL80211_CMD_ASSOCIATE indicating the SPP A-MSDUs
+ * are used on this connection
+ *