[people/ms/u-boot.git] / include / configs / omap3_sdp3430.h

/*
 * (C) Copyright 2006-2009
 * Texas Instruments Incorporated.
 * Richard Woodruff <r-woodruff2@ti.com>
 * Syed Mohammed Khasim <x0khasim@ti.com>
 * Nishanth Menon <nm@ti.com>
 *
 * Configuration settings for the 3430 TI SDP3430 board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* TODO: REMOVE THE FOLLOWING
 * Retained the following till size.h is removed in u-boot
 */
#include <asm/sizes.h>
/*
 * High Level Configuration Options
 */
#define CONFIG_OMAP		1	/* in a TI OMAP core */
#define CONFIG_OMAP34XX		1	/* which is a 34XX */
#define CONFIG_OMAP3_3430SDP	1	/* working with SDP Rev2 */
#define CONFIG_OMAP_COMMON

#define CONFIG_SDRC	/* The chip has SDRC controller */

#include <asm/arch/cpu.h>		/* get chip and board defs */
#include <asm/arch/omap3.h>

/*
 * NOTE:  these #defines presume standard SDP jumper settings.
 * In particular:
 *  - 26 MHz clock (not 19.2 or 38.4 MHz)
 *  - Boot from 128MB NOR, not NAND or OneNAND
 *
 * At this writing, OMAP3 U-Boot support doesn't permit concurrent
 * support for all the flash types the board supports.
 */
#define CONFIG_DISPLAY_CPUINFO		1
#define CONFIG_DISPLAY_BOARDINFO	1

/* Clock Defines */
#define V_OSCK			26000000	/* Clock output from T2 */
#define V_SCLK			(V_OSCK >> 1)

#define CONFIG_MISC_INIT_R

#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS	1
#define CONFIG_INITRD_TAG		1
#define CONFIG_REVISION_TAG		1

#define CONFIG_OF_LIBFDT		1

/*
 * Size of malloc() pool
 * Total Size Environment - 256k
 * Malloc - add 256k
 */
#define CONFIG_ENV_SIZE			(256 << 10)
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (256 << 10))

/*--------------------------------------------------------------------------*/

/*
 * Hardware drivers
 */

/*
 * TWL4030
 */
#define CONFIG_TWL4030_POWER		1

/*
 * serial port - NS16550 compatible
 */
#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

/* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
 * swapped with UART2 via jumpering.  Downsides of using J8:  it doesn't
 * support UART boot (that's only for UART3); it prevents sharing a Linux
 * kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
 *
 * UART boot uses UART3 on J9, and the SDP user's guide says to use
 * that for console.  Downsides of using J9:  you can't use IRDA too;
 * since UART3 isn't in the CORE power domain, it may be a bit less
 * usable in certain PM-sensitive debug scenarios.
 */
#undef CONSOLE_J9			/* else J8/UART1 (innermost) */

#ifdef CONSOLE_J9
#define CONFIG_CONS_INDEX		3
#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
#define CONFIG_SERIAL3			3	/* UART3 */
#else
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550_COM1		OMAP34XX_UART1
#define CONFIG_SERIAL1			1	/* UART1 */
#endif

#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE			115200
#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
					115200}

/*
 * I2C for power management setup
 */
#define CONFIG_HARD_I2C			1
#define CONFIG_SYS_I2C_SPEED		100000
#define CONFIG_SYS_I2C_SLAVE		1
#define CONFIG_DRIVER_OMAP34XX_I2C	1

/* OMITTED:  single 1 Gbit MT29F1G NAND flash */

/*
 * NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
 */
#define CONFIG_SYS_FLASH_BASE		0x10000000
#define CONFIG_FLASH_CFI_DRIVER		1	/* Use drivers/cfi_flash.c */
#define CONFIG_SYS_FLASH_CFI		1	/* use CFI geometry data */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* ~10x faster writes */
#define CONFIG_SYS_FLASH_PROTECTION	1	/* hardware sector protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO	1	/* flinfo 'E' for empty */
#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
#define CONFIG_SYS_MAX_FLASH_BANKS      1	/* max number of flash banks */

#define CONFIG_SYS_FLASH_CFI_WIDTH	2
#define PHYS_FLASH_SIZE			(128 << 20)
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max sectors on one chip */

