* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
* Copyright 2015-2017 Intel Deutschland GmbH
- * Copyright (C) 2018-2019 Intel Corporation
+ * Copyright (C) 2018-2024 Intel Corporation
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
* and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
* - a setup station entry is added, not yet authorized, without any rate
- * or capability information, this just exists to avoid race conditions
+ * or capability information; this just exists to avoid race conditions
* - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
* to add rate and capability information to the station and at the same
* time mark it authorized.
* DOC: Frame transmission/registration support
*
* Frame transmission and registration support exists to allow userspace
- * management entities such as wpa_supplicant react to management frames
+ * management entities such as wpa_supplicant to react to management frames
* that are not being handled by the kernel. This includes, for example,
* certain classes of action frames that cannot be handled in the kernel
* for various reasons.
*
* Frame transmission allows userspace to send for example the required
* responses to action frames. It is subject to some sanity checking,
- * but many frames can be transmitted. When a frame was transmitted, its
+ * but many frames can be transmitted. When a frame is transmitted, its
* status is indicated to the sending socket.
*
* For more technical details, see the corresponding command descriptions
/**
* DOC: Virtual interface / concurrency capabilities
*
- * Some devices are able to operate with virtual MACs, they can have
+ * Some devices are able to operate with virtual MACs; they can have
* more than one virtual interface. The capability handling for this
* is a bit complex though, as there may be a number of restrictions
* on the types of concurrency that are supported.
* Once concurrency is desired, more attributes must be observed:
* To start with, since some interface types are purely managed in
* software, like the AP-VLAN type in mac80211 for example, there's
- * an additional list of these, they can be added at any time and
+ * an additional list of these; they can be added at any time and
* are only restricted by some semantic restrictions (e.g. AP-VLAN
* cannot be added without a corresponding AP interface). This list
* is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
* Packet coalesce feature helps to reduce number of received interrupts
* to host by buffering these packets in firmware/hardware for some
* predefined time. Received interrupt will be generated when one of the
- * following events occur.
+ * following events occurs.
* a) Expiration of hardware timer whose expiration time is set to maximum
* coalescing delay of matching coalesce rule.
- * b) Coalescing buffer in hardware reaches it's limit.
+ * b) Coalescing buffer in hardware reaches its limit.
* c) Packet doesn't match any of the configured coalesce rules.
*
* User needs to configure following parameters for creating a coalesce
* rule.
* a) Maximum coalescing delay
* b) List of packet patterns which needs to be matched
- * c) Condition for coalescence. pattern 'match' or 'no match'
+ * c) Condition for coalescence: pattern 'match' or 'no match'
* Multiple such rules can be created.
*/
*
* By setting @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag drivers
* can indicate they support offloading EAPOL handshakes for WPA/WPA2
- * preshared key authentication. In %NL80211_CMD_CONNECT the preshared
- * key should be specified using %NL80211_ATTR_PMK. Drivers supporting
- * this offload may reject the %NL80211_CMD_CONNECT when no preshared
- * key material is provided, for example when that driver does not
- * support setting the temporal keys through %CMD_NEW_KEY.
+ * preshared key authentication in station mode. In %NL80211_CMD_CONNECT
+ * the preshared key should be specified using %NL80211_ATTR_PMK. Drivers
+ * supporting this offload may reject the %NL80211_CMD_CONNECT when no
+ * preshared key material is provided, for example when that driver does
+ * not support setting the temporal keys through %NL80211_CMD_NEW_KEY.
*
* Similarly @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X flag can be
* set by drivers indicating offload support of the PTK/GTK EAPOL
- * handshakes during 802.1X authentication. In order to use the offload
- * the %NL80211_CMD_CONNECT should have %NL80211_ATTR_WANT_1X_4WAY_HS
- * attribute flag. Drivers supporting this offload may reject the
- * %NL80211_CMD_CONNECT when the attribute flag is not present.
+ * handshakes during 802.1X authentication in station mode. In order to
+ * use the offload the %NL80211_CMD_CONNECT should have
+ * %NL80211_ATTR_WANT_1X_4WAY_HS attribute flag. Drivers supporting this
+ * offload may reject the %NL80211_CMD_CONNECT when the attribute flag is
+ * not present.
+ *
+ * By setting @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK flag drivers
+ * can indicate they support offloading EAPOL handshakes for WPA/WPA2
+ * preshared key authentication in AP mode. In %NL80211_CMD_START_AP
+ * the preshared key should be specified using %NL80211_ATTR_PMK. Drivers
+ * supporting this offload may reject the %NL80211_CMD_START_AP when no
+ * preshared key material is provided, for example when that driver does
+ * not support setting the temporal keys through %NL80211_CMD_NEW_KEY.
*
* For 802.1X the PMK or PMK-R0 are set by providing %NL80211_ATTR_PMK
* using %NL80211_CMD_SET_PMK. For offloaded FT support also
/**
* DOC: FILS shared key authentication offload
*
- * FILS shared key authentication offload can be advertized by drivers by
+ * FILS shared key authentication offload can be advertised by drivers by
* setting @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD flag. The drivers that support
* FILS shared key authentication offload should be able to construct the
* authentication and association frames for FILS shared key authentication and
* The PMKSA can be maintained in userspace persistently so that it can be used
* later after reboots or wifi turn off/on also.
*
- * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertized by a FILS
+ * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertised by a FILS
* capable AP supporting PMK caching. It specifies the scope within which the
* PMKSAs are cached in an ESS. %NL80211_CMD_SET_PMKSA and
* %NL80211_CMD_DEL_PMKSA are enhanced to allow support for PMKSA caching based
* DOC: SAE authentication offload
*
* By setting @NL80211_EXT_FEATURE_SAE_OFFLOAD flag drivers can indicate they
- * support offloading SAE authentication for WPA3-Personal networks. In
- * %NL80211_CMD_CONNECT the password for SAE should be specified using
- * %NL80211_ATTR_SAE_PASSWORD.
+ * support offloading SAE authentication for WPA3-Personal networks in station
+ * mode. Similarly @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP flag can be set by
+ * drivers indicating the offload support in AP mode.
+ *
+ * The password for SAE should be specified using %NL80211_ATTR_SAE_PASSWORD in
+ * %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP for station and AP mode
+ * respectively.
+ */
+
+/**
+ * DOC: VLAN offload support for setting group keys and binding STAs to VLANs
+ *
+ * By setting @NL80211_EXT_FEATURE_VLAN_OFFLOAD flag drivers can indicate they
+ * support offloading VLAN functionality in a manner where the driver exposes a
+ * single netdev that uses VLAN tagged frames and separate VLAN-specific netdevs
+ * can then be added using RTM_NEWLINK/IFLA_VLAN_ID similarly to the Ethernet
+ * case. Frames received from stations that are not assigned to any VLAN are
+ * delivered on the main netdev and frames to such stations can be sent through
+ * that main netdev.
+ *
+ * %NL80211_CMD_NEW_KEY (for group keys), %NL80211_CMD_NEW_STATION, and
+ * %NL80211_CMD_SET_STATION will optionally specify vlan_id using
+ * %NL80211_ATTR_VLAN_ID.
+ */
+
+/**
+ * DOC: TID configuration
+ *
+ * TID config support can be checked in the %NL80211_ATTR_TID_CONFIG
+ * attribute given in wiphy capabilities.
+ *
+ * The necessary configuration parameters are mentioned in
+ * &enum nl80211_tid_config_attr and it will be passed to the
+ * %NL80211_CMD_SET_TID_CONFIG command in %NL80211_ATTR_TID_CONFIG.
+ *
+ * If the configuration needs to be applied for specific peer then the MAC
+ * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
+ * configuration will be applied for all the connected peers in the vif except
+ * any peers that have peer-specific configuration for the TID by default; if
+ * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer-specific values
+ * will be overwritten.
+ *
+ * All this configuration is valid only for STA's current connection,
+ * i.e., the configuration will be reset to default when the STA connects back
+ * after disconnection/roaming, and this configuration will be cleared when
+ * the interface goes down.
+ */
+
+/**
+ * DOC: FILS shared key crypto offload
+ *
+ * This feature is applicable to drivers running in AP mode.
+ *
+ * FILS shared key crypto offload can be advertised by drivers by setting
+ * @NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD flag. The drivers that support
+ * FILS shared key crypto offload should be able to encrypt and decrypt
+ * association frames for FILS shared key authentication as per IEEE 802.11ai.
+ * With this capability, for FILS key derivation, drivers depend on userspace.
+ *
+ * After FILS key derivation, userspace shares the FILS AAD details with the
+ * driver and the driver stores the same to use in decryption of association
+ * request and in encryption of association response. The below parameters
+ * should be given to the driver in %NL80211_CMD_SET_FILS_AAD.
+ * %NL80211_ATTR_MAC - STA MAC address, used for storing FILS AAD per STA
+ * %NL80211_ATTR_FILS_KEK - Used for encryption or decryption
+ * %NL80211_ATTR_FILS_NONCES - Used for encryption or decryption
+ * (STA Nonce 16 bytes followed by AP Nonce 16 bytes)
+ *
+ * Once the association is done, the driver cleans the FILS AAD data.
+ */
+
+/**
+ * DOC: Multi-Link Operation
+ *
+ * In Multi-Link Operation, a connection between two MLDs utilizes multiple
+ * links. To use this in nl80211, various commands and responses now need
+ * to or will include the new %NL80211_ATTR_MLO_LINKS attribute.
+ * Additionally, various commands that need to operate on a specific link
+ * now need to be given the %NL80211_ATTR_MLO_LINK_ID attribute, e.g. to
+ * use %NL80211_CMD_START_AP or similar functions.
+ */
+
+/**
+ * DOC: OWE DH IE handling offload
+ *
+ * By setting @NL80211_EXT_FEATURE_OWE_OFFLOAD flag, drivers can indicate
+ * kernel/application space to avoid DH IE handling. When this flag is
+ * advertised, the driver/device will take care of DH IE inclusion and
+ * processing of peer DH IE to generate PMK.
*/
/**
* to get a list of all present wiphys.
* @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
* %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
- * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
- * attributes determining the channel width; this is used for setting
- * monitor mode channel), %NL80211_ATTR_WIPHY_RETRY_SHORT,
- * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
- * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
- * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
- * instead, the support here is for backward compatibility only.
+ * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
+ * %NL80211_ATTR_WIPHY_FREQ_OFFSET (and the attributes determining the
+ * channel width; this is used for setting monitor mode channel),
+ * %NL80211_ATTR_WIPHY_RETRY_SHORT, %NL80211_ATTR_WIPHY_RETRY_LONG,
+ * %NL80211_ATTR_WIPHY_FRAG_THRESHOLD, and/or
+ * %NL80211_ATTR_WIPHY_RTS_THRESHOLD. However, for setting the channel,
+ * see %NL80211_CMD_SET_CHANNEL instead, the support here is for backward
+ * compatibility only.
* @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
* or rename notification. Has attributes %NL80211_ATTR_WIPHY and
* %NL80211_ATTR_WIPHY_NAME.
* @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from
* userspace to request deletion of a virtual interface, then requires
- * attribute %NL80211_ATTR_IFINDEX.
+ * attribute %NL80211_ATTR_IFINDEX. If multiple BSSID advertisements are
+ * enabled using %NL80211_ATTR_MBSSID_CONFIG, %NL80211_ATTR_MBSSID_ELEMS,
+ * and if this command is used for the transmitting interface, then all
+ * the non-transmitting interfaces are deleted as well.
*
* @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
- * by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC.
+ * by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC. %NL80211_ATTR_MAC
+ * represents peer's MLD address for MLO pairwise key. For MLO group key,
+ * the link is identified by %NL80211_ATTR_MLO_LINK_ID.
* @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
* %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD.
+ * For MLO connection, the link to set default key is identified by
+ * %NL80211_ATTR_MLO_LINK_ID.
* @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
* %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER,
- * and %NL80211_ATTR_KEY_SEQ attributes.
+ * and %NL80211_ATTR_KEY_SEQ attributes. %NL80211_ATTR_MAC represents
+ * peer's MLD address for MLO pairwise key. The link to add MLO
+ * group key is identified by %NL80211_ATTR_MLO_LINK_ID.
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
- * or %NL80211_ATTR_MAC.
+ * or %NL80211_ATTR_MAC. %NL80211_ATTR_MAC represents peer's MLD address
+ * for MLO pairwise key. The link to delete group key is identified by
+ * %NL80211_ATTR_MLO_LINK_ID.
*
* @NL80211_CMD_GET_BEACON: (not used)
* @NL80211_CMD_SET_BEACON: change the beacon on an access point interface
* %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
* %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
* The channel to use can be set on the interface or be given using the
- * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
+ * %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_WIPHY_FREQ_OFFSET, and the
+ * attributes determining channel width.
* @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
* @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
* @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
* @NL80211_CMD_SET_STATION: Set station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_STATION: Add a station with given attributes to the
- * the interface identified by %NL80211_ATTR_IFINDEX.
+ * interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all stations, on the interface identified
- * by %NL80211_ATTR_IFINDEX. %NL80211_ATTR_MGMT_SUBTYPE and
+ * by %NL80211_ATTR_IFINDEX. For MLD station, MLD address is used in
+ * %NL80211_ATTR_MAC. %NL80211_ATTR_MGMT_SUBTYPE and
* %NL80211_ATTR_REASON_CODE can optionally be used to specify which type
* of disconnection indication should be sent to the station
* (Deauthentication or Disassociation frame and reason code for that
- * frame).
+ * frame). %NL80211_ATTR_MLO_LINK_ID can be used optionally to remove
+ * stations connected and using at least that link as one of its links.
*
* @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
* %NL80211_ATTR_MAC.
* @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
- * the interface identified by %NL80211_ATTR_IFINDEX.
+ * interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all mesh paths, on the interface identified
* by %NL80211_ATTR_IFINDEX.
* %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is
* not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified,
* scheduled scan will run in an infinite loop with the specified interval.
- * These attributes are mutually exculsive,
+ * These attributes are mutually exclusive,
* i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if
* NL80211_ATTR_SCHED_SCAN_PLANS is defined.
* If for some reason scheduled scan is aborted by the driver, all scan
* %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
* is brought down while a scheduled scan was running.
*
- * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
+ * @NL80211_CMD_GET_SURVEY: get survey results, e.g. channel occupation
* or noise level
* @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
* NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
* using %NL80211_ATTR_SSID, %NL80211_ATTR_FILS_CACHE_ID,
* %NL80211_ATTR_PMKID, and %NL80211_ATTR_PMK in case of FILS
* authentication where %NL80211_ATTR_FILS_CACHE_ID is the identifier
- * advertized by a FILS capable AP identifying the scope of PMKSA in an
+ * advertised by a FILS capable AP identifying the scope of PMKSA in an
* ESS.
