[people/ms/u-boot.git] / include / configs / G2000.h

/*
 * (C) Copyright 2004
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
#define CONFIG_G2000		1	/* ...on a PLU405 board		*/

#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000

#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/

#define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */

#if 0 /* test-only */
#define CONFIG_BAUDRATE		115200
#else
#define CONFIG_BAUDRATE		9600
#endif

#define CONFIG_PREBOOT

#undef	CONFIG_BOOTARGS

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off\0"				\
	"addmisc=setenv bootargs ${bootargs} "				\
		"console=ttyS0,${baudrate} "				\
		"panic=1\0"						\
	"flash_nfs=run nfsargs addip addmisc;"				\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip addmisc;"				\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"net_nfs=tftp 200000 ${bootfile};"				\
		"run nfsargs addip addmisc;bootm\0"			\
	"rootpath=/opt/eldk/ppc_4xx\0"					\
	"bootfile=/tftpboot/g2000/pImage\0"				\
	"kernel_addr=ff800000\0"				        \
	"ramdisk_addr=ff900000\0"				        \
	"pciconfighost=yes\0"				                \
	""
#define CONFIG_BOOTCOMMAND	"run net_nfs"

#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/


#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII		1	/* MII PHY management		*/
#define CONFIG_PHY_ADDR		0	/* PHY address			*/
#define CONFIG_PHY1_ADDR	1	/* PHY address			*/

#if 0 /* test-only */
#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
#endif


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DATE
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_BSP
#define CONFIG_CMD_EEPROM


#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#if 0 /* test-only */
#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/

#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/

#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/

#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#define CONFIG_CONS_INDEX	1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_serial_clock()

#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD	    691200

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
	 57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */

#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */

#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */

/*----------------------------------------------------------------------------*/
/* adding Ethernet setting:  FTS OUI 00:11:0B */
/*----------------------------------------------------------------------------*/
#define CONFIG_ETHADDR          00:11:0B:00:00:01
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR         00:11:0B:00:00:02
#define CONFIG_IPADDR		10.48.8.178
#define CONFIG_IP1ADDR		10.48.8.188
#define CONFIG_NETMASK		255.255.255.128
#define CONFIG_SERVERIP		10.48.8.138

/*-----------------------------------------------------------------------
 * RTC stuff
 *-----------------------------------------------------------------------
 */
#define CONFIG_RTC_DS1337
#define CONFIG_SYS_I2C_RTC_ADDR	0x68

#if 0 /* test-only */
/*-----------------------------------------------------------------------
 * NAND-FLASH stuff
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/

#define CONFIG_SYS_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */

#endif

/*-----------------------------------------------------------------------
 * PCI stuff
 *-----------------------------------------------------------------------
 */
#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
#define PCI_HOST_FORCE  1               /* configure as pci host        */
#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

#define CONFIG_PCI			/* include pci support	        */
#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
					/* resource configuration       */

#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
#define CONFIG_SYS_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
#define CONFIG_SYS_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#if 0 /* APC405 */
#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant		*/
#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
#undef CONFIG_SYS_FLASH_PROTECTION		/* don't use hardware protection	*/
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* test-only...*/
#define CONFIG_SYS_FLASH_INCREMENT	0x01000000 /* test-only */
#else /* G2000 */
#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant		*/
#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#undef CONFIG_SYS_FLASH_PROTECTION		/* don't use hardware protection	*/
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
#define CONFIG_SYS_FLASH_BASE		0xFF800000 /* test-only...*/
#define CONFIG_SYS_FLASH_INCREMENT	0x01000000 /* test-only */
#endif

#define CONFIG_SYS_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */

#define CONFIG_SYS_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
#define CONFIG_SYS_JFFS2_NUM_BANKS     1           /* ! second bank contains u-boot    */

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_MONITOR_BASE	0xFFFC0000
#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/

/*-----------------------------------------------------------------------
 * Environment Variable setup
 */
#if 1 /* test-only */
#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
				   /* total size of a CAT24WC16 is 2048 bytes */

#else	/* DEFAULT: environment in flash, using redundand flash sectors */

#define CONFIG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars */
#define CONFIG_ENV_ADDR		0xFFFA0000 /* environment starts before u-boot */
#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128k bytes may be used for env vars*/

#endif

/*-----------------------------------------------------------------------
 * I2C EEPROM (CAT24WC16) for environment
 */
#define CONFIG_HARD_I2C			/* I2c with hardware support */
#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE		0x7F

#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
/* CAT24WC08/16... */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"	*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
					/* 16 byte page write mode using*/
					/* last 4 bits of the address	*/
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */

/*-----------------------------------------------------------------------
 * External Bus Controller (EBC) Setup
 */

/* Memory Bank 0 (Intel Strata Flash) initialization                            */
#define CONFIG_SYS_EBC_PB0AP   0x92015480
#define CONFIG_SYS_EBC_PB0CR   0xFF87A000          /* BAS=0xFF8,BS=08MB,BU=R/W,BW=16bit*/

/* Memory Bank 1 ( Power TAU) initialization               */
/* #define CONFIG_SYS_EBC_PB1AP           0x04041000 */
/* #define CONFIG_SYS_EBC_PB1CR           0xF0018000   */  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
#define CONFIG_SYS_EBC_PB1AP           0x00000000
#define CONFIG_SYS_EBC_PB1CR           0x00000000

/* Memory Bank 2 (Intel Flash) initialization                 */
#define CONFIG_SYS_EBC_PB2AP           0x00000000
#define CONFIG_SYS_EBC_PB2CR           0x00000000

/* Memory Bank 3 (NAND) initialization                        */
#define CONFIG_SYS_EBC_PB3AP           0x92015480
#define CONFIG_SYS_EBC_PB3CR           0xF40B8000  /*addr 0xF40, BS=32M,BU=R/W, BW=8bit */

/* Memory Bank 4 (FPGA regs) initialization                                     */
#define CONFIG_SYS_EBC_PB4AP           0x00000000
#define CONFIG_SYS_EBC_PB4CR           0x00000000  /* leave it blank  */

#define CONFIG_SYS_NAND_BASE   0xF4000000

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM	  1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/

#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Definitions for GPIO setup (PPC405EP specific)
 *
 * GPIO0[0]     - External Bus Controller BLAST output
 * GPIO0[1-9]   - Instruction trace outputs
 * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
 * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 * GPIO0[24-27] - UART0 control signal inputs/outputs
 * GPIO0[28-29] - UART1 data signal input/output
 * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 *
 * following GPIO setting changed for G20000, 080304
 */
#define CONFIG_SYS_GPIO0_OSRL          0x40005555
#define CONFIG_SYS_GPIO0_OSRH          0x40000110
#define CONFIG_SYS_GPIO0_ISR1L         0x00000000
#define CONFIG_SYS_GPIO0_ISR1H         0x15555445
#define CONFIG_SYS_GPIO0_TSRL          0x00000000
#define CONFIG_SYS_GPIO0_TSRH          0x00000000
#define CONFIG_SYS_GPIO0_TCR           0xF7FF8014

/*
 * Default speed selection (cpu_plb_opb_ebc) in mhz.
 * This value will be set if iic boot eprom is disabled.
 */
#if 1
#define PLLMR0_DEFAULT	 PLLMR0_266_66_33_33
#define PLLMR1_DEFAULT	 PLLMR1_266_66_33_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
#endif

