arch/arm/Kconfig

   1 menu "ARM architecture"
   2         depends on ARM
   3
   4 config SYS_ARCH
   5         default "arm"
   6
   7 config ARM64
   8         bool
   9         select PHYS_64BIT
  10         select SYS_CACHE_SHIFT_6
  11
  12 if ARM64
  13 config POSITION_INDEPENDENT
  14         bool "Generate position-independent pre-relocation code"
  15         help
  16           U-Boot expects to be linked to a specific hard-coded address, and to
  17           be loaded to and run from that address. This option lifts that
  18           restriction, thus allowing the code to be loaded to and executed
  19           from almost any address. This logic relies on the relocation
  20           information that is embedded into the binary to support U-Boot
  21           relocating itself to the top-of-RAM later during execution.
  22
  23 config SYS_INIT_SP_BSS_OFFSET
  24         int
  25         help
  26           U-Boot typically uses a hard-coded value for the stack pointer
  27           before relocation. Define this option to instead calculate the
  28           initial SP at run-time. This is useful to avoid hard-coding addresses
  29           into U-Boot, so that can be loaded and executed at arbitrary
  30           addresses and thus avoid using arbitrary addresses at runtime. This
  31           option's value is the offset added to &_bss_start in order to
  32           calculate the stack pointer. This offset should be large enough so
  33           that the early malloc region, global data (gd), and early stack usage
  34           do not overlap any appended DTB.
  35
  36 config LINUX_KERNEL_IMAGE_HEADER
  37         bool
  38         help
  39           Place a Linux kernel image header at the start of the U-Boot binary.
  40           The format of the header is described in the Linux kernel source at
  41           Documentation/arm64/booting.txt. This feature is useful since the
  42           image header reports the amount of memory (BSS and similar) that
  43           U-Boot needs to use, but which isn't part of the binary.
  44
  45 if LINUX_KERNEL_IMAGE_HEADER
  46 config LNX_KRNL_IMG_TEXT_OFFSET_BASE
  47         hex
  48         help
  49           The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the
  50           TEXT_OFFSET value written in to the Linux kernel image header.
  51 endif
  52 endif
  53
  54 config STATIC_RELA
  55         bool
  56         default y if ARM64 && !POSITION_INDEPENDENT
  57
  58 config DMA_ADDR_T_64BIT
  59         bool
  60         default y if ARM64
  61
  62 config HAS_VBAR
  63         bool
  64
  65 config HAS_THUMB2
  66         bool
  67
  68 # Used for compatibility with asm files copied from the kernel
  69 config ARM_ASM_UNIFIED
  70         bool
  71         default y
  72
  73 # Used for compatibility with asm files copied from the kernel
  74 config THUMB2_KERNEL
  75         bool
  76
  77 # If set, the workarounds for these ARM errata are applied early during U-Boot
  78 # startup. Note that in general these options force the workarounds to be
  79 # applied; no CPU-type/version detection exists, unlike the similar options in
  80 # the Linux kernel. Do not set these options unless they apply!  Also note that
  81 # the following can be machine specific errata. These do have ability to
  82 # provide rudimentary version and machine specific checks, but expect no
  83 # product checks:
  84 # CONFIG_ARM_ERRATA_430973
  85 # CONFIG_ARM_ERRATA_454179
  86 # CONFIG_ARM_ERRATA_621766
  87 # CONFIG_ARM_ERRATA_798870
  88 # CONFIG_ARM_ERRATA_801819
  89 config ARM_ERRATA_430973
  90         bool
  91
  92 config ARM_ERRATA_454179
  93         bool
  94
  95 config ARM_ERRATA_621766
  96         bool
  97
  98 config ARM_ERRATA_716044
  99         bool
 100
 101 config ARM_ERRATA_725233
 102         bool
 103
 104 config ARM_ERRATA_742230
 105         bool
 106
 107 config ARM_ERRATA_743622
 108         bool
 109
 110 config ARM_ERRATA_751472
 111         bool
 112
 113 config ARM_ERRATA_761320
 114         bool
 115
 116 config ARM_ERRATA_773022
 117         bool
 118
 119 config ARM_ERRATA_774769
 120         bool
 121
 122 config ARM_ERRATA_794072
 123         bool
 124
 125 config ARM_ERRATA_798870
 126         bool
 127
 128 config ARM_ERRATA_801819
 129         bool
 130
 131 config ARM_ERRATA_826974
 132         bool
 133
 134 config ARM_ERRATA_828024
 135         bool
 136
 137 config ARM_ERRATA_829520
 138         bool
 139
 140 config ARM_ERRATA_833069
 141         bool
 142
 143 config ARM_ERRATA_833471
 144         bool
 145
 146 config ARM_ERRATA_845369
 147        bool
 148
 149 config ARM_ERRATA_852421
 150         bool
 151
 152 config ARM_ERRATA_852423
 153         bool
 154
 155 config ARM_ERRATA_855873
 156         bool
 157
 158 config CPU_ARM720T
 159         bool
 160         select SYS_CACHE_SHIFT_5
 161
 162 config CPU_ARM920T
 163         bool
 164         select SYS_CACHE_SHIFT_5
 165
 166 config CPU_ARM926EJS
 167         bool
 168         select SYS_CACHE_SHIFT_5
 169
 170 config CPU_ARM946ES
 171         bool
 172         select SYS_CACHE_SHIFT_5
 173
 174 config CPU_ARM1136
 175         bool
 176         select SYS_CACHE_SHIFT_5
 177
 178 config CPU_ARM1176
 179         bool
 180         select HAS_VBAR
 181         select SYS_CACHE_SHIFT_5
 182
 183 config CPU_V7
 184         bool
 185         select HAS_VBAR
 186         select HAS_THUMB2
 187         select SYS_CACHE_SHIFT_6
 188
 189 config CPU_V7M
 190         bool
 191         select HAS_THUMB2
 192         select THUMB2_KERNEL
 193         select SYS_CACHE_SHIFT_5
 194
 195 config CPU_PXA
 196         bool
 197         select SYS_CACHE_SHIFT_5
 198
 199 config CPU_SA1100
 200         bool
 201         select SYS_CACHE_SHIFT_5
 202
 203 config SYS_CPU
