[people/ms/u-boot.git] / include / configs / socfpga_vining_fpga.h

/*
 * Copyright (C) 2015 Marek Vasut <marex@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */
#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
#define __CONFIG_SAMTEC_VINING_FPGA_H__

#include <asm/arch/base_addr_ac5.h>

/* Memory configurations */
#define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on VINING_FPGA */

/* Booting Linux */
#define CONFIG_BOOTFILE		"openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
#define CONFIG_BOOTCOMMAND	"run selboot"
#define CONFIG_LOADADDR		0x01000000
#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR

/* I2C EEPROM */
#ifdef CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_I2C_EEPROM_BUS		0
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
#endif

/*
 * Status LEDs:
 *   0 ... Top Green
 *   1 ... Top Red
 *   2 ... Bottom Green
 *   3 ... Bottom Red
 */

/* Ethernet on SoC (EMAC) */
#if defined(CONFIG_CMD_NET)
#define CONFIG_BOOTP_SEND_HOSTNAME
/* PHY */
#endif

/* Extra Environment */
#define CONFIG_HOSTNAME			socfpga_vining_fpga

/*
 * Active LOW GPIO buttons:
 * A: GPIO 77 ... the button between USB B and ethernet
 * B: GPIO 78 ... the button between USB A ports
 *
 * The logic:
 *  if button B is not pressed, boot normal Linux system immediatelly
 *  if button B is pressed, wait $bootdelay and boot recovery system
 */
#define CONFIG_PREBOOT						\
	"setenv hostname vining-${unit_serial} ; "		\
	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; "	\
	"if gpio input 78 ; then "			\
		"setenv bootdelay 10 ; "		\
		"setenv boottype rcvr ; "		\
	"else "						\
		"setenv bootdelay 5 ; "			\
		"setenv boottype norm ; "		\
	"fi"

#define CONFIG_EXTRA_ENV_SETTINGS \
	"verify=n\0" \
	"consdev=ttyS0\0"						\
	"baudrate=115200\0"						\
	"bootscript=boot.scr\0"						\
	"ubimtdnr=5\0"							\
	"ubimtd=rootfs\0"						\
	"ubipart=ubi0:rootfs\0"						\
	"ubisfcs=1\0"		/* Default is flash at CS#1 */		\
	"netdev=eth0\0"							\
	"hostname=vining_fpga\0"						\
	"kernel_addr_r=0x10000000\0"					\
	"mtdparts_0=ff705000.spi.0:"					\
		"1m(u-boot),"						\
		"64k(env1),"						\
		"64k(env2),"						\
		"256k(samtec1),"					\
		"256k(samtec2),"					\
		"-(rcvrfs)\0"	/* Recovery */				\
	"mtdparts_1=ff705000.spi.1:"					\
		"32m(rootfs),"						\
		"-(userfs)\0"						\
	"update_filename=u-boot-with-spl-dtb.sfp\0"			\
	"update_qspi_offset=0x0\0"					\
	"update_qspi="		/* Update the QSPI firmware */		\
		"if sf probe ; then "					\
		"if tftp ${update_filename} ; then "			\
		"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
		"fi ; "							\
		"fi\0"							\
	"fpga_filename=output_file.rbf\0"				\
	"load_fpga="		/* Load FPGA bitstream */		\
		"if tftp ${fpga_filename} ; then "			\
		"fpga load 0 $loadaddr $filesize ; "			\
		"bridge enable ; "					\
		"fi\0"							\
	"addcons="							\
		"setenv bootargs ${bootargs} "				\
		"console=${consdev},${baudrate}\0"			\
	"addip="							\
		"setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
			"${netmask}:${hostname}:${netdev}:off\0"	\
	"addmisc="							\
		"setenv bootargs ${bootargs} ${miscargs}\0"		\
	"addmtd="							\
		"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; "	\
		"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0"	\
	"addargs=run addcons addmtd addmisc\0"				\
	"ubiload="							\
		"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; "		\
		"ubifsload ${kernel_addr_r} /boot/${bootfile}\0"	\
	"netload="							\
		"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0"	\
	"miscargs=nohlt panic=1\0"					\
	"ubiargs="							\
		"setenv bootargs ubi.mtd=${ubimtdnr} "			\
		"root=${ubipart} rootfstype=ubifs\0"			\
	"nfsargs="							\
		"setenv bootargs root=/dev/nfs rw "			\
			"nfsroot=${serverip}:${rootpath},v3,tcp\0"	\
	"ubi_sfsel="							\
		"if test \"${boottype}\" = \"rcvr\" ; then "		\
			"setenv ubisfcs 0 ; "				\
			"setenv ubimtd rcvrfs ; "			\
			"setenv ubimtdnr 5 ; "				\
			"setenv mtdparts mtdparts=${mtdparts_0} ; "	\
			"setenv mtdids nor0=ff705000.spi.0 ; "		\
			"setenv ubipart ubi0:rootfs ; "			\
		"else "							\
			"setenv ubisfcs 1 ; "				\
			"setenv ubimtd rootfs ; "			\
			"setenv ubimtdnr 6 ; "				\
			"setenv mtdparts mtdparts=${mtdparts_1} ; "	\
			"setenv mtdids nor0=ff705000.spi.1 ; "		\
			"setenv ubipart ubi0:rootfs ; "			\
		"fi ; "							\
		"sf probe 0:${ubisfcs}\0"				\
	"ubi_ubi="							\
		"run ubi_sfsel ubiload ubiargs addargs ; "		\
		"bootm ${kernel_addr_r}\0"				\
	"ubi_nfs="							\
		"run ubiload nfsargs addip addargs ; "			\
		"bootm ${kernel_addr_r}\0"				\
	"net_ubi="							\
		"run netload ubiargs addargs ; "			\
		"bootm ${kernel_addr_r}\0"				\
	"net_nfs="							\
		"run netload nfsargs addip addargs ; "			\
		"bootm ${kernel_addr_r}\0"				\
	"selboot="	/* Select from where to boot. */		\
		"if test \"${bootmode}\" = \"qspi\" ; then "		\
			"led all off ; "				\
			"if test \"${boottype}\" = \"rcvr\" ; then "	\
				"echo \"Booting recovery system\" ; "	\
				"led 3 on ; "	/* Bottom RED */	\
			"fi ; "						\
			"led 1 on ; "		/* Top RED */		\
			"run ubi_ubi ; "				\
		"else echo \"Unsupported boot mode: \"${bootmode} ; "	\
		"fi\0"							\

