[people/ms/u-boot.git] / include / configs / socfpga_vining_fpga.h

/*
 * Copyright (C) 2015 Marek Vasut <marex@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */
#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
#define __CONFIG_SAMTEC_VINING_FPGA_H__

#include <asm/arch/base_addr_ac5.h>

/* U-Boot Commands */
#define CONFIG_FAT_WRITE
#define CONFIG_HW_WATCHDOG

#define CONFIG_CMD_EEPROM

/* Memory configurations */
#define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on VINING_FPGA */

/* Booting Linux */
#define CONFIG_BOOTFILE		"openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
#define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
#define CONFIG_BOOTCOMMAND	"run selboot"
#define CONFIG_LOADADDR		0x01000000
#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR

/* I2C EEPROM */
#ifdef CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_I2C_EEPROM_BUS		0
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
#endif

/*
 * Status LEDs:
 *   0 ... Top Green
 *   1 ... Top Red
 *   2 ... Bottom Green
 *   3 ... Bottom Red
 */

/* Ethernet on SoC (EMAC) */
#if defined(CONFIG_CMD_NET)
#define CONFIG_BOOTP_SEND_HOSTNAME
/* PHY */
#define CONFIG_PHY_MICREL
#define CONFIG_PHY_MICREL_KSZ9021
#endif

/* Extra Environment */
#define CONFIG_HOSTNAME			socfpga_vining_fpga

/*
 * Active LOW GPIO buttons:
 * A: GPIO 77 ... the button between USB B and ethernet
 * B: GPIO 78 ... the button between USB A ports
 *
 * The logic:
 *  if button B is not pressed, boot normal Linux system immediatelly
 *  if button B is pressed, wait $bootdelay and boot recovery system
 */
#define CONFIG_PREBOOT						\
	"setenv hostname vining-${unit_serial} ; "		\
	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; "	\
	"if gpio input 78 ; then "			\
		"setenv bootdelay 10 ; "		\
		"setenv boottype rcvr ; "		\
	"else "						\
		"setenv bootdelay 5 ; "			\
		"setenv boottype norm ; "		\
	"fi"

