[people/ms/u-boot.git] / include / configs / ds414.h

/*
 * Copyright (C) 2014 Stefan Roese <sr@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _CONFIG_SYNOLOGY_DS414_H
#define _CONFIG_SYNOLOGY_DS414_H

/*
 * High Level Configuration Options (easy to change)
 */
#define CONFIG_DISPLAY_BOARDINFO_LATE

/*
 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
 * for DDR ECC byte filling in the SPL before loading the main
 * U-Boot into it.
 */
#define	CONFIG_SYS_TEXT_BASE	0x00800000
#define CONFIG_SYS_TCLK		250000000	/* 250MHz */

/*
 * Commands configuration
 */
#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
#define CONFIG_CMD_I2C
#define CONFIG_CMD_PING
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_CMD_TFTPPUT
#define CONFIG_CMD_TIME
#define CONFIG_CMD_USB

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE		0x0
#define CONFIG_SYS_I2C_SPEED		100000

/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED		1000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3

/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET		0x7E0000   /* RedBoot config partition in DTS */
#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */

#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
#define CONFIG_PHY_ADDR			{ 0x1, 0x0 }
#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_RGMII

#define CONFIG_SYS_ALT_MEMTEST

/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PCI_ENUM
#define CONFIG_PCI_MVEBU
#define CONFIG_PCI_SCAN_SHOW
#endif

/* USB/EHCI/XHCI configuration */

#define CONFIG_DM_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2

/* FIXME: broken XHCI support
 * Below defines should enable support for the two rear USB3 ports. Sadly, this
 * does not work because:
 * - xhci-pci seems to not support DM_USB, so with that enabled it is not
 *   found.
 * - USB init fails, controller does not respond in time */
#if 0
#undef CONFIG_DM_USB
#define CONFIG_USB_XHCI
#define CONFIG_USB_XHCI_PCI
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#endif

#if !defined(CONFIG_USB_XHCI)
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MARVELL
#define CONFIG_EHCI_IS_TDI
#endif

/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
#define CONFIG_SUPPORT_VFAT
#define CONFIG_SYS_MVFS

/*
 * mv-common.h should be defined after CMD configs since it used them
 * to enable certain macros
 */
#include "mv-common.h"

/*
 * Memory layout while starting into the bin_hdr via the
 * BootROM:
 *
 * 0x4000.4000 - 0x4003.4000	headers space (192KiB)
 * 0x4000.4030			bin_hdr start address
 * 0x4003.4000 - 0x4004.7c00	BootROM memory allocations (15KiB)
 * 0x4007.fffc			BootROM stack top
 *
 * The address space between 0x4007.fffc and 0x400f.fff is not locked in
 * L2 cache thus cannot be used.
 */

/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x40004030
#define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)

#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif

#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT

/* SPL related SPI defines */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS		0
#define CONFIG_SPL_SPI_CS		0
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x24000

/* DS414 bus width is 32bits */
#define CONFIG_DDR_32BIT

/* Use random ethernet address if not configured */
#define CONFIG_LIB_RAND
#define CONFIG_NET_RANDOM_ETHADDR

/* Default Environment */
#define CONFIG_BOOTCOMMAND	"sf read ${loadaddr} 0xd0000 0x700000; bootm"
#define CONFIG_BOOTARGS		"console=ttyS0,115200"
#define CONFIG_LOADADDR		0x80000
#undef CONFIG_PREBOOT		/* override preboot for USB and SPI flash init */
#define CONFIG_PREBOOT		"usb start; sf probe"