#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
#define CONFIG_ENV_OFFSET		0x100000
#define CONFIG_ENV_OFFSET_REDUND	\
	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)

#define CONFIG_MISC_INIT_R

/* Support changing the prompt string */
#define CONFIG_CMDLINE_PS_SUPPORT

/* The rest of the configuration is shared */
#include <configs/socfpga_common.h>

#endif	/* __CONFIG_SAMTEC_VINING_FPGA_H__ */
Commit	Line	Data
569a191a MV	1	/*
	2	* Copyright (C) 2015 Marek Vasut <marex@denx.de>
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6	#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
	7	#define __CONFIG_SAMTEC_VINING_FPGA_H__
	8
	9	#include <asm/arch/base_addr_ac5.h>
	10
569a191a MV	11	/* Memory configurations */
	12	#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on VINING_FPGA */
	13
	14	/* Booting Linux */
569a191a	15	#define CONFIG_BOOTFILE "openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
569a191a MV	16	#define CONFIG_BOOTCOMMAND "run selboot"
	17	#define CONFIG_LOADADDR 0x01000000
	18	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	19
	20	/* I2C EEPROM */
	21	#ifdef CONFIG_CMD_EEPROM
	22	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	23	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	24	#define CONFIG_SYS_I2C_EEPROM_BUS 0
	25	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	26	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
	27	#endif
	28
	29	/*
	30	* Status LEDs:
	31	* 0 ... Top Green
	32	* 1 ... Top Red
	33	* 2 ... Bottom Green
	34	* 3 ... Bottom Red
	35	*/
569a191a MV	36
	37	/* Ethernet on SoC (EMAC) */
	38	#if defined(CONFIG_CMD_NET)
	39	#define CONFIG_BOOTP_SEND_HOSTNAME
	40	/* PHY */
569a191a MV	41	#endif
	42
	43	/* Extra Environment */
	44	#define CONFIG_HOSTNAME socfpga_vining_fpga
	45
	46	/*
	47	* Active LOW GPIO buttons:
	48	* A: GPIO 77 ... the button between USB B and ethernet
	49	* B: GPIO 78 ... the button between USB A ports
	50	*
	51	* The logic:
	52	* if button B is not pressed, boot normal Linux system immediatelly
	53	* if button B is pressed, wait $bootdelay and boot recovery system
	54	*/
	55	#define CONFIG_PREBOOT \
	56	"setenv hostname vining-${unit_serial} ; " \
	57	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; " \
	58	"if gpio input 78 ; then " \
	59	"setenv bootdelay 10 ; " \
	60	"setenv boottype rcvr ; " \
	61	"else " \
	62	"setenv bootdelay 5 ; " \
	63	"setenv boottype norm ; " \
	64	"fi"
	65
	66	#define CONFIG_EXTRA_ENV_SETTINGS \
	67	"verify=n\0" \
	68	"consdev=ttyS0\0" \
	69	"baudrate=115200\0" \
	70	"bootscript=boot.scr\0" \
	71	"ubimtdnr=5\0" \
	72	"ubimtd=rootfs\0" \
	73	"ubipart=ubi0:rootfs\0" \
	74	"ubisfcs=1\0" /* Default is flash at CS#1 */ \
	75	"netdev=eth0\0" \
	76	"hostname=vining_fpga\0" \
	77	"kernel_addr_r=0x10000000\0" \
	78	"mtdparts_0=ff705000.spi.0:" \
	79	"1m(u-boot)," \
	80	"64k(env1)," \
	81	"64k(env2)," \
	82	"256k(samtec1)," \
	83	"256k(samtec2)," \
	84	"-(rcvrfs)\0" /* Recovery */ \
	85	"mtdparts_1=ff705000.spi.1:" \
	86	"32m(rootfs)," \
	87	"-(userfs)\0" \
	88	"update_filename=u-boot-with-spl-dtb.sfp\0" \
	89	"update_qspi_offset=0x0\0" \
	90	"update_qspi=" /* Update the QSPI firmware */ \
	91	"if sf probe ; then " \
	92	"if tftp ${update_filename} ; then " \