#define CONFIG_EXTRA_ENV_SETTINGS \
	"verify=n\0" \
	"consdev=ttyS0\0"						\
	"baudrate=115200\0"						\
	"bootscript=boot.scr\0"						\
	"ubimtdnr=5\0"							\
	"ubimtd=rootfs\0"						\
	"ubipart=ubi0:rootfs\0"						\
	"ubisfcs=1\0"		/* Default is flash at CS#1 */		\
	"netdev=eth0\0"							\
	"hostname=vining_fpga\0"						\
	"kernel_addr_r=0x10000000\0"					\
	"mtdparts_0=ff705000.spi.0:"					\
		"1m(u-boot),"						\
		"64k(env1),"						\
		"64k(env2),"						\
		"256k(samtec1),"					\
		"256k(samtec2),"					\
		"-(rcvrfs)\0"	/* Recovery */				\
	"mtdparts_1=ff705000.spi.1:"					\
		"32m(rootfs),"						\
		"-(userfs)\0"						\
	"update_filename=u-boot-with-spl-dtb.sfp\0"			\
	"update_qspi_offset=0x0\0"					\
	"update_qspi="		/* Update the QSPI firmware */		\
		"if sf probe ; then "					\
		"if tftp ${update_filename} ; then "			\
		"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
		"fi ; "							\
		"fi\0"							\
	"fpga_filename=output_file.rbf\0"				\
	"load_fpga="		/* Load FPGA bitstream */		\
		"if tftp ${fpga_filename} ; then "			\
		"fpga load 0 $loadaddr $filesize ; "			\
		"bridge enable ; "					\
		"fi\0"							\
	"addcons="							\
		"setenv bootargs ${bootargs} "				\
		"console=${consdev},${baudrate}\0"			\
	"addip="							\
		"setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
			"${netmask}:${hostname}:${netdev}:off\0"	\
	"addmisc="							\
		"setenv bootargs ${bootargs} ${miscargs}\0"		\
	"addmtd="							\
		"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; "	\
		"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0"	\
	"addargs=run addcons addmtd addmisc\0"				\
	"ubiload="							\
		"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; "		\
		"ubifsload ${kernel_addr_r} /boot/${bootfile}\0"	\
	"netload="							\
		"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0"	\
	"miscargs=nohlt panic=1\0"					\
	"ubiargs="							\
		"setenv bootargs ubi.mtd=${ubimtdnr} "			\
		"root=${ubipart} rootfstype=ubifs\0"			\
	"nfsargs="							\
		"setenv bootargs root=/dev/nfs rw "			\
			"nfsroot=${serverip}:${rootpath},v3,tcp\0"	\
	"ubi_sfsel="							\
		"if test \"${boottype}\" = \"rcvr\" ; then "		\
			"setenv ubisfcs 0 ; "				\
			"setenv ubimtd rcvrfs ; "			\
			"setenv ubimtdnr 5 ; "				\
			"setenv mtdparts mtdparts=${mtdparts_0} ; "	\
			"setenv mtdids nor0=ff705000.spi.0 ; "		\
			"setenv ubipart ubi0:rootfs ; "			\
		"else "							\
			"setenv ubisfcs 1 ; "				\
			"setenv ubimtd rootfs ; "			\
			"setenv ubimtdnr 6 ; "				\
			"setenv mtdparts mtdparts=${mtdparts_1} ; "	\
			"setenv mtdids nor0=ff705000.spi.1 ; "		\
			"setenv ubipart ubi0:rootfs ; "			\
		"fi ; "							\
		"sf probe 0:${ubisfcs}\0"				\
	"ubi_ubi="							\
		"run ubi_sfsel ubiload ubiargs addargs ; "		\
		"bootm ${kernel_addr_r}\0"				\
	"ubi_nfs="							\
		"run ubiload nfsargs addip addargs ; "			\
		"bootm ${kernel_addr_r}\0"				\
	"net_ubi="							\
		"run netload ubiargs addargs ; "			\
		"bootm ${kernel_addr_r}\0"				\
	"net_nfs="							\
		"run netload nfsargs addip addargs ; "			\
		"bootm ${kernel_addr_r}\0"				\
	"selboot="	/* Select from where to boot. */		\
		"if test \"${bootmode}\" = \"qspi\" ; then "		\
			"led all off ; "				\
			"if test \"${boottype}\" = \"rcvr\" ; then "	\
				"echo \"Booting recovery system\" ; "	\
				"led 3 on ; "	/* Bottom RED */	\
			"fi ; "						\
			"led 1 on ; "		/* Top RED */		\
			"run ubi_ubi ; "				\
		"else echo \"Unsupported boot mode: \"${bootmode} ; "	\
		"fi\0"							\

#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_LZO
#define MTDPARTS_DEFAULT			\
	"mtdparts=ff705000.spi.0:"		\
		"1m(u-boot),"			\
		"64k(env1),"			\
		"64k(env2),"			\
		"256k(samtec1),"		\
		"256k(samtec2),"		\
		"-(rcvrfs);"	/* Recovery */	\

#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
#define CONFIG_ENV_OFFSET		0x100000
#define CONFIG_ENV_OFFSET_REDUND	\
	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)

#define CONFIG_MISC_INIT_R

/* Support changing the prompt string */
#define CONFIG_CMDLINE_PS_SUPPORT

/* The rest of the configuration is shared */
#include <configs/socfpga_common.h>