 204         default "arm720t" if CPU_ARM720T
 205         default "arm920t" if CPU_ARM920T
 206         default "arm926ejs" if CPU_ARM926EJS
 207         default "arm946es" if CPU_ARM946ES
 208         default "arm1136" if CPU_ARM1136
 209         default "arm1176" if CPU_ARM1176
 210         default "armv7" if CPU_V7
 211         default "armv7m" if CPU_V7M
 212         default "pxa" if CPU_PXA
 213         default "sa1100" if CPU_SA1100
 214         default "armv8" if ARM64
 215
 216 config SYS_ARM_ARCH
 217         int
 218         default 4 if CPU_ARM720T
 219         default 4 if CPU_ARM920T
 220         default 5 if CPU_ARM926EJS
 221         default 5 if CPU_ARM946ES
 222         default 6 if CPU_ARM1136
 223         default 6 if CPU_ARM1176
 224         default 7 if CPU_V7
 225         default 7 if CPU_V7M
 226         default 5 if CPU_PXA
 227         default 4 if CPU_SA1100
 228         default 8 if ARM64
 229
 230 config SYS_CACHE_SHIFT_5
 231         bool
 232
 233 config SYS_CACHE_SHIFT_6
 234         bool
 235
 236 config SYS_CACHE_SHIFT_7
 237         bool
 238
 239 config SYS_CACHELINE_SIZE
 240         int
 241         default 128 if SYS_CACHE_SHIFT_7
 242         default 64 if SYS_CACHE_SHIFT_6
 243         default 32 if SYS_CACHE_SHIFT_5
 244
 245 config ARM_SMCCC
 246         bool "Support for ARM SMC Calling Convention (SMCCC)"
 247         depends on CPU_V7 || ARM64
 248         select ARM_PSCI_FW
 249         help
 250           Say Y here if you want to enable ARM SMC Calling Convention.
 251           This should be enabled if U-Boot needs to communicate with system
 252           firmware (for example, PSCI) according to SMCCC.
 253
 254 config SEMIHOSTING
 255         bool "support boot from semihosting"
 256         help
 257           In emulated environments, semihosting is a way for
 258           the hosted environment to call out to the emulator to
 259           retrieve files from the host machine.
 260
 261 config SYS_THUMB_BUILD
 262         bool "Build U-Boot using the Thumb instruction set"
 263         depends on !ARM64
 264         help
 265            Use this flag to build U-Boot using the Thumb instruction set for
 266            ARM architectures. Thumb instruction set provides better code
 267            density. For ARM architectures that support Thumb2 this flag will
 268            result in Thumb2 code generated by GCC.
 269
 270 config SPL_SYS_THUMB_BUILD
 271         bool "Build SPL using the Thumb instruction set"
 272         default y if SYS_THUMB_BUILD
 273         depends on !ARM64
 274         help
 275            Use this flag to build SPL using the Thumb instruction set for
 276            ARM architectures. Thumb instruction set provides better code
 277            density. For ARM architectures that support Thumb2 this flag will
 278            result in Thumb2 code generated by GCC.
 279
 280 config SYS_L2CACHE_OFF
 281         bool "L2cache off"
 282         help
 283           If SoC does not support L2CACHE or one do not want to enable
 284           L2CACHE, choose this option.
 285
 286 config ENABLE_ARM_SOC_BOOT0_HOOK
 287         bool "prepare BOOT0 header"
 288         help
 289           If the SoC's BOOT0 requires a header area filled with (magic)
 290           values, then choose this option, and create a define called
 291           ARM_SOC_BOOT0_HOOK which contains the required assembler
 292           preprocessor code.
 293
 294 config ARM_CORTEX_CPU_IS_UP
 295         bool
 296         default n
 297
 298 config USE_ARCH_MEMCPY
 299         bool "Use an assembly optimized implementation of memcpy"
 300         default y
 301         depends on !ARM64
 302         help
 303           Enable the generation of an optimized version of memcpy.
 304           Such implementation may be faster under some conditions
 305           but may increase the binary size.
 306
 307 config SPL_USE_ARCH_MEMCPY
 308         bool "Use an assembly optimized implementation of memcpy for SPL"
 309         default y if USE_ARCH_MEMCPY
 310         depends on !ARM64
 311         help
 312           Enable the generation of an optimized version of memcpy.
 313           Such implementation may be faster under some conditions
 314           but may increase the binary size.
 315
 316 config USE_ARCH_MEMSET
 317         bool "Use an assembly optimized implementation of memset"
 318         default y
 319         depends on !ARM64
 320         help
 321           Enable the generation of an optimized version of memset.
 322           Such implementation may be faster under some conditions
 323           but may increase the binary size.
 324
 325 config SPL_USE_ARCH_MEMSET
 326         bool "Use an assembly optimized implementation of memset for SPL"
 327         default y if USE_ARCH_MEMSET
 328         depends on !ARM64
 329         help
 330           Enable the generation of an optimized version of memset.
 331           Such implementation may be faster under some conditions
 332           but may increase the binary size.
 333
 334 config ARM64_SUPPORT_AARCH32
 335         bool "ARM64 system support AArch32 execution state"
 336         default y if ARM64 && !TARGET_THUNDERX_88XX
 337         help
 338           This ARM64 system supports AArch32 execution state.
 339
 340 choice
 341         prompt "Target select"
 342         default TARGET_HIKEY
 343
 344 config ARCH_AT91
 345         bool "Atmel AT91"
 346         select SPL_BOARD_INIT if SPL
 347
 348 config TARGET_EDB93XX
 349         bool "Support edb93xx"
 350         select CPU_ARM920T
 351
 352 config TARGET_ASPENITE
 353         bool "Support aspenite"
 354         select CPU_ARM926EJS
 355
 356 config TARGET_GPLUGD
 357         bool "Support gplugd"
 358         select CPU_ARM926EJS
 359
 360 config ARCH_DAVINCI
 361         bool "TI DaVinci"
