[people/ms/u-boot.git] / include / configs / PLU405.h

/*
 * (C) Copyright 2001-2003
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
#define CONFIG_PLU405		1	/* ...on a PLU405 board		*/

#define	CONFIG_SYS_TEXT_BASE	0xFFF80000

#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/

#define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */

#define CONFIG_BAUDRATE		9600

#undef	CONFIG_BOOTARGS
#undef	CONFIG_BOOTCOMMAND

#define CONFIG_PREBOOT                  /* enable preboot variable      */

#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

#undef  CONFIG_HAS_ETH1

#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII		1	/* MII PHY management		*/
#define CONFIG_PHY_ADDR		0	/* PHY address			*/
#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R      1       /* use reset_phy()              */

#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_NAND
#define CONFIG_CMD_DATE
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_USB

#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP

#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#define CONFIG_SUPPORT_VFAT

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
#define CONFIG_SYS_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address		*/

#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/

#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/

#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/

#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_serial_clock()

#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD	    691200

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
	 57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */

#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */

#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

/* Only interrupt boot if space is pressed */
/* If a long serial cable is connected but */
/* other end is dead, garbage will be read */
#define CONFIG_AUTOBOOT_KEYED	1
#define CONFIG_AUTOBOOT_PROMPT	\
	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
#undef CONFIG_AUTOBOOT_DELAY_STR
#define CONFIG_AUTOBOOT_STOP_STR " "

#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */

/*
 * NAND-FLASH stuff
 */
#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
#define NAND_BIG_DELAY_US	25

#define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
#define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
#define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
#define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */

#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
#define CONFIG_SYS_NAND_QUIET          1

/*
 * PCI stuff
 */
#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
#define PCI_HOST_FORCE  1               /* configure as pci host        */
#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

#define CONFIG_PCI			/* include pci support	        */
#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
					/* resource configuration       */

#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
#define CONFIG_SYS_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
#define CONFIG_SYS_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */

/*
 * IDE/ATA stuff
 */
#undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
#define CONFIG_IDE_RESET	1	/* reset for ide supported	*/

#define CONFIG_SYS_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
/* max. 1 drives per IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*1)

#define CONFIG_SYS_ATA_BASE_ADDR	0xF0100000
#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* Offset for normal register access */
#define CONFIG_SYS_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */

/*
 * FLASH organization
 */
#define FLASH_BASE0_PRELIM	0xFFC00000 /* FLASH bank #0 */

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms) */

#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width) */
#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st addr for flash config cycles */
#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd addr for flash config cycles */
/*
 * The following defines are added for buggy IOP480 byte interface.
 * All other boards should use the standard values (CPCI405 etc.)
 */
#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard */
#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard */
#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard */

#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector */

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN		(~(CONFIG_SYS_TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN		(1024 << 10)

/*
 * Environment Variable setup
 */
#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET		0x100	/* reseve 0x100 bytes for strapping */
#define CONFIG_ENV_SIZE		0x700

/*
 * I2C EEPROM (24WC16) for environment
 */
#define CONFIG_HARD_I2C			/* I2c with hardware support */
#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE		0x7F

#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM 24WC16 */
#define CONFIG_SYS_EEPROM_WREN         1

/* 24WC16 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"    */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The 24WC16 has   */
					/* 16 byte page write mode using */
					/* last 4 bits of the address   */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */

/*
 * External Bus Controller (EBC) Setup
 */
#define CAN0_BA		0xF0000000	    /* CAN0 Base Address	*/
#define CAN1_BA		0xF0000100	    /* CAN1 Base Address	*/
#define DUART0_BA	0xF0000400	    /* DUART Base Address       */
#define DUART1_BA	0xF0000408	    /* DUART Base Address       */
#define RTC_BA		0xF0000500	    /* RTC Base Address         */
#define VGA_BA		0xF1000000	    /* Epson VGA Base Address   */
#define CONFIG_SYS_NAND_BASE	0xF4000000	    /* NAND FLASH Base Address  */