#endif	/* __CONFIG_SAMTEC_VINING_FPGA_H__ */
Commit	Line	Data
569a191a MV	1	/*
	2	* Copyright (C) 2015 Marek Vasut <marex@denx.de>
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6	#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
	7	#define __CONFIG_SAMTEC_VINING_FPGA_H__
	8
	9	#include <asm/arch/base_addr_ac5.h>
	10
	11	/* U-Boot Commands */
569a191a MV	12	#define CONFIG_FAT_WRITE
	13	#define CONFIG_HW_WATCHDOG
	14
	15	#define CONFIG_CMD_EEPROM
569a191a MV	16
	17	/* Memory configurations */
	18	#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on VINING_FPGA */
	19
	20	/* Booting Linux */
569a191a MV	21	#define CONFIG_BOOTFILE "openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
	22	#define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE)
	23	#define CONFIG_BOOTCOMMAND "run selboot"
	24	#define CONFIG_LOADADDR 0x01000000
	25	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	26
	27	/* I2C EEPROM */
	28	#ifdef CONFIG_CMD_EEPROM
	29	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	30	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	31	#define CONFIG_SYS_I2C_EEPROM_BUS 0
	32	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	33	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
	34	#endif
	35
	36	/*
	37	* Status LEDs:
	38	* 0 ... Top Green
	39	* 1 ... Top Red
	40	* 2 ... Bottom Green
	41	* 3 ... Bottom Red
	42	*/
569a191a MV	43
	44	/* Ethernet on SoC (EMAC) */
	45	#if defined(CONFIG_CMD_NET)
	46	#define CONFIG_BOOTP_SEND_HOSTNAME
	47	/* PHY */
	48	#define CONFIG_PHY_MICREL
	49	#define CONFIG_PHY_MICREL_KSZ9021
	50	#endif
	51
	52	/* Extra Environment */
	53	#define CONFIG_HOSTNAME socfpga_vining_fpga
	54
	55	/*
	56	* Active LOW GPIO buttons:
	57	* A: GPIO 77 ... the button between USB B and ethernet
	58	* B: GPIO 78 ... the button between USB A ports
	59	*
	60	* The logic:
	61	* if button B is not pressed, boot normal Linux system immediatelly
	62	* if button B is pressed, wait $bootdelay and boot recovery system
	63	*/
	64	#define CONFIG_PREBOOT \
	65	"setenv hostname vining-${unit_serial} ; " \
	66	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; " \
	67	"if gpio input 78 ; then " \
	68	"setenv bootdelay 10 ; " \
	69	"setenv boottype rcvr ; " \
	70	"else " \
	71	"setenv bootdelay 5 ; " \
	72	"setenv boottype norm ; " \
	73	"fi"
	74
	75	#define CONFIG_EXTRA_ENV_SETTINGS \
	76	"verify=n\0" \
	77	"consdev=ttyS0\0" \
	78	"baudrate=115200\0" \
	79	"bootscript=boot.scr\0" \
	80	"ubimtdnr=5\0" \
	81	"ubimtd=rootfs\0" \
	82	"ubipart=ubi0:rootfs\0" \
	83	"ubisfcs=1\0" /* Default is flash at CS#1 */ \
	84	"netdev=eth0\0" \
	85	"hostname=vining_fpga\0" \
	86	"kernel_addr_r=0x10000000\0" \
	87	"mtdparts_0=ff705000.spi.0:" \
	88	"1m(u-boot)," \
	89	"64k(env1)," \
	90	"64k(env2)," \
	91	"256k(samtec1)," \
	92	"256k(samtec2)," \
	93	"-(rcvrfs)\0" /* Recovery */ \
	94	"mtdparts_1=ff705000.spi.1:" \
	95	"32m(rootfs)," \
	96	"-(userfs)\0" \
	97	"update_filename=u-boot-with-spl-dtb.sfp\0" \
	98	"update_qspi_offset=0x0\0" \
	99	"update_qspi=" /* Update the QSPI firmware */ \
	100	"if sf probe ; then " \
	101	"if tftp ${update_filename} ; then " \
	102	"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
	103	"fi ; " \
	104	"fi\0" \
	105	"fpga_filename=output_file.rbf\0" \
	106	"load_fpga=" /* Load FPGA bitstream */ \
107	"if tftp ${fpga_filename} ; then " \