 362         select CPU_ARM926EJS
 363         imply CMD_SAVES
 364         help
 365           Support for TI's DaVinci platform.
 366
 367 config KIRKWOOD
 368         bool "Marvell Kirkwood"
 369         select CPU_ARM926EJS
 370         select BOARD_EARLY_INIT_F
 371         select ARCH_MISC_INIT
 372
 373 config ARCH_MVEBU
 374         bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
 375         select OF_CONTROL
 376         select OF_SEPARATE
 377         select DM
 378         select DM_ETH
 379         select DM_SERIAL
 380         select DM_SPI
 381         select DM_SPI_FLASH
 382
 383 config TARGET_DEVKIT3250
 384         bool "Support devkit3250"
 385         select CPU_ARM926EJS
 386         select SUPPORT_SPL
 387
 388 config TARGET_WORK_92105
 389         bool "Support work_92105"
 390         select CPU_ARM926EJS
 391         select SUPPORT_SPL
 392
 393 config TARGET_APF27
 394         bool "Support apf27"
 395         select CPU_ARM926EJS
 396         select SUPPORT_SPL
 397
 398 config TARGET_APX4DEVKIT
 399         bool "Support apx4devkit"
 400         select CPU_ARM926EJS
 401         select SUPPORT_SPL
 402
 403 config TARGET_XFI3
 404         bool "Support xfi3"
 405         select CPU_ARM926EJS
 406         select SUPPORT_SPL
 407
 408 config TARGET_M28EVK
 409         bool "Support m28evk"
 410         select CPU_ARM926EJS
 411         select SUPPORT_SPL
 412
 413 config TARGET_MX23EVK
 414         bool "Support mx23evk"
 415         select CPU_ARM926EJS
 416         select SUPPORT_SPL
 417         select BOARD_EARLY_INIT_F
 418
 419 config TARGET_MX28EVK
 420         bool "Support mx28evk"
 421         select CPU_ARM926EJS
 422         select SUPPORT_SPL
 423         select BOARD_EARLY_INIT_F
 424
 425 config TARGET_MX23_OLINUXINO
 426         bool "Support mx23_olinuxino"
 427         select CPU_ARM926EJS
 428         select SUPPORT_SPL
 429         select BOARD_EARLY_INIT_F
 430
 431 config TARGET_BG0900
 432         bool "Support bg0900"
 433         select CPU_ARM926EJS
 434         select SUPPORT_SPL
 435
 436 config TARGET_SANSA_FUZE_PLUS
 437         bool "Support sansa_fuze_plus"
 438         select CPU_ARM926EJS
 439         select SUPPORT_SPL
 440
 441 config TARGET_SC_SPS_1
 442         bool "Support sc_sps_1"
 443         select CPU_ARM926EJS
 444         select SUPPORT_SPL
 445
 446 config ORION5X
 447         bool "Marvell Orion"
 448         select CPU_ARM926EJS
 449
 450 config TARGET_SPEAR300
 451         bool "Support spear300"
 452         select CPU_ARM926EJS
 453         select BOARD_EARLY_INIT_F
 454         imply CMD_SAVES
 455
 456 config TARGET_SPEAR310
 457         bool "Support spear310"
 458         select CPU_ARM926EJS
 459         select BOARD_EARLY_INIT_F
 460         imply CMD_SAVES
 461
 462 config TARGET_SPEAR320
 463         bool "Support spear320"
 464         select CPU_ARM926EJS
 465         select BOARD_EARLY_INIT_F
 466         imply CMD_SAVES
 467
 468 config TARGET_SPEAR600
 469         bool "Support spear600"
 470         select CPU_ARM926EJS
 471         select BOARD_EARLY_INIT_F
 472         imply CMD_SAVES
 473
 474 config TARGET_STV0991
 475         bool "Support stv0991"
 476         select CPU_V7
 477         select DM
 478         select DM_SERIAL
 479         select DM_SPI
 480         select DM_SPI_FLASH
 481         select SPI_FLASH
 482
 483 config TARGET_X600
 484         bool "Support x600"
 485         select BOARD_LATE_INIT
 486         select CPU_ARM926EJS
 487         select SUPPORT_SPL
 488
 489 config TARGET_IMX31_PHYCORE
 490         bool "Support imx31_phycore_eet"
 491         select CPU_ARM1136
 492         select BOARD_EARLY_INIT_F
 493
 494 config TARGET_IMX31_PHYCORE_EET
 495         bool "Support imx31_phycore_eet"
 496         select BOARD_LATE_INIT
 497         select CPU_ARM1136
 498         select BOARD_EARLY_INIT_F
 499
 500 config TARGET_MX31ADS
 501         bool "Support mx31ads"
 502         select CPU_ARM1136
 503         select BOARD_EARLY_INIT_F
 504
 505 config TARGET_MX31PDK
 506         bool "Support mx31pdk"
 507         select BOARD_LATE_INIT
 508         select CPU_ARM1136
 509         select SUPPORT_SPL
 510         select BOARD_EARLY_INIT_F
 511
 512 config TARGET_WOODBURN
 513         bool "Support woodburn"
 514         select CPU_ARM1136
 515
 516 config TARGET_WOODBURN_SD
 517         bool "Support woodburn_sd"
 518         select CPU_ARM1136
 519         select SUPPORT_SPL
 520
 521 config TARGET_FLEA3
 522         bool "Support flea3"
 523         select CPU_ARM1136
 524
 525 config TARGET_MX35PDK
 526         bool "Support mx35pdk"
 527         select BOARD_LATE_INIT
 528         select CPU_ARM1136
 529
 530 config ARCH_BCM283X
 531         bool "Broadcom BCM283X family"
 532         select DM
 533         select DM_SERIAL
 534         select DM_GPIO
 535         select OF_CONTROL
 536         imply FAT_WRITE
 537
 538 config TARGET_VEXPRESS_CA15_TC2
 539         bool "Support vexpress_ca15_tc2"
 540         select CPU_V7
 541         select CPU_V7_HAS_NONSEC
 542         select CPU_V7_HAS_VIRT
 543
 544 config TARGET_VEXPRESS_CA5X2
 545         bool "Support vexpress_ca5x2"
 546         select CPU_V7
 547