* @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
* (for the BSSID) and %NL80211_ATTR_PMKID or using %NL80211_ATTR_SSID,
* %NL80211_ATTR_FILS_CACHE_ID, and %NL80211_ATTR_PMKID in case of FILS
- * authentication.
+ * authentication. Additionally in case of SAE offload and OWE offloads
+ * PMKSA entry can be deleted using %NL80211_ATTR_SSID.
* @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
*
* @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
* interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
* BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
* the SSID (mainly for association, but is included in authentication
- * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
- * to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
- * is used to specify the authentication type. %NL80211_ATTR_IE is used to
- * define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
- * to be added to the frame.
+ * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ +
+ * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequency of the
+ * channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the
+ * authentication type. %NL80211_ATTR_IE is used to define IEs
+ * (VendorSpecificInfo, but also including RSN IE and FT IEs) to be added
+ * to the frame.
* When used as an event, this reports reception of an Authentication
* frame in station and IBSS modes when the local MLME processed the
* frame, i.e., it was for the local STA and was received in correct
* requests to connect to a specified network but without separating
* auth and assoc steps. For this, you need to specify the SSID in a
* %NL80211_ATTR_SSID attribute, and can optionally specify the association
- * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP,
- * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE,
+ * %NL80211_ATTR_USE_MFP, %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ,
+ * %NL80211_ATTR_WIPHY_FREQ_OFFSET, %NL80211_ATTR_CONTROL_PORT,
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
* %NL80211_ATTR_CONTROL_PORT_OVER_NL80211, %NL80211_ATTR_MAC_HINT, and
* set of BSSID,frequency parameters is used (i.e., either the enforcing
* %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict
* %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT).
+ * Driver shall not modify the IEs specified through %NL80211_ATTR_IE if
+ * %NL80211_ATTR_MAC is included. However, if %NL80211_ATTR_MAC_HINT is
+ * included, these IEs through %NL80211_ATTR_IE are specified by the user
+ * space based on the best possible BSS selected. Thus, if the driver ends
+ * up selecting a different BSS, it can modify these IEs accordingly (e.g.
+ * userspace asks the driver to perform PMKSA caching with BSS1 and the
+ * driver ends up selecting BSS2 with different PMKSA cache entry; RSNIE
+ * has to get updated with the apt PMKID).
* %NL80211_ATTR_PREV_BSSID can be used to request a reassociation within
* the ESS in case the device is already associated and an association with
* a different BSS is desired.
* authentication/association or not receiving a response from the AP.
* Non-zero %NL80211_ATTR_STATUS_CODE value is indicated in that case as
* well to remain backwards compatible.
- * When establishing a security association, drivers that support 4 way
- * handshake offload should send %NL80211_CMD_PORT_AUTHORIZED event when
- * the 4 way handshake is completed successfully.
* @NL80211_CMD_ROAM: Notification indicating the card/driver roamed by itself.
- * When a security association was established with the new AP (e.g. if
- * the FT protocol was used for roaming or the driver completed the 4 way
- * handshake), this event should be followed by an
+ * When a security association was established on an 802.1X network using
+ * fast transition, this event should be followed by an
* %NL80211_CMD_PORT_AUTHORIZED event.
+ * Following a %NL80211_CMD_ROAM event userspace can issue
+ * %NL80211_CMD_GET_SCAN in order to obtain the scan information for the
+ * new BSS the card/driver roamed to.
* @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
* userspace that a connection was dropped by the AP or due to other
* reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
* four bytes for vendor frames including the OUI. The registration
* cannot be dropped, but is removed automatically when the netlink
* socket is closed. Multiple registrations can be made.
+ * The %NL80211_ATTR_RECEIVE_MULTICAST flag attribute can be given if
+ * %NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS is available, in which
+ * case the registration can also be modified to include/exclude the
+ * flag, rather than requiring unregistration to change it.
* @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
* backward compatibility
* @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
* %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA
* counters which will be updated to the current value. This attribute
* is used during CSA period.
+ * For TX on an MLD, the frequency can be omitted and the link ID be
+ * specified, or if transmitting to a known peer MLD (with MLD addresses
+ * in the frame) both can be omitted and the link will be selected by
+ * lower layers.
+ * For RX notification, %NL80211_ATTR_RX_HW_TIMESTAMP may be included to
+ * indicate the frame RX timestamp and %NL80211_ATTR_TX_HW_TIMESTAMP may
+ * be included to indicate the ack TX timestamp.
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary. This command is
* transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
* the TX command and %NL80211_ATTR_FRAME includes the contents of the
* frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
- * the frame.
+ * the frame. %NL80211_ATTR_TX_HW_TIMESTAMP may be included to indicate the
+ * tx timestamp and %NL80211_ATTR_RX_HW_TIMESTAMP may be included to
+ * indicate the ack RX timestamp.
* @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
* backward compatibility.
*
* reached.
* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
* and the attributes determining channel width) the given interface
- * (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
+ * (identified by %NL80211_ATTR_IFINDEX) shall operate on.
* In case multiple channels are supported by the device, the mechanism
* with which it switches channels is implementation-defined.
* When a monitor interface is given, it can only switch channel while
* of any other interfaces, and other interfaces will again take
* precedence when they are used.
*
- * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface
+ * (no longer supported).
*
* @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform
* multicast to unicast conversion. When enabled, all multicast packets
* various triggers. These triggers can be configured through this
* command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
* more background information, see
- * http://wireless.kernel.org/en/users/Documentation/WoWLAN.
+ * https://wireless.wiki.kernel.org/en/users/Documentation/WoWLAN.
* The @NL80211_CMD_SET_WOWLAN command can also be used as a notification
* from the driver reporting the wakeup reason. In this case, the
* @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
* inform userspace of the new replay counter.
*
* @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
- * of PMKSA caching dandidates.
+ * of PMKSA caching candidates.
*
* @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
* In addition, this can be used as an event to request userspace to take
*
* @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
* by sending a null data frame to it and reporting when the frame is
- * acknowleged. This is used to allow timing out inactive clients. Uses
+ * acknowledged. This is used to allow timing out inactive clients. Uses
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
* direct reply with an %NL80211_ATTR_COOKIE that is later used to match
* up the event with the request. The event includes the same data and
* @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
*
* @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
- * the new channel information (Channel Switch Announcement - CSA)
+ * new channel information (Channel Switch Announcement - CSA)
* in the beacon for some time (as defined in the
* %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
* new channel. Userspace provides the new channel information (using
* @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
* configured PMK for the authenticator address identified by
* %NL80211_ATTR_MAC.
- * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates that the 4 way
- * handshake was completed successfully by the driver. The BSSID is
- * specified with %NL80211_ATTR_MAC. Drivers that support 4 way handshake
- * offload should send this event after indicating 802.11 association with
- * %NL80211_CMD_CONNECT or %NL80211_CMD_ROAM. If the 4 way handshake failed
- * %NL80211_CMD_DISCONNECT should be indicated instead.
- *
+ * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates port is authorized and
+ * open for regular data traffic. For STA/P2P-client, this event is sent
+ * with AP MAC address and for AP/P2P-GO, the event carries the STA/P2P-
+ * client MAC address.
+ * Drivers that support 4 way handshake offload should send this event for
+ * STA/P2P-client after successful 4-way HS or after 802.1X FT following
+ * NL80211_CMD_CONNECT or NL80211_CMD_ROAM. Drivers using AP/P2P-GO 4-way
+ * handshake offload should send this event on successful completion of
+ * 4-way handshake with the peer (STA/P2P-client).
* @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
* and RX notification. This command is used both as a request to transmit
* a control port frame and as a notification that a control port frame
* has been received. %NL80211_ATTR_FRAME is used to specify the
* frame contents. The frame is the raw EAPoL data, without ethernet or
* 802.11 headers.
+ * For an MLD transmitter, the %NL80211_ATTR_MLO_LINK_ID may be given and
+ * its effect will depend on the destination: If the destination is known
+ * to be an MLD, this will be used as a hint to select the link to transmit
+ * the frame on. If the destination is not an MLD, this will select both
+ * the link to transmit on and the source address will be set to the link
+ * address of that link.
* When used as an event indication %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT and %NL80211_ATTR_MAC are added
* indicating the protocol type of the received frame; whether the frame
* %NL80211_ATTR_STATUS_CODE attribute in %NL80211_CMD_EXTERNAL_AUTH
* command interface.
*
+ * Host driver sends MLD address of the AP with %NL80211_ATTR_MLD_ADDR in
+ * %NL80211_CMD_EXTERNAL_AUTH event to indicate user space to enable MLO
+ * during the authentication offload in STA mode while connecting to MLD
+ * APs. Host driver should check %NL80211_ATTR_MLO_SUPPORT flag capability
+ * in %NL80211_CMD_CONNECT to know whether the user space supports enabling
+ * MLO during the authentication offload or not.
+ * User space should enable MLO during the authentication only when it
+ * receives the AP MLD address in authentication offload request. User
+ * space shouldn't enable MLO when the authentication offload request
+ * doesn't indicate the AP MLD address even if the AP is MLO capable.
+ * User space should use %NL80211_ATTR_MLD_ADDR as peer's MLD address and
+ * interface address identified by %NL80211_ATTR_IFINDEX as self MLD
+ * address. User space and host driver to use MLD addresses in RA, TA and
+ * BSSID fields of the frames between them, and host driver translates the
+ * MLD addresses to/from link addresses based on the link chosen for the
+ * authentication.
+ *
* Host driver reports this status on an authentication failure to the
* user space through the connect result as the user space would have
* initiated the connection through the connect request.
* randomization may be enabled and configured by specifying the
* %NL80211_ATTR_MAC and %NL80211_ATTR_MAC_MASK attributes.
* If a timeout is requested, use the %NL80211_ATTR_TIMEOUT attribute.
- * A u64 cookie for further %NL80211_ATTR_COOKIE use is is returned in
+ * A u64 cookie for further %NL80211_ATTR_COOKIE use is returned in
* the netlink extended ack message.
*
* To cancel a measurement, close the socket that requested it.
* peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
* content. The frame is ethernet data.
*
+ * @NL80211_CMD_SET_TID_CONFIG: Data frame TID specific configuration
+ * is passed using %NL80211_ATTR_TID_CONFIG attribute.
+ *
+ * @NL80211_CMD_UNPROT_BEACON: Unprotected or incorrectly protected Beacon
+ * frame. This event is used to indicate that a received Beacon frame was
+ * dropped because it did not include a valid MME MIC while beacon
+ * protection was enabled (BIGTK configured in station mode).
+ *
+ * @NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS: Report TX status of a control
+ * port frame transmitted with %NL80211_CMD_CONTROL_PORT_FRAME.
+ * %NL80211_ATTR_COOKIE identifies the TX command and %NL80211_ATTR_FRAME
+ * includes the contents of the frame. %NL80211_ATTR_ACK flag is included
+ * if the recipient acknowledged the frame.
+ *
+ * @NL80211_CMD_SET_SAR_SPECS: SAR power limitation configuration is
+ * passed using %NL80211_ATTR_SAR_SPEC. %NL80211_ATTR_WIPHY is used to
+ * specify the wiphy index to be applied to.
+ *
+ * @NL80211_CMD_OBSS_COLOR_COLLISION: This notification is sent out whenever
+ * mac80211/drv detects a bss color collision.
+ *
+ * @NL80211_CMD_COLOR_CHANGE_REQUEST: This command is used to indicate that
+ * userspace wants to change the BSS color.
+ *
+ * @NL80211_CMD_COLOR_CHANGE_STARTED: Notify userland, that a color change has
+ * started
+ *
+ * @NL80211_CMD_COLOR_CHANGE_ABORTED: Notify userland, that the color change has
+ * been aborted
+ *
+ * @NL80211_CMD_COLOR_CHANGE_COMPLETED: Notify userland that the color change
+ * has completed
+ *
+ * @NL80211_CMD_SET_FILS_AAD: Set FILS AAD data to the driver using -
+ * &NL80211_ATTR_MAC - for STA MAC address
+ * &NL80211_ATTR_FILS_KEK - for KEK
+ * &NL80211_ATTR_FILS_NONCES - for FILS Nonces
+ * (STA Nonce 16 bytes followed by AP Nonce 16 bytes)
+ *
+ * @NL80211_CMD_ASSOC_COMEBACK: notification about an association
+ * temporal rejection with comeback. The event includes %NL80211_ATTR_MAC
+ * to describe the BSSID address of the AP and %NL80211_ATTR_TIMEOUT to
+ * specify the timeout value.
+ *
+ * @NL80211_CMD_ADD_LINK: Add a new link to an interface. The
+ * %NL80211_ATTR_MLO_LINK_ID attribute is used for the new link.
+ * @NL80211_CMD_REMOVE_LINK: Remove a link from an interface. This may come
+ * without %NL80211_ATTR_MLO_LINK_ID as an easy way to remove all links
+ * in preparation for e.g. roaming to a regular (non-MLO) AP.
+ *
+ * @NL80211_CMD_ADD_LINK_STA: Add a link to an MLD station
+ * @NL80211_CMD_MODIFY_LINK_STA: Modify a link of an MLD station
+ * @NL80211_CMD_REMOVE_LINK_STA: Remove a link of an MLD station
+ *
+ * @NL80211_CMD_SET_HW_TIMESTAMP: Enable/disable HW timestamping of Timing
+ * measurement and Fine timing measurement frames. If %NL80211_ATTR_MAC
+ * is included, enable/disable HW timestamping only for frames to/from the
+ * specified MAC address. Otherwise enable/disable HW timestamping for
+ * all TM/FTM frames (including ones that were enabled with specific MAC
+ * address). If %NL80211_ATTR_HW_TIMESTAMP_ENABLED is not included, disable
+ * HW timestamping.
+ * The number of peers that HW timestamping can be enabled for concurrently
+ * is indicated by %NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS.
+ *
+ * @NL80211_CMD_LINKS_REMOVED: Notify userspace about the removal of STA MLD
+ * setup links due to AP MLD removing the corresponding affiliated APs with
+ * Multi-Link reconfiguration. %NL80211_ATTR_MLO_LINKS is used to provide
+ * information about the removed STA MLD setup links.
