board/liebherr/mccmon6/mccmon6.c

   1 /*
   2  * Copyright (C) 2016-2017
   3  * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #include <common.h>
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/iomux.h>
  11 #include <asm/arch/imx-regs.h>
  12 #include <asm/arch/mx6-pins.h>
  13 #include <asm/arch/sys_proto.h>
  14 #include <asm/gpio.h>
  15 #include <asm/mach-imx/iomux-v3.h>
  16 #include <asm/mach-imx/mxc_i2c.h>
  17 #include <asm/mach-imx/spi.h>
  18 #include <asm/mach-imx/boot_mode.h>
  19 #include <asm/io.h>
  20 #include <fsl_esdhc.h>
  21 #include <mmc.h>
  22 #include <netdev.h>
  23 #include <micrel.h>
  24 #include <phy.h>
  25 #include <input.h>
  26 #include <i2c.h>
  27 #include <spl.h>
  28
  29 DECLARE_GLOBAL_DATA_PTR;
  30
  31 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  32         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  33         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  34
  35 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |                    \
  36         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  37         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  38
  39 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  40         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  41
  42 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED |         \
  43         PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  44
  45 #define I2C_PAD_CTRL    (PAD_CTL_PUS_100K_UP |                  \
  46         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |   \
  47         PAD_CTL_ODE | PAD_CTL_SRE_FAST)
  48
  49 #define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |          \
  50         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  51         PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
  52
  53 #define USDHC2_CD_GPIO          IMX_GPIO_NR(1, 4)
  54 #define ETH_PHY_RESET           IMX_GPIO_NR(1, 27)
  55 #define ECSPI3_CS0              IMX_GPIO_NR(4, 24)
  56 #define ECSPI3_FLWP             IMX_GPIO_NR(4, 27)
  57 #define NOR_WP                  IMX_GPIO_NR(1, 1)
  58 #define DISPLAY_EN              IMX_GPIO_NR(1, 2)
  59
  60 int dram_init(void)
  61 {
  62         gd->ram_size = imx_ddr_size();
  63
  64         return 0;
  65 }
  66
  67 static iomux_v3_cfg_t const uart1_pads[] = {
  68         IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
  69         IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
  70 };
  71
  72 static iomux_v3_cfg_t const usdhc2_pads[] = {
  73         IOMUX_PADS(PAD_SD2_CLK__SD2_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  74         IOMUX_PADS(PAD_SD2_CMD__SD2_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  75         IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  76         IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  77         IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  78         IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  79         /* Carrier MicroSD Card Detect */
  80         IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04  | MUX_PAD_CTRL(NO_PAD_CTRL)),
  81 };
  82
  83 static iomux_v3_cfg_t const usdhc3_pads[] = {
  84         IOMUX_PADS(PAD_SD3_CLK__SD3_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  85         IOMUX_PADS(PAD_SD3_CMD__SD3_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  86         IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  87         IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  88         IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  89         IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  90         IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  91         IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  92         IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  93         IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  94         IOMUX_PADS(PAD_SD3_RST__SD3_RESET  | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  95 };
  96
  97 static iomux_v3_cfg_t const enet_pads[] = {
  98         IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
  99         IOMUX_PADS(PAD_ENET_MDC__ENET_MDC    | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 100         IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 101         IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 102         IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 103         IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 104         IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 105         IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL
 106                    | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 107         IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK
 108                    | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 109         IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 110         IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 111         IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 112         IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 113         IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3  | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 114         IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL
 115                    | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 116         /* KSZ9031 PHY Reset */
 117         IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27  | MUX_PAD_CTRL(NO_PAD_CTRL)),
 118 };
 119
 120 static void setup_iomux_uart(void)
 121 {
 122         SETUP_IOMUX_PADS(uart1_pads);
 123 }
 124
 125 static void setup_iomux_enet(void)
 126 {
 127         SETUP_IOMUX_PADS(enet_pads);
 128
 129         /* Reset KSZ9031 PHY */
 130         gpio_direction_output(ETH_PHY_RESET, 0);
 131         mdelay(10);
 132         gpio_set_value(ETH_PHY_RESET, 1);
 133         udelay(100);
 134 }
 135
 136 static struct fsl_esdhc_cfg usdhc_cfg[2] = {
 137         {USDHC3_BASE_ADDR},
 138         {USDHC2_BASE_ADDR},
 139 };
 140
 141 int board_mmc_getcd(struct mmc *mmc)
 142 {
 143         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 144         int ret = 0;
 145
 146         switch (cfg->esdhc_base) {
 147         case USDHC2_BASE_ADDR:
 148                 ret = !gpio_get_value(USDHC2_CD_GPIO);
 149                 break;
 150         case USDHC3_BASE_ADDR:
 151                 /*
 152                  * eMMC don't have card detect pin - since it is soldered to the
 153                  * PCB board
 154                  */
 155                 ret = 1;
 156                 break;
 157         }
 158         return ret;
 159 }
 160
 161 int board_mmc_init(bd_t *bis)
 162 {
 163         int ret;
 164         u32 index = 0;
 165
 166         /*
 167          * MMC MAP
 168          * (U-Boot device node)    (Physical Port)
 169          * mmc0                    Soldered on board eMMC device
 170          * mmc1                    MicroSD card
 171          */
 172         for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
 173                 switch (index) {
 174                 case 0:
 175                         SETUP_IOMUX_PADS(usdhc3_pads);
 176                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 177                         usdhc_cfg[0].max_bus_width = 8;
 178                         break;
 179                 case 1:
 180                         SETUP_IOMUX_PADS(usdhc2_pads);
 181                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 182                         usdhc_cfg[1].max_bus_width = 4;
 183                         gpio_direction_input(USDHC2_CD_GPIO);
 184                         break;
 185                 default:
 186                         printf("Warning: More USDHC controllers (%d) than supported (%d)\n",
 187                                index + 1, CONFIG_SYS_FSL_USDHC_NUM);
 188                         return -EINVAL;
 189                 }
 190
 191                 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
 192                 if (ret)
 193                         return ret;
 194         }
 195
 196         return 0;
 197 }
 198
 199 static iomux_v3_cfg_t const eimnor_pads[] = {
 200         IOMUX_PADS(PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 201         IOMUX_PADS(PAD_EIM_D17__EIM_DATA17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 202         IOMUX_PADS(PAD_EIM_D18__EIM_DATA18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 203         IOMUX_PADS(PAD_EIM_D19__EIM_DATA19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 204         IOMUX_PADS(PAD_EIM_D20__EIM_DATA20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 205         IOMUX_PADS(PAD_EIM_D21__EIM_DATA21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 206         IOMUX_PADS(PAD_EIM_D22__EIM_DATA22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 207         IOMUX_PADS(PAD_EIM_D23__EIM_DATA23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 208         IOMUX_PADS(PAD_EIM_D24__EIM_DATA24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 209         IOMUX_PADS(PAD_EIM_D25__EIM_DATA25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 210         IOMUX_PADS(PAD_EIM_D26__EIM_DATA26 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 211         IOMUX_PADS(PAD_EIM_D27__EIM_DATA27 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 212         IOMUX_PADS(PAD_EIM_D28__EIM_DATA28 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 213         IOMUX_PADS(PAD_EIM_D29__EIM_DATA29 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 214         IOMUX_PADS(PAD_EIM_D30__EIM_DATA30 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 215         IOMUX_PADS(PAD_EIM_D31__EIM_DATA31 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 216         IOMUX_PADS(PAD_EIM_DA0__EIM_AD00   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 217         IOMUX_PADS(PAD_EIM_DA1__EIM_AD01   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 218         IOMUX_PADS(PAD_EIM_DA2__EIM_AD02   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 219         IOMUX_PADS(PAD_EIM_DA3__EIM_AD03   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 220         IOMUX_PADS(PAD_EIM_DA4__EIM_AD04   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 221         IOMUX_PADS(PAD_EIM_DA5__EIM_AD05   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 222         IOMUX_PADS(PAD_EIM_DA6__EIM_AD06   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 223         