board/ronetix/pm9263/pm9263.c

   1 /*
   2  * (C) Copyright 2007-2008
   3  * Stelian Pop <stelian.pop@leadtechdesign.com>
   4  * Lead Tech Design <www.leadtechdesign.com>
   5  * Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
   6  * Copyright (C) 2009 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
   7  *
   8  * See file CREDITS for list of people who contributed to this
   9  * project.
  10  *
  11  * This program is free software; you can redistribute it and/or
  12  * modify it under the terms of the GNU General Public License as
  13  * published by the Free Software Foundation; either version 2 of
  14  * the License, or (at your option) any later version.
  15  *
  16  * This program is distributed in the hope that it will be useful,
  17  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  18  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  19  * GNU General Public License for more details.
  20  *
  21  * You should have received a copy of the GNU General Public License
  22  * along with this program; if not, write to the Free Software
  23  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  24  * MA 02111-1307 USA
  25  */
  26
  27 #include <common.h>
  28 #include <asm/sizes.h>
  29 #include <asm/arch/at91sam9263.h>
  30 #include <asm/arch/at91sam9263_matrix.h>
  31 #include <asm/arch/at91sam9_smc.h>
  32 #include <asm/arch/at91_common.h>
  33 #include <asm/arch/at91_pmc.h>
  34 #include <asm/arch/at91_rstc.h>
  35 #include <asm/arch/clk.h>
  36 #include <asm/arch/gpio.h>
  37 #include <asm/arch/io.h>
  38 #include <asm/arch/hardware.h>
  39 #include <lcd.h>
  40 #include <atmel_lcdc.h>
  41 #include <dataflash.h>
  42 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
  43 #include <net.h>
  44 #endif
  45 #include <netdev.h>
  46
  47 DECLARE_GLOBAL_DATA_PTR;
  48
  49 /* ------------------------------------------------------------------------- */
  50 /*
  51  * Miscelaneous platform dependent initialisations
  52  */
  53
  54 #ifdef CONFIG_CMD_NAND
  55 static void pm9263_nand_hw_init(void)
  56 {
  57         unsigned long csa;
  58
  59         /* Enable CS3 */
  60         csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
  61         at91_sys_write(AT91_MATRIX_EBI0CSA,
  62                        csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
  63
  64         /* Configure SMC CS3 for NAND/SmartMedia */
  65         at91_sys_write(AT91_SMC_SETUP(3),
  66                        AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(1) |
  67                        AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(1));
  68         at91_sys_write(AT91_SMC_PULSE(3),
  69                        AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
  70                        AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
  71         at91_sys_write(AT91_SMC_CYCLE(3),
  72                        AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
  73         at91_sys_write(AT91_SMC_MODE(3),
  74                        AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
  75                        AT91_SMC_EXNWMODE_DISABLE |
  76 #ifdef CONFIG_SYS_NAND_DBW_16
  77                        AT91_SMC_DBW_16 |
  78 #else /* CONFIG_SYS_NAND_DBW_8 */
  79                        AT91_SMC_DBW_8 |
  80 #endif
  81                        AT91_SMC_TDF_(2));
  82
  83         /* Configure RDY/BSY */
  84         at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
  85
  86         /* Enable NandFlash */
  87         at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
  88 }
  89 #endif
  90
  91 #ifdef CONFIG_MACB
  92 static void pm9263_macb_hw_init(void)
  93 {
  94         /*
  95          * PB27 enables the 50MHz oscillator for Ethernet PHY
  96          * 1 - enable
  97          * 0 - disable
  98          */
  99         at91_set_gpio_output(AT91_PIN_PB27, 1);
 100         at91_set_gpio_value(AT91_PIN_PB27, 1); /* 1- enable, 0 - disable */