+ *
+ * @NL80211_CMD_SET_TID_TO_LINK_MAPPING: Set the TID to Link Mapping for a
+ * non-AP MLD station. The %NL80211_ATTR_MLO_TTLM_DLINK and
+ * %NL80211_ATTR_MLO_TTLM_ULINK attributes are used to specify the
+ * TID to Link mapping for downlink/uplink traffic.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
NL80211_CMD_PROBE_MESH_LINK,
+ NL80211_CMD_SET_TID_CONFIG,
+
+ NL80211_CMD_UNPROT_BEACON,
+
+ NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS,
+
+ NL80211_CMD_SET_SAR_SPECS,
+
+ NL80211_CMD_OBSS_COLOR_COLLISION,
+
+ NL80211_CMD_COLOR_CHANGE_REQUEST,
+
+ NL80211_CMD_COLOR_CHANGE_STARTED,
+ NL80211_CMD_COLOR_CHANGE_ABORTED,
+ NL80211_CMD_COLOR_CHANGE_COMPLETED,
+
+ NL80211_CMD_SET_FILS_AAD,
+
+ NL80211_CMD_ASSOC_COMEBACK,
+
+ NL80211_CMD_ADD_LINK,
+ NL80211_CMD_REMOVE_LINK,
+
+ NL80211_CMD_ADD_LINK_STA,
+ NL80211_CMD_MODIFY_LINK_STA,
+ NL80211_CMD_REMOVE_LINK_STA,
+
+ NL80211_CMD_SET_HW_TIMESTAMP,
+
+ NL80211_CMD_LINKS_REMOVED,
+
+ NL80211_CMD_SET_TID_TO_LINK_MAPPING,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
* of &enum nl80211_chan_width, describing the channel width. See the
* documentation of the enum for more information.
* @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
- * channel, used for anything but 20 MHz bandwidth
+ * channel, used for anything but 20 MHz bandwidth. In S1G this is the
+ * operating channel center frequency.
* @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
* channel, used only for 80+80 MHz bandwidth
* @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
* rates as defined by IEEE 802.11 7.3.2.2 but without the length
* restriction (at most %NL80211_MAX_SUPP_RATES).
* @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station
- * to, or the AP interface the station was originally added to to.
+ * to, or the AP interface the station was originally added to.
* @NL80211_ATTR_STA_INFO: information about a station, part of station info
* given for %NL80211_CMD_GET_STATION, nested attribute containing
* info as possible, see &enum nl80211_sta_info.
* flag is included, then control port frames are sent over NL80211 instead
* using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is
* to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
- * flag.
+ * flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
+ * frames are not forwarded over the control port.
*
* @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
* We recommend using nested, driver-specific attributes within this.
* specify just a single bitrate, which is to be used for the beacon.
* The driver must also specify support for this with the extended
* features NL80211_EXT_FEATURE_BEACON_RATE_LEGACY,
- * NL80211_EXT_FEATURE_BEACON_RATE_HT and
- * NL80211_EXT_FEATURE_BEACON_RATE_VHT.
+ * NL80211_EXT_FEATURE_BEACON_RATE_HT,
+ * NL80211_EXT_FEATURE_BEACON_RATE_VHT and
+ * NL80211_EXT_FEATURE_BEACON_RATE_HE.
*
* @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
* at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
* bit. Depending on which antennas are selected in the bitmap, 802.11n
* drivers can derive which chainmasks to use (if all antennas belonging to
* a particular chain are disabled this chain should be disabled) and if
- * a chain has diversity antennas wether diversity should be used or not.
+ * a chain has diversity antennas whether diversity should be used or not.
* HT capabilities (STBC, TX Beamforming, Antenna selection) can be
* derived from the available chains after applying the antenna mask.
- * Non-802.11n drivers can derive wether to use diversity or not.
+ * Non-802.11n drivers can derive whether to use diversity or not.
* Drivers may reject configurations or RX/TX mask combinations they cannot
* support by returning -EINVAL.
*
* @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire
* probe-response frame. The DA field in the 802.11 header is zero-ed out,
* to be filled by the FW.
- * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
- * this feature. Currently, only supported in mac80211 drivers.
+ * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
+ * this feature during association. This is a flag attribute.
+ * Currently only supported in mac80211 drivers.
+ * @NL80211_ATTR_DISABLE_VHT: Force VHT capable interfaces to disable
+ * this feature during association. This is a flag attribute.
+ * Currently only supported in mac80211 drivers.
+ * @NL80211_ATTR_DISABLE_HE: Force HE capable interfaces to disable
+ * this feature during association. This is a flag attribute.
+ * Currently only supported in mac80211 drivers.
* @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the
* ATTR_HT_CAPABILITY to which attention should be paid.
* Currently, only mac80211 NICs support this feature.
* until the channel switch event.
* @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
* must be blocked on the current channel (before the channel switch
- * operation).
+ * operation). Also included in the channel switch started event if quiet
+ * was requested by the AP.
* @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
* for the time while performing a channel switch.
- * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel
- * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
- * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel
- * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP).
+ * @NL80211_ATTR_CNTDWN_OFFS_BEACON: An array of offsets (u16) to the channel
+ * switch or color change counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
+ * @NL80211_ATTR_CNTDWN_OFFS_PRESP: An array of offsets (u16) to the channel
+ * switch or color change counters in the probe response (%NL80211_ATTR_PROBE_RESP).
*
* @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
* As specified in the &enum nl80211_rxmgmt_flags.
* @NL80211_ATTR_STA_SUPPORTED_CHANNELS: array of supported channels.
*
* @NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES: array of supported
- * supported operating classes.
+ * operating classes.
*
* @NL80211_ATTR_HANDLE_DFS: A flag indicating whether user space
* controls DFS operation in IBSS mode. If the flag is included in
*
* @NL80211_ATTR_IFTYPE_EXT_CAPA: Nested attribute of the following attributes:
* %NL80211_ATTR_IFTYPE, %NL80211_ATTR_EXT_CAPA,
- * %NL80211_ATTR_EXT_CAPA_MASK, to specify the extended capabilities per
- * interface type.
+ * %NL80211_ATTR_EXT_CAPA_MASK, to specify the extended capabilities and
+ * other interface-type specific capabilities per interface type. For MLO,
+ * %NL80211_ATTR_EML_CAPABILITY and %NL80211_ATTR_MLD_CAPA_AND_OPS are
+ * present.
*
* @NL80211_ATTR_MU_MIMO_GROUP_DATA: array of 24 bytes that defines a MU-MIMO
* groupID for monitor mode.
* from successful FILS authentication and is used with
* %NL80211_CMD_CONNECT.
*
- * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP
+ * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertised by a FILS AP
* identifying the scope of PMKSAs. This is used with
* @NL80211_CMD_SET_PMKSA and @NL80211_CMD_DEL_PMKSA.
*
* @NL80211_ATTR_PMK: attribute for passing PMK key material. Used with
* %NL80211_CMD_SET_PMKSA for the PMKSA identified by %NL80211_ATTR_PMKID.
- * For %NL80211_CMD_CONNECT it is used to provide PSK for offloading 4-way
- * handshake for WPA/WPA2-PSK networks. For 802.1X authentication it is
- * used with %NL80211_CMD_SET_PMK. For offloaded FT support this attribute
- * specifies the PMK-R0 if NL80211_ATTR_PMKR0_NAME is included as well.
+ * For %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP it is used to provide
+ * PSK for offloading 4-way handshake for WPA/WPA2-PSK networks. For 802.1X
+ * authentication it is used with %NL80211_CMD_SET_PMK. For offloaded FT
+ * support this attribute specifies the PMK-R0 if NL80211_ATTR_PMKR0_NAME
+ * is included as well.
*
* @NL80211_ATTR_SCHED_SCAN_MULTI: flag attribute which user-space shall use to
* indicate that it supports multiple active scheduled scan requests.
* space supports external authentication. This attribute shall be used
* with %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP request. The driver
* may offload authentication processing to user space if this capability
- * is indicated in the respective requests from the user space.
+ * is indicated in the respective requests from the user space. (This flag
+ * attribute deprecated for %NL80211_CMD_START_AP, use
+ * %NL80211_ATTR_AP_SETTINGS_FLAGS)
*
* @NL80211_ATTR_NSS: Station's New/updated RX_NSS value notified using this
* u8 attribute. This is used with %NL80211_CMD_STA_OPMODE_CHANGED.
* nl80211_txq_stats)
* @NL80211_ATTR_TXQ_LIMIT: Total packet limit for the TXQ queues for this phy.
* The smaller of this and the memory limit is enforced.
- * @NL80211_ATTR_TXQ_MEMORY_LIMIT: Total memory memory limit (in bytes) for the
+ * @NL80211_ATTR_TXQ_MEMORY_LIMIT: Total memory limit (in bytes) for the
* TXQ queues for this phy. The smaller of this and the packet limit is
* enforced.
* @NL80211_ATTR_TXQ_QUANTUM: TXQ scheduler quantum (bytes). Number of bytes
* the allowed channel bandwidth configurations. (u8 attribute)
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
*
+ * @NL80211_ATTR_VLAN_ID: VLAN ID (1..4094) for the station and VLAN group key
+ * (u16).
+ *
+ * @NL80211_ATTR_HE_BSS_COLOR: nested attribute for BSS Color Settings.
+ *
+ * @NL80211_ATTR_IFTYPE_AKM_SUITES: nested array attribute, with each entry
+ * using attributes from &enum nl80211_iftype_akm_attributes. This
+ * attribute is sent in a response to %NL80211_CMD_GET_WIPHY indicating
+ * supported AKM suites capability per interface. AKMs advertised in
+ * %NL80211_ATTR_AKM_SUITES are default capabilities if AKM suites not
+ * advertised for a specific interface type.
+ *
+ * @NL80211_ATTR_TID_CONFIG: TID specific configuration in a
+ * nested attribute with &enum nl80211_tid_config_attr sub-attributes;
+ * on output (in wiphy attributes) it contains only the feature sub-
+ * attributes.
+ *
+ * @NL80211_ATTR_CONTROL_PORT_NO_PREAUTH: disable preauth frame rx on control
+ * port in order to forward/receive them as ordinary data frames.
+ *
+ * @NL80211_ATTR_PMK_LIFETIME: Maximum lifetime for PMKSA in seconds (u32,
+ * dot11RSNAConfigPMKReauthThreshold; 0 is not a valid value).
+ * An optional parameter configured through %NL80211_CMD_SET_PMKSA.
+ * Drivers that trigger roaming need to know the lifetime of the
+ * configured PMKSA for triggering the full vs. PMKSA caching based
+ * authentication. This timeout helps authentication methods like SAE,
+ * where PMK gets updated only by going through a full (new SAE)
+ * authentication instead of getting updated during an association for EAP
+ * authentication. No new full authentication within the PMK expiry shall
+ * result in a disassociation at the end of the lifetime.
+ *
+ * @NL80211_ATTR_PMK_REAUTH_THRESHOLD: Reauthentication threshold time, in
+ * terms of percentage of %NL80211_ATTR_PMK_LIFETIME
+ * (u8, dot11RSNAConfigPMKReauthThreshold, 1..100). This is an optional
+ * parameter configured through %NL80211_CMD_SET_PMKSA. Requests the
+ * driver to trigger a full authentication roam (without PMKSA caching)
+ * after the reauthentication threshold time, but before the PMK lifetime
+ * has expired.
+ *
+ * Authentication methods like SAE need to be able to generate a new PMKSA
+ * entry without having to force a disconnection after the PMK timeout. If
+ * no roaming occurs between the reauth threshold and PMK expiration,
+ * disassociation is still forced.
+ * @NL80211_ATTR_RECEIVE_MULTICAST: multicast flag for the
+ * %NL80211_CMD_REGISTER_FRAME command, see the description there.
+ * @NL80211_ATTR_WIPHY_FREQ_OFFSET: offset of the associated
+ * %NL80211_ATTR_WIPHY_FREQ in positive KHz. Only valid when supplied with
+ * an %NL80211_ATTR_WIPHY_FREQ_OFFSET.
+ * @NL80211_ATTR_CENTER_FREQ1_OFFSET: Center frequency offset in KHz for the
+ * first channel segment specified in %NL80211_ATTR_CENTER_FREQ1.
+ * @NL80211_ATTR_SCAN_FREQ_KHZ: nested attribute with KHz frequencies
+ *
+ * @NL80211_ATTR_HE_6GHZ_CAPABILITY: HE 6 GHz Band Capability element (from
+ * association request when used with NL80211_CMD_NEW_STATION).
+ *
+ * @NL80211_ATTR_FILS_DISCOVERY: Optional parameter to configure FILS
+ * discovery. It is a nested attribute, see
+ * &enum nl80211_fils_discovery_attributes. Userspace should pass an empty
+ * nested attribute to disable this feature and delete the templates.
+ *
+ * @NL80211_ATTR_UNSOL_BCAST_PROBE_RESP: Optional parameter to configure
+ * unsolicited broadcast probe response. It is a nested attribute, see
+ * &enum nl80211_unsol_bcast_probe_resp_attributes. Userspace should pass an empty
+ * nested attribute to disable this feature and delete the templates.
+ *
+ * @NL80211_ATTR_S1G_CAPABILITY: S1G Capability information element (from
+ * association request when used with NL80211_CMD_NEW_STATION)
+ * @NL80211_ATTR_S1G_CAPABILITY_MASK: S1G Capability Information element
+ * override mask. Used with NL80211_ATTR_S1G_CAPABILITY in
+ * NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT.
+ *
+ * @NL80211_ATTR_SAE_PWE: Indicates the mechanism(s) allowed for SAE PWE
+ * derivation in WPA3-Personal networks which are using SAE authentication.
+ * This is a u8 attribute that encapsulates one of the values from
+ * &enum nl80211_sae_pwe_mechanism.
+ *
+ * @NL80211_ATTR_SAR_SPEC: SAR power limitation specification when
+ * used with %NL80211_CMD_SET_SAR_SPECS. The message contains fields
+ * of %nl80211_sar_attrs which specifies the sar type and related
+ * sar specs. Sar specs contains array of %nl80211_sar_specs_attrs.
+ *
+ * @NL80211_ATTR_RECONNECT_REQUESTED: flag attribute, used with deauth and
+ * disassoc events to indicate that an immediate reconnect to the AP
+ * is desired.
+ *
+ * @NL80211_ATTR_OBSS_COLOR_BITMAP: bitmap of the u64 BSS colors for the
+ * %NL80211_CMD_OBSS_COLOR_COLLISION event.
+ *
+ * @NL80211_ATTR_COLOR_CHANGE_COUNT: u8 attribute specifying the number of TBTT's
+ * until the color switch event.
+ * @NL80211_ATTR_COLOR_CHANGE_COLOR: u8 attribute specifying the color that we are
+ * switching to
+ * @NL80211_ATTR_COLOR_CHANGE_ELEMS: Nested set of attributes containing the IE
+ * information for the time while performing a color switch.
+ *
+ * @NL80211_ATTR_MBSSID_CONFIG: Nested attribute for multiple BSSID
+ * advertisements (MBSSID) parameters in AP mode.
+ * Kernel uses this attribute to indicate the driver's support for MBSSID
+ * and enhanced multi-BSSID advertisements (EMA AP) to the userspace.