 548 config TARGET_VEXPRESS_CA9X4
 549         bool "Support vexpress_ca9x4"
 550         select CPU_V7
 551
 552 config TARGET_BCM23550_W1D
 553         bool "Support bcm23550_w1d"
 554         select CPU_V7
 555         imply CRC32_VERIFY
 556         imply FAT_WRITE
 557
 558 config TARGET_BCM28155_AP
 559         bool "Support bcm28155_ap"
 560         select CPU_V7
 561         imply CRC32_VERIFY
 562         imply FAT_WRITE
 563
 564 config TARGET_BCMCYGNUS
 565         bool "Support bcmcygnus"
 566         select CPU_V7
 567         imply CRC32_VERIFY
 568         imply CMD_HASH
 569         imply FAT_WRITE
 570         imply HASH_VERIFY
 571         imply NETDEVICES
 572         imply BCM_SF2_ETH
 573         imply BCM_SF2_ETH_GMAC
 574
 575 config TARGET_BCMNSP
 576         bool "Support bcmnsp"
 577         select CPU_V7
 578
 579 config TARGET_BCMNS2
 580         bool "Support Broadcom Northstar2"
 581         select ARM64
 582         help
 583           Support for Broadcom Northstar 2 SoCs.  NS2 is a quad-core 64-bit
 584           ARMv8 Cortex-A57 processors targeting a broad range of networking
 585           applications
 586
 587 config ARCH_EXYNOS
 588         bool "Samsung EXYNOS"
 589         select DM
 590         select DM_I2C
 591         select DM_SPI_FLASH
 592         select DM_SERIAL
 593         select DM_SPI
 594         select DM_GPIO
 595         select DM_KEYBOARD
 596         imply FAT_WRITE
 597
 598 config ARCH_S5PC1XX
 599         bool "Samsung S5PC1XX"
 600         select CPU_V7
 601         select DM
 602         select DM_SERIAL
 603         select DM_GPIO
 604         select DM_I2C
 605
 606 config ARCH_HIGHBANK
 607         bool "Calxeda Highbank"
 608         select CPU_V7
 609
 610 config ARCH_INTEGRATOR
 611         bool "ARM Ltd. Integrator family"
 612         select DM
 613         select DM_SERIAL
 614
 615 config ARCH_KEYSTONE
 616         bool "TI Keystone"
 617         select CPU_V7
 618         select SUPPORT_SPL
 619         select SYS_THUMB_BUILD
 620         select CMD_POWEROFF
 621         imply CMD_MTDPARTS
 622         imply FIT
 623         imply CMD_SAVES
 624
 625 config ARCH_OMAP2PLUS
 626         bool "TI OMAP2+"
 627         select CPU_V7
 628         select SPL_BOARD_INIT if SPL
 629         select SPL_STACK_R if SPL
 630         select SUPPORT_SPL
 631         imply FIT
 632
 633 config ARCH_MESON
 634         bool "Amlogic Meson"
 635         help
 636           Support for the Meson SoC family developed by Amlogic Inc.,
 637           targeted at media players and tablet computers. We currently
 638           support the S905 (GXBaby) 64-bit SoC.
 639
 640 config ARCH_MX25
 641         bool "NXP MX25"
 642         select CPU_ARM926EJS
 643
 644 config ARCH_MX7ULP
 645         bool "NXP MX7ULP"
 646         select CPU_V7
 647         select ROM_UNIFIED_SECTIONS
 648
 649 config ARCH_MX7
 650         bool "Freescale MX7"
 651         select CPU_V7
 652         select SYS_FSL_HAS_SEC if SECURE_BOOT
 653         select SYS_FSL_SEC_COMPAT_4
 654         select SYS_FSL_SEC_LE
 655         select BOARD_EARLY_INIT_F
 656         select ARCH_MISC_INIT
 657
 658 config ARCH_MX6
 659         bool "Freescale MX6"
 660         select CPU_V7
 661         select SYS_FSL_HAS_SEC if SECURE_BOOT
 662         select SYS_FSL_SEC_COMPAT_4
 663         select SYS_FSL_SEC_LE
 664         select SYS_THUMB_BUILD if SPL
 665
 666 if ARCH_MX6
 667 config SPL_LDSCRIPT
 668         default "arch/arm/mach-omap2/u-boot-spl.lds"
 669 endif
 670
 671 config ARCH_MX5
 672         bool "Freescale MX5"
 673         select CPU_V7
 674         select BOARD_EARLY_INIT_F
 675
 676 config ARCH_QEMU
 677         bool "QEMU Virtual Platform"
 678         select CPU_V7
 679         select ARCH_SUPPORT_PSCI
 680         select DM
 681         select DM_SERIAL
 682         select OF_CONTROL
 683
 684 config ARCH_RMOBILE
 685         bool "Renesas ARM SoCs"
 686         select DM
 687         select DM_SERIAL
 688         select BOARD_EARLY_INIT_F
 689         imply FAT_WRITE
 690         imply SYS_THUMB_BUILD
 691
 692 config TARGET_S32V234EVB
 693         bool "Support s32v234evb"
 694         select ARM64
 695         select SYS_FSL_ERRATUM_ESDHC111
 696
 697 config ARCH_SNAPDRAGON
 698         bool "Qualcomm Snapdragon SoCs"
 699         select ARM64
 700         select DM
 701         select DM_GPIO
 702         select DM_SERIAL
 703         select SPMI
 704         select OF_CONTROL
 705         select OF_SEPARATE
 706
 707 config ARCH_SOCFPGA
 708         bool "Altera SOCFPGA family"
 709         select CPU_V7
 710         select SUPPORT_SPL
 711         select OF_CONTROL
 712         select SPL_OF_CONTROL
 713         select DM
 714         select DM_SPI_FLASH
 715         select DM_SPI
 716         select ENABLE_ARM_SOC_BOOT0_HOOK
 717         select ARCH_EARLY_INIT_R
 718         select ARCH_MISC_INIT
 719         select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
 720         select SYS_THUMB_BUILD
 721         imply CMD_MTDPARTS
 722         imply CRC32_VERIFY
 723         imply FAT_WRITE
 724
 725 config ARCH_SUNXI
 726         bool "Support sunxi (Allwinner) SoCs"
 727         select BINMAN