 101
 102         /* Enable clock */
 103         at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_EMAC);
 104
 105         /*
 106          * Disable pull-up on:
 107          *      RXDV (PC25) => PHY normal mode (not Test mode)
 108          *      ERX0 (PE25) => PHY ADDR0
 109          *      ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
 110          *
 111          * PHY has internal pull-down
 112          */
 113         writel(pin_to_mask(AT91_PIN_PC25),
 114                pin_to_controller(AT91_PIN_PC0) + PIO_PUDR);
 115         writel(pin_to_mask(AT91_PIN_PE25) |
 116                pin_to_mask(AT91_PIN_PE26),
 117                pin_to_controller(AT91_PIN_PE0) + PIO_PUDR);
 118
 119
 120         /* Re-enable pull-up */
 121         writel(pin_to_mask(AT91_PIN_PC25),
 122                pin_to_controller(AT91_PIN_PC0) + PIO_PUER);
 123         writel(pin_to_mask(AT91_PIN_PE25) |
 124                pin_to_mask(AT91_PIN_PE26),
 125                pin_to_controller(AT91_PIN_PE0) + PIO_PUER);
 126
 127         at91_macb_hw_init();
 128 }
 129 #endif
 130
 131 #ifdef CONFIG_LCD
 132 vidinfo_t panel_info = {
 133         vl_col:         240,
 134         vl_row:         320,
 135         vl_clk:         4965000,
 136         vl_sync:        ATMEL_LCDC_INVLINE_INVERTED |
 137                         ATMEL_LCDC_INVFRAME_INVERTED,
 138         vl_bpix:        3,
 139         vl_tft:         1,
 140         vl_hsync_len:   5,
 141         vl_left_margin: 1,
 142         vl_right_margin:33,
 143         vl_vsync_len:   1,
 144         vl_upper_margin:1,
 145         vl_lower_margin:0,
 146         mmio:           AT91SAM9263_LCDC_BASE,
 147 };
 148
 149 void lcd_enable(void)
 150 {
 151         at91_set_gpio_value(AT91_PIN_PA22, 1); /* power up */
 152 }
 153
 154 void lcd_disable(void)
 155 {
 156         at91_set_gpio_value(AT91_PIN_PA22, 0); /* power down */
 157 }
 158
 159 #ifdef CONFIG_LCD_IN_PSRAM
 160
 161 #define PSRAM_CRE_PIN   AT91_PIN_PB29
 162 #define PSRAM_CTRL_REG  (PHYS_PSRAM + PHYS_PSRAM_SIZE - 2)
 163
 164 /* Initialize the PSRAM memory */
 165 static int pm9263_lcd_hw_psram_init(void)
 166 {
 167         volatile uint16_t x;
 168         unsigned long csa;
 169
 170         /* Enable CS3  3.3v, no pull-ups */
 171         csa = at91_sys_read(AT91_MATRIX_EBI1CSA);
 172         at91_sys_write(AT91_MATRIX_EBI1CSA,
 173                        csa | AT91_MATRIX_EBI1_DBPUC |
 174                        AT91_MATRIX_EBI1_VDDIOMSEL_3_3V);
 175
 176         /* Configure SMC1 CS0 for PSRAM - 16-bit */
 177         at91_sys_write(AT91_SMC1_SETUP(0),
 178                        AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
 179                        AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
 180         at91_sys_write(AT91_SMC1_PULSE(0),
 181                        AT91_SMC_NWEPULSE_(7) | AT91_SMC_NCS_WRPULSE_(7) |
 182                        AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(7));
 183         at91_sys_write(AT91_SMC1_CYCLE(0),
 184                        AT91_SMC_NWECYCLE_(8) | AT91_SMC_NRDCYCLE_(8));
 185         at91_sys_write(AT91_SMC1_MODE(0),
 186                        AT91_SMC_DBW_16 |
 187                        AT91_SMC_PMEN |
 188                        AT91_SMC_PS_32);
 189
 190         /* setup PB29 as output */
 191         at91_set_gpio_output(PSRAM_CRE_PIN, 1);
 192
 193         at91_set_gpio_value(PSRAM_CRE_PIN, 0);  /* set PSRAM_CRE_PIN to '0' */
 194
 195         /* PSRAM: write BCR */
 196         x = readw(PSRAM_CTRL_REG);
 197         x = readw(PSRAM_CTRL_REG);
 198         writew(1, PSRAM_CTRL_REG);      /* 0 - RCR,1 - BCR */
 199         writew(0x9d4f, PSRAM_CTRL_REG); /* write the BCR */
 200
 201         /* write RCR of the PSRAM */
 202         x = readw(PSRAM_CTRL_REG);
 203         x = readw(PSRAM_CTRL_REG);
 204         writew(0, PSRAM_CTRL_REG);      /* 0 - RCR,1 - BCR */
