board/davinci/da8xxevm/da850evm.c

   1 /*
   2  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
   3  *
   4  * Based on da830evm.c. Original Copyrights follow:
   5  *
   6  * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
   7  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11
  12 #include <common.h>
  13 #include <i2c.h>
  14 #include <net.h>
  15 #include <netdev.h>
  16 #include <spi.h>
  17 #include <spi_flash.h>
  18 #include <asm/arch/hardware.h>
  19 #include <asm/ti-common/davinci_nand.h>
  20 #include <asm/arch/emac_defs.h>
  21 #include <asm/arch/pinmux_defs.h>
  22 #include <asm/io.h>
  23 #include <asm/arch/davinci_misc.h>
  24 #include <linux/errno.h>
  25 #include <hwconfig.h>
  26 #include <asm/mach-types.h>
  27
  28 #ifdef CONFIG_MMC_DAVINCI
  29 #include <mmc.h>
  30 #include <asm/arch/sdmmc_defs.h>
  31 #endif
  32
  33 DECLARE_GLOBAL_DATA_PTR;
  34
  35 #ifdef CONFIG_DRIVER_TI_EMAC
  36 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
  37 #define HAS_RMII 1
  38 #else
  39 #define HAS_RMII 0
  40 #endif
  41 #endif /* CONFIG_DRIVER_TI_EMAC */
  42
  43 #define CFG_MAC_ADDR_SPI_BUS    0
  44 #define CFG_MAC_ADDR_SPI_CS     0
  45 #define CFG_MAC_ADDR_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
  46 #define CFG_MAC_ADDR_SPI_MODE   SPI_MODE_3
  47
  48 #define CFG_MAC_ADDR_OFFSET     (flash->size - SZ_64K)
  49
  50 #ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
  51 static int get_mac_addr(u8 *addr)
  52 {
  53         struct spi_flash *flash;
  54         int ret;
  55
  56         flash = spi_flash_probe(CFG_MAC_ADDR_SPI_BUS, CFG_MAC_ADDR_SPI_CS,
  57                         CFG_MAC_ADDR_SPI_MAX_HZ, CFG_MAC_ADDR_SPI_MODE);
  58         if (!flash) {
  59                 printf("Error - unable to probe SPI flash.\n");
  60                 return -1;
  61         }
  62
  63         ret = spi_flash_read(flash, CFG_MAC_ADDR_OFFSET, 6, addr);
  64         if (ret) {
  65                 printf("Error - unable to read MAC address from SPI flash.\n");
  66                 return -1;
  67         }
  68
  69         return ret;
  70 }
  71 #endif
  72
  73 void dsp_lpsc_on(unsigned domain, unsigned int id)
  74 {
  75         dv_reg_p mdstat, mdctl, ptstat, ptcmd;
  76         struct davinci_psc_regs *psc_regs;
  77
  78         psc_regs = davinci_psc0_regs;
  79         mdstat = &psc_regs->psc0.mdstat[id];
  80         mdctl = &psc_regs->psc0.mdctl[id];
  81         ptstat = &psc_regs->ptstat;
  82         ptcmd = &psc_regs->ptcmd;
  83
  84         while (*ptstat & (0x1 << domain))
  85                 ;
  86
  87         if ((*mdstat & 0x1f) == 0x03)
  88                 return;                 /* Already on and enabled */
  89
  90         *mdctl |= 0x03;
  91
  92         *ptcmd = 0x1 << domain;
  93
  94         while (*ptstat & (0x1 << domain))
  95                 ;
  96         while ((*mdstat & 0x1f) != 0x03)
  97                 ;               /* Probably an overkill... */
  98 }
  99
 100 static void dspwake(void)
 101 {
 102         unsigned *resetvect = (unsigned *)DAVINCI_L3CBARAM_BASE;
 103         u32 val;
 104
 105         /* if the device is ARM only, return */
 106         if ((readl(CHIP_REV_ID_REG) & 0x3f) == 0x10)
 107                 return;
 108
 109         if (hwconfig_subarg_cmp_f("dsp", "wake", "no", NULL))
 110                 return;
 111
 112         *resetvect++ = 0x1E000; /* DSP Idle */
 113         /* clear out the next 10 words as NOP */
 114         memset(resetvect, 0, sizeof(unsigned) *10);
 115
 116         /* setup the DSP reset vector */
 117         writel(DAVINCI_L3CBARAM_BASE, HOST1CFG);
 118
 119         dsp_lpsc_on(1, DAVINCI_LPSC_GEM);
 120         val = readl(PSC0_MDCTL + (15 * 4));
 121         val |= 0x100;
 122         writel(val, (PSC0_MDCTL + (15 * 4)));
 123 }
 124
 125 int misc_init_r(void)
 126 {
 127         dspwake();
 128
 129 #if defined(CONFIG_MAC_ADDR_IN_SPIFLASH) || defined(CONFIG_MAC_ADDR_IN_EEPROM)
 130
 131         uchar env_enetaddr[6];
 132         int enetaddr_found;
 133
 134         enetaddr_found = eth_env_get_enetaddr("ethaddr", env_enetaddr);
 135
 136 #endif
 137
 138 #ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
 139         int spi_mac_read;
 140         uchar buff[6];
 141
 142         spi_mac_read = get_mac_addr(buff);
 143
 144         /*
 145          * MAC address not present in the environment
 146          * try and read the MAC address from SPI flash
 147          * and set it.
