arch/arm/mach-uniphier/Kconfig

   1 if ARCH_UNIPHIER
   2
   3 config SYS_CONFIG_NAME
   4         default "uniphier"
   5
   6 config ARCH_UNIPHIER_32BIT
   7         bool
   8         select CPU_V7
   9         select CPU_V7_HAS_NONSEC
  10         select ARMV7_NONSEC
  11         select ARCH_SUPPORT_PSCI
  12
  13 config ARCH_UNIPHIER_64BIT
  14         bool
  15         select ARM64
  16         select SPL_SEPARATE_BSS if SPL
  17         select ARMV8_MULTIENTRY if SPL
  18         select ARMV8_SPIN_TABLE if SPL
  19
  20 choice
  21         prompt "UniPhier SoC select"
  22         default ARCH_UNIPHIER_PRO4
  23
  24 config ARCH_UNIPHIER_SLD3
  25         bool "UniPhier sLD3 SoC"
  26         select ARCH_UNIPHIER_32BIT
  27
  28 config ARCH_UNIPHIER_LD4_SLD8
  29         bool "UniPhier LD4/sLD8 SoCs"
  30         select ARCH_UNIPHIER_32BIT
  31
  32 config ARCH_UNIPHIER_PRO4
  33         bool "UniPhier Pro4 SoC"
  34         select ARCH_UNIPHIER_32BIT
  35
  36 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
  37         bool "UniPhier Pro5/PXs2/LD6b SoCs"
  38         select ARCH_UNIPHIER_32BIT
  39
  40 config ARCH_UNIPHIER_LD11_SINGLE
  41         bool "UniPhier LD11 SoC"
  42         select ARCH_UNIPHIER_64BIT
  43
  44 config ARCH_UNIPHIER_LD20_SINGLE
  45         bool "UniPhier LD20 SoC"
  46         select ARCH_UNIPHIER_64BIT
  47
  48 config ARCH_UNIPHIER_V8_MULTI
  49         bool "UniPhier V8 SoCs"
  50         depends on !SPL
  51         select ARCH_UNIPHIER_64BIT
  52
  53 endchoice
  54
  55 config ARCH_UNIPHIER_LD4
  56         bool "Enable UniPhier LD4 SoC support"
  57         depends on ARCH_UNIPHIER_LD4_SLD8
  58         default y
  59
  60 config ARCH_UNIPHIER_SLD8
  61         bool "Enable UniPhier sLD8 SoC support"
  62         depends on ARCH_UNIPHIER_LD4_SLD8
  63         default y
  64
  65 config ARCH_UNIPHIER_PRO5
  66         bool "Enable UniPhier Pro5 SoC support"
  67         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  68         default y
  69
  70 config ARCH_UNIPHIER_PXS2
  71         bool "Enable UniPhier Pxs2 SoC support"
  72         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  73         default y
  74
  75 config ARCH_UNIPHIER_LD6B
  76         bool "Enable UniPhier LD6b SoC support"
  77         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  78         default y
  79
  80 config ARCH_UNIPHIER_LD11
  81         bool "Enable UniPhier LD11 SoC support" if ARCH_UNIPHIER_V8_MULTI
  82         depends on ARCH_UNIPHIER_LD11_SINGLE || ARCH_UNIPHIER_V8_MULTI
  83         default y
  84
  85 config ARCH_UNIPHIER_LD20
  86         bool "Enable UniPhier LD20 SoC support" if ARCH_UNIPHIER_V8_MULTI
  87         depends on ARCH_UNIPHIER_LD20_SINGLE || ARCH_UNIPHIER_V8_MULTI
  88         select OF_BOARD_SETUP
  89         default y
  90
  91 config CACHE_UNIPHIER
  92         bool "Enable the UniPhier L2 cache controller"
  93         depends on ARCH_UNIPHIER_32BIT
  94         select SYS_CACHE_SHIFT_7
  95         default y
  96         help
  97           This option allows to use the UniPhier System Cache as L2 cache.
  98
  99 config MICRO_SUPPORT_CARD
 100         bool "Use Micro Support Card"
 101         help
 102           This option provides support for the expansion board, available
 103           on some UniPhier reference boards.
 104
 105           Say Y to use the on-board UART, Ether, LED devices.
 106
 107 config CMD_PINMON
 108         bool "Enable boot mode pins monitor command"
 109         default y
 110         help
 111           The command "pinmon" shows the state of the boot mode pins.
 112           The boot mode pins are latched when the system reset is deasserted
 113           and determine which device the system should load a boot image from.
 114
 115 config CMD_DDRPHY_DUMP
 116         bool "Enable dump command of DDR PHY parameters"
 117         depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \
 118                 ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11
 119         default y
 120         help
 121           The command "ddrphy" shows the resulting parameters of DDR PHY
 122           training; it is useful for the evaluation of DDR PHY training.
 123
 124 config CMD_DDRMPHY_DUMP
 125         bool "Enable dump command of DDR Multi PHY parameters"
 126         depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
 127         default y
 128         help
 129           The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
 130           training; it is useful for the evaluation of DDR Multi PHY training.
 131
 132 endif