+ * Userspace should use this attribute to configure per interface MBSSID
+ * parameters.
+ * See &enum nl80211_mbssid_config_attributes for details.
+ *
+ * @NL80211_ATTR_MBSSID_ELEMS: Nested parameter to pass multiple BSSID elements.
+ * Mandatory parameter for the transmitting interface to enable MBSSID.
+ * Optional for the non-transmitting interfaces.
+ *
+ * @NL80211_ATTR_RADAR_BACKGROUND: Configure dedicated offchannel chain
+ * available for radar/CAC detection on some hw. This chain can't be used
+ * to transmit or receive frames and it is bounded to a running wdev.
+ * Background radar/CAC detection allows to avoid the CAC downtime
+ * switching on a different channel during CAC detection on the selected
+ * radar channel.
+ *
+ * @NL80211_ATTR_AP_SETTINGS_FLAGS: u32 attribute contains ap settings flags,
+ * enumerated in &enum nl80211_ap_settings_flags. This attribute shall be
+ * used with %NL80211_CMD_START_AP request.
+ *
+ * @NL80211_ATTR_EHT_CAPABILITY: EHT Capability information element (from
+ * association request when used with NL80211_CMD_NEW_STATION). Can be set
+ * only if %NL80211_STA_FLAG_WME is set.
+ *
+ * @NL80211_ATTR_MLO_LINK_ID: A (u8) link ID for use with MLO, to be used with
+ * various commands that need a link ID to operate.
+ * @NL80211_ATTR_MLO_LINKS: A nested array of links, each containing some
+ * per-link information and a link ID.
+ * @NL80211_ATTR_MLD_ADDR: An MLD address, used with various commands such as
+ * authenticate/associate.
+ *
+ * @NL80211_ATTR_MLO_SUPPORT: Flag attribute to indicate user space supports MLO
+ * connection. Used with %NL80211_CMD_CONNECT. If this attribute is not
+ * included in NL80211_CMD_CONNECT drivers must not perform MLO connection.
+ *
+ * @NL80211_ATTR_MAX_NUM_AKM_SUITES: U16 attribute. Indicates maximum number of
+ * AKM suites allowed for %NL80211_CMD_CONNECT, %NL80211_CMD_ASSOCIATE and
+ * %NL80211_CMD_START_AP in %NL80211_CMD_GET_WIPHY response. If this
+ * attribute is not present userspace shall consider maximum number of AKM
+ * suites allowed as %NL80211_MAX_NR_AKM_SUITES which is the legacy maximum
+ * number prior to the introduction of this attribute.
+ *
+ * @NL80211_ATTR_EML_CAPABILITY: EML Capability information (u16)
+ * @NL80211_ATTR_MLD_CAPA_AND_OPS: MLD Capabilities and Operations (u16)
+ *
+ * @NL80211_ATTR_TX_HW_TIMESTAMP: Hardware timestamp for TX operation in
+ * nanoseconds (u64). This is the device clock timestamp so it will
+ * probably reset when the device is stopped or the firmware is reset.
+ * When used with %NL80211_CMD_FRAME_TX_STATUS, indicates the frame TX
+ * timestamp. When used with %NL80211_CMD_FRAME RX notification, indicates
+ * the ack TX timestamp.
+ * @NL80211_ATTR_RX_HW_TIMESTAMP: Hardware timestamp for RX operation in
+ * nanoseconds (u64). This is the device clock timestamp so it will
+ * probably reset when the device is stopped or the firmware is reset.
+ * When used with %NL80211_CMD_FRAME_TX_STATUS, indicates the ack RX
+ * timestamp. When used with %NL80211_CMD_FRAME RX notification, indicates
+ * the incoming frame RX timestamp.
+ * @NL80211_ATTR_TD_BITMAP: Transition Disable bitmap, for subsequent
+ * (re)associations.
+ *
+ * @NL80211_ATTR_PUNCT_BITMAP: (u32) Preamble puncturing bitmap, lowest
+ * bit corresponds to the lowest 20 MHz channel. Each bit set to 1
+ * indicates that the sub-channel is punctured. Higher 16 bits are
+ * reserved.
+ *
+ * @NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS: Maximum number of peers that HW
+ * timestamping can be enabled for concurrently (u16), a wiphy attribute.
+ * A value of 0xffff indicates setting for all peers (i.e. not specifying
+ * an address with %NL80211_CMD_SET_HW_TIMESTAMP) is supported.
+ * @NL80211_ATTR_HW_TIMESTAMP_ENABLED: Indicates whether HW timestamping should
+ * be enabled or not (flag attribute).
+ *
+ * @NL80211_ATTR_EMA_RNR_ELEMS: Optional nested attribute for
+ * reduced neighbor report (RNR) elements. This attribute can be used
+ * only when NL80211_MBSSID_CONFIG_ATTR_EMA is enabled.
+ * Userspace is responsible for splitting the RNR into multiple
+ * elements such that each element excludes the non-transmitting
+ * profiles already included in the MBSSID element
+ * (%NL80211_ATTR_MBSSID_ELEMS) at the same index. Each EMA beacon
+ * will be generated by adding MBSSID and RNR elements at the same
+ * index. If the userspace includes more RNR elements than number of
+ * MBSSID elements then these will be added in every EMA beacon.
+ *
+ * @NL80211_ATTR_MLO_LINK_DISABLED: Flag attribute indicating that the link is
+ * disabled.
+ *
+ * @NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA: Include BSS usage data, i.e.
+ * include BSSes that can only be used in restricted scenarios and/or
+ * cannot be used at all.
+ *
+ * @NL80211_ATTR_MLO_TTLM_DLINK: Binary attribute specifying the downlink TID to
+ * link mapping. The length is 8 * sizeof(u16). For each TID the link
+ * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ * in Draft P802.11be_D4.0.
+ * @NL80211_ATTR_MLO_TTLM_ULINK: Binary attribute specifying the uplink TID to
+ * link mapping. The length is 8 * sizeof(u16). For each TID the link
+ * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ * in Draft P802.11be_D4.0.
+ *
+ * @NL80211_ATTR_ASSOC_SPP_AMSDU: flag attribute used with
+ * %NL80211_CMD_ASSOCIATE indicating the SPP A-MSDUs
+ * are used on this connection
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
NL80211_ATTR_CH_SWITCH_COUNT,
NL80211_ATTR_CH_SWITCH_BLOCK_TX,
NL80211_ATTR_CSA_IES,
- NL80211_ATTR_CSA_C_OFF_BEACON,
- NL80211_ATTR_CSA_C_OFF_PRESP,
+ NL80211_ATTR_CNTDWN_OFFS_BEACON,
+ NL80211_ATTR_CNTDWN_OFFS_PRESP,
NL80211_ATTR_RXMGMT_FLAGS,
NL80211_ATTR_WIPHY_EDMG_CHANNELS,
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG,
+ NL80211_ATTR_VLAN_ID,
+
+ NL80211_ATTR_HE_BSS_COLOR,
+
+ NL80211_ATTR_IFTYPE_AKM_SUITES,
+
+ NL80211_ATTR_TID_CONFIG,
+
+ NL80211_ATTR_CONTROL_PORT_NO_PREAUTH,
+
+ NL80211_ATTR_PMK_LIFETIME,
+ NL80211_ATTR_PMK_REAUTH_THRESHOLD,
+
+ NL80211_ATTR_RECEIVE_MULTICAST,
+ NL80211_ATTR_WIPHY_FREQ_OFFSET,
+ NL80211_ATTR_CENTER_FREQ1_OFFSET,
+ NL80211_ATTR_SCAN_FREQ_KHZ,
+
+ NL80211_ATTR_HE_6GHZ_CAPABILITY,
+
+ NL80211_ATTR_FILS_DISCOVERY,
+
+ NL80211_ATTR_UNSOL_BCAST_PROBE_RESP,
+
+ NL80211_ATTR_S1G_CAPABILITY,
+ NL80211_ATTR_S1G_CAPABILITY_MASK,
+
+ NL80211_ATTR_SAE_PWE,
+
+ NL80211_ATTR_RECONNECT_REQUESTED,
+
+ NL80211_ATTR_SAR_SPEC,
+
+ NL80211_ATTR_DISABLE_HE,
+
+ NL80211_ATTR_OBSS_COLOR_BITMAP,
+
+ NL80211_ATTR_COLOR_CHANGE_COUNT,
+ NL80211_ATTR_COLOR_CHANGE_COLOR,
+ NL80211_ATTR_COLOR_CHANGE_ELEMS,
+
+ NL80211_ATTR_MBSSID_CONFIG,
+ NL80211_ATTR_MBSSID_ELEMS,
+
+ NL80211_ATTR_RADAR_BACKGROUND,
+
+ NL80211_ATTR_AP_SETTINGS_FLAGS,
+
+ NL80211_ATTR_EHT_CAPABILITY,
+
+ NL80211_ATTR_DISABLE_EHT,
+
+ NL80211_ATTR_MLO_LINKS,
+ NL80211_ATTR_MLO_LINK_ID,
+ NL80211_ATTR_MLD_ADDR,
+
+ NL80211_ATTR_MLO_SUPPORT,
+
+ NL80211_ATTR_MAX_NUM_AKM_SUITES,
+
+ NL80211_ATTR_EML_CAPABILITY,
+ NL80211_ATTR_MLD_CAPA_AND_OPS,
+
+ NL80211_ATTR_TX_HW_TIMESTAMP,
+ NL80211_ATTR_RX_HW_TIMESTAMP,
+ NL80211_ATTR_TD_BITMAP,
+
+ NL80211_ATTR_PUNCT_BITMAP,
+
+ NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS,
+ NL80211_ATTR_HW_TIMESTAMP_ENABLED,
+
+ NL80211_ATTR_EMA_RNR_ELEMS,
+
+ NL80211_ATTR_MLO_LINK_DISABLED,
+
+ NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA,
+
+ NL80211_ATTR_MLO_TTLM_DLINK,
+ NL80211_ATTR_MLO_TTLM_ULINK,
+
+ NL80211_ATTR_ASSOC_SPP_AMSDU,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
#define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
#define NL80211_ATTR_IFACE_SOCKET_OWNER NL80211_ATTR_SOCKET_OWNER
#define NL80211_ATTR_SAE_DATA NL80211_ATTR_AUTH_DATA
+#define NL80211_ATTR_CSA_C_OFF_BEACON NL80211_ATTR_CNTDWN_OFFS_BEACON
+#define NL80211_ATTR_CSA_C_OFF_PRESP NL80211_ATTR_CNTDWN_OFFS_PRESP
/*
* Allow user space programs to use #ifdef on new attributes by defining them
#define NL80211_HE_MIN_CAPABILITY_LEN 16
#define NL80211_HE_MAX_CAPABILITY_LEN 54
#define NL80211_MAX_NR_CIPHER_SUITES 5
+
+/*
+ * NL80211_MAX_NR_AKM_SUITES is obsolete when %NL80211_ATTR_MAX_NUM_AKM_SUITES
+ * present in %NL80211_CMD_GET_WIPHY response.