 148          */
 149         if (!enetaddr_found) {
 150                 if (!spi_mac_read) {
 151                         if (is_valid_ethaddr(buff)) {
 152                                 if (eth_env_set_enetaddr("ethaddr", buff)) {
 153                                         printf("Warning: Failed to "
 154                                         "set MAC address from SPI flash\n");
 155                                 }
 156                         } else {
 157                                         printf("Warning: Invalid "
 158                                         "MAC address read from SPI flash\n");
 159                         }
 160                 }
 161         } else {
 162                 /*
 163                  * MAC address present in environment compare it with
 164                  * the MAC address in SPI flash and warn on mismatch
 165                  */
 166                 if (!spi_mac_read && is_valid_ethaddr(buff) &&
 167                     memcmp(env_enetaddr, buff, 6))
 168                         printf("Warning: MAC address in SPI flash don't match "
 169                                         "with the MAC address in the environment\n");
 170                 printf("Default using MAC address from environment\n");
 171         }
 172
 173 #elif defined(CONFIG_MAC_ADDR_IN_EEPROM)
 174         uint8_t enetaddr[8];
 175         int eeprom_mac_read;
 176
 177         /* Read Ethernet MAC address from EEPROM */
 178         eeprom_mac_read = dvevm_read_mac_address(enetaddr);
 179
 180         /*
 181          * MAC address not present in the environment
 182          * try and read the MAC address from EEPROM flash
 183          * and set it.
 184          */
 185         if (!enetaddr_found) {
 186                 if (eeprom_mac_read)
 187                         /* Set Ethernet MAC address from EEPROM */
 188                         davinci_sync_env_enetaddr(enetaddr);
 189         } else {
 190                 /*
 191                  * MAC address present in environment compare it with
 192                  * the MAC address in EEPROM and warn on mismatch
 193                  */
 194                 if (eeprom_mac_read && memcmp(enetaddr, env_enetaddr, 6))
 195                         printf("Warning: MAC address in EEPROM don't match "
 196                                         "with the MAC address in the environment\n");
 197                 printf("Default using MAC address from environment\n");
 198         }
 199
 200 #endif
 201         return 0;
 202 }
 203
 204 #ifdef CONFIG_MMC_DAVINCI
 205 static struct davinci_mmc mmc_sd0 = {
 206         .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
 207         .host_caps = MMC_MODE_4BIT,     /* DA850 supports only 4-bit SD/MMC */
 208         .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
 209         .version = MMC_CTLR_VERSION_2,
 210 };
 211
 212 int board_mmc_init(bd_t *bis)
 213 {
 214         mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID);
 215
 216         /* Add slot-0 to mmc subsystem */
 217         return davinci_mmc_init(bis, &mmc_sd0);
 218 }
 219 #endif
 220
 221 static const struct pinmux_config gpio_pins[] = {
 222 #ifdef CONFIG_USE_NOR
 223         /* GP0[11] is required for NOR to work on Rev 3 EVMs */
 224         { pinmux(0), 8, 4 },    /* GP0[11] */
 225 #endif
 226 #ifdef CONFIG_MMC_DAVINCI
 227         /* GP0[11] is required for SD to work on Rev 3 EVMs */
 228         { pinmux(0),  8, 4 },   /* GP0[11] */
 229 #endif
 230 };
 231
 232 const struct pinmux_resource pinmuxes[] = {
 233 #ifdef CONFIG_DRIVER_TI_EMAC
 234         PINMUX_ITEM(emac_pins_mdio),
 235 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
 236         PINMUX_ITEM(emac_pins_rmii),
 237 #else
 238         PINMUX_ITEM(emac_pins_mii),
 239 #endif
 240 #endif
 241 #ifdef CONFIG_SPI_FLASH
 242         PINMUX_ITEM(spi1_pins_base),
 243         PINMUX_ITEM(spi1_pins_scs0),
 244 #endif
 245         PINMUX_ITEM(uart2_pins_txrx),
 246         PINMUX_ITEM(uart2_pins_rtscts),
 247         PINMUX_ITEM(i2c0_pins),
 248 #ifdef CONFIG_NAND_DAVINCI
 249         PINMUX_ITEM(emifa_pins_cs3),
 250         PINMUX_ITEM(emifa_pins_cs4),
 251         PINMUX_ITEM(emifa_pins_nand),
 252 #elif defined(CONFIG_USE_NOR)
 253         PINMUX_ITEM(emifa_pins_cs2),
 254         PINMUX_ITEM(emifa_pins_nor),
 255 #endif
 256         PINMUX_ITEM(gpio_pins),
 257 #ifdef CONFIG_MMC_DAVINCI
 258         PINMUX_ITEM(mmc0_pins),
 259 #endif
 260 };
 261
 262 const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
 263
 264 const struct lpsc_resource lpsc[] = {
 265         { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