 728         select CMD_GPIO
 729         select CMD_MMC if MMC
 730         select CMD_USB if DISTRO_DEFAULTS
 731         select DM
 732         select DM_ETH
 733         select DM_GPIO
 734         select DM_KEYBOARD
 735         select DM_SERIAL
 736         select DM_USB if DISTRO_DEFAULTS
 737         select OF_BOARD_SETUP
 738         select OF_CONTROL
 739         select OF_SEPARATE
 740         select SPL_STACK_R if SPL
 741         select SPL_SYS_MALLOC_SIMPLE if SPL
 742         select SYS_NS16550
 743         select SPL_SYS_THUMB_BUILD if !ARM64
 744         select SYS_THUMB_BUILD if !ARM64
 745         select USB if DISTRO_DEFAULTS
 746         select USB_STORAGE if DISTRO_DEFAULTS
 747         select USB_KEYBOARD if DISTRO_DEFAULTS
 748         select USE_TINY_PRINTF
 749         imply CMD_GPT
 750         imply FAT_WRITE
 751         imply PRE_CONSOLE_BUFFER
 752         imply SPL_GPIO_SUPPORT
 753         imply SPL_LIBCOMMON_SUPPORT
 754         imply SPL_LIBDISK_SUPPORT
 755         imply SPL_LIBGENERIC_SUPPORT
 756         imply SPL_MMC_SUPPORT if MMC
 757         imply SPL_POWER_SUPPORT
 758         imply SPL_SERIAL_SUPPORT
 759         imply USB_GADGET
 760
 761 config TARGET_TS4600
 762         bool "Support TS4600"
 763         select CPU_ARM926EJS
 764         select SUPPORT_SPL
 765
 766 config ARCH_VF610
 767         bool "Freescale Vybrid"
 768         select CPU_V7
 769         select SYS_FSL_ERRATUM_ESDHC111
 770         imply CMD_MTDPARTS
 771         imply NAND
 772
 773 config ARCH_ZYNQ
 774         bool "Xilinx Zynq based platform"
 775         select BOARD_LATE_INIT
 776         select CPU_V7
 777         select SUPPORT_SPL
 778         select OF_CONTROL
 779         select SPL_BOARD_INIT if SPL
 780         select SPL_OF_CONTROL if SPL
 781         select DM
 782         select DM_ETH
 783         select DM_GPIO
 784         select SPL_DM if SPL
 785         select DM_MMC
 786         select DM_SPI
 787         select DM_SERIAL
 788         select DM_SPI_FLASH
 789         select SPL_SEPARATE_BSS if SPL
 790         select DM_USB if USB
 791         select BLK
 792         select CLK
 793         select SPL_CLK
 794         select CLK_ZYNQ
 795         imply CMD_CLK
 796         imply FAT_WRITE
 797         imply CMD_SPL
 798
 799 config ARCH_ZYNQMP
 800         bool "Xilinx ZynqMP based platform"
 801         select ARM64
 802         select BOARD_LATE_INIT
 803         select DM
 804         select OF_CONTROL
 805         select DM_SERIAL
 806         select SUPPORT_SPL
 807         select CLK
 808         select SPL_BOARD_INIT if SPL
 809         select SPL_CLK if SPL
 810         select DM_USB if USB
 811         imply FAT_WRITE
 812
 813 config TEGRA
 814         bool "NVIDIA Tegra"
 815         imply FAT_WRITE
 816
 817 config TARGET_VEXPRESS64_AEMV8A
 818         bool "Support vexpress_aemv8a"
 819         select ARM64
 820
 821 config TARGET_VEXPRESS64_BASE_FVP
 822         bool "Support Versatile Express ARMv8a FVP BASE model"
 823         select ARM64
 824         select SEMIHOSTING
 825
 826 config TARGET_VEXPRESS64_BASE_FVP_DRAM
 827         bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM"
 828         select ARM64
 829         help
 830           This target is derived from TARGET_VEXPRESS64_BASE_FVP and over-rides
 831           the default config to allow the user to load the images directly into
 832           DRAM using model parameters rather than by using semi-hosting to load
 833           the files from the host filesystem.
 834
 835 config TARGET_VEXPRESS64_JUNO
 836         bool "Support Versatile Express Juno Development Platform"
 837         select ARM64
 838
 839 config TARGET_LS2080A_EMU
 840         bool "Support ls2080a_emu"
 841         select ARCH_LS2080A
 842         select ARM64
 843         select ARMV8_MULTIENTRY
 844         select ARCH_MISC_INIT
 845         help
 846           Support for Freescale LS2080A_EMU platform
 847           The LS2080A Development System (EMULATOR) is a pre silicon
 848           development platform that supports the QorIQ LS2080A
 849           Layerscape Architecture processor.
 850
 851 config TARGET_LS2080A_SIMU
 852         bool "Support ls2080a_simu"
 853         select ARCH_LS2080A
 854         select ARM64
 855         select ARMV8_MULTIENTRY
 856         select ARCH_MISC_INIT
 857         help
 858           Support for Freescale LS2080A_SIMU platform
 859           The LS2080A Development System (QDS) is a pre silicon
 860           development platform that supports the QorIQ LS2080A
 861           Layerscape Architecture processor.
 862
 863 config TARGET_LS1088AQDS
 864         bool "Support ls1088aqds"
 865         select ARCH_LS1088A
 866         select ARM64
 867         select ARMV8_MULTIENTRY
 868         select ARCH_MISC_INIT
 869         select BOARD_LATE_INIT
 870         select SUPPORT_SPL
 871         help
 872           Support for NXP LS1088AQDS platform
 873           The LS1088A Development System (QDS) is a high-performance
 874           development platform that supports the QorIQ LS1088A
 875           Layerscape Architecture processor.
 876
 877 config TARGET_LS2080AQDS
 878         bool "Support ls2080aqds"
