board/Marvell/db-88f6820-amc/db-88f6820-amc.c

   1 /*
   2  * Copyright (C) 2015 Stefan Roese <sr@denx.de>
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <i2c.h>
   9 #include <miiphy.h>
  10 #include <netdev.h>
  11 #include <asm/io.h>
  12 #include <asm/arch/cpu.h>
  13 #include <asm/arch/soc.h>
  14
  15 #include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
  16 #include <../serdes/a38x/high_speed_env_spec.h>
  17
  18 DECLARE_GLOBAL_DATA_PTR;
  19
  20 #define ETH_PHY_CTRL_REG                0
  21 #define ETH_PHY_CTRL_POWER_DOWN_BIT     11
  22 #define ETH_PHY_CTRL_POWER_DOWN_MASK    (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
  23
  24 /*
  25  * Those values and defines are taken from the Marvell U-Boot version
  26  * "u-boot-2013.01-2016_T1.0.eng_drop_v10"
  27  */
  28 #define DB_AMC_88F68XX_GPP_OUT_ENA_LOW                                  \
  29         (~(BIT(29)))
  30 #define DB_AMC_88F68XX_GPP_OUT_ENA_MID                                  \
  31         (~(BIT(12) | BIT(17) | BIT(18) | BIT(20) | BIT(21)))
  32 #define DB_AMC_88F68XX_GPP_OUT_VAL_LOW  (BIT(29))
  33 #define DB_AMC_88F68XX_GPP_OUT_VAL_MID  0x0
  34 #define DB_AMC_88F68XX_GPP_OUT_VAL_HIGH 0x0
  35 #define DB_AMC_88F68XX_GPP_POL_LOW      0x0
  36 #define DB_AMC_88F68XX_GPP_POL_MID      0x0
  37
  38 static struct serdes_map board_serdes_map[] = {
  39         {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
  40         {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  41         {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  42         {DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  43         {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  44         {SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}
  45 };
  46
  47 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
  48 {
  49         *serdes_map_array = board_serdes_map;
  50         *count = ARRAY_SIZE(board_serdes_map);
  51         return 0;
  52 }
  53
  54 /*
  55  * Define the DDR layout / topology here in the board file. This will
  56  * be used by the DDR3 init code in the SPL U-Boot version to configure
  57  * the DDR3 controller.
  58  */
  59 static struct hws_topology_map board_topology_map = {
  60         0x1, /* active interfaces */
  61         /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
  62         { { { {0x1, 0, 0, 0},
  63               {0x1, 0, 0, 0},
  64               {0x1, 0, 0, 0},
  65               {0x1, 0, 0, 0},
  66               {0x1, 0, 0, 0} },
  67             SPEED_BIN_DDR_1866L,        /* speed_bin */
  68             BUS_WIDTH_8,                /* memory_width */
  69             MEM_2G,                     /* mem_size */
  70             DDR_FREQ_800,               /* frequency */
  71             0, 0,                       /* cas_wl cas_l */
  72             HWS_TEMP_LOW,               /* temperature */
  73             HWS_TIM_DEFAULT} },         /* timing */
  74         5,                              /* Num Of Bus Per Interface*/
  75         BUS_MASK_32BIT                  /* Busses mask */
  76 };
  77
  78 struct hws_topology_map *ddr3_get_topology_map(void)
  79 {
  80         /* Return the board topology as defined in the board code */
  81         return &board_topology_map;
  82 }
  83
  84 int board_early_init_f(void)
  85 {
  86         /* Configure MPP */
  87         writel(0x11111111, MVEBU_MPP_BASE + 0x00);
  88         writel(0x11111111, MVEBU_MPP_BASE + 0x04);
  89         writel(0x55066011, MVEBU_MPP_BASE + 0x08);
  90         writel(0x05055550, MVEBU_MPP_BASE + 0x0c);
  91         writel(0x05055555, MVEBU_MPP_BASE + 0x10);
  92         writel(0x01106565, MVEBU_MPP_BASE + 0x14);
  93         writel(0x40000000, MVEBU_MPP_BASE + 0x18);
  94         writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
  95
  96         /* Set GPP Out value */
  97         writel(DB_AMC_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
  98         writel(DB_AMC_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
  99
 100         /* Set GPP Polarity */
 101         writel(DB_AMC_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
 102         writel(DB_AMC_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
 103
 104         /* Set GPP Out Enable */
 105         writel(DB_AMC_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
 106         writel(DB_AMC_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
 107
 108         return 0;
 109 }
 110
 111 int board_init(void)
 112 {
 113         /* adress of boot parameters */
 114         gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 115
 116         return 0;
 117 }
 118
 119 int checkboard(void)
 120 {
 121         puts("Board: Marvell DB-88F6820-AMC\n");
 122
 123         return 0;
 124 }
 125
 126 int board_eth_init(bd_t *bis)
 127 {
 128         cpu_eth_init(bis); /* Built in controller(s) come first */
 129         return pci_eth_init(bis);
 130 }