108	"fpga load 0 $loadaddr $filesize ; " \
109	"bridge enable ; " \
110	"fi\0" \
111	"addcons=" \
112	"setenv bootargs ${bootargs} " \
113	"console=${consdev},${baudrate}\0" \
114	"addip=" \
115	"setenv bootargs ${bootargs} " \
116	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
117	"${netmask}:${hostname}:${netdev}:off\0" \
118	"addmisc=" \
119	"setenv bootargs ${bootargs} ${miscargs}\0" \
120	"addmtd=" \
121	"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; " \
122	"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \
123	"addargs=run addcons addmtd addmisc\0" \
124	"ubiload=" \
125	"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; " \
126	"ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \
127	"netload=" \
128	"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
129	"miscargs=nohlt panic=1\0" \
130	"ubiargs=" \
131	"setenv bootargs ubi.mtd=${ubimtdnr} " \
132	"root=${ubipart} rootfstype=ubifs\0" \
133	"nfsargs=" \
134	"setenv bootargs root=/dev/nfs rw " \
135	"nfsroot=${serverip}:${rootpath},v3,tcp\0" \
136	"ubi_sfsel=" \
137	"if test \"${boottype}\" = \"rcvr\" ; then " \
138	"setenv ubisfcs 0 ; " \
139	"setenv ubimtd rcvrfs ; " \
140	"setenv ubimtdnr 5 ; " \
141	"setenv mtdparts mtdparts=${mtdparts_0} ; " \
142	"setenv mtdids nor0=ff705000.spi.0 ; " \
143	"setenv ubipart ubi0:rootfs ; " \
144	"else " \
145	"setenv ubisfcs 1 ; " \
146	"setenv ubimtd rootfs ; " \
147	"setenv ubimtdnr 6 ; " \
148	"setenv mtdparts mtdparts=${mtdparts_1} ; " \
149	"setenv mtdids nor0=ff705000.spi.1 ; " \
150	"setenv ubipart ubi0:rootfs ; " \
151	"fi ; " \
152	"sf probe 0:${ubisfcs}\0" \
153	"ubi_ubi=" \
154	"run ubi_sfsel ubiload ubiargs addargs ; " \
155	"bootm ${kernel_addr_r}\0" \
156	"ubi_nfs=" \
157	"run ubiload nfsargs addip addargs ; " \
158	"bootm ${kernel_addr_r}\0" \
159	"net_ubi=" \
160	"run netload ubiargs addargs ; " \
161	"bootm ${kernel_addr_r}\0" \
162	"net_nfs=" \
163	"run netload nfsargs addip addargs ; " \
164	"bootm ${kernel_addr_r}\0" \
165	"selboot=" /* Select from where to boot. */ \
166	"if test \"${bootmode}\" = \"qspi\" ; then " \
167	"led all off ; " \
168	"if test \"${boottype}\" = \"rcvr\" ; then " \
169	"echo \"Booting recovery system\" ; " \
170	"led 3 on ; " /* Bottom RED */ \
171	"fi ; " \
172	"led 1 on ; " /* Top RED */ \
173	"run ubi_ubi ; " \
174	"else echo \"Unsupported boot mode: \"${bootmode} ; " \
175	"fi\0" \
176
569a191a	177	#define CONFIG_CMD_UBIFS
569a191a MV	178	#define CONFIG_RBTREE
	179	#define CONFIG_LZO
	180	#define MTDPARTS_DEFAULT \
	181	"mtdparts=ff705000.spi.0:" \
	182	"1m(u-boot)," \
	183	"64k(env1)," \
	184	"64k(env2)," \
	185	"256k(samtec1)," \
	186	"256k(samtec2)," \
	187	"-(rcvrfs);" /* Recovery */ \
	188
	189	#define CONFIG_ENV_IS_IN_SPI_FLASH
	190	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	191	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	192	#define CONFIG_ENV_SECT_SIZE (64 * 1024)
	193	#define CONFIG_ENV_OFFSET 0x100000
	194	#define CONFIG_ENV_OFFSET_REDUND \
	195	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
	196
	197	#define CONFIG_MISC_INIT_R
569a191a	198
569a191a MV	199	/* Support changing the prompt string */
	200	#define CONFIG_CMDLINE_PS_SUPPORT
	201
	202	/* The rest of the configuration is shared */
	203	#include <configs/socfpga_common.h>
	204
	205	#endif /* __CONFIG_SAMTEC_VINING_FPGA_H__ */