#endif	/* __CONFIG_H */
Commit	Line	Data
a20b27a3 SR	1	/*
	2	* (C) Copyright 2004
	3	* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
a20b27a3 SR	6	*/
	7
	8	/*
	9	* board/config.h - configuration options, board specific
	10	*/
	11
	12	#ifndef __CONFIG_H
	13	#define __CONFIG_H
	14
	15	/*
	16	* High Level Configuration Options
	17	* (easy to change)
	18	*/
	19
	20	#define CONFIG_405EP 1 /* This is a PPC405 CPU */
	21	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
	22	#define CONFIG_G2000 1 /* ...on a PLU405 board */
	23
2ae18241 WD	24	#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
2ae18241 WD	25
a20b27a3 SR	26	#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
	27	#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
	28
	29	#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
	30
	31	#if 0 /* test-only */
	32	#define CONFIG_BAUDRATE 115200
	33	#else
	34	#define CONFIG_BAUDRATE 9600
	35	#endif
	36
	37	#define CONFIG_PREBOOT
	38
	39	#undef CONFIG_BOOTARGS
	40
	41	#define CONFIG_EXTRA_ENV_SETTINGS \
	42	"nfsargs=setenv bootargs root=/dev/nfs rw " \
fe126d8b	43	"nfsroot=${serverip}:${rootpath}\0" \
a20b27a3	44	"ramargs=setenv bootargs root=/dev/ram rw\0" \
fe126d8b WD	45	"addip=setenv bootargs ${bootargs} " \
	46	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	47	":${hostname}:${netdev}:off\0" \
	48	"addmisc=setenv bootargs ${bootargs} " \
	49	"console=ttyS0,${baudrate} " \
a20b27a3 SR	50	"panic=1\0" \
a20b27a3 SR	51	"flash_nfs=run nfsargs addip addmisc;" \
fe126d8b	52	"bootm ${kernel_addr}\0" \
a20b27a3	53	"flash_self=run ramargs addip addmisc;" \
fe126d8b WD	54	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
fe126d8b WD	55	"net_nfs=tftp 200000 ${bootfile};" \
a20b27a3 SR	56	"run nfsargs addip addmisc;bootm\0" \
	57	"rootpath=/opt/eldk/ppc_4xx\0" \
	58	"bootfile=/tftpboot/g2000/pImage\0" \
	59	"kernel_addr=ff800000\0" \
	60	"ramdisk_addr=ff900000\0" \
	61	"pciconfighost=yes\0" \
	62	""
	63	#define CONFIG_BOOTCOMMAND "run net_nfs"
	64
6d0f6bcf	65	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
a20b27a3	66
a20b27a3	67
96e21f86	68	#define CONFIG_PPC4xx_EMAC
a20b27a3 SR	69	#define CONFIG_MII 1 /* MII PHY management */
	70	#define CONFIG_PHY_ADDR 0 /* PHY address */
	71	#define CONFIG_PHY1_ADDR 1 /* PHY address */
	72
	73	#if 0 /* test-only */
	74	#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
	75	#endif
	76
60a0876b	77
11799434 JL	78	/*
	79	* BOOTP options
	80	*/
	81	#define CONFIG_BOOTP_BOOTFILESIZE
	82	#define CONFIG_BOOTP_BOOTPATH
	83	#define CONFIG_BOOTP_GATEWAY
	84	#define CONFIG_BOOTP_HOSTNAME
	85
	86
60a0876b JL	87	/*
	88	* Command line configuration.
	89	*/
	90	#include <config_cmd_default.h>
	91
	92	#define CONFIG_CMD_DHCP
	93	#define CONFIG_CMD_PCI
	94	#define CONFIG_CMD_IRQ
	95	#define CONFIG_CMD_ELF
	96	#define CONFIG_CMD_DATE
	97	#define CONFIG_CMD_I2C
	98	#define CONFIG_CMD_MII
	99	#define CONFIG_CMD_PING
	100	#define CONFIG_CMD_BSP
	101	#define CONFIG_CMD_EEPROM
	102
a20b27a3 SR	103
	104	#undef CONFIG_WATCHDOG /* watchdog disabled */
	105
	106	#if 0 /* test-only */
	107	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
	108	#endif
	109
	110	/*
	111	* Miscellaneous configurable options
	112	*/
6d0f6bcf JCPV	113	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6d0f6bcf JCPV	114	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
a20b27a3	115
6d0f6bcf	116	#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
a20b27a3	117
60a0876b	118	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	119	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
a20b27a3	120	#else
6d0f6bcf	121	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
a20b27a3	122	#endif
6d0f6bcf JCPV	123	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	124	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	125	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
a20b27a3	126
6d0f6bcf	127	#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
a20b27a3	128
6d0f6bcf	129	#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
a20b27a3 SR	130
	131	#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
	132
6d0f6bcf JCPV	133	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
6d0f6bcf JCPV	134	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
a20b27a3	135
550650dd SR	136	#define CONFIG_CONS_INDEX 1
	137	#define CONFIG_SYS_NS16550
	138	#define CONFIG_SYS_NS16550_SERIAL
	139	#define CONFIG_SYS_NS16550_REG_SIZE 1
	140	#define CONFIG_SYS_NS16550_CLK get_serial_clock()
	141
6d0f6bcf	142	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
6d0f6bcf	143	#define CONFIG_SYS_BASE_BAUD 691200
a20b27a3 SR	144
a20b27a3 SR	145	/* The following table includes the supported baudrates */
6d0f6bcf	146	#define CONFIG_SYS_BAUDRATE_TABLE \
a20b27a3 SR	147	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
	148	57600, 115200, 230400, 460800, 921600 }
	149
6d0f6bcf JCPV	150	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6d0f6bcf JCPV	151	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
a20b27a3	152
6d0f6bcf	153	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
a20b27a3 SR	154
	155	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
	156	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
	157
	158	#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
	159
6d0f6bcf	160	#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
