]>
git.ipfire.org Git - people/ms/u-boot.git/blob - board/cmc_pu2/load_sernum_ethaddr.c
2 * (C) Copyright 2000, 2001, 2002
3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
6 * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
8 * See file CREDITS for list of people who contributed to this
11 * This program is free software; you can redistribute it and/or
12 * modify it under the terms of the GNU General Public License as
13 * published by the Free Software Foundation; either version 2 of
14 * the License, or (at your option) any later version.
16 * This program is distributed in the hope that it will be useful,
17 * but WITHOUT ANY WARRANTY; without even the implied warranty of
18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
19 * GNU General Public License for more details.
21 * You should have received a copy of the GNU General Public License
22 * along with this program; if not, write to the Free Software
23 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
32 #define I2C_CHIP 0x50 /* I2C bus address of onboard EEPROM */
33 #define I2C_ALEN 1 /* length of EEPROM addresses in bytes */
34 #define I2C_OFFSET 0x0 /* start address of manufacturere data block
37 /* 64 Byte manufacturer data block in EEPROM */
38 struct manufacturer_data
{
39 unsigned int serial_number
; /* serial number (0...999999) */
40 unsigned short hardware
; /* hardware version (e.g. V1.02) */
41 unsigned short manuf_date
; /* manufacture date (e.g. 25/02) */
42 unsigned char name
[20]; /* device name (in CHIP.INI) */
43 unsigned char macadr
[6]; /* MAC address */
44 signed char a_kal
[4]; /* calibration value for U */
45 signed char i_kal
[4]; /* calibration value for I */
46 unsigned char reserve
[18]; /* reserved */
47 unsigned short save_nr
; /* save count */
48 unsigned short chksum
; /* checksum */
52 int i2c_read (unsigned char chip
, unsigned int addr
, int alen
,
53 unsigned char *buffer
, int len
);
55 /*-----------------------------------------------------------------------
56 * Process manufacturer data block in EEPROM:
58 * If we boot on a system fresh from factory, check if the manufacturer data
59 * in the EEPROM is valid and save some information it contains.
61 * CMC manufacturer data is defined as follows:
63 * - located in the onboard EEPROM
64 * - starts at offset 0x0
67 * Internal structure: see struct definition
72 struct manufacturer_data data
;
74 unsigned short chksum
;
78 #if !defined(CONFIG_HARD_I2C) && !defined(CONFIG_SOFT_I2C)
79 #error you must define some I2C support (CONFIG_HARD_I2C or CONFIG_SOFT_I2C)
81 if (i2c_read(I2C_CHIP
, I2C_OFFSET
, I2C_ALEN
, (unsigned char *)&data
,
83 puts ("Error reading manufacturer data from EEPROM\n");
87 /* check if manufacturer data block is valid */
88 p
= (unsigned char *)&data
;
90 for (i
= 0; i
< (sizeof(data
) - sizeof(data
.chksum
)); i
++)
93 debug ("checksum of manufacturer data block: %#.4x\n", chksum
);
95 if (chksum
!= data
.chksum
) {
96 puts ("Error: manufacturer data block has invalid checksum\n");
100 /* copy serial number */
101 sprintf (serial
, "%d", data
.serial_number
);
103 /* set serial# and ethaddr if not yet defined */
104 if (getenv("serial#") == NULL
) {
105 setenv ("serial#", serial
);
108 if (getenv("ethaddr") == NULL
) {
109 eth_setenv_enetaddr("ethaddr", data
.macadr
);