	93	"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
	94	"fi ; " \
	95	"fi\0" \
	96	"fpga_filename=output_file.rbf\0" \
	97	"load_fpga=" /* Load FPGA bitstream */ \
	98	"if tftp ${fpga_filename} ; then " \
	99	"fpga load 0 $loadaddr $filesize ; " \
	100	"bridge enable ; " \
	101	"fi\0" \
	102	"addcons=" \
	103	"setenv bootargs ${bootargs} " \
	104	"console=${consdev},${baudrate}\0" \
105	"addip=" \
106	"setenv bootargs ${bootargs} " \
107	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
108	"${netmask}:${hostname}:${netdev}:off\0" \
109	"addmisc=" \
110	"setenv bootargs ${bootargs} ${miscargs}\0" \
111	"addmtd=" \
112	"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; " \
113	"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \
114	"addargs=run addcons addmtd addmisc\0" \
115	"ubiload=" \
116	"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; " \
117	"ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \
118	"netload=" \
119	"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
120	"miscargs=nohlt panic=1\0" \
121	"ubiargs=" \
122	"setenv bootargs ubi.mtd=${ubimtdnr} " \
123	"root=${ubipart} rootfstype=ubifs\0" \
124	"nfsargs=" \
125	"setenv bootargs root=/dev/nfs rw " \
126	"nfsroot=${serverip}:${rootpath},v3,tcp\0" \
127	"ubi_sfsel=" \
128	"if test \"${boottype}\" = \"rcvr\" ; then " \
129	"setenv ubisfcs 0 ; " \
130	"setenv ubimtd rcvrfs ; " \
131	"setenv ubimtdnr 5 ; " \
132	"setenv mtdparts mtdparts=${mtdparts_0} ; " \
133	"setenv mtdids nor0=ff705000.spi.0 ; " \
134	"setenv ubipart ubi0:rootfs ; " \
135	"else " \
136	"setenv ubisfcs 1 ; " \
137	"setenv ubimtd rootfs ; " \
138	"setenv ubimtdnr 6 ; " \
139	"setenv mtdparts mtdparts=${mtdparts_1} ; " \
140	"setenv mtdids nor0=ff705000.spi.1 ; " \
141	"setenv ubipart ubi0:rootfs ; " \
142	"fi ; " \
143	"sf probe 0:${ubisfcs}\0" \
144	"ubi_ubi=" \
145	"run ubi_sfsel ubiload ubiargs addargs ; " \
146	"bootm ${kernel_addr_r}\0" \
147	"ubi_nfs=" \
148	"run ubiload nfsargs addip addargs ; " \
149	"bootm ${kernel_addr_r}\0" \
150	"net_ubi=" \
151	"run netload ubiargs addargs ; " \
152	"bootm ${kernel_addr_r}\0" \
153	"net_nfs=" \
154	"run netload nfsargs addip addargs ; " \
155	"bootm ${kernel_addr_r}\0" \
156	"selboot=" /* Select from where to boot. */ \
157	"if test \"${bootmode}\" = \"qspi\" ; then " \
158	"led all off ; " \
159	"if test \"${boottype}\" = \"rcvr\" ; then " \
160	"echo \"Booting recovery system\" ; " \
161	"led 3 on ; " /* Bottom RED */ \
162	"fi ; " \
163	"led 1 on ; " /* Top RED */ \
164	"run ubi_ubi ; " \
165	"else echo \"Unsupported boot mode: \"${bootmode} ; " \
166	"fi\0" \
167
569a191a MV	168	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	169	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	170	#define CONFIG_ENV_SECT_SIZE (64 * 1024)
	171	#define CONFIG_ENV_OFFSET 0x100000
	172	#define CONFIG_ENV_OFFSET_REDUND \
	173	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
	174
	175	#define CONFIG_MISC_INIT_R
569a191a	176
569a191a MV	177	/* Support changing the prompt string */
	178	#define CONFIG_CMDLINE_PS_SUPPORT
	179
	180	/* The rest of the configuration is shared */
	181	#include <configs/socfpga_common.h>
	182
	183	#endif /* __CONFIG_SAMTEC_VINING_FPGA_H__ */