 205         /* set RCR; 0x10-async mode,0x90-page mode */
 206         writew(0x90, PSRAM_CTRL_REG);
 207
 208         /*
 209          * test to see if the PSRAM is MT45W2M16A or MT45W2M16B
 210          * MT45W2M16B - CRE must be 0
 211          * MT45W2M16A - CRE must be 1
 212          */
 213         writew(0x1234, PHYS_PSRAM);
 214         writew(0x5678, PHYS_PSRAM + 2);
 215
 216         /* test if the chip is MT45W2M16B */
 217         if ((readw(PHYS_PSRAM) != 0x1234) || (readw(PHYS_PSRAM+2) != 0x5678)) {
 218                 /* try with CRE=1 (MT45W2M16A) */
 219                 at91_set_gpio_value(PSRAM_CRE_PIN, 1); /* set PSRAM_CRE_PIN to '1' */
 220
 221                 /* write RCR of the PSRAM */
 222                 x = readw(PSRAM_CTRL_REG);
 223                 x = readw(PSRAM_CTRL_REG);
 224                 writew(0, PSRAM_CTRL_REG);      /* 0 - RCR,1 - BCR */
 225                 /* set RCR;0x10-async mode,0x90-page mode */
 226                 writew(0x90, PSRAM_CTRL_REG);
 227
 228
 229                 writew(0x1234, PHYS_PSRAM);
 230                 writew(0x5678, PHYS_PSRAM+2);
 231                 if ((readw(PHYS_PSRAM) != 0x1234)
 232                    || (readw(PHYS_PSRAM + 2) != 0x5678))
 233                         return 1;
 234
 235         }
 236
 237         /* Bus matrix */
 238         at91_sys_write( AT91_MATRIX_PRAS5, AT91_MATRIX_M5PR );
 239         at91_sys_write( AT91_MATRIX_SCFG5, AT91_MATRIX_ARBT_FIXED_PRIORITY |
 240                                 (AT91_MATRIX_FIXED_DEFMSTR & (5 << 18)) |
 241                                 AT91_MATRIX_DEFMSTR_TYPE_FIXED |
 242                                 (AT91_MATRIX_SLOT_CYCLE & (0xFF << 0)));
 243
 244         return 0;
 245 }
 246 #endif
 247
 248 static void pm9263_lcd_hw_init(void)
 249 {
 250         at91_set_A_periph(AT91_PIN_PC0, 0);     /* LCDVSYNC */
 251         at91_set_A_periph(AT91_PIN_PC1, 0);     /* LCDHSYNC */
 252         at91_set_A_periph(AT91_PIN_PC2, 0);     /* LCDDOTCK */
 253         at91_set_A_periph(AT91_PIN_PC3, 0);     /* LCDDEN */
 254         at91_set_B_periph(AT91_PIN_PB9, 0);     /* LCDCC */
 255         at91_set_A_periph(AT91_PIN_PC6, 0);     /* LCDD2 */
 256         at91_set_A_periph(AT91_PIN_PC7, 0);     /* LCDD3 */
 257         at91_set_A_periph(AT91_PIN_PC8, 0);     /* LCDD4 */
 258         at91_set_A_periph(AT91_PIN_PC9, 0);     /* LCDD5 */
 259         at91_set_A_periph(AT91_PIN_PC10, 0);    /* LCDD6 */
 260         at91_set_A_periph(AT91_PIN_PC11, 0);    /* LCDD7 */
 261         at91_set_A_periph(AT91_PIN_PC14, 0);    /* LCDD10 */
 262         at91_set_A_periph(AT91_PIN_PC15, 0);    /* LCDD11 */
 263         at91_set_A_periph(AT91_PIN_PC16, 0);    /* LCDD12 */
 264         at91_set_B_periph(AT91_PIN_PC12, 0);    /* LCDD13 */
 265         at91_set_A_periph(AT91_PIN_PC18, 0);    /* LCDD14 */
 266         at91_set_A_periph(AT91_PIN_PC19, 0);    /* LCDD15 */
 267         at91_set_A_periph(AT91_PIN_PC22, 0);    /* LCDD18 */
 268         at91_set_A_periph(AT91_PIN_PC23, 0);    /* LCDD19 */
 269         at91_set_A_periph(AT91_PIN_PC24, 0);    /* LCDD20 */
 270         at91_set_B_periph(AT91_PIN_PC17, 0);    /* LCDD21 */
 271         at91_set_A_periph(AT91_PIN_PC26, 0);    /* LCDD22 */
 272         at91_set_A_periph(AT91_PIN_PC27, 0);    /* LCDD23 */
 273
 274         at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_LCDC);
 275
 276         /* Power Control */
 277         at91_set_gpio_output(AT91_PIN_PA22, 1);
 278         at91_set_gpio_value(AT91_PIN_PA22, 0);  /* power down */
 279
 280 #ifdef CONFIG_LCD_IN_PSRAM
 281         /* initialize te PSRAM */
 282         int stat = pm9263_lcd_hw_psram_init();
 283
 284         gd->fb_base = (stat == 0) ? PHYS_PSRAM : AT91SAM9263_SRAM0_BASE;
 285 #else
 286         gd->fb_base = AT91SAM9263_SRAM0_BASE;
 287 #endif
 288
 289 }
 290
 291 #ifdef CONFIG_LCD_INFO
 292 #include <nand.h>
 293 #include <version.h>
 294
 295 extern flash_info_t flash_info[];
 296
