[people/ms/u-boot.git] / include / configs / ds414.h

/*
 * Copyright (C) 2014 Stefan Roese <sr@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _CONFIG_SYNOLOGY_DS414_H
#define _CONFIG_SYNOLOGY_DS414_H

/*
 * High Level Configuration Options (easy to change)
 */
#define CONFIG_DISPLAY_BOARDINFO_LATE

/*
 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
 * for DDR ECC byte filling in the SPL before loading the main
 * U-Boot into it.
 */
#define	CONFIG_SYS_TEXT_BASE	0x00800000
#define CONFIG_SYS_TCLK		250000000	/* 250MHz */

/*
 * Commands configuration
 */
#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
#define CONFIG_CMD_ENV

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE		0x0
#define CONFIG_SYS_I2C_SPEED		100000

/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED		1000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3

/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET		0x7E0000   /* RedBoot config partition in DTS */
#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */

#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
#define CONFIG_PHY_ADDR			{ 0x1, 0x0 }
#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_RGMII

#define CONFIG_SYS_ALT_MEMTEST

/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PCI_ENUM
#define CONFIG_PCI_MVEBU
#define CONFIG_PCI_SCAN_SHOW
#endif

/* USB/EHCI/XHCI configuration */

#define CONFIG_DM_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2

/* FIXME: broken XHCI support
 * Below defines should enable support for the two rear USB3 ports. Sadly, this
 * does not work because:
 * - xhci-pci seems to not support DM_USB, so with that enabled it is not
 *   found.
 * - USB init fails, controller does not respond in time */
#if 0
#undef CONFIG_DM_USB
#define CONFIG_USB_XHCI
#define CONFIG_USB_XHCI_PCI
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#endif

#if !defined(CONFIG_USB_XHCI)
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MARVELL
#define CONFIG_EHCI_IS_TDI
#endif

/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
#define CONFIG_SUPPORT_VFAT
#define CONFIG_SYS_MVFS

/*
 * mv-common.h should be defined after CMD configs since it used them
 * to enable certain macros
 */
#include "mv-common.h"

/*
 * Memory layout while starting into the bin_hdr via the
 * BootROM:
 *
 * 0x4000.4000 - 0x4003.4000	headers space (192KiB)
 * 0x4000.4030			bin_hdr start address
 * 0x4003.4000 - 0x4004.7c00	BootROM memory allocations (15KiB)
 * 0x4007.fffc			BootROM stack top
 *
 * The address space between 0x4007.fffc and 0x400f.fff is not locked in
 * L2 cache thus cannot be used.
 */

/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x40004030
#define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)

#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif

#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT

/* SPL related SPI defines */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS		0
#define CONFIG_SPL_SPI_CS		0
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x24000

/* DS414 bus width is 32bits */
#define CONFIG_DDR_32BIT

/* Use random ethernet address if not configured */
#define CONFIG_LIB_RAND
#define CONFIG_NET_RANDOM_ETHADDR

/* Default Environment */
#define CONFIG_BOOTCOMMAND	"sf read ${loadaddr} 0xd0000 0x700000; bootm"
#define CONFIG_BOOTARGS		"console=ttyS0,115200"
#define CONFIG_LOADADDR		0x80000
#undef CONFIG_PREBOOT		/* override preboot for USB and SPI flash init */
#define CONFIG_PREBOOT		"usb start; sf probe"

