arch/arm/cpu/armv8/zynqmp/Kconfig

   1 if ARCH_ZYNQMP
   2
   3 config SPL_FAT_SUPPORT
   4         default y
   5
   6 config SPL_LIBCOMMON_SUPPORT
   7         default y
   8
   9 config SPL_LIBDISK_SUPPORT
  10         default y
  11
  12 config SPL_LIBGENERIC_SUPPORT
  13         default y
  14
  15 config SPL_MMC_SUPPORT
  16         default y if MMC_SDHCI_ZYNQ
  17
  18 config SPL_SERIAL_SUPPORT
  19         default y
  20
  21 config SPL_SPI_FLASH_SUPPORT
  22         default y if ZYNQ_QSPI
  23
  24 config SPL_SPI_SUPPORT
  25         default y if ZYNQ_QSPI
  26
  27 config SYS_BOARD
  28         default "zynqmp"
  29
  30 config SYS_VENDOR
  31         string "Vendor name"
  32         default "xilinx"
  33
  34 config SYS_SOC
  35         default "zynqmp"
  36
  37 config SYS_CONFIG_NAME
  38         string "Board configuration name"
  39         default "xilinx_zynqmp"
  40         help
  41           This option contains information about board configuration name.
  42           Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header
  43           will be used for board configuration.
  44
  45 config SYS_MEM_RSVD_FOR_MMU
  46         bool "Reserve memory for MMU Table"
  47         help
  48           If defined this option is used to setup different space for
  49           MMU table than the one which will be allocated during
  50           relocation.
  51
  52 config BOOT_INIT_FILE
  53         string "boot.bin init register filename"
  54         depends on SPL
  55         default ""
  56         help
  57           Add register writes to boot.bin format (max 256 pairs).
  58           Expect a table of register-value pairs, e.g. "0x12345678 0x4321"
  59
  60 config ZYNQMP_USB
  61         bool "Configure ZynqMP USB"
  62
  63 config SYS_MALLOC_F_LEN
  64         default 0x600
  65
  66 config DEFINE_TCM_OCM_MMAP
  67         bool "Define TCM and OCM memory in MMU Table"
  68         help
  69           This option if enabled defines the TCM and OCM memory and its
  70           memory attributes in MMU table entry.
  71
  72 config ZYNQMP_PSU_INIT_ENABLED
  73         bool "Include psu_init"
  74         help
  75           Include psu_init to full u-boot. SPL include psu_init by default.
  76
  77 config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
  78         bool "Overwrite SPL bootmode"
  79         depends on SPL
  80         help
  81           Overwrite bootmode selected via boot mode pins to tell SPL what should
  82           be the next boot device.
  83
  84 config SPL_ZYNQMP_ALT_BOOTMODE
  85         hex
  86         default 0x0 if JTAG_MODE
  87         default 0x1 if QSPI_MODE_24BIT
  88         default 0x2 if QSPI_MODE_32BIT
  89         default 0x3 if SD_MODE
  90         default 0x4 if NAND_MODE
  91         default 0x5 if SD_MODE1
  92         default 0x6 if EMMC_MODE
  93         default 0x7 if USB_MODE
  94         default 0xa if SW_USBHOST_MODE
  95         default 0xb if SW_SATA_MODE
  96
  97 choice
  98         prompt "Boot mode"
  99         depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
 100         default JTAG
 101
 102 config JTAG_MODE
 103         bool "JTAG_MODE"
 104
 105 config QSPI_MODE_24BIT
 106         bool "QSPI_MODE_24BIT"
 107
 108 config QSPI_MODE_32BIT
 109         bool "QSPI_MODE_32BIT"
 110
 111 config SD_MODE
 112         bool "SD_MODE"
 113
 114 config SD_MODE1
 115         bool "SD_MODE1"
 116
 117 config NAND_MODE
 118         bool "NAND_MODE"
 119
 120 config EMMC_MODE
 121         bool "EMMC_MODE"
 122
 123 config USB_MODE
 124         bool "USB"
 125
 126 config SW_USBHOST_MODE
 127         bool "SW USBHOST_MODE"
 128
 129 config SW_SATA_MODE
 130         bool "SW SATA_MODE"
 131
 132 endchoice
 133
 134 endif