/* OMITTED:  single 2 Gbit KFM2G16 OneNAND flash */

#define CONFIG_ENV_IS_IN_FLASH		1
#define CONFIG_SYS_ENV_SECT_SIZE	(256 << 10)
#define CONFIG_ENV_OFFSET		CONFIG_SYS_ENV_SECT_SIZE
#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
/*--------------------------------------------------------------------------*/

/* commands to include */
#include <config_cmd_default.h>

/* Enabled commands */
#define CONFIG_CMD_DHCP		/* DHCP Support			*/
#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
#define CONFIG_CMD_FAT		/* FAT support			*/
#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
#define CONFIG_CMD_MMC		/* MMC support			*/
#define CONFIG_CMD_NET

/* Disabled commands */
#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
#undef CONFIG_CMD_IMLS		/* List all found images	*/

/*--------------------------------------------------------------------------*/
/*
 * MMC boot support
 */

#if defined(CONFIG_CMD_MMC)
#define CONFIG_GENERIC_MMC		1
#define CONFIG_MMC			1
#define CONFIG_OMAP_HSMMC		1
#define CONFIG_DOS_PARTITION		1
#endif

/*----------------------------------------------------------------------------
 * SMSC9115 Ethernet from SMSC9118 family
 *----------------------------------------------------------------------------
 */
#if defined(CONFIG_CMD_NET)

#define CONFIG_LAN91C96
#define CONFIG_LAN91C96_BASE	DEBUG_BASE
#define CONFIG_LAN91C96_EXT_PHY

#define CONFIG_BOOTP_SEND_HOSTNAME
/*
 * BOOTP fields
 */
#define CONFIG_BOOTP_SUBNETMASK		0x00000001
#define CONFIG_BOOTP_GATEWAY		0x00000002
#define CONFIG_BOOTP_HOSTNAME		0x00000004
#define CONFIG_BOOTP_BOOTPATH		0x00000010
#endif /* (CONFIG_CMD_NET) */

/*
 * Environment setup
 *
 * Default boot order:  mmc bootscript, MMC uImage, NOR image.
 * Network booting environment must be configured at site.
 */

/* allow overwriting serial config and ethaddr */
#define CONFIG_ENV_OVERWRITE

#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x82000000\0" \
	"console=ttyS0,115200n8\0" \
	"mmcargs=setenv bootargs console=${console} " \
		"root=/dev/mmcblk0p2 rw " \
		"rootfstype=ext3 rootwait\0" \
	"norargs=setenv bootargs console=${console} " \
		"root=/dev/mtdblock3 rw " \
		"rootfstype=jffs2\0" \
	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
	"bootscript=echo Running bootscript from MMC/SD ...; " \
		"autoscr ${loadaddr}\0" \
	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
	"mmcboot=echo Booting from MMC/SD ...; " \
		"run mmcargs; " \
		"bootm ${loadaddr}\0" \
	"norboot=echo Booting from NOR ...; " \
		"run norargs; " \
		"bootm 0x80000\0" \

#define CONFIG_BOOTCOMMAND \
	"if mmcinit; then " \
		"if run loadbootscript; then " \
			"run bootscript; " \
		"else " \
			"if run loaduimage; then " \
				"run mmcboot; " \
			"else run norboot; " \
			"fi; " \
		"fi; " \
	"else run norboot; fi"

#define CONFIG_AUTO_COMPLETE		1

/*--------------------------------------------------------------------------*/

/*
 * Miscellaneous configurable options
 */

#define CONFIG_SYS_LONGHELP		/* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
#define CONFIG_SYS_PROMPT		"OMAP34XX SDP # "
#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

/* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
 * a basic sanity check ONLY
 * IF you would like to increase coverage, increase the end address
 * or run the test with custom options
 */
#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0 + 0x01000000)
#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + (32 << 20))

/* Default load address */
#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)

/*--------------------------------------------------------------------------*/

/*
 * 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
 * 32KHz clk, or from external sig. This rate is divided by a local divisor.
 */
#define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE	0x800
#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - \
					 GENERATED_GBL_DATA_SIZE)
/*
 * SDRAM Memory Map
 */
#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1

/*--------------------------------------------------------------------------*/

/*
 * NOR FLASH usage ... default nCS0:
 *  - one 256KB sector for U-Boot
 *  - one 256KB sector for its parameters (not all used)
 *  - eight sectors (2 MB) for kernel
 *  - rest for JFFS2
 */

/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN		(256 << 10)