/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
#define CONFIG_SYS_EBC_PB0AP		0x92015480
/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000

/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB1AP		0x92015480
/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB1CR		0xF4018000

/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2AP		0x010053C0
/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB2CR		0xF0018000

/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB3AP		0x010053C0
/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB3CR		0xF011A000

/*
 * FPGA stuff
 */
#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100	    /* FPGA internal Base Address */

/* FPGA internal regs */
#define CONFIG_SYS_FPGA_CTRL		0x000

/* FPGA Control Reg */
#define CONFIG_SYS_FPGA_CTRL_CF_RESET	0x0001
#define CONFIG_SYS_FPGA_CTRL_WDI	0x0002
#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020

#define CONFIG_SYS_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now */
#define CONFIG_SYS_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/

/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output) */
#define CONFIG_SYS_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output) */
#define CONFIG_SYS_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input) */
#define CONFIG_SYS_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input) */

/*
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM	  1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM  */

#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Definitions for GPIO setup (PPC405EP specific)
 *
 * GPIO0[0]	- External Bus Controller BLAST output
 * GPIO0[1-9]	- Instruction trace outputs -> GPIO
 * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 * GPIO0[24-27] - UART0 control signal inputs/outputs
 * GPIO0[28-29] - UART1 data signal input/output
 * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 */
#define CONFIG_SYS_GPIO0_OSRL		0x00000550
#define CONFIG_SYS_GPIO0_OSRH		0x00000110
#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
#define CONFIG_SYS_GPIO0_ISR1H		0x15555445
#define CONFIG_SYS_GPIO0_TSRL		0x00000000
#define CONFIG_SYS_GPIO0_TSRH		0x00000000
#define CONFIG_SYS_GPIO0_TCR		0x77FE0014

#define CONFIG_SYS_DUART_RST		(0x80000000 >> 14)
#define CONFIG_SYS_EEPROM_WP		(0x80000000 >> 0)

/*
 * Default speed selection (cpu_plb_opb_ebc) in MHz.
 * This value will be set if iic boot eprom is disabled.
 */
#if 1
#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
#endif

/*
 * PCI OHCI controller
 */
#define CONFIG_USB_OHCI_NEW	1
#define CONFIG_PCI_OHCI		1
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
#define CONFIG_USB_STORAGE	1

/*
 * UBI
 */
#define CONFIG_CMD_UBI
#define CONFIG_RBTREE
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO

#endif	/* __CONFIG_H */
Commit	Line	Data
13fdf8a6 SR	1	/*
	2	* (C) Copyright 2001-2003
	3	* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
13fdf8a6 SR	6	*/
	7
	8	/*
	9	* board/config.h - configuration options, board specific
	10	*/
	11
	12	#ifndef __CONFIG_H
	13	#define __CONFIG_H
	14
	15	/*
	16	* High Level Configuration Options
	17	* (easy to change)
	18	*/
	19
	20	#define CONFIG_405EP 1 /* This is a PPC405 CPU */
c837dcb1 WD	21	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
c837dcb1 WD	22	#define CONFIG_PLU405 1 /* ...on a PLU405 board */
13fdf8a6	23
2ae18241 WD	24	#define CONFIG_SYS_TEXT_BASE 0xFFF80000
2ae18241 WD	25
c837dcb1 WD	26	#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
c837dcb1 WD	27	#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
13fdf8a6	28
a20b27a3	29	#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
13fdf8a6 SR	30
13fdf8a6 SR	31	#define CONFIG_BAUDRATE 9600
13fdf8a6 SR	32
13fdf8a6 SR	33	#undef CONFIG_BOOTARGS
a20b27a3 SR	34	#undef CONFIG_BOOTCOMMAND
	35
	36	#define CONFIG_PREBOOT /* enable preboot variable */
	37
6d0f6bcf	38	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
13fdf8a6	39
f9fc6a58	40	#undef CONFIG_HAS_ETH1
a20b27a3	41
96e21f86	42	#define CONFIG_PPC4xx_EMAC
13fdf8a6	43	#define CONFIG_MII 1 /* MII PHY management */
c837dcb1	44	#define CONFIG_PHY_ADDR 0 /* PHY address */
a20b27a3	45	#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
9ec367aa	46	#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */
a20b27a3 SR	47
a20b27a3 SR	48	#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
13fdf8a6	49
acf02697	50
a1aa0bb5 JL	51	/*
	52	* BOOTP options
	53	*/
	54	#define CONFIG_BOOTP_BOOTFILESIZE
	55	#define CONFIG_BOOTP_BOOTPATH
	56	#define CONFIG_BOOTP_GATEWAY
	57	#define CONFIG_BOOTP_HOSTNAME
	58
	59
acf02697 JL	60	/*
	61	* Command line configuration.
	62	*/
	63	#include <config_cmd_default.h>
	64
	65	#define CONFIG_CMD_DHCP
	66	#define CONFIG_CMD_PCI
	67	#define CONFIG_CMD_IRQ
	68	#define CONFIG_CMD_IDE
	69	#define CONFIG_CMD_FAT
	70	#define CONFIG_CMD_ELF
	71	#define CONFIG_CMD_NAND
	72	#define CONFIG_CMD_DATE
	73	#define CONFIG_CMD_I2C
	74	#define CONFIG_CMD_MII
	75	#define CONFIG_CMD_PING
	76	#define CONFIG_CMD_EEPROM
17e65c21	77	#define CONFIG_CMD_USB
acf02697	78
3bc1054c MF	79	#define CONFIG_OF_LIBFDT
3bc1054c MF	80	#define CONFIG_OF_BOARD_SETUP
13fdf8a6 SR	81
	82	#define CONFIG_MAC_PARTITION
	83	#define CONFIG_DOS_PARTITION
	84
a20b27a3 SR	85	#define CONFIG_SUPPORT_VFAT
a20b27a3 SR	86
c837dcb1	87	#undef CONFIG_WATCHDOG /* watchdog disabled */
13fdf8a6	88
c837dcb1	89	#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
6d0f6bcf	90	#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
13fdf8a6	91
c837dcb1	92	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
13fdf8a6 SR	93
	94	/*
	95	* Miscellaneous configurable options
	96	*/
6d0f6bcf JCPV	97	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6d0f6bcf JCPV	98	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
13fdf8a6	99
6d0f6bcf	100	#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
13fdf8a6	101
acf02697	102	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	103	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
13fdf8a6	104	#else
6d0f6bcf	105	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
13fdf8a6	106	#endif
6d0f6bcf JCPV	107	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	108	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	109	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
13fdf8a6	110
6d0f6bcf	111	#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
13fdf8a6	112
6d0f6bcf	113	#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
13fdf8a6	114
a20b27a3 SR	115	#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
a20b27a3 SR	116
6d0f6bcf JCPV	117	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
6d0f6bcf JCPV	118	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
13fdf8a6	119
550650dd SR	120	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
	121	#define CONFIG_SYS_NS16550
	122	#define CONFIG_SYS_NS16550_SERIAL
	123	#define CONFIG_SYS_NS16550_REG_SIZE 1
	124	#define CONFIG_SYS_NS16550_CLK get_serial_clock()
	125
6d0f6bcf	126	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
6d0f6bcf	127	#define CONFIG_SYS_BASE_BAUD 691200
13fdf8a6 SR	128
13fdf8a6 SR	129	/* The following table includes the supported baudrates */
6d0f6bcf	130	#define CONFIG_SYS_BAUDRATE_TABLE \