+ */
#define NL80211_MAX_NR_AKM_SUITES 2
+#define NL80211_EHT_MIN_CAPABILITY_LEN 13
+#define NL80211_EHT_MAX_CAPABILITY_LEN 51
#define NL80211_MIN_REMAIN_ON_CHANNEL_TIME 10
* and therefore can't be created in the normal ways, use the
* %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE
* commands to create and destroy one
- * @NL80211_IF_TYPE_OCB: Outside Context of a BSS
+ * @NL80211_IFTYPE_OCB: Outside Context of a BSS
* This mode corresponds to the MIB variable dot11OCBActivated=true
* @NL80211_IFTYPE_NAN: NAN device interface type (not a netdev)
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
* @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers
* that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a
* previously added station into associated state
+ * @NL80211_STA_FLAG_SPP_AMSDU: station supports SPP A-MSDUs
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
NL80211_STA_FLAG_AUTHENTICATED,
NL80211_STA_FLAG_TDLS_PEER,
NL80211_STA_FLAG_ASSOCIATED,
+ NL80211_STA_FLAG_SPP_AMSDU,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
NL80211_RATE_INFO_HE_GI_3_2,
};
+/**
+ * enum nl80211_he_ltf - HE long training field
+ * @NL80211_RATE_INFO_HE_1xLTF: 3.2 usec
+ * @NL80211_RATE_INFO_HE_2xLTF: 6.4 usec
+ * @NL80211_RATE_INFO_HE_4xLTF: 12.8 usec
+ */
+enum nl80211_he_ltf {
+ NL80211_RATE_INFO_HE_1XLTF,
+ NL80211_RATE_INFO_HE_2XLTF,
+ NL80211_RATE_INFO_HE_4XLTF,
+};
+
/**
* enum nl80211_he_ru_alloc - HE RU allocation values
* @NL80211_RATE_INFO_HE_RU_ALLOC_26: 26-tone RU allocation
NL80211_RATE_INFO_HE_RU_ALLOC_2x996,
};
+/**
+ * enum nl80211_eht_gi - EHT guard interval
+ * @NL80211_RATE_INFO_EHT_GI_0_8: 0.8 usec
+ * @NL80211_RATE_INFO_EHT_GI_1_6: 1.6 usec
+ * @NL80211_RATE_INFO_EHT_GI_3_2: 3.2 usec
+ */
+enum nl80211_eht_gi {
+ NL80211_RATE_INFO_EHT_GI_0_8,
+ NL80211_RATE_INFO_EHT_GI_1_6,
+ NL80211_RATE_INFO_EHT_GI_3_2,
+};
+
+/**
+ * enum nl80211_eht_ru_alloc - EHT RU allocation values
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_26: 26-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_52: 52-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_52P26: 52+26-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_106: 106-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_106P26: 106+26 tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_242: 242-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_484: 484-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_484P242: 484+242 tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_996: 996-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_996P484: 996+484 tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_996P484P242: 996+484+242 tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_2x996: 2x996-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_2x996P484: 2x996+484 tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_3x996: 3x996-tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_3x996P484: 3x996+484 tone RU allocation
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC_4x996: 4x996-tone RU allocation
+ */
+enum nl80211_eht_ru_alloc {
+ NL80211_RATE_INFO_EHT_RU_ALLOC_26,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_52,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_52P26,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_106,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_106P26,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_242,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_484,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_484P242,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_996,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_996P484,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_996P484P242,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_2x996,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_2x996P484,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_3x996,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_3x996P484,
+ NL80211_RATE_INFO_EHT_RU_ALLOC_4x996,
+};
+
/**
* enum nl80211_rate_info - bitrate information
*
* @NL80211_RATE_INFO_HE_DCM: HE DCM value (u8, 0/1)
* @NL80211_RATE_INFO_RU_ALLOC: HE RU allocation, if not present then
* non-OFDMA was used (u8, see &enum nl80211_he_ru_alloc)
+ * @NL80211_RATE_INFO_320_MHZ_WIDTH: 320 MHz bitrate
+ * @NL80211_RATE_INFO_EHT_MCS: EHT MCS index (u8, 0-15)
+ * @NL80211_RATE_INFO_EHT_NSS: EHT NSS value (u8, 1-8)
+ * @NL80211_RATE_INFO_EHT_GI: EHT guard interval identifier
+ * (u8, see &enum nl80211_eht_gi)
+ * @NL80211_RATE_INFO_EHT_RU_ALLOC: EHT RU allocation, if not present then
+ * non-OFDMA was used (u8, see &enum nl80211_eht_ru_alloc)
+ * @NL80211_RATE_INFO_S1G_MCS: S1G MCS index (u8, 0-10)
+ * @NL80211_RATE_INFO_S1G_NSS: S1G NSS value (u8, 1-4)
+ * @NL80211_RATE_INFO_1_MHZ_WIDTH: 1 MHz S1G rate
+ * @NL80211_RATE_INFO_2_MHZ_WIDTH: 2 MHz S1G rate
+ * @NL80211_RATE_INFO_4_MHZ_WIDTH: 4 MHz S1G rate
+ * @NL80211_RATE_INFO_8_MHZ_WIDTH: 8 MHz S1G rate
+ * @NL80211_RATE_INFO_16_MHZ_WIDTH: 16 MHz S1G rate
* @__NL80211_RATE_INFO_AFTER_LAST: internal use
*/
enum nl80211_rate_info {
NL80211_RATE_INFO_HE_GI,
NL80211_RATE_INFO_HE_DCM,
NL80211_RATE_INFO_HE_RU_ALLOC,
+ NL80211_RATE_INFO_320_MHZ_WIDTH,
+ NL80211_RATE_INFO_EHT_MCS,
+ NL80211_RATE_INFO_EHT_NSS,
+ NL80211_RATE_INFO_EHT_GI,
+ NL80211_RATE_INFO_EHT_RU_ALLOC,
+ NL80211_RATE_INFO_S1G_MCS,
+ NL80211_RATE_INFO_S1G_NSS,
+ NL80211_RATE_INFO_1_MHZ_WIDTH,
+ NL80211_RATE_INFO_2_MHZ_WIDTH,
+ NL80211_RATE_INFO_4_MHZ_WIDTH,
+ NL80211_RATE_INFO_8_MHZ_WIDTH,
+ NL80211_RATE_INFO_16_MHZ_WIDTH,
/* keep last */
__NL80211_RATE_INFO_AFTER_LAST,
* @NL80211_STA_INFO_AIRTIME_LINK_METRIC: airtime link metric for mesh station
* @NL80211_STA_INFO_ASSOC_AT_BOOTTIME: Timestamp (CLOCK_BOOTTIME, nanoseconds)
* of STA's association
+ * @NL80211_STA_INFO_CONNECTED_TO_AS: set to true if STA has a path to a
+ * authentication server (u8, 0 or 1)
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
NL80211_STA_INFO_AIRTIME_WEIGHT,
NL80211_STA_INFO_AIRTIME_LINK_METRIC,
NL80211_STA_INFO_ASSOC_AT_BOOTTIME,
+ NL80211_STA_INFO_CONNECTED_TO_AS,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
* capabilities IE
* @NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE: HE PPE thresholds information as
* defined in HE capabilities IE
- * @NL80211_BAND_IFTYPE_ATTR_MAX: highest band HE capability attribute currently
- * defined
+ * @NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA: HE 6GHz band capabilities (__le16),
+ * given for all 6 GHz band channels
+ * @NL80211_BAND_IFTYPE_ATTR_VENDOR_ELEMS: vendor element capabilities that are
+ * advertised on this band/for this iftype (binary)
+ * @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MAC: EHT MAC capabilities as in EHT
+ * capabilities element
+ * @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PHY: EHT PHY capabilities as in EHT
+ * capabilities element
+ * @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MCS_SET: EHT supported NSS/MCS as in EHT
+ * capabilities element
+ * @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PPE: EHT PPE thresholds information as
+ * defined in EHT capabilities element
* @__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST: internal use
+ * @NL80211_BAND_IFTYPE_ATTR_MAX: highest band attribute currently defined
*/
enum nl80211_band_iftype_attr {
__NL80211_BAND_IFTYPE_ATTR_INVALID,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_PHY,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE,
+ NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA,
+ NL80211_BAND_IFTYPE_ATTR_VENDOR_ELEMS,
+ NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MAC,
+ NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PHY,
+ NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MCS_SET,
+ NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PPE,
/* keep last */
__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST,
* @NL80211_BAND_ATTR_EDMG_BW_CONFIG: Channel BW Configuration subfield encodes
* the allowed channel bandwidth configurations.
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
+ * @NL80211_BAND_ATTR_S1G_MCS_NSS_SET: S1G capabilities, supported S1G-MCS and NSS
+ * set subfield, as in the S1G information IE, 5 bytes
+ * @NL80211_BAND_ATTR_S1G_CAPA: S1G capabilities information subfield as in the
+ * S1G information IE, 10 bytes
* @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
* @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
NL80211_BAND_ATTR_EDMG_CHANNELS,
NL80211_BAND_ATTR_EDMG_BW_CONFIG,
+ NL80211_BAND_ATTR_S1G_MCS_NSS_SET,
+ NL80211_BAND_ATTR_S1G_CAPA,
+
/* keep last */
__NL80211_BAND_ATTR_AFTER_LAST,
NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
* (100 * dBm).
* @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS
* (enum nl80211_dfs_state)
- * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long
+ * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in milliseconds for how long
* this channel is in this DFS state.
* @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
* channel as the control channel
* @NL80211_FREQUENCY_ATTR_WMM: this channel has wmm limitations.
* This is a nested attribute that contains the wmm limitation per AC.
* (see &enum nl80211_wmm_rule)
+ * @NL80211_FREQUENCY_ATTR_NO_HE: HE operation is not allowed on this channel
+ * in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_OFFSET: frequency offset in KHz
+ * @NL80211_FREQUENCY_ATTR_1MHZ: 1 MHz operation is allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_2MHZ: 2 MHz operation is allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_4MHZ: 4 MHz operation is allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_8MHZ: 8 MHz operation is allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_16MHZ: 16 MHz operation is allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_NO_320MHZ: any 320 MHz channel using this channel
+ * as the primary or any of the secondary channels isn't possible
+ * @NL80211_FREQUENCY_ATTR_NO_EHT: EHT operation is not allowed on this channel
+ * in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_PSD: Power spectral density (in dBm) that
+ * is allowed on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_DFS_CONCURRENT: Operation on this channel is
+ * allowed for peer-to-peer or adhoc communication under the control
+ * of a DFS master which operates on the same channel (FCC-594280 D01
+ * Section B.3). Should be used together with %NL80211_RRF_DFS only.
+ * @NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP
+ * not allowed using this channel
+ * @NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP
+ * not allowed using this channel
+ * @NL80211_FREQUENCY_ATTR_CAN_MONITOR: This channel can be used in monitor
+ * mode despite other (regulatory) restrictions, even if the channel is
+ * otherwise completely disabled.
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
* currently defined
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
NL80211_FREQUENCY_ATTR_NO_20MHZ,
NL80211_FREQUENCY_ATTR_NO_10MHZ,
NL80211_FREQUENCY_ATTR_WMM,
+ NL80211_FREQUENCY_ATTR_NO_HE,
+ NL80211_FREQUENCY_ATTR_OFFSET,
+ NL80211_FREQUENCY_ATTR_1MHZ,
+ NL80211_FREQUENCY_ATTR_2MHZ,
+ NL80211_FREQUENCY_ATTR_4MHZ,
+ NL80211_FREQUENCY_ATTR_8MHZ,
+ NL80211_FREQUENCY_ATTR_16MHZ,
+ NL80211_FREQUENCY_ATTR_NO_320MHZ,
+ NL80211_FREQUENCY_ATTR_NO_EHT,
+ NL80211_FREQUENCY_ATTR_PSD,
+ NL80211_FREQUENCY_ATTR_DFS_CONCURRENT,
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT,
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT,
+ NL80211_FREQUENCY_ATTR_CAN_MONITOR,
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
#define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR
#define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \
NL80211_FREQUENCY_ATTR_IR_CONCURRENT
+#define NL80211_FREQUENCY_ATTR_NO_UHB_VLP_CLIENT \
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT
+#define NL80211_FREQUENCY_ATTR_NO_UHB_AFC_CLIENT \
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT
/**
* enum nl80211_bitrate_attr - bitrate attributes
* a given frequency range. The value is in mBm (100 * dBm).
* @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
* If not present or 0 default CAC time will be used.
+ * @NL80211_ATTR_POWER_RULE_PSD: power spectral density (in dBm).
+ * This could be negative.
* @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
* currently defined
* @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
NL80211_ATTR_DFS_CAC_TIME,
+ NL80211_ATTR_POWER_RULE_PSD,
+
/* keep last */
__NL80211_REG_RULE_ATTR_AFTER_LAST,
NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
* value as specified by &struct nl80211_bss_select_rssi_adjust.
* @NL80211_SCHED_SCAN_MATCH_ATTR_BSSID: BSSID to be used for matching
* (this cannot be used together with SSID).
- * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the
- * band specific minimum rssi thresholds for the bands defined in
- * enum nl80211_band. The minimum rssi threshold value(s32) specific to a
- * band shall be encapsulated in attribute with type value equals to one
- * of the NL80211_BAND_* defined in enum nl80211_band. For example, the
- * minimum rssi threshold value for 2.4GHZ band shall be encapsulated
- * within an attribute of type NL80211_BAND_2GHZ. And one or more of such
- * attributes will be nested within this attribute.
+ * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Obsolete
* @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
* attribute number currently defined
* @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI,
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST,
NL80211_SCHED_SCAN_MATCH_ATTR_BSSID,
- NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI,
+ NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI, /* obsolete */
/* keep last */
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
* @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
* @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
* @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
+ * @NL80211_RRF_NO_HE: HE operation not allowed
+ * @NL80211_RRF_NO_320MHZ: 320MHz operation not allowed
+ * @NL80211_RRF_NO_EHT: EHT operation not allowed
+ * @NL80211_RRF_PSD: Ruleset has power spectral density value
+ * @NL80211_RRF_DFS_CONCURRENT: Operation on this channel is allowed for
+ peer-to-peer or adhoc communication under the control of a DFS master
+ which operates on the same channel (FCC-594280 D01 Section B.3).
+ Should be used together with %NL80211_RRF_DFS only.
+ * @NL80211_RRF_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP not allowed
+ * @NL80211_RRF_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP not allowed
*/
enum nl80211_reg_rule_flags {
NL80211_RRF_NO_OFDM = 1<<0,
NL80211_RRF_NO_HT40PLUS = 1<<14,
NL80211_RRF_NO_80MHZ = 1<<15,
NL80211_RRF_NO_160MHZ = 1<<16,
+ NL80211_RRF_NO_HE = 1<<17,
+ NL80211_RRF_NO_320MHZ = 1<<18,
+ NL80211_RRF_NO_EHT = 1<<19,
+ NL80211_RRF_PSD = 1<<20,
+ NL80211_RRF_DFS_CONCURRENT = 1<<21,
+ NL80211_RRF_NO_6GHZ_VLP_CLIENT = 1<<22,
+ NL80211_RRF_NO_6GHZ_AFC_CLIENT = 1<<23,
};
#define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR
#define NL80211_RRF_NO_HT40 (NL80211_RRF_NO_HT40MINUS |\
NL80211_RRF_NO_HT40PLUS)
#define NL80211_RRF_GO_CONCURRENT NL80211_RRF_IR_CONCURRENT
+#define NL80211_RRF_NO_UHB_VLP_CLIENT NL80211_RRF_NO_6GHZ_VLP_CLIENT
+#define NL80211_RRF_NO_UHB_AFC_CLIENT NL80211_RRF_NO_6GHZ_AFC_CLIENT
/* For backport compatibility with older userspace */
#define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
* receiving frames destined to the local BSS
* @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
* currently defined
+ * @NL80211_SURVEY_INFO_FREQUENCY_OFFSET: center frequency offset in KHz
* @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
*/
enum nl80211_survey_info {
NL80211_SURVEY_INFO_TIME_SCAN,
NL80211_SURVEY_INFO_PAD,
NL80211_SURVEY_INFO_TIME_BSS_RX,
+ NL80211_SURVEY_INFO_FREQUENCY_OFFSET,
/* keep last */
__NL80211_SURVEY_INFO_AFTER_LAST,
* field. If left unset then the mesh formation field will only
* advertise such if there is an active root mesh path.
*
+ * @NL80211_MESHCONF_NOLEARN: Try to avoid multi-hop path discovery (e.g.
+ * PREQ/PREP for HWMP) if the destination is a direct neighbor. Note that
+ * this might not be the optimal decision as a multi-hop route might be
+ * better. So if using this setting you will likely also want to disable
+ * dot11MeshForwarding and use another mesh routing protocol on top.
+ *
+ * @NL80211_MESHCONF_CONNECTED_TO_AS: If set to true then this mesh STA
+ * will advertise that it is connected to a authentication server
+ * in the mesh formation field.
+ *
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
*/
enum nl80211_meshconf_params {
NL80211_MESHCONF_AWAKE_WINDOW,
NL80211_MESHCONF_PLINK_TIMEOUT,
NL80211_MESHCONF_CONNECTED_TO_GATE,
+ NL80211_MESHCONF_NOLEARN,
+ NL80211_MESHCONF_CONNECTED_TO_AS,
/* keep last */
__NL80211_MESHCONF_ATTR_AFTER_LAST,
* attribute must be provided as well
* @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel
* @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_1: 1 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_2: 2 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_4: 4 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_8: 8 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_16: 16 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_320: 320 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
+ * attribute must be provided as well
*/
enum nl80211_chan_width {
NL80211_CHAN_WIDTH_20_NOHT,
NL80211_CHAN_WIDTH_160,
NL80211_CHAN_WIDTH_5,
NL80211_CHAN_WIDTH_10,
+ NL80211_CHAN_WIDTH_1,
+ NL80211_CHAN_WIDTH_2,
+ NL80211_CHAN_WIDTH_4,
+ NL80211_CHAN_WIDTH_8,
+ NL80211_CHAN_WIDTH_16,
+ NL80211_CHAN_WIDTH_320,
};
/**
* @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
* @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
* @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
+ * @NL80211_BSS_CHAN_WIDTH_1: control channel is 1 MHz wide
+ * @NL80211_BSS_CHAN_WIDTH_2: control channel is 2 MHz wide
*/
enum nl80211_bss_scan_width {
NL80211_BSS_CHAN_WIDTH_20,
NL80211_BSS_CHAN_WIDTH_10,
NL80211_BSS_CHAN_WIDTH_5,
+ NL80211_BSS_CHAN_WIDTH_1,
+ NL80211_BSS_CHAN_WIDTH_2,
+};
+
+/**
+ * enum nl80211_bss_use_for - bitmap indicating possible BSS use
+ * @NL80211_BSS_USE_FOR_NORMAL: Use this BSS for normal "connection",
+ * including IBSS/MBSS depending on the type.