IOMUX_PADS(PAD_EIM_DA7__EIM_AD07   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 224         IOMUX_PADS(PAD_EIM_DA8__EIM_AD08   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 225         IOMUX_PADS(PAD_EIM_DA9__EIM_AD09   | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 226         IOMUX_PADS(PAD_EIM_DA10__EIM_AD10  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 227         IOMUX_PADS(PAD_EIM_DA11__EIM_AD11  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 228         IOMUX_PADS(PAD_EIM_DA12__EIM_AD12  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 229         IOMUX_PADS(PAD_EIM_DA13__EIM_AD13  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 230         IOMUX_PADS(PAD_EIM_DA14__EIM_AD14  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 231         IOMUX_PADS(PAD_EIM_DA15__EIM_AD15  | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 232         IOMUX_PADS(PAD_EIM_A16__EIM_ADDR16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 233         IOMUX_PADS(PAD_EIM_A17__EIM_ADDR17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 234         IOMUX_PADS(PAD_EIM_A18__EIM_ADDR18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 235         IOMUX_PADS(PAD_EIM_A19__EIM_ADDR19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 236         IOMUX_PADS(PAD_EIM_A20__EIM_ADDR20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 237         IOMUX_PADS(PAD_EIM_A21__EIM_ADDR21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 238         IOMUX_PADS(PAD_EIM_A22__EIM_ADDR22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 239         IOMUX_PADS(PAD_EIM_A23__EIM_ADDR23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 240         IOMUX_PADS(PAD_EIM_A24__EIM_ADDR24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 241         IOMUX_PADS(PAD_EIM_A25__EIM_ADDR25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
 242         IOMUX_PADS(PAD_EIM_OE__EIM_OE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
 243         IOMUX_PADS(PAD_EIM_RW__EIM_RW           | MUX_PAD_CTRL(NO_PAD_CTRL)),
 244         IOMUX_PADS(PAD_EIM_CS0__EIM_CS0_B       | MUX_PAD_CTRL(NO_PAD_CTRL)),
 245         IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01       | MUX_PAD_CTRL(NO_PAD_CTRL)),
 246 };
 247
 248 static void eimnor_cs_setup(void)
 249 {
 250         struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;
 251
 252
 253         /* NOR configuration */
 254         writel(0x00620181, &weim_regs->cs0gcr1);
 255         writel(0x00000001, &weim_regs->cs0gcr2);
 256         writel(0x0b020000, &weim_regs->cs0rcr1);
 257         writel(0x0000b000, &weim_regs->cs0rcr2);
 258         writel(0x0804a240, &weim_regs->cs0wcr1);
 259         writel(0x00000000, &weim_regs->cs0wcr2);
 260
 261         writel(0x00000120, &weim_regs->wcr);
 262         writel(0x00000010, &weim_regs->wiar);
 263         writel(0x00000000, &weim_regs->ear);
 264
 265         set_chipselect_size(CS0_128);
 266 }
 267
 268 static void setup_eimnor(void)
 269 {
 270         SETUP_IOMUX_PADS(eimnor_pads);
 271         gpio_direction_output(NOR_WP, 1);
 272
 273         enable_eim_clk(1);
 274         eimnor_cs_setup();
 275 }
 276
 277 /* mccmon6 board has SPI Flash is connected to SPI3 */
 278 int board_spi_cs_gpio(unsigned bus, unsigned cs)
 279 {
 280         return (bus == 2 && cs == 0) ? ECSPI3_CS0 : -1;
 281 }
 282
 283 static iomux_v3_cfg_t const ecspi3_pads[] = {
 284         /* SPI3 */
 285         IOMUX_PADS(PAD_DISP0_DAT3__GPIO4_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 286         IOMUX_PADS(PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 287         IOMUX_PADS(PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 288         IOMUX_PADS(PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 289 };
 290
 291 void setup_spi(void)
 292 {
 293         SETUP_IOMUX_PADS(ecspi3_pads);
 294
 295         enable_spi_clk(true, 2);
 296
 297         /* set cs0 to high */
 298         gpio_direction_output(ECSPI3_CS0, 1);
 299
 300         /* set flwp to high */
 301         gpio_direction_output(ECSPI3_FLWP, 1);
 302 }
 303
 304 struct i2c_pads_info mx6q_i2c1_pad_info = {
 305         .scl = {
 306                 .i2c_mode = MX6Q_PAD_CSI0_DAT9__I2C1_SCL
 307                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 308                 .gpio_mode = MX6Q_PAD_CSI0_DAT9__GPIO5_IO27
 309                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 310                 .gp = IMX_GPIO_NR(5, 27)
 311         },
 312         .sda = {
 313                 .i2c_mode = MX6Q_PAD_CSI0_DAT8__I2C1_SDA
 314                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 315                 .gpio_mode = MX6Q_PAD_CSI0_DAT8__GPIO5_IO26
 316                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 317                 .gp = IMX_GPIO_NR(5, 26)
 318         }
 319 };
 320
 321 struct i2c_pads_info mx6q_i2c2_pad_info = {
 322         .scl = {
 323                 .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL
 324                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 325                 .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12
 326                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 327                 .gp = IMX_GPIO_NR(4, 12)