 266         { DAVINCI_LPSC_SPI1 },  /* Serial Flash */
 267         { DAVINCI_LPSC_EMAC },  /* image download */
 268         { DAVINCI_LPSC_UART2 }, /* console */
 269         { DAVINCI_LPSC_GPIO },
 270 #ifdef CONFIG_MMC_DAVINCI
 271         { DAVINCI_LPSC_MMC_SD },
 272 #endif
 273 };
 274
 275 const int lpsc_size = ARRAY_SIZE(lpsc);
 276
 277 #ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
 278 #define CONFIG_DA850_EVM_MAX_CPU_CLK    300000000
 279 #endif
 280
 281 #define REV_AM18X_EVM           0x100
 282
 283 /*
 284  * get_board_rev() - setup to pass kernel board revision information
 285  * Returns:
 286  * bit[0-3]     Maximum cpu clock rate supported by onboard SoC
 287  *              0000b - 300 MHz
 288  *              0001b - 372 MHz
 289  *              0010b - 408 MHz
 290  *              0011b - 456 MHz
 291  */
 292 u32 get_board_rev(void)
 293 {
 294         char *s;
 295         u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
 296         u32 rev = 0;
 297
 298         s = env_get("maxcpuclk");
 299         if (s)
 300                 maxcpuclk = simple_strtoul(s, NULL, 10);
 301
 302         if (maxcpuclk >= 456000000)
 303                 rev = 3;
 304         else if (maxcpuclk >= 408000000)
 305                 rev = 2;
 306         else if (maxcpuclk >= 372000000)
 307                 rev = 1;
 308 #ifdef CONFIG_DA850_AM18X_EVM
 309         rev |= REV_AM18X_EVM;
 310 #endif
 311         return rev;
 312 }
 313
 314 int board_early_init_f(void)
 315 {
 316         /*
 317          * Power on required peripherals
 318          * ARM does not have access by default to PSC0 and PSC1
 319          * assuming here that the DSP bootloader has set the IOPU
 320          * such that PSC access is available to ARM
 321          */
 322         if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
 323                 return 1;
 324
 325         return 0;
 326 }
 327
 328 int board_init(void)
 329 {
 330         irq_init();
 331
 332 #ifdef CONFIG_NAND_DAVINCI
 333         /*
 334          * NAND CS setup - cycle counts based on da850evm NAND timings in the
 335          * Linux kernel @ 25MHz EMIFA
 336          */
 337         writel((DAVINCI_ABCR_WSETUP(2) |
 338                 DAVINCI_ABCR_WSTROBE(2) |
 339                 DAVINCI_ABCR_WHOLD(1) |
 340                 DAVINCI_ABCR_RSETUP(1) |
 341                 DAVINCI_ABCR_RSTROBE(4) |
 342                 DAVINCI_ABCR_RHOLD(0) |
 343                 DAVINCI_ABCR_TA(1) |
 344                 DAVINCI_ABCR_ASIZE_8BIT),
 345                &davinci_emif_regs->ab2cr); /* CS3 */
 346 #endif
 347
 348         /* arch number of the board */
 349         gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;
 350
 351         /* address of boot parameters */
 352         gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 353
 354         /* setup the SUSPSRC for ARM to control emulation suspend */
 355         writel(readl(&davinci_syscfg_regs->suspsrc) &
 356                ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
 357                  DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
 358                  DAVINCI_SYSCFG_SUSPSRC_UART2),
 359                &davinci_syscfg_regs->suspsrc);
 360
 361         /* configure pinmux settings */
 362         if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
 363                 return 1;
 364
 365 #ifdef CONFIG_USE_NOR
 366         /* Set the GPIO direction as output */
 367         clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
 368
 369         /* Set the output as low */
 370         writel(0x01 << 11, GPIO_BANK0_REG_CLR_ADDR);
 371 #endif
 372
 373 #ifdef CONFIG_MMC_DAVINCI
 374         /* Set the GPIO direction as output */
 375         clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
 376
 377         /* Set the output as high */
 378         writel(0x01 << 11, GPIO_BANK0_REG_SET_ADDR);
 379 #endif
 380
 381 #ifdef CONFIG_DRIVER_TI_EMAC
 382         davinci_emac_mii_mode_sel(HAS_RMII);
 383 #endif /* CONFIG_DRIVER_TI_EMAC */
 384
 385         /* enable the console UART */
 386         writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
 387                 DAVINCI_UART_PWREMU_MGMT_UTRST),
 388                &davinci_uart2_ctrl_regs->pwremu_mgmt);
 389
 390         return 0;
 391 }
 392
 393 #ifdef CONFIG_DRIVER_TI_EMAC
 394
 395 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
 396 /**
 397  * rmii_hw_init
 398  *
 399  * DA850/OMAP-L138 EVM can interface to a daughter card for
 400  * additional features. This card has an I2C GPIO Expander TCA6416
 401  * to select the required functions like camera, RMII Ethernet,
 402  * character LCD, video.