13fdf8a6 SR	131	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
	132	57600, 115200, 230400, 460800, 921600 }
	133
6d0f6bcf JCPV	134	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6d0f6bcf JCPV	135	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
13fdf8a6	136
6d0f6bcf	137	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
13fdf8a6	138
17e65c21	139	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
13fdf8a6	140	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
a20b27a3 SR	141	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
	142
	143	/* Only interrupt boot if space is pressed */
	144	/* If a long serial cable is connected but */
	145	/* other end is dead, garbage will be read */
f2302d44 SR	146	#define CONFIG_AUTOBOOT_KEYED 1
	147	#define CONFIG_AUTOBOOT_PROMPT \
	148	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
a20b27a3 SR	149	#undef CONFIG_AUTOBOOT_DELAY_STR
a20b27a3 SR	150	#define CONFIG_AUTOBOOT_STOP_STR " "
13fdf8a6	151
c837dcb1	152	#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
13fdf8a6	153
6d0f6bcf	154	#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
13fdf8a6	155
9ec367aa	156	/*
13fdf8a6	157	* NAND-FLASH stuff
13fdf8a6	158	*/
6d0f6bcf	159	#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
6d0f6bcf	160	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
bd84ee4c	161	#define NAND_BIG_DELAY_US 25
addb2e16	162
6d0f6bcf JCPV	163	#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
	164	#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
	165	#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
	166	#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
13fdf8a6	167
6d0f6bcf JCPV	168	#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
6d0f6bcf JCPV	169	#define CONFIG_SYS_NAND_QUIET 1
a20b27a3	170
9ec367aa	171	/*
13fdf8a6	172	* PCI stuff
13fdf8a6	173	*/
a20b27a3 SR	174	#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
	175	#define PCI_HOST_FORCE 1 /* configure as pci host */
	176	#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
	177
	178	#define CONFIG_PCI /* include pci support */
842033e6	179	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
17e65c21	180	#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
a20b27a3 SR	181	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	182	/* resource configuration */
	183
	184	#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
	185
	186	#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
	187
6d0f6bcf JCPV	188	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
	189	#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
	190	#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
	191	#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
	192	#define CONFIG_SYS_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */
	193	#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
	194	#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
	195	#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
	196	#define CONFIG_SYS_PCI_PTM2PCI 0x08000000 /* Host: use this pci address */
13fdf8a6	197
9ec367aa	198	/*
13fdf8a6	199	* IDE/ATA stuff
13fdf8a6	200	*/
c837dcb1 WD	201	#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
c837dcb1 WD	202	#undef CONFIG_IDE_LED /* no led for ide supported */
13fdf8a6 SR	203	#define CONFIG_IDE_RESET 1 /* reset for ide supported */
13fdf8a6 SR	204
6d0f6bcf	205	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
9ec367aa	206	/* max. 1 drives per IDE bus */
6d0f6bcf	207	#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1)
13fdf8a6	208
6d0f6bcf JCPV	209	#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
6d0f6bcf JCPV	210	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
13fdf8a6	211
6d0f6bcf JCPV	212	#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
	213	#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */
	214	#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
13fdf8a6 SR	215
	216	/*
	217	* For booting Linux, the board info and command line data
	218	* have to be in the first 8 MB of memory, since this is
	219	* the maximum mapped by the Linux kernel during initialization.
	220	*/
6d0f6bcf	221	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
9ec367aa MF	222
9ec367aa MF	223	/*
13fdf8a6 SR	224	* FLASH organization
13fdf8a6 SR	225	*/
9ec367aa	226	#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
13fdf8a6	227
6d0f6bcf JCPV	228	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