a20b27a3 SR	161
	162	/----------------------------------------------------------------------------/
	163	/* adding Ethernet setting: FTS OUI 00:11:0B */
	164	/----------------------------------------------------------------------------/
	165	#define CONFIG_ETHADDR 00:11:0B:00:00:01
e2ffd59b	166	#define CONFIG_HAS_ETH1
a20b27a3 SR	167	#define CONFIG_ETH1ADDR 00:11:0B:00:00:02
	168	#define CONFIG_IPADDR 10.48.8.178
	169	#define CONFIG_IP1ADDR 10.48.8.188
	170	#define CONFIG_NETMASK 255.255.255.128
	171	#define CONFIG_SERVERIP 10.48.8.138
	172
	173	/*-----------------------------------------------------------------------
	174	* RTC stuff
	175	*-----------------------------------------------------------------------
	176	*/
	177	#define CONFIG_RTC_DS1337
6d0f6bcf	178	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
a20b27a3 SR	179
	180	#if 0 /* test-only */
	181	/*-----------------------------------------------------------------------
	182	* NAND-FLASH stuff
	183	*-----------------------------------------------------------------------
	184	*/
6d0f6bcf	185	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
a20b27a3	186
6d0f6bcf JCPV	187	#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
	188	#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
	189	#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
	190	#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
a20b27a3	191
a20b27a3 SR	192	#endif
	193
	194	/*-----------------------------------------------------------------------
	195	* PCI stuff
	196	*-----------------------------------------------------------------------
	197	*/
	198	#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
	199	#define PCI_HOST_FORCE 1 /* configure as pci host */
	200	#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
	201
	202	#define CONFIG_PCI /* include pci support */
842033e6	203	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
a20b27a3 SR	204	#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
	205	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	206	/* resource configuration */
	207
	208	#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
	209
	210	#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
	211
6d0f6bcf JCPV	212	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
	213	#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
	214	#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
	215	#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
	216	#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
	217	#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
	218	#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
	219	#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
	220	#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
a20b27a3 SR	221
	222	/*
	223	* For booting Linux, the board info and command line data
	224	* have to be in the first 8 MB of memory, since this is
	225	* the maximum mapped by the Linux kernel during initialization.
	226	*/
6d0f6bcf	227	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
a20b27a3 SR	228
	229	/*-----------------------------------------------------------------------
	230	* FLASH organization
	231	*/
	232	#if 0 /* APC405 */
6d0f6bcf JCPV	233	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
	234	#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
	235	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
	236	#undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */
	237	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
	238	#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* test-only...*/
	239	#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* test-only */
a20b27a3	240	#else /* G2000 */
6d0f6bcf JCPV	241	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
	242	#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
	243	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	244	#undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */
	245	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
	246	#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* test-only...*/
	247	#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* test-only */
a20b27a3 SR	248	#endif
a20b27a3 SR	249
6d0f6bcf	250	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
a20b27a3	251
6d0f6bcf JCPV	252	#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
6d0f6bcf JCPV	253	#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
a20b27a3 SR	254
	255	/*-----------------------------------------------------------------------
	256	* Start addresses for the final memory configuration
	257	* (Set up by the startup code)
6d0f6bcf	258	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
a20b27a3	259	*/
6d0f6bcf JCPV	260	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	261	#define CONFIG_SYS_MONITOR_BASE 0xFFFC0000
	262	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
	263	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
a20b27a3 SR	264
	265	/*-----------------------------------------------------------------------
	266	* Environment Variable setup
	267	*/
	268	#if 1 /* test-only */
bb1f8b4f	269	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
0e8d1586 JCPV	270	#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
0e8d1586 JCPV	271	#define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
a20b27a3 SR	272	/* total size of a CAT24WC16 is 2048 bytes */