 403  *
 404  * Initialization of the expander involves configuring the
 405  * polarity and direction of the ports. P07-P05 are used here.
 406  * These ports are connected to a Mux chip which enables only one
 407  * functionality at a time.
 408  *
 409  * For RMII phy to respond, the MII MDIO clock has to be  disabled
 410  * since both the PHY devices have address as zero. The MII MDIO
 411  * clock is controlled via GPIO2[6].
 412  *
 413  * This code is valid for Beta version of the hardware
 414  */
 415 int rmii_hw_init(void)
 416 {
 417         const struct pinmux_config gpio_pins[] = {
 418                 { pinmux(6), 8, 1 }
 419         };
 420         u_int8_t buf[2];
 421         unsigned int temp;
 422         int ret;
 423
 424         /* PinMux for GPIO */
 425         if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
 426                 return 1;
 427
 428         /* I2C Exapnder configuration */
 429         /* Set polarity to non-inverted */
 430         buf[0] = 0x0;
 431         buf[1] = 0x0;
 432         ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 4, 1, buf, 2);
 433         if (ret) {
 434                 printf("\nExpander @ 0x%02x write FAILED!!!\n",
 435                                 CONFIG_SYS_I2C_EXPANDER_ADDR);
 436                 return ret;
 437         }
 438
 439         /* Configure P07-P05 as outputs */
 440         buf[0] = 0x1f;
 441         buf[1] = 0xff;
 442         ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 6, 1, buf, 2);
 443         if (ret) {
 444                 printf("\nExpander @ 0x%02x write FAILED!!!\n",
 445                                 CONFIG_SYS_I2C_EXPANDER_ADDR);
 446         }
 447
 448         /* For Ethernet RMII selection
 449          * P07(SelA)=0
 450          * P06(SelB)=1
 451          * P05(SelC)=1
 452          */
 453         if (i2c_read(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
 454                 printf("\nExpander @ 0x%02x read FAILED!!!\n",
 455                                 CONFIG_SYS_I2C_EXPANDER_ADDR);
 456         }
 457
 458         buf[0] &= 0x1f;
 459         buf[0] |= (0 << 7) | (1 << 6) | (1 << 5);
 460         if (i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
 461                 printf("\nExpander @ 0x%02x write FAILED!!!\n",
 462                                 CONFIG_SYS_I2C_EXPANDER_ADDR);
 463         }
 464
 465         /* Set the output as high */
 466         temp = REG(GPIO_BANK2_REG_SET_ADDR);
 467         temp |= (0x01 << 6);
 468         REG(GPIO_BANK2_REG_SET_ADDR) = temp;
 469
 470         /* Set the GPIO direction as output */
 471         temp = REG(GPIO_BANK2_REG_DIR_ADDR);
 472         temp &= ~(0x01 << 6);
 473         REG(GPIO_BANK2_REG_DIR_ADDR) = temp;
 474
 475         return 0;
 476 }
 477 #endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */
 478
 479 /*
 480  * Initializes on-board ethernet controllers.
 481  */
 482 int board_eth_init(bd_t *bis)
 483 {
 484 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
 485         /* Select RMII fucntion through the expander */
 486         if (rmii_hw_init())
 487                 printf("RMII hardware init failed!!!\n");
 488 #endif
 489         if (!davinci_emac_initialize()) {
 490                 printf("Error: Ethernet init failed!\n");
 491                 return -1;
 492         }
 493
 494         return 0;
 495 }
 496 #endif /* CONFIG_DRIVER_TI_EMAC */