/*
 * NAND FLASH usage ... default nCS1:
 *  - four 128KB sectors for X-Loader
 *  - four 128KB sectors for U-Boot
 *  - two 128KB sector for its parameters
 *  - 32 sectors (4 MB) for kernel
 *  - rest for filesystem
 */

/*
 * OneNAND FLASH usage ... default nCS2:
 *  - four 128KB sectors for X-Loader
 *  - two 128KB sectors for U-Boot
 *  - one 128KB sector for its parameters
 *  - sixteen sectors (2 MB) for kernel
 *  - rest for filesystem
 */

#define CONFIG_SYS_CACHELINE_SIZE	64

#endif				/* __CONFIG_H */
Commit	Line	Data
e63e5904 TR	1	/*
	2	* (C) Copyright 2006-2009
	3	* Texas Instruments Incorporated.
	4	* Richard Woodruff <r-woodruff2@ti.com>
	5	* Syed Mohammed Khasim <x0khasim@ti.com>
	6	* Nishanth Menon <nm@ti.com>
	7	*
	8	* Configuration settings for the 3430 TI SDP3430 board.
	9	*
3765b3e7	10	* SPDX-License-Identifier: GPL-2.0+
e63e5904 TR	11	*/
	12
	13	#ifndef __CONFIG_H
	14	#define __CONFIG_H
	15
	16	/* TODO: REMOVE THE FOLLOWING
	17	* Retained the following till size.h is removed in u-boot
	18	*/
	19	#include <asm/sizes.h>
	20	/*
	21	* High Level Configuration Options
	22	*/
e63e5904 TR	23	#define CONFIG_OMAP 1 /* in a TI OMAP core */
e63e5904 TR	24	#define CONFIG_OMAP34XX 1 /* which is a 34XX */
e63e5904	25	#define CONFIG_OMAP3_3430SDP 1 /* working with SDP Rev2 */
806d2792	26	#define CONFIG_OMAP_COMMON
e63e5904	27
cae377b5 VH	28	#define CONFIG_SDRC /* The chip has SDRC controller */
cae377b5 VH	29
e63e5904 TR	30	#include <asm/arch/cpu.h> /* get chip and board defs */
	31	#include <asm/arch/omap3.h>
	32
	33	/*
	34	* NOTE: these #defines presume standard SDP jumper settings.
	35	* In particular:
	36	* - 26 MHz clock (not 19.2 or 38.4 MHz)
	37	* - Boot from 128MB NOR, not NAND or OneNAND
	38	*
	39	* At this writing, OMAP3 U-Boot support doesn't permit concurrent
	40	* support for all the flash types the board supports.
	41	*/
	42	#define CONFIG_DISPLAY_CPUINFO 1
	43	#define CONFIG_DISPLAY_BOARDINFO 1
	44
	45	/* Clock Defines */
	46	#define V_OSCK 26000000 /* Clock output from T2 */
	47	#define V_SCLK (V_OSCK >> 1)
	48
e63e5904 TR	49	#define CONFIG_MISC_INIT_R
	50
	51	#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
	52	#define CONFIG_SETUP_MEMORY_TAGS 1
	53	#define CONFIG_INITRD_TAG 1
	54	#define CONFIG_REVISION_TAG 1
	55
2fa8ca98 GL	56	#define CONFIG_OF_LIBFDT 1
2fa8ca98 GL	57
e63e5904 TR	58	/*
	59	* Size of malloc() pool
	60	* Total Size Environment - 256k
	61	* Malloc - add 256k
	62	*/
	63	#define CONFIG_ENV_SIZE (256 << 10)
	64	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10))
e63e5904 TR	65
	66	/--------------------------------------------------------------------------/
	67
	68	/*
	69	* Hardware drivers
	70	*/
	71
	72	/*
	73	* TWL4030
	74	*/
	75	#define CONFIG_TWL4030_POWER 1
	76
	77	/*
	78	* serial port - NS16550 compatible
	79	*/
	80	#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
	81
	82	#define CONFIG_SYS_NS16550
	83	#define CONFIG_SYS_NS16550_SERIAL
	84	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	85	#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
	86
	87	/* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
	88	* swapped with UART2 via jumpering. Downsides of using J8: it doesn't
	89	* support UART boot (that's only for UART3); it prevents sharing a Linux
	90	* kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
	91	*
	92	* UART boot uses UART3 on J9, and the SDP user's guide says to use
	93	* that for console. Downsides of using J9: you can't use IRDA too;
	94	* since UART3 isn't in the CORE power domain, it may be a bit less
	95	* usable in certain PM-sensitive debug scenarios.
	96	*/
	97	#undef CONSOLE_J9 /* else J8/UART1 (innermost) */
	98
	99	#ifdef CONSOLE_J9
	100	#define CONFIG_CONS_INDEX 3
	101	#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
	102	#define CONFIG_SERIAL3 3 /* UART3 */
	103	#else
	104	#define CONFIG_CONS_INDEX 1
	105	#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