+ * @NL80211_BSS_USE_FOR_MLD_LINK: This BSS can be used as a link in an
+ * MLO connection. Note that for an MLO connection, all links including
+ * the assoc link must have this flag set, and the assoc link must
+ * additionally have %NL80211_BSS_USE_FOR_NORMAL set.
+ */
+enum nl80211_bss_use_for {
+ NL80211_BSS_USE_FOR_NORMAL = 1 << 0,
+ NL80211_BSS_USE_FOR_MLD_LINK = 1 << 1,
+};
+
+/**
+ * enum nl80211_bss_cannot_use_reasons - reason(s) connection to a
+ * BSS isn't possible
+ * @NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY: NSTR nonprimary links aren't
+ * supported by the device, and this BSS entry represents one.
+ * @NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH: STA is not supporting
+ * the AP power type (SP, VLP, AP) that the AP uses.
+ */
+enum nl80211_bss_cannot_use_reasons {
+ NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY = 1 << 0,
+ NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH = 1 << 1,
};
+#define NL80211_BSS_CANNOT_USE_UHB_PWR_MISMATCH \
+ NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH
+
/**
* enum nl80211_bss - netlink attributes for a BSS
*
* elements from a Beacon frame (bin); not present if no Beacon frame has
* yet been received
* @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
- * (u32, enum nl80211_bss_scan_width)
+ * (u32, enum nl80211_bss_scan_width) - No longer used!
* @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
* (not present if no beacon frame has been received yet)
* @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
* @NL80211_BSS_CHAIN_SIGNAL: per-chain signal strength of last BSS update.
* Contains a nested array of signal strength attributes (u8, dBm),
* using the nesting index as the antenna number.
+ * @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz
+ * @NL80211_BSS_MLO_LINK_ID: MLO link ID of the BSS (u8).
+ * @NL80211_BSS_MLD_ADDR: MLD address of this BSS if connected to it.
+ * @NL80211_BSS_USE_FOR: u32 bitmap attribute indicating what the BSS can be
+ * used for, see &enum nl80211_bss_use_for.
+ * @NL80211_BSS_CANNOT_USE_REASONS: Indicates the reason that this BSS cannot
+ * be used for all or some of the possible uses by the device reporting it,
+ * even though its presence was detected.
+ * This is a u64 attribute containing a bitmap of values from
+ * &enum nl80211_cannot_use_reasons, note that the attribute may be missing
+ * if no reasons are specified.
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
NL80211_BSS_PARENT_TSF,
NL80211_BSS_PARENT_BSSID,
NL80211_BSS_CHAIN_SIGNAL,
+ NL80211_BSS_FREQUENCY_OFFSET,
+ NL80211_BSS_MLO_LINK_ID,
+ NL80211_BSS_MLD_ADDR,
+ NL80211_BSS_USE_FOR,
+ NL80211_BSS_CANNOT_USE_REASONS,
/* keep last */
__NL80211_BSS_AFTER_LAST,
* See &enum nl80211_key_default_types.
* @NL80211_KEY_MODE: the mode from enum nl80211_key_mode.
* Defaults to @NL80211_KEY_RX_TX.
+ * @NL80211_KEY_DEFAULT_BEACON: flag indicating default Beacon frame key
*
* @__NL80211_KEY_AFTER_LAST: internal
* @NL80211_KEY_MAX: highest key attribute
NL80211_KEY_TYPE,
NL80211_KEY_DEFAULT_TYPES,
NL80211_KEY_MODE,
+ NL80211_KEY_DEFAULT_BEACON,
/* keep last */
__NL80211_KEY_AFTER_LAST,
* @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection,
* see &struct nl80211_txrate_vht
* @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi
+ * @NL80211_TXRATE_HE: HE rates allowed for TX rate selection,
+ * see &struct nl80211_txrate_he
+ * @NL80211_TXRATE_HE_GI: configure HE GI, 0.8us, 1.6us and 3.2us.
+ * @NL80211_TXRATE_HE_LTF: configure HE LTF, 1XLTF, 2XLTF and 4XLTF.
* @__NL80211_TXRATE_AFTER_LAST: internal
* @NL80211_TXRATE_MAX: highest TX rate attribute
*/
NL80211_TXRATE_HT,
NL80211_TXRATE_VHT,
NL80211_TXRATE_GI,
+ NL80211_TXRATE_HE,
+ NL80211_TXRATE_HE_GI,
+ NL80211_TXRATE_HE_LTF,
/* keep last */
__NL80211_TXRATE_AFTER_LAST,
__u16 mcs[NL80211_VHT_NSS_MAX];
};
+#define NL80211_HE_NSS_MAX 8
+/**
+ * struct nl80211_txrate_he - HE MCS/NSS txrate bitmap
+ * @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.)
+ */
+struct nl80211_txrate_he {
+ __u16 mcs[NL80211_HE_NSS_MAX];
+};
+
enum nl80211_txrate_gi {
NL80211_TXRATE_DEFAULT_GI,
NL80211_TXRATE_FORCE_SGI,
* @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
* @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 69.12 GHz)
* @NL80211_BAND_6GHZ: around 6 GHz band (5.9 - 7.2 GHz)
+ * @NL80211_BAND_S1GHZ: around 900MHz, supported by S1G PHYs
+ * @NL80211_BAND_LC: light communication band (placeholder)
* @NUM_NL80211_BANDS: number of bands, avoid using this in userspace
* since newer kernel versions may support more bands
*/
NL80211_BAND_5GHZ,
NL80211_BAND_60GHZ,
NL80211_BAND_6GHZ,
+ NL80211_BAND_S1GHZ,
+ NL80211_BAND_LC,
NUM_NL80211_BANDS,
};
NL80211_TX_POWER_FIXED,
};
+/**
+ * enum nl80211_tid_config - TID config state
+ * @NL80211_TID_CONFIG_ENABLE: Enable config for the TID
+ * @NL80211_TID_CONFIG_DISABLE: Disable config for the TID
+ */
+enum nl80211_tid_config {
+ NL80211_TID_CONFIG_ENABLE,
+ NL80211_TID_CONFIG_DISABLE,
+};
+
+/* enum nl80211_tx_rate_setting - TX rate configuration type
+ * @NL80211_TX_RATE_AUTOMATIC: automatically determine TX rate
+ * @NL80211_TX_RATE_LIMITED: limit the TX rate by the TX rate parameter
+ * @NL80211_TX_RATE_FIXED: fix TX rate to the TX rate parameter
+ */
+enum nl80211_tx_rate_setting {
+ NL80211_TX_RATE_AUTOMATIC,
+ NL80211_TX_RATE_LIMITED,
+ NL80211_TX_RATE_FIXED,
+};
+
+/* enum nl80211_tid_config_attr - TID specific configuration.
+ * @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
+ * @NL80211_TID_CONFIG_ATTR_VIF_SUPP: a bitmap (u64) of attributes supported
+ * for per-vif configuration; doesn't list the ones that are generic
+ * (%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
+ * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
+ * per peer instead.
+ * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribute, if set indicates
+ * that the new configuration overrides all previous peer
+ * configurations, otherwise previous peer specific configurations
+ * should be left untouched.
+ * @NL80211_TID_CONFIG_ATTR_TIDS: a bitmask value of TIDs (bit 0 to 7)
+ * Its type is u16.
+ * @NL80211_TID_CONFIG_ATTR_NOACK: Configure ack policy for the TID.
+ * specified in %NL80211_TID_CONFIG_ATTR_TID. see %enum nl80211_tid_config.
+ * Its type is u8.
+ * @NL80211_TID_CONFIG_ATTR_RETRY_SHORT: Number of retries used with data frame
+ * transmission, user-space sets this configuration in
+ * &NL80211_CMD_SET_TID_CONFIG. It is u8 type, min value is 1 and
+ * the max value is advertised by the driver in this attribute on
+ * output in wiphy capabilities.
+ * @NL80211_TID_CONFIG_ATTR_RETRY_LONG: Number of retries used with data frame
+ * transmission, user-space sets this configuration in
+ * &NL80211_CMD_SET_TID_CONFIG. Its type is u8, min value is 1 and
+ * the max value is advertised by the driver in this attribute on
+ * output in wiphy capabilities.
+ * @NL80211_TID_CONFIG_ATTR_AMPDU_CTRL: Enable/Disable MPDU aggregation
+ * for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
+ * Its type is u8, using the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL: Enable/Disable RTS_CTS for the TIDs
+ * specified in %NL80211_TID_CONFIG_ATTR_TIDS. It is u8 type, using
+ * the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_AMSDU_CTRL: Enable/Disable MSDU aggregation
+ * for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
+ * Its type is u8, using the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE: This attribute will be useful
+ * to notfiy the driver that what type of txrate should be used
+ * for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS. using
+ * the values form &nl80211_tx_rate_setting.
+ * @NL80211_TID_CONFIG_ATTR_TX_RATE: Data frame TX rate mask should be applied
+ * with the parameters passed through %NL80211_ATTR_TX_RATES.
+ * configuration is applied to the data frame for the tid to that connected
+ * station.
+ */
+enum nl80211_tid_config_attr {
+ __NL80211_TID_CONFIG_ATTR_INVALID,
+ NL80211_TID_CONFIG_ATTR_PAD,
+ NL80211_TID_CONFIG_ATTR_VIF_SUPP,
+ NL80211_TID_CONFIG_ATTR_PEER_SUPP,
+ NL80211_TID_CONFIG_ATTR_OVERRIDE,
+ NL80211_TID_CONFIG_ATTR_TIDS,
+ NL80211_TID_CONFIG_ATTR_NOACK,
+ NL80211_TID_CONFIG_ATTR_RETRY_SHORT,
+ NL80211_TID_CONFIG_ATTR_RETRY_LONG,
+ NL80211_TID_CONFIG_ATTR_AMPDU_CTRL,
+ NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL,
+ NL80211_TID_CONFIG_ATTR_AMSDU_CTRL,
+ NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE,
+ NL80211_TID_CONFIG_ATTR_TX_RATE,
+
+ /* keep last */
+ __NL80211_TID_CONFIG_ATTR_AFTER_LAST,
+ NL80211_TID_CONFIG_ATTR_MAX = __NL80211_TID_CONFIG_ATTR_AFTER_LAST - 1
+};
+
/**
* enum nl80211_packet_pattern_attr - packet pattern attribute
* @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
* %NL80211_ATTR_SCAN_FREQUENCIES contains more than one
* frequency, it means that the match occurred in more than one
* channel.
+ * @NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC: For wakeup reporting only.
+ * Wake up happened due to unprotected deauth or disassoc frame in MFP.
* @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
* @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
*
NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS,
NL80211_WOWLAN_TRIG_NET_DETECT,
NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS,
+ NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC,
/* keep last */
NUM_NL80211_WOWLAN_TRIG,
/**
* enum nl80211_coalesce_condition - coalesce rule conditions
- * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
+ * @NL80211_COALESCE_CONDITION_MATCH: coalesce Rx packets when patterns
* in a rule are matched.
* @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
* in a rule are not matched.
* => allows 8 of AP/GO that can have BI gcd >= min gcd
*
* numbers = [ #{STA} <= 2 ], channels = 2, max = 2
- * => allows two STAs on different channels
+ * => allows two STAs on the same or on different channels
*
* numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
* => allows a STA plus three P2P interfaces
* enum nl80211_plink_state - state of a mesh peer link finite state machine
*
* @NL80211_PLINK_LISTEN: initial state, considered the implicit
- * state of non existent mesh peer links
+ * state of non-existent mesh peer links
* @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
* this mesh peer
* @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
* @NL80211_PLINK_ESTAB: mesh peer link is established
* @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled
* @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh
- * plink are discarded
+ * plink are discarded, except for authentication frames
* @NUM_NL80211_PLINK_STATES: number of peer link states
* @MAX_NL80211_PLINK_STATES: highest numerical value of plink states
*/
#define NL80211_KCK_LEN 16
#define NL80211_KEK_LEN 16
+#define NL80211_KCK_EXT_LEN 24
+#define NL80211_KEK_EXT_LEN 32
+#define NL80211_KCK_EXT_LEN_32 32
#define NL80211_REPLAY_CTR_LEN 8
/**
* @NL80211_REKEY_DATA_KEK: key encryption key (binary)
* @NL80211_REKEY_DATA_KCK: key confirmation key (binary)
* @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary)
+ * @NL80211_REKEY_DATA_AKM: AKM data (OUI, suite type)
* @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal)
* @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
*/
NL80211_REKEY_DATA_KEK,
NL80211_REKEY_DATA_KCK,
NL80211_REKEY_DATA_REPLAY_CTR,
+ NL80211_REKEY_DATA_AKM,
/* keep last */
NUM_NL80211_REKEY_DATA,
NL80211_TDLS_DISABLE_LINK,
};
-/*
+/**
* enum nl80211_ap_sme_features - device-integrated AP features
- * Reserved for future use, no bits are defined in
- * NL80211_ATTR_DEVICE_AP_SME yet.
+ * @NL80211_AP_SME_SA_QUERY_OFFLOAD: SA Query procedures offloaded to driver
+ * when user space indicates support for SA Query procedures offload during
+ * "start ap" with %NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT.
+ */
enum nl80211_ap_sme_features {
+ NL80211_AP_SME_SA_QUERY_OFFLOAD = 1 << 0,
};
- */
/**
* enum nl80211_feature_flags - device/driver features
* @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up
* the connected inactive stations in AP mode.
* @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested
- * to work properly to suppport receiving regulatory hints from
+ * to work properly to support receiving regulatory hints from
* cellular base stations.
* @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: (no longer available, only
* here to reserve the value for API/ABI compatibility)
* enum nl80211_ext_feature_index - bit index of extended features.
* @NL80211_EXT_FEATURE_VHT_IBSS: This driver supports IBSS with VHT datarates.
* @NL80211_EXT_FEATURE_RRM: This driver supports RRM. When featured, user can
- * can request to use RRM (see %NL80211_ATTR_USE_RRM) with
+ * request to use RRM (see %NL80211_ATTR_USE_RRM) with
* %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set
* the ASSOC_REQ_USE_RRM flag in the association request even if
- * NL80211_FEATURE_QUIET is not advertized.
+ * NL80211_FEATURE_QUIET is not advertised.
