Simon Glass [Mon, 22 Feb 2016 04:08:48 +0000 (21:08 -0700)]
exynos: video: Combine LCD driver into one file
At present exynos_fimd.c is the controller and exynos_fb.c is the U-Boot
LCD interface. With driver model we want these in one file, so join them
in preparation.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:14 +0000 (22:18 +0530)]
board: samsung: add initial Espresso7420 board support
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:12 +0000 (22:18 +0530)]
arm: exynos: realign the code to allow support for newer 64-bit platforms
The existing Exynos 32-bit platform support needs to be realigned in
order to support newer 64-bit Exynos platforms. The driver model will
be utlized for drivers on the 64-bit Exynos platforms and so some of
the older platform support code would not be required for the newer
64-bit Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:11 +0000 (22:18 +0530)]
serial: s5p: use clock api to get clock rate
On Exynos platforms that support clock driver API, allow the driver to
use clock api get the SCLK clock rate.
Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:10 +0000 (22:18 +0530)]
serial: s5p: get the port id number from the alias of the device node
The port id, if not specified in the device node, can be obtained from
the alias of the device node listed in the aliases node.
Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:09 +0000 (22:18 +0530)]
clk: exynos: add clock driver for Exynos7420 Soc
Add a clock driver for Exynos7420 SoC. There are about 25 clock controller
blocks in Exynos7420 out of which support for topc, top0 and peric1 blocks
are added in this initial version of the driver.
Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:08 +0000 (22:18 +0530)]
pinctrl: Add pinctrl driver support for Exynos7420 SoC
Add pinctrl driver support for Samsung's Exynos7420 SoC. The changes
have been split into Exynos7420 specific and common Exynos specific
portions so that this implementation is reusable on other Exynos
SoCs as well.
The Exynos pinctrl driver supports only device tree based pin
configuration. The bindings used are similar to the ones used in the
linux kernel.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Thomas Abraham [Sat, 23 Apr 2016 16:48:07 +0000 (22:18 +0530)]
pinctrl: add the DM_UC_FLAG_SEQ_ALIAS flag for numbering the devices
It is possible to have multiple pin controllers in the system. Use the
DM_UC_FLAG_SEQ_ALIAS flag so that the pinctrl instances are assigned
a sequence number.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Dan Murphy [Mon, 2 May 2016 20:46:02 +0000 (15:46 -0500)]
net: phy: dp83867: Add SGMII helper for configuration
The code assumed that if the interface is not RGMII configured
then it must be SGMII configured. This device has the ability
to support most of the MII interfaces. Therefore add the
helper for SGMII and only configure the device if the interface is
configured for SGMII.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Dan Murphy [Mon, 2 May 2016 20:46:01 +0000 (15:46 -0500)]
net: phy: Add phy_interface_is_sgmii to phy.h
Add a helper to phy.h to identify whether the
phy is configured for SGMII all variables.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Dan Murphy [Mon, 2 May 2016 20:45:59 +0000 (15:45 -0500)]
net: phy: ti: Allow the driver to be more configurable
Not all devices use the same internal delay or fifo depth.
Add the ability to set the internal delay for rx or tx and the
fifo depth via the devicetree. If the value is not set in the
devicetree then set the delay to the default.
If devicetree is not used then use the default defines within the
driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Dan Murphy [Mon, 2 May 2016 20:45:57 +0000 (15:45 -0500)]
net: zynq_gem: Add the passing of the phy-handle node
Add the ability to pass the phy-handle node offset
to the phy driver. This allows the phy driver
to access the DT subnode's data and parse accordingly.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mugunthan V N [Thu, 28 Apr 2016 10:06:07 +0000 (15:36 +0530)]
drivers: net: cpsw: add support for reading mac address from efuse
Different TI platforms has to read with different combination to
get the mac address from efuse. So add support to read mac address
based on machine/device compatibles.
The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c
done by Tony Lindgren.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mugunthan V N [Thu, 28 Apr 2016 10:06:06 +0000 (15:36 +0530)]
drivers: net: cpsw: fix get mdio base and gmii_sel reg from DT
Since dra7x platforms address bus is define as 64 bits to support
LAPE, fdtdec_get_addr() returns a invalid address for mdio based
and gmii_sel register address. Fixing this by using
fdtdec_get_addr_size_auto_noparent() which will derive address
cell and size cell from its parent.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mugunthan V N [Thu, 28 Apr 2016 10:06:04 +0000 (15:36 +0530)]
drivers: net: cpsw: fix cpsw dp parse when num slaves as 1
On some boards number of slaves can be 1 when only one port
ethernet is pinned out. So do not break when slave_index and
num slaves check fails, instead continue to parse the next
child.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mugunthan V N [Thu, 28 Apr 2016 10:06:03 +0000 (15:36 +0530)]
ti_omap5_common: eth: do not define DM_ETH for spl
Since omap's spl doesn't support DM currently, do not define
DM_ETH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mugunthan V N [Thu, 28 Apr 2016 10:06:02 +0000 (15:36 +0530)]
drivers: core: device: add support to check dt compatible for a device/machine
Provide an api to check whether the given device or machine is
compatible with the given compat string which helps in making
decisions in drivers based on device or machine compatible.