 879         select ARCH_LS2080A
 880         select ARM64
 881         select ARMV8_MULTIENTRY
 882         select BOARD_LATE_INIT
 883         select SUPPORT_SPL
 884         select ARCH_MISC_INIT
 885         imply SCSI
 886         imply SCSI_AHCI
 887         help
 888           Support for Freescale LS2080AQDS platform
 889           The LS2080A Development System (QDS) is a high-performance
 890           development platform that supports the QorIQ LS2080A
 891           Layerscape Architecture processor.
 892
 893 config TARGET_LS2080ARDB
 894         bool "Support ls2080ardb"
 895         select ARCH_LS2080A
 896         select ARM64
 897         select ARMV8_MULTIENTRY
 898         select BOARD_LATE_INIT
 899         select SUPPORT_SPL
 900         select ARCH_MISC_INIT
 901         imply SCSI
 902         imply SCSI_AHCI
 903         help
 904           Support for Freescale LS2080ARDB platform.
 905           The LS2080A Reference design board (RDB) is a high-performance
 906           development platform that supports the QorIQ LS2080A
 907           Layerscape Architecture processor.
 908
 909 config TARGET_LS2081ARDB
 910         bool "Support ls2081ardb"
 911         select ARCH_LS2080A
 912         select ARM64
 913         select ARMV8_MULTIENTRY
 914         select BOARD_LATE_INIT
 915         select SUPPORT_SPL
 916         select ARCH_MISC_INIT
 917         help
 918           Support for Freescale LS2081ARDB platform.
 919           The LS2081A Reference design board (RDB) is a high-performance
 920           development platform that supports the QorIQ LS2081A/LS2041A
 921           Layerscape Architecture processor.
 922
 923 config TARGET_HIKEY
 924         bool "Support HiKey 96boards Consumer Edition Platform"
 925         select ARM64
 926         select DM
 927         select DM_GPIO
 928         select DM_SERIAL
 929         select OF_CONTROL
 930           help
 931           Support for HiKey 96boards platform. It features a HI6220
 932           SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
 933
 934 config TARGET_POPLAR
 935         bool "Support Poplar 96boards Enterprise Edition Platform"
 936         select ARM64
 937         select DM
 938         select OF_CONTROL
 939         select DM_SERIAL
 940         select DM_USB
 941           help
 942           Support for Poplar 96boards EE platform. It features a HI3798cv200
 943           SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
 944           making it capable of running any commercial set-top solution based on
 945           Linux or Android.
 946
 947 config TARGET_LS1012AQDS
 948         bool "Support ls1012aqds"
 949         select ARCH_LS1012A
 950         select ARM64
 951         select BOARD_LATE_INIT
 952         help
 953           Support for Freescale LS1012AQDS platform.
 954           The LS1012A Development System (QDS) is a high-performance
 955           development platform that supports the QorIQ LS1012A
 956           Layerscape Architecture processor.
 957
 958 config TARGET_LS1012ARDB
 959         bool "Support ls1012ardb"
 960         select ARCH_LS1012A
 961         select ARM64
 962         select BOARD_LATE_INIT
 963         imply SCSI
 964         imply SCSI_AHCI
 965         help
 966           Support for Freescale LS1012ARDB platform.
 967           The LS1012A Reference design board (RDB) is a high-performance
 968           development platform that supports the QorIQ LS1012A
 969           Layerscape Architecture processor.
 970
 971 config TARGET_LS1012AFRDM
 972         bool "Support ls1012afrdm"
 973         select ARCH_LS1012A
 974         select ARM64
 975         help
 976           Support for Freescale LS1012AFRDM platform.
 977           The LS1012A Freedom  board (FRDM) is a high-performance
 978           development platform that supports the QorIQ LS1012A
 979           Layerscape Architecture processor.
 980
 981 config TARGET_LS1088ARDB
 982         bool "Support ls1088ardb"
 983         select ARCH_LS1088A
 984         select ARM64
 985         select ARMV8_MULTIENTRY
 986         select ARCH_MISC_INIT
 987         select BOARD_LATE_INIT
 988         select SUPPORT_SPL
 989         help
 990           Support for NXP LS1088ARDB platform.
 991           The LS1088A Reference design board (RDB) is a high-performance
 992           development platform that supports the QorIQ LS1088A
 993           Layerscape Architecture processor.
 994
 995 config TARGET_LS1021AQDS
 996         bool "Support ls1021aqds"
 997         select BOARD_LATE_INIT
 998         select CPU_V7
 999         select CPU_V7_HAS_NONSEC
1000         select CPU_V7_HAS_VIRT
1001         select SUPPORT_SPL
1002         select ARCH_LS1021A
1003         select ARCH_SUPPORT_PSCI
1004         select LS1_DEEP_SLEEP
1005         select SYS_FSL_DDR
1006         select BOARD_EARLY_INIT_F
1007         imply SCSI
1008
1009 config TARGET_LS1021ATWR
1010         bool "Support ls1021atwr"
1011         select BOARD_LATE_INIT
1012         select CPU_V7
1013         select CPU_V7_HAS_NONSEC
1014         select CPU_V7_HAS_VIRT
1015         select SUPPORT_SPL
1016         select ARCH_LS1021A
1017         select ARCH_SUPPORT_PSCI
1018         select LS1_DEEP_SLEEP
1019         select BOARD_EARLY_INIT_F
1020         imply SCSI
1021
1022 config TARGET_LS1021AIOT
1023         bool "Support ls1021aiot"
1024         select BOARD_LATE_INIT
1025         select CPU_V7
1026         select CPU_V7_HAS_NONSEC
1027         select CPU_V7_HAS_VIRT
1028         select SUPPORT_SPL
1029         select ARCH_LS1021A
1030         select ARCH_SUPPORT_PSCI
1031         imply SCSI
1032         help
1033           Support for Freescale LS1021AIOT platform.
1034           The LS1021A Freescale board (IOT) is a high-performance
1035           development platform that supports the QorIQ LS1021A
1036           Layerscape Architecture processor.
1037
1038 config TARGET_LS1043AQDS
1039         bool "Support ls1043aqds"