* @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air
* sniffer which means that it can be configured to hear packets from
* certain groups which can be configured by the
* the BSS that the interface that requested the scan is connected to
* (if available).
* @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the
- * time the last beacon/probe was received. The time is the TSF of the
- * BSS that the interface that requested the scan is connected to
- * (if available).
+ * time the last beacon/probe was received. For a non-MLO connection, the
+ * time is the TSF of the BSS that the interface that requested the scan is
+ * connected to (if available). For an MLO connection, the time is the TSF
+ * of the BSS corresponding with link ID specified in the scan request (if
+ * specified).
* @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of
* channel dwell time.
* @NL80211_EXT_FEATURE_BEACON_RATE_LEGACY: Driver supports beacon rate
- * configuration (AP/mesh), supporting a legacy (non HT/VHT) rate.
+ * configuration (AP/mesh), supporting a legacy (non-HT/VHT) rate.
* @NL80211_EXT_FEATURE_BEACON_RATE_HT: Driver supports beacon rate
* configuration (AP/mesh) with HT rates.
* @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate
* @NL80211_EXT_FEATURE_AP_PMKSA_CACHING: Driver/device supports PMKSA caching
* (set/del PMKSA operations) in AP mode.
*
- * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Driver supports
- * filtering of sched scan results using band specific RSSI thresholds.
+ * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Obsolete
*
* @NL80211_EXT_FEATURE_STA_TX_PWR: This driver supports controlling tx power
* to a station.
* @NL80211_EXT_FEATURE_SAE_OFFLOAD: Device wants to do SAE authentication in
* station mode (SAE password is passed as part of the connect command).
*
+ * @NL80211_EXT_FEATURE_VLAN_OFFLOAD: The driver supports a single netdev
+ * with VLAN tagged frames and separate VLAN-specific netdevs added using
+ * vconfig similarly to the Ethernet case.
+ *
+ * @NL80211_EXT_FEATURE_AQL: The driver supports the Airtime Queue Limit (AQL)
+ * feature, which prevents bufferbloat by using the expected transmission
+ * time to limit the amount of data buffered in the hardware.
+ *
+ * @NL80211_EXT_FEATURE_BEACON_PROTECTION: The driver supports Beacon protection
+ * and can receive key configuration for BIGTK using key indexes 6 and 7.
+ * @NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT: The driver supports Beacon
+ * protection as a client only and cannot transmit protected beacons.
+ *
+ * @NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH: The driver can disable the
+ * forwarding of preauth frames over the control port. They are then
+ * handled as ordinary data frames.
+ *
+ * @NL80211_EXT_FEATURE_PROTECTED_TWT: Driver supports protected TWT frames
+ *
+ * @NL80211_EXT_FEATURE_DEL_IBSS_STA: The driver supports removing stations
+ * in IBSS mode, essentially by dropping their state.
+ *
+ * @NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS: management frame registrations
+ * are possible for multicast frames and those will be reported properly.
+ *
+ * @NL80211_EXT_FEATURE_SCAN_FREQ_KHZ: This driver supports receiving and
+ * reporting scan request with %NL80211_ATTR_SCAN_FREQ_KHZ. In order to
+ * report %NL80211_ATTR_SCAN_FREQ_KHZ, %NL80211_SCAN_FLAG_FREQ_KHZ must be
+ * included in the scan request.
+ *
+ * @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS: The driver
+ * can report tx status for control port over nl80211 tx operations.
+ *
+ * @NL80211_EXT_FEATURE_OPERATING_CHANNEL_VALIDATION: Driver supports Operating
+ * Channel Validation (OCV) when using driver's SME for RSNA handshakes.
+ *
+ * @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK: Device wants to do 4-way
+ * handshake with PSK in AP mode (PSK is passed as part of the start AP
+ * command).
+ *
+ * @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP: Device wants to do SAE authentication
+ * in AP mode (SAE password is passed as part of the start AP command).
+ *
+ * @NL80211_EXT_FEATURE_FILS_DISCOVERY: Driver/device supports FILS discovery
+ * frames transmission
+ *
+ * @NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP: Driver/device supports
+ * unsolicited broadcast probe response transmission
+ *
+ * @NL80211_EXT_FEATURE_BEACON_RATE_HE: Driver supports beacon rate
+ * configuration (AP/mesh) with HE rates.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_LTF: Device supports secure LTF measurement
+ * exchange protocol.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_RTT: Device supports secure RTT measurement
+ * exchange protocol.
+ *
+ * @NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE: Device supports management
+ * frame protection for all management frames exchanged during the
+ * negotiation and range measurement procedure.
+ *
+ * @NL80211_EXT_FEATURE_BSS_COLOR: The driver supports BSS color collision
+ * detection and change announcemnts.
+ *
+ * @NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD: Driver running in AP mode supports
+ * FILS encryption and decryption for (Re)Association Request and Response
+ * frames. Userspace has to share FILS AAD details to the driver by using
+ * @NL80211_CMD_SET_FILS_AAD.
+ *
+ * @NL80211_EXT_FEATURE_RADAR_BACKGROUND: Device supports background radar/CAC
+ * detection.
+ *
+ * @NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE: Device can perform a MAC address
+ * change without having to bring the underlying network device down
+ * first. For example, in station mode this can be used to vary the
+ * origin MAC address prior to a connection to a new AP for privacy
+ * or other reasons. Note that certain driver specific restrictions
+ * might apply, e.g. no scans in progress, no offchannel operations
+ * in progress, and no active connections.
+ *
+ * @NL80211_EXT_FEATURE_PUNCT: Driver supports preamble puncturing in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_NAN: Device supports NAN Pairing which enables
+ * authentication, data encryption and message integrity.
+ *
+ * @NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA: Device supports randomized TA
+ * in authentication and deauthentication frames sent to unassociated peer
+ * using @NL80211_CMD_FRAME.
+ *
+ * @NL80211_EXT_FEATURE_OWE_OFFLOAD: Driver/Device wants to do OWE DH IE
+ * handling in station mode.
+ *
+ * @NL80211_EXT_FEATURE_OWE_OFFLOAD_AP: Driver/Device wants to do OWE DH IE
+ * handling in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_DFS_CONCURRENT: The device supports peer-to-peer or
+ * ad hoc operation on DFS channels under the control of a concurrent
+ * DFS master on the same channel as described in FCC-594280 D01
+ * (Section B.3). This, for example, allows P2P GO and P2P clients to
+ * operate on DFS channels as long as there's a concurrent BSS connection.
+ *
+ * @NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT: The driver has support for SPP
+ * (signaling and payload protected) A-MSDUs and this shall be advertised
+ * in the RSNXE.
+ *
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
*/
NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER,
NL80211_EXT_FEATURE_AIRTIME_FAIRNESS,
NL80211_EXT_FEATURE_AP_PMKSA_CACHING,
- NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD,
+ NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD, /* obsolete */
NL80211_EXT_FEATURE_EXT_KEY_ID,
NL80211_EXT_FEATURE_STA_TX_PWR,
NL80211_EXT_FEATURE_SAE_OFFLOAD,
+ NL80211_EXT_FEATURE_VLAN_OFFLOAD,
+ NL80211_EXT_FEATURE_AQL,
+ NL80211_EXT_FEATURE_BEACON_PROTECTION,
+ NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH,
+ NL80211_EXT_FEATURE_PROTECTED_TWT,
+ NL80211_EXT_FEATURE_DEL_IBSS_STA,
+ NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS,
+ NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT,
+ NL80211_EXT_FEATURE_SCAN_FREQ_KHZ,
+ NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS,
+ NL80211_EXT_FEATURE_OPERATING_CHANNEL_VALIDATION,
+ NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK,
+ NL80211_EXT_FEATURE_SAE_OFFLOAD_AP,
+ NL80211_EXT_FEATURE_FILS_DISCOVERY,
+ NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP,
+ NL80211_EXT_FEATURE_BEACON_RATE_HE,
+ NL80211_EXT_FEATURE_SECURE_LTF,
+ NL80211_EXT_FEATURE_SECURE_RTT,
+ NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE,
+ NL80211_EXT_FEATURE_BSS_COLOR,
+ NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD,
+ NL80211_EXT_FEATURE_RADAR_BACKGROUND,
+ NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE,
+ NL80211_EXT_FEATURE_PUNCT,
+ NL80211_EXT_FEATURE_SECURE_NAN,
+ NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA,
+ NL80211_EXT_FEATURE_OWE_OFFLOAD,
+ NL80211_EXT_FEATURE_OWE_OFFLOAD_AP,
+ NL80211_EXT_FEATURE_DFS_CONCURRENT,
+ NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
* request parameters IE in the probe request
* @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at
- * rate of at least 5.5M. In case non OCE AP is discovered in the channel,
+ * rate of at least 5.5M. In case non-OCE AP is discovered in the channel,
* only the first probe req in the channel will be sent in high rate.
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request
* tx deferral (dot11FILSProbeDelay shall be set to 15ms)
* @NL80211_SCAN_FLAG_MIN_PREQ_CONTENT: minimize probe request content to
* only have supported rates and no additional capabilities (unless
* added by userspace explicitly.)
+ * @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
+ * %NL80211_ATTR_SCAN_FREQ_KHZ. This also means
+ * %NL80211_ATTR_SCAN_FREQUENCIES will not be included.
+ * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for collocated APs reported by
+ * 2.4/5 GHz APs. When the flag is set, the scan logic will use the
+ * information from the RNR element found in beacons/probe responses
+ * received on the 2.4/5 GHz channels to actively scan only the 6GHz
+ * channels on which APs are expected to be found. Note that when not set,
+ * the scan logic would scan all 6GHz channels, but since transmission of
+ * probe requests on non-PSC channels is limited, it is highly likely that
+ * these channels would passively be scanned. Also note that when the flag
+ * is set, in addition to the colocated APs, PSC channels would also be
+ * scanned if the user space has asked for it.
*/
enum nl80211_scan_flags {
NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
NL80211_SCAN_FLAG_HIGH_ACCURACY = 1<<10,
NL80211_SCAN_FLAG_RANDOM_SN = 1<<11,
NL80211_SCAN_FLAG_MIN_PREQ_CONTENT = 1<<12,
+ NL80211_SCAN_FLAG_FREQ_KHZ = 1<<13,
+ NL80211_SCAN_FLAG_COLOCATED_6GHZ = 1<<14,
};
/**
};
/**
- * enum enum nl80211_protocol_features - nl80211 protocol features
+ * enum nl80211_protocol_features - nl80211 protocol features
* @NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP: nl80211 supports splitting
* wiphy dumps (if requested by the application with the attribute
* %NL80211_ATTR_SPLIT_WIPHY_DUMP. Also supported is filtering the
* @NL80211_TDLS_PEER_HT: TDLS peer is HT capable.
* @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable.
* @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable.
+ * @NL80211_TDLS_PEER_HE: TDLS peer is HE capable.
*/
enum nl80211_tdls_peer_capability {
NL80211_TDLS_PEER_HT = 1<<0,
NL80211_TDLS_PEER_VHT = 1<<1,
NL80211_TDLS_PEER_WMM = 1<<2,
+ NL80211_TDLS_PEER_HE = 1<<3,
};
/**
* The instance ID for the follow up Service Discovery Frame. This is u8.
* @NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID: relevant if the function's type
* is follow up. This is a u8.
- * The requestor instance ID for the follow up Service Discovery Frame.
+ * The requester instance ID for the follow up Service Discovery Frame.
* @NL80211_NAN_FUNC_FOLLOW_UP_DEST: the MAC address of the recipient of the
* follow up Service Discovery Frame. This is a binary attribute.
* @NL80211_NAN_FUNC_CLOSE_RANGE: is this function limited for devices in a
* @NL80211_PREAMBLE_HT: HT preamble
* @NL80211_PREAMBLE_VHT: VHT preamble
* @NL80211_PREAMBLE_DMG: DMG preamble
+ * @NL80211_PREAMBLE_HE: HE preamble
*/
enum nl80211_preamble {
NL80211_PREAMBLE_LEGACY,
NL80211_PREAMBLE_HT,
NL80211_PREAMBLE_VHT,
NL80211_PREAMBLE_DMG,
+ NL80211_PREAMBLE_HE,
};
/**
* is valid)
* @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
* the maximum FTMs per burst (if not present anything is valid)
+ * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
+ * trigger based ranging measurement is supported
+ * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
+ * if non-trigger-based ranging measurement is supported
*
* @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
* @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS,
NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT,
NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST,
+ NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED,
+ NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED,
/* keep last */
NUM_NL80211_PMSR_FTM_CAPA_ATTR,
* @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI: request LCI data (flag)
* @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC: request civic location data
* (flag)
+ * @NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED: request trigger based ranging
+ * measurement (flag).
+ * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED are
+ * mutually exclusive.
+ * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
+ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
+ * ranging will be used.
+ * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non-trigger-based
+ * ranging measurement (flag)
+ * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
+ * mutually exclusive.
+ * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
+ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
+ * ranging will be used.
+ * @NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK: negotiate for LMR feedback. Only
+ * valid if either %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED or
+ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set.
+ * @NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR: optional. The BSS color of the
+ * responder. Only valid if %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED
+ * or %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED is set.
*
* @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
* @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES,
NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI,
NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
+ NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
+ NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
+ NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK,
+ NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR,
/* keep last */
NUM_NL80211_PMSR_FTM_REQ_ATTR,
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames
* transmitted (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames
- * that were acknowleged (u32, optional)
+ * that were acknowledged (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the
* busy peer (u32, seconds)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent
*
* @NL80211_HE_OBSS_PD_ATTR_MIN_OFFSET: the OBSS PD minimum tx power offset.
* @NL80211_HE_OBSS_PD_ATTR_MAX_OFFSET: the OBSS PD maximum tx power offset.
+ * @NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET: the non-SRG OBSS PD maximum
+ * tx power offset.
+ * @NL80211_HE_OBSS_PD_ATTR_BSS_COLOR_BITMAP: bitmap that indicates the BSS color
+ * values used by members of the SRG.
+ * @NL80211_HE_OBSS_PD_ATTR_PARTIAL_BSSID_BITMAP: bitmap that indicates the partial
+ * BSSID values used by members of the SRG.
+ * @NL80211_HE_OBSS_PD_ATTR_SR_CTRL: The SR Control field of SRP element.
*
* @__NL80211_HE_OBSS_PD_ATTR_LAST: Internal
* @NL80211_HE_OBSS_PD_ATTR_MAX: highest OBSS PD attribute.