Idea taken from Linux.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Kevin Smith [Thu, 31 Mar 2016 19:33:12 +0000 (19:33 +0000)]
net: phy: Add PHY driver for mv88e61xx switches
The previous mv88e61xx driver was a driver for configuring the
switch, but did not integrate with the PHY/networking system, so
it could not be used as a PHY by U-boot. This is a complete
rework to support this device as a PHY.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Kevin Smith [Thu, 31 Mar 2016 19:33:12 +0000 (19:33 +0000)]
net: Remove unused mv88e61xx switch driver
No boards are using this driver. Remove in preparation for a new
driver with integrated PHY support.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
Michal Simek [Fri, 20 May 2016 12:59:33 +0000 (14:59 +0200)]
ARM: zynq: Simplify zynq configuration
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 18 May 2016 12:46:28 +0000 (14:46 +0200)]
phy: marvell: Do not reset phy after negotiation
The patch
"net: phy: do not read configuration register on reset"
(sha1: a058052c358c3ecf5f394ff37def6a45eb26768c)
was causing regression on zynq zc702 board where Marwell 88e1118
phy was resetted after negotiation was setup.
Phy reset is done pretty early in phy_connect_dev() and doens't need to
be called again in phy code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 17 May 2016 12:03:50 +0000 (14:03 +0200)]
image: Add boot_get_fpga() to load fpga with bootm
Add function boot_get_fpga() which find and load bitstream to
programmable logic if fpga entry is present.
Function is supported on Xilinx devices for full and partial bitstreams
in BIN and BIT format.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove additional blankline in image.h
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Alexander Graf [Thu, 12 May 2016 11:44:01 +0000 (13:44 +0200)]
ARM64: zynqmp: Align gic ranges for 64k in device tree
The GIC ranges in the zynqmp device tree are only 4kb aligned. Since
commit 12e14066f we automatically deal with aliases GIC regions though,
so we can map them transparently into guests even on 64kb page size
systems.
This patch makes use of that features and sets GICC and GICV to 64kb
aligned and sized regions.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the zynqmpimage to mkimage.
Only basic functionality is supported without encryption and register
initialization with one partition which is filled by U-Boot SPL.
For more detail information look at Xilinx ZynqMP TRM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Fri, 22 Apr 2016 09:48:49 +0000 (11:48 +0200)]
ARM64: zynqmp: Add support for reading MAC from eeprom
Add support for on board eeprom with programmed MAC for using in u-boot
to have uniq address for every board.
Most of the time uniq MAC address is on a label on the board.
If address is not programmed use these command to program it.
ARM: zynq: load u-boot.img whether CONFIG_OF_SEPARATE is defined or not
Since commit ad1ecd2063da ("fdt: Build a U-Boot binary without device
tree"), u-boot-dtb.img is identical to u-boot.img, so SPL can always
load u-boot.img whether CONFIG_OF_SEPARATE is defined or not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Fri, 22 Apr 2016 19:56:21 +0000 (21:56 +0200)]
ARM: sama5d2: Implement boot device autodetection
Implement support for saving ARM register R4 early during boot using
save_boot_params . Implement support for decoding the stored register
R4 value in spl_boot_device() to obtain boot device from which the
SoC booted. This way, the SPL will always load U-Boot from the same
device from which the SPL itself booted instead of using hard-coded
boot device.
This functionality is useful for example when booting sama5d2-xplained
from SD card, where by default the SPL would try loading the U-Boot
from eMMC and fail. This is because eMMC is on SDHCI0 (BOOT_DEVICE_MMC1),
while SD slot is on SDHCI1 (BOOT_DEVICE_MMC2) and the SPL was hard-wired
to always boot from BOOT_DEVICE_MMC1.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Marek Vasut [Mon, 18 Apr 2016 16:30:41 +0000 (18:30 +0200)]
ARM: atmel: Enable FIT image support for SAMA5Dx
Enable the fitImage support for the entire SAMA5Dx lineup of CPUs.
