board/karo/tx25/tx25.c

   1 /*
   2  * (C) Copyright 2009 DENX Software Engineering
   3  * Author: John Rigby <jrigby@gmail.com>
   4  *
   5  * Based on imx27lite.c:
   6  *   Copyright (C) 2008,2009 Eric Jarrige <jorasse@users.sourceforge.net>
   7  *   Copyright (C) 2009 Ilya Yanok <yanok@emcraft.com>
   8  * And:
   9  *   RedBoot tx25_misc.c Copyright (C) 2009 Red Hat
  10  *
  11  * This program is free software; you can redistribute it and/or
  12  * modify it under the terms of the GNU General Public License as
  13  * published by the Free Software Foundation; either version 2 of
  14  * the License, or (at your option) any later version.
  15  *
  16  * This program is distributed in the hope that it will be useful,
  17  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  18  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  19  * GNU General Public License for more details.
  20  *
  21  * You should have received a copy of the GNU General Public License
  22  * along with this program; if not, write to the Free Software
  23  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  24  * MA 02111-1307 USA
  25  *
  26  */
  27 #include <common.h>
  28 #include <asm/io.h>
  29 #include <asm/arch/imx-regs.h>
  30 #include <asm/arch/imx25-pinmux.h>
  31 #include <asm/gpio.h>
  32 #include <asm/arch/sys_proto.h>
  33
  34 DECLARE_GLOBAL_DATA_PTR;
  35
  36 #ifdef CONFIG_FEC_MXC
  37 #define GPIO_FEC_RESET_B        IMX_GPIO_NR(4, 7)
  38 #define GPIO_FEC_ENABLE_B       IMX_GPIO_NR(4, 9)
  39 void tx25_fec_init(void)
  40 {
  41         struct iomuxc_mux_ctl *muxctl;
  42         struct iomuxc_pad_ctl *padctl;
  43         u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5);
  44         u32 saved_rdata0_mode, saved_rdata1_mode, saved_rx_dv_mode;
  45
  46         debug("tx25_fec_init\n");
  47         /*
  48          * fec pin init is generic
  49          */
  50         mx25_fec_init_pins();
  51
  52         /*
  53          * Set up the FEC_RESET_B and FEC_ENABLE GPIO pins.
  54          *
  55          * FEC_RESET_B: gpio4[7] is ALT 5 mode of pin D13
  56          * FEC_ENABLE_B: gpio4[9] is ALT 5 mode of pin D11
  57          */
  58         muxctl = (struct iomuxc_mux_ctl *)IMX_IOPADMUX_BASE;
  59         padctl = (struct iomuxc_pad_ctl *)IMX_IOPADCTL_BASE;
  60
  61         writel(gpio_mux_mode, &muxctl->pad_d13);
  62         writel(gpio_mux_mode, &muxctl->pad_d11);
  63
  64         writel(0x0, &padctl->pad_d13);
  65         writel(0x0, &padctl->pad_d11);
  66
  67         /* drop PHY power and assert reset (low) */
  68         gpio_direction_output(GPIO_FEC_RESET_B, 0);
  69         gpio_direction_output(GPIO_FEC_ENABLE_B, 0);
  70
  71         mdelay(5);
  72
  73         debug("resetting phy\n");
  74
  75         /* turn on PHY power leaving reset asserted */
  76         gpio_set_value(GPIO_FEC_ENABLE_B, 1);
  77
  78         mdelay(10);
  79
  80         /*
  81          * Setup some strapping pins that are latched by the PHY
  82          * as reset goes high.
  83          *
  84          * Set PHY mode to 111
  85          *  mode0 comes from FEC_RDATA0 which is GPIO 3_10 in mux mode 5
  86          *  mode1 comes from FEC_RDATA1 which is GPIO 3_11 in mux mode 5
  87          *  mode2 is tied high so nothing to do
  88          *
  89          * Turn on RMII mode
  90          *  RMII mode is selected by FEC_RX_DV which is GPIO 3_12 in mux mode
  91          */
  92         /*
  93          * save three current mux modes and set each to gpio mode
  94          */
  95         saved_rdata0_mode = readl(&muxctl->pad_fec_rdata0);
  96         saved_rdata1_mode = readl(&muxctl->pad_fec_rdata1);
  97         saved_rx_dv_mode = readl(&muxctl->pad_fec_rx_dv);
  98
  99         writel(gpio_mux_mode, &muxctl->pad_fec_rdata0);
 100         writel(gpio_mux_mode, &muxctl->pad_fec_rdata1);
 101         writel(gpio_mux_mode, &muxctl->pad_fec_rx_dv);
 102
 103         /*
 104          * set each to 1 and make each an output
 105          */
 106         gpio_direction_output(IMX_GPIO_NR(3, 10), 1);
 107         gpio_direction_output(IMX_GPIO_NR(3, 11), 1);
 108         gpio_direction_output(IMX_GPIO_NR(3, 12), 1);
 109
 110         mdelay(22);             /* this value came from RedBoot */
 111
 112         /*
 113          * deassert PHY reset
 114          */
 115         gpio_set_value(GPIO_FEC_RESET_B, 1);
 116
 117         mdelay(5);
 118
 119         /*
 120          * set FEC pins back
 121          */
 122         writel(saved_rdata0_mode, &muxctl->pad_fec_rdata0);
 123         writel(saved_rdata1_mode, &muxctl->pad_fec_rdata1);
 124         writel(saved_rx_dv_mode, &muxctl->pad_fec_rx_dv);
 125 }
 126 #else
 127 #define tx25_fec_init()
 128 #endif
 129
 130 int board_init()
 131 {
 132 #ifdef CONFIG_MXC_UART
 133         mx25_uart1_init_pins();
 134 #endif
 135         /* board id for linux */
 136         gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 137         return 0;
 138 }
 139
 140 int board_late_init(void)
 141 {
 142         tx25_fec_init();
 143         return 0;
 144 }
 145
 146 int dram_init(void)
 147 {
 148         /* dram_init must store complete ramsize in gd->ram_size */
 149         gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
 150                                 PHYS_SDRAM_1_SIZE);
 151         return 0;
 152 }
 153
 154 void dram_init_banksize(void)
 155 {
 156         gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 157         gd->bd->bi_dram[0].size = get_ram_size((void *)PHYS_SDRAM_1,
 158                         PHYS_SDRAM_1_SIZE);
 159 #if CONFIG_NR_DRAM_BANKS > 1
 160         gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
 161         gd->bd->bi_dram[1].size = get_ram_size((void *)PHYS_SDRAM_2,
 162                         PHYS_SDRAM_2_SIZE);
 163 #else
 164
 165 #endif
 166 }
 167
 168 int checkboard(void)
 169 {
 170         printf("KARO TX25\n");
 171         return 0;
 172 }