6d0f6bcf JCPV	229	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
13fdf8a6	230
6d0f6bcf JCPV	231	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	232	#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
13fdf8a6	233
6d0f6bcf JCPV	234	#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
	235	#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st addr for flash config cycles */
	236	#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd addr for flash config cycles */
13fdf8a6 SR	237	/*
	238	* The following defines are added for buggy IOP480 byte interface.
	239	* All other boards should use the standard values (CPCI405 etc.)
	240	*/
6d0f6bcf JCPV	241	#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
	242	#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
	243	#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
13fdf8a6	244
6d0f6bcf	245	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */
13fdf8a6	246
9ec367aa	247	/*
13fdf8a6 SR	248	* Start addresses for the final memory configuration
13fdf8a6 SR	249	* (Set up by the startup code)
6d0f6bcf	250	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
13fdf8a6	251	*/
6d0f6bcf	252	#define CONFIG_SYS_SDRAM_BASE 0x00000000
985edacc	253	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
14d0a02a WD	254	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
14d0a02a WD	255	#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
985edacc	256	#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
13fdf8a6	257
9ec367aa	258	/*
13fdf8a6 SR	259	* Environment Variable setup
13fdf8a6 SR	260	*/
bb1f8b4f	261	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
0e8d1586 JCPV	262	#define CONFIG_ENV_OFFSET 0x100 /* reseve 0x100 bytes for strapping */
0e8d1586 JCPV	263	#define CONFIG_ENV_SIZE 0x700
13fdf8a6	264
9ec367aa MF	265	/*
9ec367aa MF	266	* I2C EEPROM (24WC16) for environment
13fdf8a6 SR	267	*/
13fdf8a6 SR	268	#define CONFIG_HARD_I2C /* I2c with hardware support */
d0b0dcaa	269	#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
6d0f6bcf JCPV	270	#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
6d0f6bcf JCPV	271	#define CONFIG_SYS_I2C_SLAVE 0x7F
13fdf8a6	272
6d0f6bcf JCPV	273	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */
6d0f6bcf JCPV	274	#define CONFIG_SYS_EEPROM_WREN 1
bd84ee4c	275
9ec367aa	276	/* 24WC16 */
6d0f6bcf	277	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
9ec367aa	278	/* mask of address bits that overflow into the "EEPROM chip address" */
6d0f6bcf JCPV	279	#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
6d0f6bcf JCPV	280	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The 24WC16 has */
9ec367aa MF	281	/* 16 byte page write mode using */
9ec367aa MF	282	/* last 4 bits of the address */
6d0f6bcf	283	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
13fdf8a6	284
9ec367aa	285	/*
13fdf8a6 SR	286	* External Bus Controller (EBC) Setup
13fdf8a6 SR	287	*/
be0db3e3 MF	288	#define CAN0_BA 0xF0000000 /* CAN0 Base Address */
be0db3e3 MF	289	#define CAN1_BA 0xF0000100 /* CAN1 Base Address */
9ec367aa MF	290	#define DUART0_BA 0xF0000400 /* DUART Base Address */
	291	#define DUART1_BA 0xF0000408 /* DUART Base Address */
	292	#define RTC_BA 0xF0000500 /* RTC Base Address */
	293	#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
6d0f6bcf	294	#define CONFIG_SYS_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
9ec367aa MF	295
	296	/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
	297	/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
6d0f6bcf	298	#define CONFIG_SYS_EBC_PB0AP 0x92015480
9ec367aa	299	/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
6d0f6bcf	300	#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000
13fdf8a6	301
9ec367aa	302	/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
6d0f6bcf	303	#define CONFIG_SYS_EBC_PB1AP 0x92015480
9ec367aa	304	/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
6d0f6bcf	305	#define CONFIG_SYS_EBC_PB1CR 0xF4018000
13fdf8a6	306
9ec367aa MF	307	/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
9ec367aa MF	308	/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
6d0f6bcf	309	#define CONFIG_SYS_EBC_PB2AP 0x010053C0
9ec367aa	310	/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
6d0f6bcf	311	#define CONFIG_SYS_EBC_PB2CR 0xF0018000
13fdf8a6	312
9ec367aa MF	313	/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
9ec367aa MF	314	/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
