3 * Michael Schwingen, michael@schwingen.org
6 * Stefan Roese, DENX Software Engineering, sr@denx.de.
9 * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
12 * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
13 * Marius Groeger <mgroeger@sysgo.de>
15 * SPDX-License-Identifier: GPL-2.0+
21 #include <asm/arch/ixp425.h>
26 #include <asm/arch/ixp425pci.h>
29 #include "actux4_hw.h"
31 DECLARE_GLOBAL_DATA_PTR
;
33 int board_early_init_f(void)
35 writel(0xbd113c42, IXP425_EXP_CS1
);
41 /* adress of boot parameters */
42 gd
->bd
->bi_boot_params
= 0x00000100;
44 GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON
);
45 GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON
);
47 GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST
);
48 GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST
);
50 /* led not populated on board*/
51 GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3
);
52 GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3
);
55 GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2
);
56 GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2
);
59 /* weak pulldown = LED weak on */
60 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1
);
61 GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1
);
63 /* Setup GPIO's for Interrupt inputs */
64 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA
);
65 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB
);
66 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC
);
67 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT
);
68 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA
);
69 GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB
);
71 GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA
);
72 GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB
);
73 GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC
);
74 GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT
);
75 GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA
);
76 GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB
);
78 /* Setup GPIO's for 33MHz clock output */
79 writel(0x011001FF, IXP425_GPIO_GPCLKR
);
80 GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK
);
81 GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK
);
84 GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST
);
86 GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST
);
88 GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST
);
93 /* Check Board Identity */
96 puts("Board: AcTux-4\n");
102 gd
->ram_size
= get_ram_size(CONFIG_SYS_SDRAM_BASE
, 128<<20);
107 struct pci_controller hose
;
109 void pci_init_board(void)
116 * Hardcoded flash setup:
117 * Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus.
118 * Flash 1 is an Intel *16 flash using the CFI driver.
120 ulong
board_flash_get_legacy(ulong base
, int banknum
, flash_info_t
*info
)
122 if (banknum
== 0) { /* non-CFI boot flash */
125 info
->interface
= FLASH_CFI_X8
;