1040         select ARCH_LS1043A
1041         select ARM64
1042         select ARMV8_MULTIENTRY
1043         select BOARD_LATE_INIT
1044         select SUPPORT_SPL
1045         select BOARD_EARLY_INIT_F
1046         imply SCSI
1047         help
1048           Support for Freescale LS1043AQDS platform.
1049
1050 config TARGET_LS1043ARDB
1051         bool "Support ls1043ardb"
1052         select ARCH_LS1043A
1053         select ARM64
1054         select ARMV8_MULTIENTRY
1055         select BOARD_LATE_INIT
1056         select SUPPORT_SPL
1057         select BOARD_EARLY_INIT_F
1058         imply SCSI
1059         help
1060           Support for Freescale LS1043ARDB platform.
1061
1062 config TARGET_LS1046AQDS
1063         bool "Support ls1046aqds"
1064         select ARCH_LS1046A
1065         select ARM64
1066         select ARMV8_MULTIENTRY
1067         select BOARD_LATE_INIT
1068         select SUPPORT_SPL
1069         select DM_SPI_FLASH if DM_SPI
1070         select BOARD_EARLY_INIT_F
1071         imply SCSI
1072         help
1073           Support for Freescale LS1046AQDS platform.
1074           The LS1046A Development System (QDS) is a high-performance
1075           development platform that supports the QorIQ LS1046A
1076           Layerscape Architecture processor.
1077
1078 config TARGET_LS1046ARDB
1079         bool "Support ls1046ardb"
1080         select ARCH_LS1046A
1081         select ARM64
1082         select ARMV8_MULTIENTRY
1083         select BOARD_LATE_INIT
1084         select SUPPORT_SPL
1085         select DM_SPI_FLASH if DM_SPI
1086         select POWER_MC34VR500
1087         select BOARD_EARLY_INIT_F
1088         imply SCSI
1089         help
1090           Support for Freescale LS1046ARDB platform.
1091           The LS1046A Reference Design Board (RDB) is a high-performance
1092           development platform that supports the QorIQ LS1046A
1093           Layerscape Architecture processor.
1094
1095 config TARGET_H2200
1096         bool "Support h2200"
1097         select CPU_PXA
1098
1099 config TARGET_ZIPITZ2
1100         bool "Support zipitz2"
1101         select CPU_PXA
1102
1103 config TARGET_COLIBRI_PXA270
1104         bool "Support colibri_pxa270"
1105         select CPU_PXA
1106
1107 config ARCH_UNIPHIER
1108         bool "Socionext UniPhier SoCs"
1109         select BOARD_LATE_INIT
1110         select DM
1111         select DM_GPIO
1112         select DM_I2C
1113         select DM_MMC
1114         select DM_RESET
1115         select DM_SERIAL
1116         select DM_USB
1117         select OF_CONTROL
1118         select OF_LIBFDT
1119         select PINCTRL
1120         select SPL_BOARD_INIT if SPL
1121         select SPL_DM if SPL
1122         select SPL_LIBCOMMON_SUPPORT if SPL
1123         select SPL_LIBGENERIC_SUPPORT if SPL
1124         select SPL_OF_CONTROL if SPL
1125         select SPL_PINCTRL if SPL
1126         select SUPPORT_SPL
1127         imply FAT_WRITE
1128         help
1129           Support for UniPhier SoC family developed by Socionext Inc.
1130           (formerly, System LSI Business Division of Panasonic Corporation)
1131
1132 config STM32
1133         bool "Support STM32"
1134         select CPU_V7M
1135         select DM
1136         select DM_SERIAL
1137         select SYS_THUMB_BUILD
1138
1139 config ARCH_STI
1140         bool "Support STMicrolectronics SoCs"
1141         select CPU_V7
1142         select DM
1143         select DM_SERIAL
1144         select BLK
1145         select DM_MMC
1146         select DM_RESET
1147         help
1148           Support for STMicroelectronics STiH407/10 SoC family.
1149           This SoC is used on Linaro 96Board STiH410-B2260
1150
1151 config ARCH_ROCKCHIP
1152         bool "Support Rockchip SoCs"
1153         select OF_CONTROL
1154         select BLK
1155         select DM
1156         select SPL_DM if SPL
1157         select SYS_MALLOC_F
1158         select SYS_THUMB_BUILD if !ARM64
1159         select SPL_SYS_MALLOC_SIMPLE if SPL
1160         select DM_GPIO
1161         select DM_I2C
1162         select DM_MMC
1163         select DM_SERIAL
1164         select DM_SPI
1165         select DM_SPI_FLASH
1166         select DM_USB if USB
1167         select DM_PWM
1168         select DM_REGULATOR
1169         select ENABLE_ARM_SOC_BOOT0_HOOK
1170         imply CMD_FASTBOOT
1171         imply FASTBOOT
1172         imply FAT_WRITE
1173         imply USB_FUNCTION_FASTBOOT
1174         imply SPL_SYSRESET
1175         imply TPL_SYSRESET
1176         imply ADC
1177         imply SARADC_ROCKCHIP
1178
1179 config TARGET_THUNDERX_88XX
1180         bool "Support ThunderX 88xx"
1181         select ARM64
1182         select OF_CONTROL
1183         select SYS_CACHE_SHIFT_7
1184
1185 config ARCH_ASPEED
1186         bool "Support Aspeed SoCs"
1187         select OF_CONTROL
1188         select DM
1189
1190 endchoice
1191
1192 source "arch/arm/mach-aspeed/Kconfig"
1193
1194 source "arch/arm/mach-at91/Kconfig"
1195
1196 source "arch/arm/mach-bcm283x/Kconfig"
1197
1198 source "arch/arm/mach-davinci/Kconfig"
1199