 328         },
 329         .sda = {
 330                 .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA
 331                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 332                 .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13
 333                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 334                 .gp = IMX_GPIO_NR(4, 13)
 335         }
 336 };
 337
 338 int board_eth_init(bd_t *bis)
 339 {
 340         setup_iomux_enet();
 341
 342         return cpu_eth_init(bis);
 343 }
 344
 345 int board_early_init_f(void)
 346 {
 347         setup_iomux_uart();
 348
 349         return 0;
 350 }
 351
 352 int board_init(void)
 353 {
 354         /* address of boot parameters */
 355         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 356
 357         gpio_direction_output(DISPLAY_EN, 1);
 358
 359         setup_eimnor();
 360         setup_spi();
 361
 362         setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c1_pad_info);
 363         setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c2_pad_info);
 364
 365         return 0;
 366 }
 367
 368 int board_late_init(void)
 369 {
 370         setenv("board_name", "mccmon6");
 371
 372         return 0;
 373 }
 374
 375 int checkboard(void)
 376 {
 377         puts("Board: MCCMON6\n");
 378
 379         return 0;
 380 }
 381
 382 int board_phy_config(struct phy_device *phydev)
 383 {
 384         /*
 385          * Default setting for GMII Clock Pad Skew Register 0x1EF:
 386          * MMD Address 0x2h, Register 0x8h
 387          *
 388          * GTX_CLK Pad Skew 0xF -> 0.9 nsec skew
 389          * RX_CLK Pad Skew 0xF -> 0.9 nsec skew
 390          *
 391          * Adjustment -> write 0x3FF:
 392          * GTX_CLK Pad Skew 0x1F -> 1.8 nsec skew
 393          * RX_CLK Pad Skew 0x1F -> 1.8 nsec skew
 394          *
 395          */
 396         ksz9031_phy_extended_write(phydev, 0x2,
 397                                    MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
 398                                    MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x3FF);
 399
 400         ksz9031_phy_extended_write(phydev, 0x02,
 401                                    MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
 402                                    MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x00FF);
 403
 404         ksz9031_phy_extended_write(phydev, 0x2,
 405                                    MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
 406                                    MII_KSZ9031_MOD_DATA_NO_POST_INC,
 407                                    0x3333);
 408
 409         ksz9031_phy_extended_write(phydev, 0x2,
 410                                    MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
 411                                    MII_KSZ9031_MOD_DATA_NO_POST_INC,
 412                                    0x2052);
 413
 414         if (phydev->drv->config)
 415                 phydev->drv->config(phydev);
 416
 417         return 0;
 418 }
 419
 420 #ifdef CONFIG_SPL_BOARD_INIT
 421 void spl_board_init(void)
 422 {
 423         setup_eimnor();
 424
 425         gpio_direction_output(DISPLAY_EN, 1);
 426 }
 427 #endif /* CONFIG_SPL_BOARD_INIT */
 428
 429 #ifdef CONFIG_SPL_BUILD
 430 void board_boot_order(u32 *spl_boot_list)
 431 {
 432         switch (spl_boot_device()) {
 433         case BOOT_DEVICE_MMC2:
 434         case BOOT_DEVICE_MMC1:
 435                 spl_boot_list[0] = BOOT_DEVICE_MMC2;
 436                 spl_boot_list[1] = BOOT_DEVICE_MMC1;
 437                 break;
 438
 439         case BOOT_DEVICE_NOR:
 440                 spl_boot_list[0] = BOOT_DEVICE_NOR;
 441                 break;
 442         }
 443 }
 444 #endif /* CONFIG_SPL_BUILD */
 445
 446 #ifdef CONFIG_SPL_OS_BOOT
 447 int spl_start_uboot(void)
 448 {
 449         char s[16];
 450         int ret;
 451         /*
 452          * We use BOOT_DEVICE_MMC1, but SD card is connected
 453          * to MMC2
 454          *
 455          * Correct "mapping" is delivered in board defined
 456          * board_boot_order() function.
 457          *
 458          * SD card boot is regarded as a "development" one,
 459          * hence we _always_ go through the u-boot.
 460          *
 461          */
 462         if (spl_boot_device() == BOOT_DEVICE_MMC1)
 463                 return 1;
 464
 465         /* break into full u-boot on 'c' */
 466         if (serial_tstc() && serial_getc() == 'c')
 467                 return 1;
 468
 469         env_init();
 470         ret = getenv_f("boot_os", s, sizeof(s));
 471         if ((ret != -1) && (strcmp(s, "no") == 0))
 472                 return 1;
 473
 474         /*
 475          * Check if SWUpdate recovery needs to be started
 476          *
 477          * recovery_status = NULL (not set - ret == -1) -> normal operation
 478          *
 479          * recovery_status = progress or
 480          * recovery_status = failed   or
 481          * recovery_status = <any value> -> start SWUpdate
 482          *
 483          */
 484         ret = getenv_f("recovery_status", s, sizeof(s));
 485         if (ret != -1)
 486                 return 1;
 487
 488         return 0;
 489 }
 490 #endif /* CONFIG_SPL_OS_BOOT */