board/freescale/t4rdb/ddr.c

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <i2c.h>
   9 #include <hwconfig.h>
  10 #include <asm/mmu.h>
  11 #include <fsl_ddr_sdram.h>
  12 #include <fsl_ddr_dimm_params.h>
  13 #include <asm/fsl_law.h>
  14 #include "ddr.h"
  15
  16 DECLARE_GLOBAL_DATA_PTR;
  17
  18 void fsl_ddr_board_options(memctl_options_t *popts,
  19                                 dimm_params_t *pdimm,
  20                                 unsigned int ctrl_num)
  21 {
  22         const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  23         ulong ddr_freq;
  24
  25         if (ctrl_num > 2) {
  26                 printf("Not supported controller number %d\n", ctrl_num);
  27                 return;
  28         }
  29         if (!pdimm->n_ranks)
  30                 return;
  31
  32         /*
  33          * we use identical timing for all slots. If needed, change the code
  34          * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
  35          */
  36         if (popts->registered_dimm_en)
  37                 pbsp = rdimms[0];
  38         else
  39                 pbsp = udimms[0];
  40
  41
  42         /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
  43          * freqency and n_banks specified in board_specific_parameters table.
  44          */
  45         ddr_freq = get_ddr_freq(0) / 1000000;
  46         while (pbsp->datarate_mhz_high) {
  47                 if (pbsp->n_ranks == pdimm->n_ranks &&
  48                     (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
  49                         if (ddr_freq <= pbsp->datarate_mhz_high) {
  50                                 popts->clk_adjust = pbsp->clk_adjust;
  51                                 popts->wrlvl_start = pbsp->wrlvl_start;
  52                                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  53                                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  54                                 goto found;
  55                         }
  56                         pbsp_highest = pbsp;
  57                 }
  58                 pbsp++;
  59         }
  60
  61         if (pbsp_highest) {
  62                 printf("Error: board specific timing not found for data\n"
  63                         "rate %lu MT/s\n"
  64                         "Trying to use the highest speed (%u) parameters\n",
  65                         ddr_freq, pbsp_highest->datarate_mhz_high);
  66                 popts->clk_adjust = pbsp_highest->clk_adjust;
  67                 popts->wrlvl_start = pbsp_highest->wrlvl_start;
  68                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  69                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  70         } else {
  71                 panic("DIMM is not supported by this board");
  72         }
  73 found:
  74         debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
  75                 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n"
  76                 "wrlvl_ctrl_3 0x%x\n",
  77                 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
  78                 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
  79                 pbsp->wrlvl_ctl_3);
  80
  81         /*
  82          * Factors to consider for half-strength driver enable:
  83          *      - number of DIMMs installed
  84          */
  85         popts->half_strength_driver_enable = 0;
  86         /*
  87          * Write leveling override
  88          */
  89         popts->wrlvl_override = 1;
  90         popts->wrlvl_sample = 0xf;
  91
  92         /*
  93          * Rtt and Rtt_WR override
  94          */
  95         popts->rtt_override = 0;
  96
  97         /* Enable ZQ calibration */
  98         popts->zq_en = 1;
  99
 100         /* DHC_EN =1, ODT = 75 Ohm */
 101         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
 102         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
 103 }
 104
 105 phys_size_t initdram(int board_type)
 106 {
 107         phys_size_t dram_size;
 108
 109         puts("Initializing....using SPD\n");
 110
 111 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 112         dram_size = fsl_ddr_sdram();
 113
 114         dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 115         dram_size *= 0x100000;
 116 #else
 117         /* DDR has been initialised by first stage boot loader */
 118         dram_size = fsl_ddr_sdram_size();
 119 #endif
 120
 121         return dram_size;
 122 }