Any comment about the usage of cmake is welcome.
+
+
CONFIGURING SARG
It is recommended to build sarg out of the source directory. It makes it easier
to delete the build directory completely and restart the configuration from
-scratch if the first attempt doesn't produce the expected result. To do so,
-create a directory at the same level as the sources of sarg and cd into that
-directory.
+scratch if the first attempt doesn't produce the expected result.
+
+If you intent to use both cmake and the autotools, then you MUST build sarg out
+of the source directory as it will overwrite the original stub config.h in the
+source directory and you won't be able to use the autotools afterward.
-Configure sarg with the command
+To build sarg out of source, create a build directory and cd into that directory.
+For instance, assuming your prompt is in the source directory, run
- ccmake ../sarg
+ mkdir build
+ cd build
+
+Configure sarg with the command (assuming the case of a build directory one level
+below the sources of sarg):
+
+ ccmake ..
On the first run, it will report that the cache is empty. Press 'c' to configure
the cache. Then ccmake will display an interface to select some configuration
make install
+
+
CONFIGURATION VARIABLES
These configuration variables are available on the first configuration run.
IMAGEDIR - The directory containing the images to use in the reports.
default: share/sarg/images
+ SARGPHPDIR - The directory to install sarg-php.
+ default: share/sarg/sarg-php
+
+ ENABLE_EXTRA_PROTECT - Compile sarg with some GCC options to increase the
+ security (tolerate no compilation warning, use the stack smashing
+ protection, improved printf check, and so on).
+ default: use standard warnings and no protection.
+
These variables are initialized with the values of the above variables and are
available on the second run.
IMAGEDIR_SOURCE - The full path to the images to compile in sarg.
default: CMAKE_INSTALL_PREFIX/IMAGEDIR
-They are other configuration variables whose documentation is visible during the
+There are other configuration variables whose documentation is visible during the
configuration with ccmake.
+
+
+
+COMPILATION WITH MSYS+MINGW
+
+The autotools don't compile sarg with msys. You have to use cmake in an msys
+terminal.
+
+If cmake is not already installed on your system, download and uncompress the
+cmake sources in your home directory then run the following commands in an msys
+terminal:
+
+ configure
+ make
+ make install
+
+Permanently add the path to cmake.exe by appending this line at the end of your
+profile file (c:/msys/1.0/etc/profile):
+
+ export PATH="$PATH:/c/Program files/CMake/bin"
+
+Reopen the msys terminal or run the above command in the same terminal to
+register the new path.
+
+Get the sources of sarg and uncompress them in your home directory. Let's assume
+they are in a directory named "sarg".
+
+Create a separate build directory and change to that directory. For instance,
+assuming your prompt is in the sarg directory, run the following commands:
+
+ mkdir build
+ cd build
+
+Configure, compile and install sarg:
+
+ cmake .. -G "MSYS Makefiles"
+ make
+ make install
+
+This will compile sarg outside of the sources and install it in c:\Program
+Files\sarg.
+
+If the compilation fails because mkstemp cannot be found, ensure that the LIB
+and INCLUDE environment variables are set properly to the lib and include
+directories of mingw. For instance, type the following two commands and run make
+again:
+
+ export LIB=c:/mingw/lib
+ export INCLUDE=c:/mingw/include
+
+You can make them permanent by appending those two commands at the end of the
+profile file in c:/msys/1.0/etc/profile.
+
+
+
+
+CONFIGURING SARG TO RUN ON WINDOWS
+
+Cmake install a sample configuration file in c:/Program
+Files/sarg/etc/sarg/sarg.conf.exemple. Rename it as sarg.conf and edit it.
+
+You must change the following options:
+
+ access_log c:/Program Files/sarg/log/access.log
+ temporary_dir c:/Program Files/sarg/tmp
+ output_dir c:/Program Files/sarg/www/squid-reports
+
+Adjust and create the directories according to your configuration.
+
+You may have to adjust other options to suit your needs.
+
+If sarg complains about a missing sort command, then you have to install
+the unxtools or run sarg from msys.
+
+If you want to run sarg from a regular dos prompt, download UnxUtils.zip from
+http://unxutils.sourceforge.net/ and uncompress it somewhere. Change the system
+path to include the usr\local\wbin directory before the Windows system
+directory.
+
+You must be sure that the unxutils are found before the windows native commands.
+To check this, open a dos prompt and type
+
+ls
+
+If it list the content of the directory, then the unxutils are found. Then type
+
+sort --help
+
+It should display the help of the sort command if the unxutils command is found
+first. If the windows command is found first, it will complain that the --help
+file cannot be found.
+
+Finally, if sort complains that it cannot write in the /tmp directory, either
+create that directory or set TMPDIR like this:
+
+ set TMPDIR=c:/Program Files/sarg/tmp
+
+It may be set to your TMP or TEMP directory or the temporary directory you named
+in your sarg.conf file.
projects / thirdparty / sarg.git / blobdiff