 297 void lcd_show_board_info(void)
 298 {
 299         ulong dram_size, nand_size, flash_size, dataflash_size;
 300         int i;
 301         char temp[32];
 302
 303         lcd_printf ("%s\n", U_BOOT_VERSION);
 304         lcd_printf ("(C) 2009 Ronetix GmbH\n");
 305         lcd_printf ("support@ronetix.at\n");
 306         lcd_printf ("%s CPU at %s MHz",
 307                 CONFIG_SYS_AT91_CPU_NAME,
 308                 strmhz(temp, get_cpu_clk_rate()));
 309
 310         dram_size = 0;
 311         for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
 312                 dram_size += gd->bd->bi_dram[i].size;
 313
 314         nand_size = 0;
 315         for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
 316                 nand_size += nand_info[i].size;
 317
 318         flash_size = 0;
 319         for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
 320                 flash_size += flash_info[i].size;
 321
 322         dataflash_size = 0;
 323         for (i = 0; i < CONFIG_SYS_MAX_DATAFLASH_BANKS; i++)
 324                 dataflash_size += (unsigned int) dataflash_info[i].Device.pages_number *
 325                                 dataflash_info[i].Device.pages_size;
 326
 327         lcd_printf ("%ld MB SDRAM, %ld MB NAND\n%ld MB NOR Flash\n"
 328                         "4 MB PSRAM, %ld MB DataFlash\n",
 329                 dram_size >> 20,
 330                 nand_size >> 20,
 331                 flash_size >> 20,
 332                 dataflash_size >> 20);
 333 }
 334 #endif /* CONFIG_LCD_INFO */
 335
 336 #endif /* CONFIG_LCD */
 337
 338 int board_init(void)
 339 {
 340         /* Enable Ctrlc */
 341         console_init_f();
 342
 343         at91_sys_write(AT91_PMC_PCER,
 344                                         (1 << AT91SAM9263_ID_PIOA) |
 345                                         (1 << AT91SAM9263_ID_PIOCDE) |
 346                                         (1 << AT91SAM9263_ID_PIOB));
 347
 348         /* arch number of AT91SAM9263EK-Board */
 349         gd->bd->bi_arch_number = MACH_TYPE_PM9263;
 350
 351         /* adress of boot parameters */
 352         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 353
 354         at91_serial_hw_init();
 355 #ifdef CONFIG_CMD_NAND
 356         pm9263_nand_hw_init();
 357 #endif
 358 #ifdef CONFIG_HAS_DATAFLASH
 359         at91_spi0_hw_init(1 << 0);
 360 #endif
 361 #ifdef CONFIG_MACB
 362         pm9263_macb_hw_init();
 363 #endif
 364 #ifdef CONFIG_USB_OHCI_NEW
 365         at91_uhp_hw_init();
 366 #endif
 367 #ifdef CONFIG_LCD
 368         pm9263_lcd_hw_init();
 369 #endif
 370         return 0;
 371 }
 372
 373 int dram_init(void)
 374 {
 375         gd->bd->bi_dram[0].start = PHYS_SDRAM;
 376         gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
 377         return 0;
 378 }
 379
 380 #ifdef CONFIG_RESET_PHY_R
 381 void reset_phy(void)
 382 {
 383 #ifdef CONFIG_MACB
 384         /*
 385          * Initialize ethernet HW addr prior to starting Linux,
 386          * needed for nfsroot
 387          */
 388         eth_init(gd->bd);
 389 #endif
 390 }
 391 #endif
 392
 393 int board_eth_init(bd_t *bis)
 394 {
 395         int rc = 0;
 396 #ifdef CONFIG_MACB
 397         rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x01);
 398 #endif
 399         return rc;
 400 }
 401
 402 #ifdef CONFIG_DISPLAY_BOARDINFO
 403 int checkboard (void)
 404 {
 405         char *ss;
 406
 407         printf ("Board : Ronetix PM9263\n");
 408
 409         switch (gd->fb_base) {
 410         case PHYS_PSRAM:
 411                 ss = "(PSRAM)";
 412                 break;
 413
 414         case AT91SAM9263_SRAM0_BASE:
 415                 ss = "(Internal SRAM)";
 416                 break;
 417
 418         default:
 419                 ss = "";
 420                 break;
 421         }
 422         printf("Video memory : 0x%08lX %s\n", gd->fb_base, ss );
 423
 424         printf ("\n");
 425         return 0;
 426 }
 427 #endif