NL80211_HE_OBSS_PD_ATTR_MIN_OFFSET,
NL80211_HE_OBSS_PD_ATTR_MAX_OFFSET,
+ NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET,
+ NL80211_HE_OBSS_PD_ATTR_BSS_COLOR_BITMAP,
+ NL80211_HE_OBSS_PD_ATTR_PARTIAL_BSSID_BITMAP,
+ NL80211_HE_OBSS_PD_ATTR_SR_CTRL,
/* keep last */
__NL80211_HE_OBSS_PD_ATTR_LAST,
NL80211_HE_OBSS_PD_ATTR_MAX = __NL80211_HE_OBSS_PD_ATTR_LAST - 1,
};
+/**
+ * enum nl80211_bss_color_attributes - BSS Color attributes
+ * @__NL80211_HE_BSS_COLOR_ATTR_INVALID: Invalid
+ *
+ * @NL80211_HE_BSS_COLOR_ATTR_COLOR: the current BSS Color.
+ * @NL80211_HE_BSS_COLOR_ATTR_DISABLED: is BSS coloring disabled.
+ * @NL80211_HE_BSS_COLOR_ATTR_PARTIAL: the AID equation to be used..
+ *
+ * @__NL80211_HE_BSS_COLOR_ATTR_LAST: Internal
+ * @NL80211_HE_BSS_COLOR_ATTR_MAX: highest BSS Color attribute.
+ */
+enum nl80211_bss_color_attributes {
+ __NL80211_HE_BSS_COLOR_ATTR_INVALID,
+
+ NL80211_HE_BSS_COLOR_ATTR_COLOR,
+ NL80211_HE_BSS_COLOR_ATTR_DISABLED,
+ NL80211_HE_BSS_COLOR_ATTR_PARTIAL,
+
+ /* keep last */
+ __NL80211_HE_BSS_COLOR_ATTR_LAST,
+ NL80211_HE_BSS_COLOR_ATTR_MAX = __NL80211_HE_BSS_COLOR_ATTR_LAST - 1,
+};
+
+/**
+ * enum nl80211_iftype_akm_attributes - interface type AKM attributes
+ * @__NL80211_IFTYPE_AKM_ATTR_INVALID: Invalid
+ *
+ * @NL80211_IFTYPE_AKM_ATTR_IFTYPES: nested attribute containing a flag
+ * attribute for each interface type that supports AKM suites specified in
+ * %NL80211_IFTYPE_AKM_ATTR_SUITES
+ * @NL80211_IFTYPE_AKM_ATTR_SUITES: an array of u32. Used to indicate supported
+ * AKM suites for the specified interface types.
+ *
+ * @__NL80211_IFTYPE_AKM_ATTR_LAST: Internal
+ * @NL80211_IFTYPE_AKM_ATTR_MAX: highest interface type AKM attribute.
+ */
+enum nl80211_iftype_akm_attributes {
+ __NL80211_IFTYPE_AKM_ATTR_INVALID,
+
+ NL80211_IFTYPE_AKM_ATTR_IFTYPES,
+ NL80211_IFTYPE_AKM_ATTR_SUITES,
+
+ /* keep last */
+ __NL80211_IFTYPE_AKM_ATTR_LAST,
+ NL80211_IFTYPE_AKM_ATTR_MAX = __NL80211_IFTYPE_AKM_ATTR_LAST - 1,
+};
+
+/**
+ * enum nl80211_fils_discovery_attributes - FILS discovery configuration
+ * from IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
+ *
+ * @__NL80211_FILS_DISCOVERY_ATTR_INVALID: Invalid
+ *
+ * @NL80211_FILS_DISCOVERY_ATTR_INT_MIN: Minimum packet interval (u32, TU).
+ * Allowed range: 0..10000 (TU = Time Unit)
+ * @NL80211_FILS_DISCOVERY_ATTR_INT_MAX: Maximum packet interval (u32, TU).
+ * Allowed range: 0..10000 (TU = Time Unit). If set to 0, the feature is disabled.
+ * @NL80211_FILS_DISCOVERY_ATTR_TMPL: Template data for FILS discovery action
+ * frame including the headers.
+ *
+ * @__NL80211_FILS_DISCOVERY_ATTR_LAST: Internal
+ * @NL80211_FILS_DISCOVERY_ATTR_MAX: highest attribute
+ */
+enum nl80211_fils_discovery_attributes {
+ __NL80211_FILS_DISCOVERY_ATTR_INVALID,
+
+ NL80211_FILS_DISCOVERY_ATTR_INT_MIN,
+ NL80211_FILS_DISCOVERY_ATTR_INT_MAX,
+ NL80211_FILS_DISCOVERY_ATTR_TMPL,
+
+ /* keep last */
+ __NL80211_FILS_DISCOVERY_ATTR_LAST,
+ NL80211_FILS_DISCOVERY_ATTR_MAX = __NL80211_FILS_DISCOVERY_ATTR_LAST - 1
+};
+
+/*
+ * FILS discovery template minimum length with action frame headers and
+ * mandatory fields.
+ */
+#define NL80211_FILS_DISCOVERY_TMPL_MIN_LEN 42
+
+/**
+ * enum nl80211_unsol_bcast_probe_resp_attributes - Unsolicited broadcast probe
+ * response configuration. Applicable only in 6GHz.
+ *
+ * @__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INVALID: Invalid
+ *
+ * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT: Maximum packet interval (u32, TU).
+ * Allowed range: 0..20 (TU = Time Unit). IEEE P802.11ax/D6.0
+ * 26.17.2.3.2 (AP behavior for fast passive scanning). If set to 0, the feature is
+ * disabled.
+ * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL: Unsolicited broadcast probe response
+ * frame template (binary).
+ *
+ * @__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST: Internal
+ * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX: highest attribute
+ */
+enum nl80211_unsol_bcast_probe_resp_attributes {
+ __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INVALID,
+
+ NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT,
+ NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL,
+
+ /* keep last */
+ __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST,
+ NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX =
+ __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1
+};
+
+/**
+ * enum nl80211_sae_pwe_mechanism - The mechanism(s) allowed for SAE PWE
+ * derivation. Applicable only when WPA3-Personal SAE authentication is
+ * used.
+ *
+ * @NL80211_SAE_PWE_UNSPECIFIED: not specified, used internally to indicate that
+ * attribute is not present from userspace.
+ * @NL80211_SAE_PWE_HUNT_AND_PECK: hunting-and-pecking loop only
+ * @NL80211_SAE_PWE_HASH_TO_ELEMENT: hash-to-element only
+ * @NL80211_SAE_PWE_BOTH: both hunting-and-pecking loop and hash-to-element
+ * can be used.
+ */
+enum nl80211_sae_pwe_mechanism {
+ NL80211_SAE_PWE_UNSPECIFIED,
+ NL80211_SAE_PWE_HUNT_AND_PECK,
+ NL80211_SAE_PWE_HASH_TO_ELEMENT,
+ NL80211_SAE_PWE_BOTH,
+};
+
+/**
+ * enum nl80211_sar_type - type of SAR specs
+ *
+ * @NL80211_SAR_TYPE_POWER: power limitation specified in 0.25dBm unit
+ *
+ */
+enum nl80211_sar_type {
+ NL80211_SAR_TYPE_POWER,
+
+ /* add new type here */
+
+ /* Keep last */
+ NUM_NL80211_SAR_TYPE,
+};
+
+/**
+ * enum nl80211_sar_attrs - Attributes for SAR spec
+ *
+ * @NL80211_SAR_ATTR_TYPE: the SAR type as defined in &enum nl80211_sar_type.
+ *
+ * @NL80211_SAR_ATTR_SPECS: Nested array of SAR power
+ * limit specifications. Each specification contains a set
+ * of %nl80211_sar_specs_attrs.
+ *
+ * For SET operation, it contains array of %NL80211_SAR_ATTR_SPECS_POWER
+ * and %NL80211_SAR_ATTR_SPECS_RANGE_INDEX.
+ *
+ * For sar_capa dump, it contains array of
+ * %NL80211_SAR_ATTR_SPECS_START_FREQ
+ * and %NL80211_SAR_ATTR_SPECS_END_FREQ.
+ *
+ * @__NL80211_SAR_ATTR_LAST: Internal
+ * @NL80211_SAR_ATTR_MAX: highest sar attribute
+ *
+ * These attributes are used with %NL80211_CMD_SET_SAR_SPEC
+ */
+enum nl80211_sar_attrs {
+ __NL80211_SAR_ATTR_INVALID,
+
+ NL80211_SAR_ATTR_TYPE,
+ NL80211_SAR_ATTR_SPECS,
+
+ __NL80211_SAR_ATTR_LAST,
+ NL80211_SAR_ATTR_MAX = __NL80211_SAR_ATTR_LAST - 1,
+};
+
+/**
+ * enum nl80211_sar_specs_attrs - Attributes for SAR power limit specs
+ *
+ * @NL80211_SAR_ATTR_SPECS_POWER: Required (s32)value to specify the actual
+ * power limit value in units of 0.25 dBm if type is
+ * NL80211_SAR_TYPE_POWER. (i.e., a value of 44 represents 11 dBm).
+ * 0 means userspace doesn't have SAR limitation on this associated range.
+ *
+ * @NL80211_SAR_ATTR_SPECS_RANGE_INDEX: Required (u32) value to specify the
+ * index of exported freq range table and the associated power limitation
+ * is applied to this range.
+ *
+ * Userspace isn't required to set all the ranges advertised by WLAN driver,
+ * and userspace can skip some certain ranges. These skipped ranges don't
+ * have SAR limitations, and they are same as setting the
+ * %NL80211_SAR_ATTR_SPECS_POWER to any unreasonable high value because any
+ * value higher than regulatory allowed value just means SAR power
+ * limitation is removed, but it's required to set at least one range.
+ * It's not allowed to set duplicated range in one SET operation.
+ *
+ * Every SET operation overwrites previous SET operation.
+ *
+ * @NL80211_SAR_ATTR_SPECS_START_FREQ: Required (u32) value to specify the start
+ * frequency of this range edge when registering SAR capability to wiphy.
+ * It's not a channel center frequency. The unit is kHz.
+ *
+ * @NL80211_SAR_ATTR_SPECS_END_FREQ: Required (u32) value to specify the end
+ * frequency of this range edge when registering SAR capability to wiphy.
+ * It's not a channel center frequency. The unit is kHz.
+ *
+ * @__NL80211_SAR_ATTR_SPECS_LAST: Internal
+ * @NL80211_SAR_ATTR_SPECS_MAX: highest sar specs attribute
+ */
+enum nl80211_sar_specs_attrs {
+ __NL80211_SAR_ATTR_SPECS_INVALID,
+
+ NL80211_SAR_ATTR_SPECS_POWER,
+ NL80211_SAR_ATTR_SPECS_RANGE_INDEX,
+ NL80211_SAR_ATTR_SPECS_START_FREQ,
+ NL80211_SAR_ATTR_SPECS_END_FREQ,
+
+ __NL80211_SAR_ATTR_SPECS_LAST,
+ NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
+};
+
+/**
+ * enum nl80211_mbssid_config_attributes - multiple BSSID (MBSSID) and enhanced
+ * multi-BSSID advertisements (EMA) in AP mode.
+ * Kernel uses some of these attributes to advertise driver's support for
+ * MBSSID and EMA.
+ * Remaining attributes should be used by the userspace to configure the
+ * features.
+ *
+ * @__NL80211_MBSSID_CONFIG_ATTR_INVALID: Invalid
+ *
+ * @NL80211_MBSSID_CONFIG_ATTR_MAX_INTERFACES: Used by the kernel to advertise
+ * the maximum number of MBSSID interfaces supported by the driver.
+ * Driver should indicate MBSSID support by setting
+ * wiphy->mbssid_max_interfaces to a value more than or equal to 2.
+ *
+ * @NL80211_MBSSID_CONFIG_ATTR_MAX_EMA_PROFILE_PERIODICITY: Used by the kernel
+ * to advertise the maximum profile periodicity supported by the driver
+ * if EMA is enabled. Driver should indicate EMA support to the userspace
+ * by setting wiphy->ema_max_profile_periodicity to
+ * a non-zero value.
+ *
+ * @NL80211_MBSSID_CONFIG_ATTR_INDEX: Mandatory parameter to pass the index of
+ * this BSS (u8) in the multiple BSSID set.
+ * Value must be set to 0 for the transmitting interface and non-zero for
+ * all non-transmitting interfaces. The userspace will be responsible
+ * for using unique indices for the interfaces.
+ * Range: 0 to wiphy->mbssid_max_interfaces-1.
+ *
+ * @NL80211_MBSSID_CONFIG_ATTR_TX_IFINDEX: Mandatory parameter for
+ * a non-transmitted profile which provides the interface index (u32) of
+ * the transmitted profile. The value must match one of the interface
+ * indices advertised by the kernel. Optional if the interface being set up
+ * is the transmitting one, however, if provided then the value must match
+ * the interface index of the same.
+ *
+ * @NL80211_MBSSID_CONFIG_ATTR_EMA: Flag used to enable EMA AP feature.
+ * Setting this flag is permitted only if the driver advertises EMA support
+ * by setting wiphy->ema_max_profile_periodicity to non-zero.
+ *
+ * @__NL80211_MBSSID_CONFIG_ATTR_LAST: Internal
+ * @NL80211_MBSSID_CONFIG_ATTR_MAX: highest attribute
+ */
+enum nl80211_mbssid_config_attributes {
+ __NL80211_MBSSID_CONFIG_ATTR_INVALID,
+
+ NL80211_MBSSID_CONFIG_ATTR_MAX_INTERFACES,
+ NL80211_MBSSID_CONFIG_ATTR_MAX_EMA_PROFILE_PERIODICITY,
+ NL80211_MBSSID_CONFIG_ATTR_INDEX,
+ NL80211_MBSSID_CONFIG_ATTR_TX_IFINDEX,
+ NL80211_MBSSID_CONFIG_ATTR_EMA,
+
+ /* keep last */
+ __NL80211_MBSSID_CONFIG_ATTR_LAST,
+ NL80211_MBSSID_CONFIG_ATTR_MAX = __NL80211_MBSSID_CONFIG_ATTR_LAST - 1,
+};
+
+/**
+ * enum nl80211_ap_settings_flags - AP settings flags
+ *
+ * @NL80211_AP_SETTINGS_EXTERNAL_AUTH_SUPPORT: AP supports external
+ * authentication.
+ * @NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT: Userspace supports SA Query
+ * procedures offload to driver. If driver advertises
+ * %NL80211_AP_SME_SA_QUERY_OFFLOAD in AP SME features, userspace shall
+ * ignore SA Query procedures and validations when this flag is set by
+ * userspace.
+ */
+enum nl80211_ap_settings_flags {
+ NL80211_AP_SETTINGS_EXTERNAL_AUTH_SUPPORT = 1 << 0,
+ NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT = 1 << 1,
+};
#endif /* __LINUX_NL80211_H */
projects / thirdparty / iw.git / blobdiff