	106	#define CONFIG_SERIAL1 1 /* UART1 */
	107	#endif
	108
	109	#define CONFIG_ENV_OVERWRITE
	110	#define CONFIG_BAUDRATE 115200
	111	#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
	112	115200}
	113
	114	/*
	115	* I2C for power management setup
	116	*/
	117	#define CONFIG_HARD_I2C 1
	118	#define CONFIG_SYS_I2C_SPEED 100000
	119	#define CONFIG_SYS_I2C_SLAVE 1
e63e5904 TR	120	#define CONFIG_DRIVER_OMAP34XX_I2C 1
	121
	122	/* OMITTED: single 1 Gbit MT29F1G NAND flash */
	123
	124	/*
	125	* NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
	126	*/
	127	#define CONFIG_SYS_FLASH_BASE 0x10000000
	128	#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
	129	#define CONFIG_SYS_FLASH_CFI 1 /* use CFI geometry data */
	130	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster writes */
	131	#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware sector protection */
	132	#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* flinfo 'E' for empty */
	133	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
	134	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
	135
	136	#define CONFIG_SYS_FLASH_CFI_WIDTH 2
	137	#define PHYS_FLASH_SIZE (128 << 20)
	138	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors on one chip */
	139
e63e5904 TR	140	/* OMITTED: single 2 Gbit KFM2G16 OneNAND flash */
	141
	142	#define CONFIG_ENV_IS_IN_FLASH 1
	143	#define CONFIG_SYS_ENV_SECT_SIZE (256 << 10)
	144	#define CONFIG_ENV_OFFSET CONFIG_SYS_ENV_SECT_SIZE
	145	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
	146	/--------------------------------------------------------------------------/
	147
	148	/* commands to include */
	149	#include <config_cmd_default.h>
	150
	151	/* Enabled commands */
	152	#define CONFIG_CMD_DHCP /* DHCP Support */
	153	#define CONFIG_CMD_EXT2 /* EXT2 Support */
	154	#define CONFIG_CMD_FAT /* FAT support */
	155	#define CONFIG_CMD_I2C /* I2C serial bus support */
	156	#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
	157	#define CONFIG_CMD_MMC /* MMC support */
	158	#define CONFIG_CMD_NET
	159
	160	/* Disabled commands */
	161	#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
	162	#undef CONFIG_CMD_IMLS /* List all found images */
	163
	164	/--------------------------------------------------------------------------/
	165	/*
	166	* MMC boot support
	167	*/
	168
	169	#if defined(CONFIG_CMD_MMC)
7cc862be	170	#define CONFIG_GENERIC_MMC 1
e63e5904	171	#define CONFIG_MMC 1
7cc862be	172	#define CONFIG_OMAP_HSMMC 1
e63e5904 TR	173	#define CONFIG_DOS_PARTITION 1
	174	#endif
	175
	176	/*----------------------------------------------------------------------------
	177	* SMSC9115 Ethernet from SMSC9118 family
	178	*----------------------------------------------------------------------------
	179	*/
	180	#if defined(CONFIG_CMD_NET)
	181
a1725999	182	#define CONFIG_LAN91C96
e63e5904 TR	183	#define CONFIG_LAN91C96_BASE DEBUG_BASE
	184	#define CONFIG_LAN91C96_EXT_PHY
	185
	186	#define CONFIG_BOOTP_SEND_HOSTNAME
	187	/*
	188	* BOOTP fields
	189	*/
	190	#define CONFIG_BOOTP_SUBNETMASK 0x00000001
	191	#define CONFIG_BOOTP_GATEWAY 0x00000002
	192	#define CONFIG_BOOTP_HOSTNAME 0x00000004
	193	#define CONFIG_BOOTP_BOOTPATH 0x00000010
	194	#endif /* (CONFIG_CMD_NET) */
	195
	196	/*
	197	* Environment setup
	198	*
	199	* Default boot order: mmc bootscript, MMC uImage, NOR image.
	200	* Network booting environment must be configured at site.
	201	*/
	202
	203	/* allow overwriting serial config and ethaddr */
	204	#define CONFIG_ENV_OVERWRITE
	205
	206	#define CONFIG_EXTRA_ENV_SETTINGS \
	207	"loadaddr=0x82000000\0" \
	208	"console=ttyS0,115200n8\0" \
	209	"mmcargs=setenv bootargs console=${console} " \
	210	"root=/dev/mmcblk0p2 rw " \
	211	"rootfstype=ext3 rootwait\0" \
	212	"norargs=setenv bootargs console=${console} " \
	213	"root=/dev/mtdblock3 rw " \
	214	"rootfstype=jffs2\0" \