6d0f6bcf	315	#define CONFIG_SYS_EBC_PB3AP 0x010053C0
9ec367aa	316	/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
6d0f6bcf	317	#define CONFIG_SYS_EBC_PB3CR 0xF011A000
13fdf8a6	318
9ec367aa	319	/*
13fdf8a6 SR	320	* FPGA stuff
13fdf8a6 SR	321	*/
6d0f6bcf	322	#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
13fdf8a6 SR	323
13fdf8a6 SR	324	/* FPGA internal regs */
6d0f6bcf	325	#define CONFIG_SYS_FPGA_CTRL 0x000
13fdf8a6 SR	326
13fdf8a6 SR	327	/* FPGA Control Reg */
6d0f6bcf JCPV	328	#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001
	329	#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002
	330	#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020
13fdf8a6	331
6d0f6bcf JCPV	332	#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
6d0f6bcf JCPV	333	#define CONFIG_SYS_FPGA_MAX_SIZE 1281024 / 128kByte is enough for XC2S50E*/
13fdf8a6 SR	334
13fdf8a6 SR	335	/* FPGA program pin configuration */
6d0f6bcf JCPV	336	#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
	337	#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
	338	#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
	339	#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
	340	#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
13fdf8a6	341
9ec367aa	342	/*
13fdf8a6 SR	343	* Definitions for initial stack pointer and data area (in data cache)
	344	*/
	345	/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
6d0f6bcf	346	#define CONFIG_SYS_TEMP_STACK_OCM 1
13fdf8a6 SR	347
13fdf8a6 SR	348	/* On Chip Memory location */
6d0f6bcf JCPV	349	#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
	350	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
	351	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
553f0982	352	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
13fdf8a6	353
25ddd1fb	354	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	355	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
13fdf8a6	356
9ec367aa	357	/*
13fdf8a6 SR	358	* Definitions for GPIO setup (PPC405EP specific)
13fdf8a6 SR	359	*
c837dcb1 WD	360	* GPIO0[0] - External Bus Controller BLAST output
c837dcb1 WD	361	* GPIO0[1-9] - Instruction trace outputs -> GPIO
13fdf8a6 SR	362	* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
	363	* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
	364	* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
	365	* GPIO0[24-27] - UART0 control signal inputs/outputs
	366	* GPIO0[28-29] - UART1 data signal input/output
	367	* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
	368	*/
afabb498 SR	369	#define CONFIG_SYS_GPIO0_OSRL 0x00000550
	370	#define CONFIG_SYS_GPIO0_OSRH 0x00000110
	371	#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
	372	#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
6d0f6bcf	373	#define CONFIG_SYS_GPIO0_TSRL 0x00000000
afabb498	374	#define CONFIG_SYS_GPIO0_TSRH 0x00000000
6d0f6bcf	375	#define CONFIG_SYS_GPIO0_TCR 0x77FE0014
13fdf8a6	376
6d0f6bcf JCPV	377	#define CONFIG_SYS_DUART_RST (0x80000000 >> 14)
6d0f6bcf JCPV	378	#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0)
13fdf8a6	379
13fdf8a6	380	/*
9ec367aa	381	* Default speed selection (cpu_plb_opb_ebc) in MHz.
13fdf8a6 SR	382	* This value will be set if iic boot eprom is disabled.
13fdf8a6 SR	383	*/
17e65c21	384	#if 1
c837dcb1 WD	385	#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
c837dcb1 WD	386	#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
13fdf8a6 SR	387	#endif
13fdf8a6 SR	388	#if 0
c837dcb1 WD	389	#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
c837dcb1 WD	390	#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
13fdf8a6	391	#endif
17e65c21	392	#if 0
c837dcb1 WD	393	#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
c837dcb1 WD	394	#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
13fdf8a6 SR	395	#endif
13fdf8a6 SR	396
17e65c21 MF	397	/*
	398	* PCI OHCI controller
	399	*/
	400	#define CONFIG_USB_OHCI_NEW 1
	401	#define CONFIG_PCI_OHCI 1
6d0f6bcf JCPV	402	#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
	403	#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
	404	#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
17e65c21 MF	405	#define CONFIG_USB_STORAGE 1
17e65c21 MF	406
985edacc MF	407	/*
	408	* UBI
	409	*/
	410	#define CONFIG_CMD_UBI
	411	#define CONFIG_RBTREE
	412	#define CONFIG_MTD_DEVICE
	413	#define CONFIG_MTD_PARTITIONS
	414	#define CONFIG_CMD_MTDPARTS
	415	#define CONFIG_LZO
	416
13fdf8a6	417	#endif /* __CONFIG_H */