1200 source "arch/arm/mach-exynos/Kconfig"
1201
1202 source "arch/arm/mach-highbank/Kconfig"
1203
1204 source "arch/arm/mach-integrator/Kconfig"
1205
1206 source "arch/arm/mach-keystone/Kconfig"
1207
1208 source "arch/arm/mach-kirkwood/Kconfig"
1209
1210 source "arch/arm/mach-mvebu/Kconfig"
1211
1212 source "arch/arm/cpu/armv7/ls102xa/Kconfig"
1213
1214 source "arch/arm/mach-imx/mx2/Kconfig"
1215
1216 source "arch/arm/mach-imx/mx7ulp/Kconfig"
1217
1218 source "arch/arm/mach-imx/mx7/Kconfig"
1219
1220 source "arch/arm/mach-imx/mx6/Kconfig"
1221
1222 source "arch/arm/mach-imx/mx5/Kconfig"
1223
1224 source "arch/arm/mach-omap2/Kconfig"
1225
1226 source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
1227
1228 source "arch/arm/mach-orion5x/Kconfig"
1229
1230 source "arch/arm/mach-rmobile/Kconfig"
1231
1232 source "arch/arm/mach-meson/Kconfig"
1233
1234 source "arch/arm/mach-qemu/Kconfig"
1235
1236 source "arch/arm/mach-rockchip/Kconfig"
1237
1238 source "arch/arm/mach-s5pc1xx/Kconfig"
1239
1240 source "arch/arm/mach-snapdragon/Kconfig"
1241
1242 source "arch/arm/mach-socfpga/Kconfig"
1243
1244 source "arch/arm/mach-sti/Kconfig"
1245
1246 source "arch/arm/mach-stm32/Kconfig"
1247
1248 source "arch/arm/mach-sunxi/Kconfig"
1249
1250 source "arch/arm/mach-tegra/Kconfig"
1251
1252 source "arch/arm/mach-uniphier/Kconfig"
1253
1254 source "arch/arm/cpu/armv7/vf610/Kconfig"
1255
1256 source "arch/arm/mach-zynq/Kconfig"
1257
1258 source "arch/arm/cpu/armv7/Kconfig"
1259
1260 source "arch/arm/cpu/armv8/zynqmp/Kconfig"
1261
1262 source "arch/arm/cpu/armv8/Kconfig"
1263
1264 source "arch/arm/mach-imx/Kconfig"
1265
1266 source "board/aries/m28evk/Kconfig"
1267 source "board/bosch/shc/Kconfig"
1268 source "board/CarMediaLab/flea3/Kconfig"
1269 source "board/Marvell/aspenite/Kconfig"
1270 source "board/Marvell/gplugd/Kconfig"
1271 source "board/armadeus/apf27/Kconfig"
1272 source "board/armltd/vexpress/Kconfig"
1273 source "board/armltd/vexpress64/Kconfig"
1274 source "board/bluegiga/apx4devkit/Kconfig"
1275 source "board/broadcom/bcm23550_w1d/Kconfig"
1276 source "board/broadcom/bcm28155_ap/Kconfig"
1277 source "board/broadcom/bcmcygnus/Kconfig"
1278 source "board/broadcom/bcmnsp/Kconfig"
1279 source "board/broadcom/bcmns2/Kconfig"
1280 source "board/cavium/thunderx/Kconfig"
1281 source "board/cirrus/edb93xx/Kconfig"
1282 source "board/creative/xfi3/Kconfig"
1283 source "board/freescale/ls2080a/Kconfig"
1284 source "board/freescale/ls2080aqds/Kconfig"
1285 source "board/freescale/ls2080ardb/Kconfig"
1286 source "board/freescale/ls1088a/Kconfig"
1287 source "board/freescale/ls1021aqds/Kconfig"
1288 source "board/freescale/ls1043aqds/Kconfig"
1289 source "board/freescale/ls1021atwr/Kconfig"
1290 source "board/freescale/ls1021aiot/Kconfig"
1291 source "board/freescale/ls1046aqds/Kconfig"
1292 source "board/freescale/ls1043ardb/Kconfig"
1293 source "board/freescale/ls1046ardb/Kconfig"
1294 source "board/freescale/ls1012aqds/Kconfig"
1295 source "board/freescale/ls1012ardb/Kconfig"
1296 source "board/freescale/ls1012afrdm/Kconfig"
1297 source "board/freescale/mx23evk/Kconfig"
1298 source "board/freescale/mx28evk/Kconfig"
1299 source "board/freescale/mx31ads/Kconfig"
1300 source "board/freescale/mx31pdk/Kconfig"
1301 source "board/freescale/mx35pdk/Kconfig"
1302 source "board/freescale/s32v234evb/Kconfig"
1303 source "board/gdsys/a38x/Kconfig"
1304 source "board/grinn/chiliboard/Kconfig"
1305 source "board/gumstix/pepper/Kconfig"
1306 source "board/h2200/Kconfig"
1307 source "board/hisilicon/hikey/Kconfig"
1308 source "board/hisilicon/poplar/Kconfig"
1309 source "board/imx31_phycore/Kconfig"
1310 source "board/isee/igep003x/Kconfig"
1311 source "board/olimex/mx23_olinuxino/Kconfig"
1312 source "board/phytec/pcm051/Kconfig"
1313 source "board/ppcag/bg0900/Kconfig"
1314 source "board/sandisk/sansa_fuze_plus/Kconfig"
1315 source "board/schulercontrol/sc_sps_1/Kconfig"
1316 source "board/silica/pengwyn/Kconfig"
1317 source "board/spear/spear300/Kconfig"
1318 source "board/spear/spear310/Kconfig"
1319 source "board/spear/spear320/Kconfig"
1320 source "board/spear/spear600/Kconfig"
1321 source "board/spear/x600/Kconfig"
1322 source "board/st/stv0991/Kconfig"
1323 source "board/tcl/sl50/Kconfig"
1324 source "board/birdland/bav335x/Kconfig"
1325 source "board/timll/devkit3250/Kconfig"
1326 source "board/toradex/colibri_pxa270/Kconfig"
1327 source "board/technologic/ts4600/Kconfig"
1328 source "board/vscom/baltos/Kconfig"
1329 source "board/woodburn/Kconfig"
1330 source "board/work-microwave/work_92105/Kconfig"
1331 source "board/zipitz2/Kconfig"
1332
1333 source "arch/arm/Kconfig.debug"
1334
1335 endmenu
1336
1337 config SPL_LDSCRIPT
1338         default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if TARGET_APX4DEVKIT || TARGET_BG0900 || TARGET_M28EVK || TARGET_MX23_OLINUXINO || TARGET_MX23EVK || TARGET_MX28EVK || TARGET_SANSA_FUZE_PLUS || TARGET_SC_SPS_1 || TARGET_TS4600 || TARGET_XFI3
1339         default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
1340         default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
1341
1342