#endif /* _CONFIG_SYNOLOGY_DS414_H */
Commit	Line	Data
aefb8f4c PS	1	/*
	2	* Copyright (C) 2014 Stefan Roese <sr@denx.de>
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef _CONFIG_SYNOLOGY_DS414_H
	8	#define _CONFIG_SYNOLOGY_DS414_H
	9
	10	/*
	11	* High Level Configuration Options (easy to change)
	12	*/
	13	#define CONFIG_DISPLAY_BOARDINFO_LATE
	14
	15	/*
	16	* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
	17	* for DDR ECC byte filling in the SPL before loading the main
	18	* U-Boot into it.
	19	*/
	20	#define CONFIG_SYS_TEXT_BASE 0x00800000
	21	#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
	22
	23	/*
	24	* Commands configuration
	25	*/
	26	#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
aefb8f4c	27	#define CONFIG_CMD_ENV
aefb8f4c PS	28
	29	/* I2C */
	30	#define CONFIG_SYS_I2C
	31	#define CONFIG_SYS_I2C_MVTWSI
	32	#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
	33	#define CONFIG_SYS_I2C_SLAVE 0x0
	34	#define CONFIG_SYS_I2C_SPEED 100000
	35
	36	/* SPI NOR flash default params, used by sf commands */
	37	#define CONFIG_SF_DEFAULT_SPEED 1000000
	38	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
	39
	40	/* Environment in SPI NOR flash */
	41	#define CONFIG_ENV_IS_IN_SPI_FLASH
	42	#define CONFIG_ENV_OFFSET 0x7E0000 /* RedBoot config partition in DTS */
	43	#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
	44	#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */
	45
	46	#define CONFIG_PHY_MARVELL /* there is a marvell phy */
	47	#define CONFIG_PHY_ADDR { 0x1, 0x0 }
	48	#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
	49
	50	#define CONFIG_SYS_ALT_MEMTEST
	51
	52	/* PCIe support */
	53	#ifndef CONFIG_SPL_BUILD
	54	#define CONFIG_PCI
	55	#define CONFIG_CMD_PCI
	56	#define CONFIG_CMD_PCI_ENUM
	57	#define CONFIG_PCI_MVEBU
	58	#define CONFIG_PCI_SCAN_SHOW
	59	#endif
	60
	61	/* USB/EHCI/XHCI configuration */
	62
	63	#define CONFIG_DM_USB
	64	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	65
	66	/* FIXME: broken XHCI support
	67	* Below defines should enable support for the two rear USB3 ports. Sadly, this
	68	* does not work because:
	69	* - xhci-pci seems to not support DM_USB, so with that enabled it is not
	70	* found.
	71	* - USB init fails, controller does not respond in time */
	72	#if 0
	73	#undef CONFIG_DM_USB
	74	#define CONFIG_USB_XHCI
	75	#define CONFIG_USB_XHCI_PCI
	76	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
	77	#endif
	78
	79	#if !defined(CONFIG_USB_XHCI)
	80	#define CONFIG_USB_EHCI
	81	#define CONFIG_USB_EHCI_MARVELL
	82	#define CONFIG_EHCI_IS_TDI
	83	#endif
	84
	85	/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
	86	#define CONFIG_USB_STORAGE
	87	#define CONFIG_DOS_PARTITION
	88	#define CONFIG_ISO_PARTITION
	89	#define CONFIG_SUPPORT_VFAT
	90	#define CONFIG_SYS_MVFS
	91
92	/*
93	* mv-common.h should be defined after CMD configs since it used them
94	* to enable certain macros
95	*/
96	#include "mv-common.h"
97
98	/*
99	* Memory layout while starting into the bin_hdr via the
100	* BootROM:
101	*
102	* 0x4000.4000 - 0x4003.4000 headers space (192KiB)
103	* 0x4000.4030 bin_hdr start address
104	* 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
105	* 0x4007.fffc BootROM stack top
106	*
107	* The address space between 0x4007.fffc and 0x400f.fff is not locked in
108	* L2 cache thus cannot be used.
109	*/
110
111	/* SPL */
112	/* Defines for SPL */
113	#define CONFIG_SPL_FRAMEWORK
114	#define CONFIG_SPL_TEXT_BASE 0x40004030
115	#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
116
117	#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
118	#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
119
120	#ifdef CONFIG_SPL_BUILD
121	#define CONFIG_SYS_MALLOC_SIMPLE
122	#endif
123
124	#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
125	#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
126
127	#define CONFIG_SPL_LIBCOMMON_SUPPORT
128	#define CONFIG_SPL_LIBGENERIC_SUPPORT
129	#define CONFIG_SPL_SERIAL_SUPPORT
130	#define CONFIG_SPL_I2C_SUPPORT
131
132	/* SPL related SPI defines */
133	#define CONFIG_SPL_SPI_SUPPORT
134	#define CONFIG_SPL_SPI_FLASH_SUPPORT
135	#define CONFIG_SPL_SPI_LOAD
136	#define CONFIG_SPL_SPI_BUS 0
137	#define CONFIG_SPL_SPI_CS 0
138	#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000
139
140	/* DS414 bus width is 32bits */
141	#define CONFIG_DDR_32BIT
142
143	/* Use random ethernet address if not configured */
144	#define CONFIG_LIB_RAND
145	#define CONFIG_NET_RANDOM_ETHADDR
146
147	/* Default Environment */
148	#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm"
149	#define CONFIG_BOOTARGS "console=ttyS0,115200"
150	#define CONFIG_LOADADDR 0x80000
151	#undef CONFIG_PREBOOT /* override preboot for USB and SPI flash init */
152	#define CONFIG_PREBOOT "usb start; sf probe"
153
154	#endif /* _CONFIG_SYNOLOGY_DS414_H */