The fitImage is superior image format to uImage and it is useful
to have it available.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebase on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Martin Hejnfelt [Thu, 19 May 2016 07:11:58 +0000 (09:11 +0200)]
omap3: Fix SPI registers on am33xx and am43xx
When the base registers are read from device tree the base is not
0x48030100 as the driver expects, but 0x48030000, resulting in
non functioning SPI. To deal with this, use same idea as how this
is done in the linux kernel (drivers/spi/spi-omap2-mcspi.c) and
add a structure with a field that is used to shift the registers
on these systems.
Tom Rini [Fri, 13 May 2016 14:54:04 +0000 (10:54 -0400)]
kbuild: fixdep: Check fstat(2) return value
Coverity has recently added a check that will find when we don't check
the return code from fstat(2). Copy/paste the checking logic that
print_deps() has with an appropriate re-wording of the perror() message.
Michal Simek [Wed, 4 May 2016 13:14:11 +0000 (15:14 +0200)]
spl: Setup default value for OF_LIST
OF_LIST can't remain empty that's why setup it up to default DTB.
If it is empty u-boot.img is created without FDT partition:
For example:
./tools/mkimage -f auto -A arm -T firmware -C none -O u-boot -a
0x8000000 -e 0 -n "U-Boot 2016.05-rc3 ..." -E -b -d u-boot-nodtb.bin u-boot.img
Can't set 'timestamp' property for '' node (FDT_ERR_NOSPACE)
FIT description: Firmware image with one or more FDT blobs
Created: Wed May 4 15:02:52 2016
Image 0 (firmware@1)
Description: U-Boot 2016.05-rc3-00080-gff2e12ae22a8-dirty for zynqmp
board
Created: Wed May 4 15:02:52 2016
Type: Firmware
Compression: uncompressed
Data Size: unavailable
Architecture: ARM
Load Address: 0x08000000
Default Configuration: 'conf@1'
Configuration 0 (conf@1)
Description: unavailable
Kernel: unavailable
And then image like this doesn't contain description and link to FDT and
can't boot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Michal Simek [Wed, 4 May 2016 13:08:00 +0000 (15:08 +0200)]
spl: fit: Print error message when FDT is not present
When FDT is not present in the image user doesn't get any error what's
wrong. Print error message if LIBCOMMON_SUPPORT is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Seris-cc: uboot Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 1 May 2016 19:55:38 +0000 (13:55 -0600)]
mkimage: Add a quiet mode
Some build systems want to be quiet unless there is a problem. At present
mkimage displays quite a bit of information when generating a FIT file. Add
a '-q' flag to silence this.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 1 May 2016 19:55:37 +0000 (13:55 -0600)]
image-fit: Don't display an error in fit_set_timestamp()
This function returns an error code and its caller may be able to fix the
error. For example fit_handle_file() expands the device tree to fit if there
is a lack of space.
In this case the caller does not want an error displayed. It is confusing,
since it suggests that something is wrong, when it fact everything is fine.
Drop the error.
Stephen Warren [Mon, 25 Apr 2016 21:55:42 +0000 (15:55 -0600)]
malloc: improve memalign fragmentation fix
Commit 4f144a416469 "malloc: work around some memalign fragmentation
issues" enhanced memalign() so that it can succeed in more cases where
heap fragmentation is present. However, it did not solve as many cases
as it could. This patch enhances the code to cover more cases.
The alignment code works by allocating more space than the user requests,
then adjusting the returned pointer to achieve alignment. In general, one
must allocate "alignment" bytes more than the user requested in order to
guarantee that alignment is possible. This is what the original code does.
The previous enhancement attempted a second allocation if the padded
allocation failed, and succeeded if that allocation just happened to be
aligned; a fluke that happened often in practice. There are still cases
where this could fail, yet where it is still possible to honor the user's
allocation request. In particular, if the heap contains a free region that
is large enough for the user's request, and for leading padding to ensure
alignment, but has no or little space for any trailing padding. In this
case, we can make a third(!) allocation attempt after calculating exactly
the size of the leading padding required to achieve alignment, which is
the minimal over-allocation needed for the overall memalign() operation to
succeed if the third and second allocations end up at the same location.
This patch isn't checkpatch-clean, since it conforms to the existing
coding style in dlmalloc.c, which is different to the rest of U-Boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Sun, 22 May 2016 08:45:39 +0000 (01:45 -0700)]
x86: galileo: Override SMBIOS product name
Override the default product name U-Boot reports in the SMBIOS
table, to be compatible with the Intel provided UEFI BIOS, as
Linux kernel drivers (drivers/mfd/intel_quark_i2c_gpio.c and
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c) make use of
it to do different board level configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / people / ms / u-boot.git / log