	215	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
	216	"bootscript=echo Running bootscript from MMC/SD ...; " \
	217	"autoscr ${loadaddr}\0" \
	218	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
	219	"mmcboot=echo Booting from MMC/SD ...; " \
	220	"run mmcargs; " \
	221	"bootm ${loadaddr}\0" \
	222	"norboot=echo Booting from NOR ...; " \
	223	"run norargs; " \
	224	"bootm 0x80000\0" \
	225
	226	#define CONFIG_BOOTCOMMAND \
	227	"if mmcinit; then " \
	228	"if run loadbootscript; then " \
	229	"run bootscript; " \
	230	"else " \
	231	"if run loaduimage; then " \
	232	"run mmcboot; " \
	233	"else run norboot; " \
	234	"fi; " \
	235	"fi; " \
	236	"else run norboot; fi"
	237
	238	#define CONFIG_AUTO_COMPLETE 1
	239
	240	/--------------------------------------------------------------------------/
	241
	242	/*
	243	* Miscellaneous configurable options
	244	*/
e63e5904 TR	245
	246	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	247	#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
1270ec13	248	#define CONFIG_SYS_PROMPT "OMAP34XX SDP # "
f62b1257	249	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
e63e5904 TR	250	/* Print Buffer Size */
	251	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	252	sizeof(CONFIG_SYS_PROMPT) + 16)
	253	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	254	/* Boot Argument Buffer Size */
	255	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
	256
	257	/* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
	258	* a basic sanity check ONLY
	259	* IF you would like to increase coverage, increase the end address
	260	* or run the test with custom options
	261	*/
	262	#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x01000000)
	263	#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + (32 << 20))
	264
	265	/* Default load address */
	266	#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
	267
	268	/--------------------------------------------------------------------------/
	269
	270	/*
	271	* 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
	272	* 32KHz clk, or from external sig. This rate is divided by a local divisor.
	273	*/
	274	#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
	275	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
e63e5904	276
5ec789f6 DB	277	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	278	#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
	279	#define CONFIG_SYS_INIT_RAM_SIZE 0x800
	280	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
	281	CONFIG_SYS_INIT_RAM_SIZE - \
	282	GENERATED_GBL_DATA_SIZE)
e63e5904 TR	283	/*
	284	* SDRAM Memory Map
	285	*/
	286	#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
	287	#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
e63e5904 TR	288	#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
e63e5904 TR	289
e63e5904 TR	290	/--------------------------------------------------------------------------/
	291
	292	/*
	293	* NOR FLASH usage ... default nCS0:
	294	* - one 256KB sector for U-Boot
	295	* - one 256KB sector for its parameters (not all used)
	296	* - eight sectors (2 MB) for kernel
	297	* - rest for JFFS2
	298	*/
	299
	300	/* Monitor at start of flash */
	301	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	302	#define CONFIG_SYS_MONITOR_LEN (256 << 10)
	303
e63e5904 TR	304	/*
	305	* NAND FLASH usage ... default nCS1:
	306	* - four 128KB sectors for X-Loader
	307	* - four 128KB sectors for U-Boot
	308	* - two 128KB sector for its parameters
	309	* - 32 sectors (4 MB) for kernel
	310	* - rest for filesystem
	311	*/
	312
	313	/*
	314	* OneNAND FLASH usage ... default nCS2:
	315	* - four 128KB sectors for X-Loader
	316	* - two 128KB sectors for U-Boot
	317	* - one 128KB sector for its parameters
	318	* - sixteen sectors (2 MB) for kernel
	319	* - rest for filesystem
	320	*/
	321
8e40852f A	322	#define CONFIG_SYS_CACHELINE_SIZE 64
8e40852f A	323
e63e5904	324	#endif /* __CONFIG_H */