	273
	274	#else /* DEFAULT: environment in flash, using redundand flash sectors */
	275
5a1aceb0	276	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
0e8d1586 JCPV	277	#define CONFIG_ENV_ADDR 0xFFFA0000 /* environment starts before u-boot */
0e8d1586 JCPV	278	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k bytes may be used for env vars*/
a20b27a3 SR	279
	280	#endif
	281
	282	/*-----------------------------------------------------------------------
	283	* I2C EEPROM (CAT24WC16) for environment
	284	*/
	285	#define CONFIG_HARD_I2C /* I2c with hardware support */
d0b0dcaa	286	#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
6d0f6bcf JCPV	287	#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
6d0f6bcf JCPV	288	#define CONFIG_SYS_I2C_SLAVE 0x7F
a20b27a3	289
6d0f6bcf	290	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
a20b27a3	291	/* CAT24WC08/16... */
6d0f6bcf	292	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
a20b27a3	293	/* mask of address bits that overflow into the "EEPROM chip address" */
6d0f6bcf JCPV	294	#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
6d0f6bcf JCPV	295	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
a20b27a3 SR	296	/* 16 byte page write mode using*/
a20b27a3 SR	297	/* last 4 bits of the address */
6d0f6bcf	298	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
a20b27a3	299
a20b27a3 SR	300	/*-----------------------------------------------------------------------
	301	* External Bus Controller (EBC) Setup
	302	*/
	303
	304	/* Memory Bank 0 (Intel Strata Flash) initialization */
6d0f6bcf JCPV	305	#define CONFIG_SYS_EBC_PB0AP 0x92015480
6d0f6bcf JCPV	306	#define CONFIG_SYS_EBC_PB0CR 0xFF87A000 /* BAS=0xFF8,BS=08MB,BU=R/W,BW=16bit*/
a20b27a3 SR	307
a20b27a3 SR	308	/* Memory Bank 1 ( Power TAU) initialization */
6d0f6bcf JCPV	309	/* #define CONFIG_SYS_EBC_PB1AP 0x04041000 */
	310	/* #define CONFIG_SYS_EBC_PB1CR 0xF0018000 / / BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
	311	#define CONFIG_SYS_EBC_PB1AP 0x00000000
	312	#define CONFIG_SYS_EBC_PB1CR 0x00000000
a20b27a3 SR	313
a20b27a3 SR	314	/* Memory Bank 2 (Intel Flash) initialization */
6d0f6bcf JCPV	315	#define CONFIG_SYS_EBC_PB2AP 0x00000000
6d0f6bcf JCPV	316	#define CONFIG_SYS_EBC_PB2CR 0x00000000
a20b27a3 SR	317
a20b27a3 SR	318	/* Memory Bank 3 (NAND) initialization */
6d0f6bcf JCPV	319	#define CONFIG_SYS_EBC_PB3AP 0x92015480
6d0f6bcf JCPV	320	#define CONFIG_SYS_EBC_PB3CR 0xF40B8000 /addr 0xF40, BS=32M,BU=R/W, BW=8bit /
a20b27a3 SR	321
a20b27a3 SR	322	/* Memory Bank 4 (FPGA regs) initialization */
6d0f6bcf JCPV	323	#define CONFIG_SYS_EBC_PB4AP 0x00000000
6d0f6bcf JCPV	324	#define CONFIG_SYS_EBC_PB4CR 0x00000000 /* leave it blank */
a20b27a3	325
6d0f6bcf	326	#define CONFIG_SYS_NAND_BASE 0xF4000000
a20b27a3 SR	327
	328	/*-----------------------------------------------------------------------
	329	* Definitions for initial stack pointer and data area (in data cache)
	330	*/
	331	/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
6d0f6bcf	332	#define CONFIG_SYS_TEMP_STACK_OCM 1
a20b27a3 SR	333
a20b27a3 SR	334	/* On Chip Memory location */
6d0f6bcf JCPV	335	#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
	336	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
	337	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
553f0982	338	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
a20b27a3	339
25ddd1fb	340	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	341	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
a20b27a3 SR	342
	343	/*-----------------------------------------------------------------------
	344	* Definitions for GPIO setup (PPC405EP specific)
	345	*
	346	* GPIO0[0] - External Bus Controller BLAST output
	347	* GPIO0[1-9] - Instruction trace outputs
	348	* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
	349	* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
	350	* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
	351	* GPIO0[24-27] - UART0 control signal inputs/outputs
	352	* GPIO0[28-29] - UART1 data signal input/output
	353	* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
	354	*
	355	* following GPIO setting changed for G20000, 080304
	356	*/
afabb498 SR	357	#define CONFIG_SYS_GPIO0_OSRL 0x40005555
	358	#define CONFIG_SYS_GPIO0_OSRH 0x40000110
	359	#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
	360	#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
6d0f6bcf	361	#define CONFIG_SYS_GPIO0_TSRL 0x00000000
afabb498	362	#define CONFIG_SYS_GPIO0_TSRH 0x00000000
6d0f6bcf	363	#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014
a20b27a3	364
a20b27a3 SR	365	/*
	366	* Default speed selection (cpu_plb_opb_ebc) in mhz.
	367	* This value will be set if iic boot eprom is disabled.
	368	*/
	369	#if 1
	370	#define PLLMR0_DEFAULT PLLMR0_266_66_33_33
	371	#define PLLMR1_DEFAULT PLLMR1_266_66_33_33
	372	#endif
	373	#if 0
	374	#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
	375	#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
	376	#endif
	377	#if 0
	378	#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
	379	#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
	380	#endif
	381	#if 0
	382	#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
	383	#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
	384	#endif
	385
	386	#endif /* __CONFIG_H */