#endif /* _CONFIG_SYNOLOGY_DS414_H */
Commit	Line	Data
aefb8f4c PS	1	/*
	2	* Copyright (C) 2014 Stefan Roese <sr@denx.de>
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef _CONFIG_SYNOLOGY_DS414_H
	8	#define _CONFIG_SYNOLOGY_DS414_H
	9
	10	/*
	11	* High Level Configuration Options (easy to change)
	12	*/
	13	#define CONFIG_DISPLAY_BOARDINFO_LATE
	14
	15	/*
	16	* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
	17	* for DDR ECC byte filling in the SPL before loading the main
	18	* U-Boot into it.
	19	*/
	20	#define CONFIG_SYS_TEXT_BASE 0x00800000
	21	#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
	22
	23	/*
	24	* Commands configuration
	25	*/
	26	#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
	27	#define CONFIG_CMD_DHCP
	28	#define CONFIG_CMD_ENV
	29	#define CONFIG_CMD_I2C
	30	#define CONFIG_CMD_PING
	31	#define CONFIG_CMD_SF
	32	#define CONFIG_CMD_SPI
	33	#define CONFIG_CMD_TFTPPUT
	34	#define CONFIG_CMD_TIME
	35	#define CONFIG_CMD_USB
	36
	37	/* I2C */
	38	#define CONFIG_SYS_I2C
	39	#define CONFIG_SYS_I2C_MVTWSI
	40	#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
	41	#define CONFIG_SYS_I2C_SLAVE 0x0
	42	#define CONFIG_SYS_I2C_SPEED 100000
	43
	44	/* SPI NOR flash default params, used by sf commands */
	45	#define CONFIG_SF_DEFAULT_SPEED 1000000
	46	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
	47
	48	/* Environment in SPI NOR flash */
	49	#define CONFIG_ENV_IS_IN_SPI_FLASH
	50	#define CONFIG_ENV_OFFSET 0x7E0000 /* RedBoot config partition in DTS */
	51	#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
	52	#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */
	53
	54	#define CONFIG_PHY_MARVELL /* there is a marvell phy */
	55	#define CONFIG_PHY_ADDR { 0x1, 0x0 }
	56	#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
	57
	58	#define CONFIG_SYS_ALT_MEMTEST
	59
	60	/* PCIe support */
	61	#ifndef CONFIG_SPL_BUILD
	62	#define CONFIG_PCI
	63	#define CONFIG_CMD_PCI
	64	#define CONFIG_CMD_PCI_ENUM
65	#define CONFIG_PCI_MVEBU
66	#define CONFIG_PCI_SCAN_SHOW
67	#endif
68
69	/* USB/EHCI/XHCI configuration */
70
71	#define CONFIG_DM_USB
72	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
73
74	/* FIXME: broken XHCI support
75	* Below defines should enable support for the two rear USB3 ports. Sadly, this
76	* does not work because:
77	* - xhci-pci seems to not support DM_USB, so with that enabled it is not
78	* found.
79	* - USB init fails, controller does not respond in time */
80	#if 0
81	#undef CONFIG_DM_USB
82	#define CONFIG_USB_XHCI
83	#define CONFIG_USB_XHCI_PCI
84	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
85	#endif
86
87	#if !defined(CONFIG_USB_XHCI)
88	#define CONFIG_USB_EHCI
89	#define CONFIG_USB_EHCI_MARVELL
90	#define CONFIG_EHCI_IS_TDI
91	#endif
92
93	/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
94	#define CONFIG_USB_STORAGE
95	#define CONFIG_DOS_PARTITION
96	#define CONFIG_ISO_PARTITION
97	#define CONFIG_SUPPORT_VFAT
98	#define CONFIG_SYS_MVFS
99
100	/*
101	* mv-common.h should be defined after CMD configs since it used them
102	* to enable certain macros
103	*/
104	#include "mv-common.h"
105
106	/*
107	* Memory layout while starting into the bin_hdr via the
108	* BootROM:
109	*
110	* 0x4000.4000 - 0x4003.4000 headers space (192KiB)
111	* 0x4000.4030 bin_hdr start address
112	* 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
113	* 0x4007.fffc BootROM stack top
114	*
115	* The address space between 0x4007.fffc and 0x400f.fff is not locked in
116	* L2 cache thus cannot be used.
117	*/
118
119	/* SPL */
120	/* Defines for SPL */
121	#define CONFIG_SPL_FRAMEWORK
122	#define CONFIG_SPL_TEXT_BASE 0x40004030
123	#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
124
125	#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
126	#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
127
128	#ifdef CONFIG_SPL_BUILD
129	#define CONFIG_SYS_MALLOC_SIMPLE
130	#endif
131
132	#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
133	#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
134
135	#define CONFIG_SPL_LIBCOMMON_SUPPORT
136	#define CONFIG_SPL_LIBGENERIC_SUPPORT
137	#define CONFIG_SPL_SERIAL_SUPPORT
138	#define CONFIG_SPL_I2C_SUPPORT
139
140	/* SPL related SPI defines */
141	#define CONFIG_SPL_SPI_SUPPORT
142	#define CONFIG_SPL_SPI_FLASH_SUPPORT
143	#define CONFIG_SPL_SPI_LOAD
144	#define CONFIG_SPL_SPI_BUS 0
145	#define CONFIG_SPL_SPI_CS 0
146	#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000
147
148	/* DS414 bus width is 32bits */
149	#define CONFIG_DDR_32BIT
150
151	/* Use random ethernet address if not configured */
152	#define CONFIG_LIB_RAND
153	#define CONFIG_NET_RANDOM_ETHADDR
154
155	/* Default Environment */
156	#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm"
157	#define CONFIG_BOOTARGS "console=ttyS0,115200"
158	#define CONFIG_LOADADDR 0x80000
159	#undef CONFIG_PREBOOT /* override preboot for USB and SPI flash init */
160	#define CONFIG_PREBOOT "usb start; sf probe"
161
162	#endif /* _CONFIG_SYNOLOGY_DS414_H */