doc/README.t1040-l2switch

   1 This file contains information for VSC9953, a Vitesse L2 Switch IP
   2 which is integrated in the T1040/T1020 Freescale SoCs.
   3
   4 About Device:
   5 =============
   6 VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
   7         -       8192 MAC addresses
   8         -       Static Address provisioning
   9         -       Dynamic learning of MAC addresses and aging
  10         -       4096 VLANs
  11         -       Independent and shared VLAN learning (IVL, SVL)
  12         -       Policing with storm control and MC/BC protection
  13         -       IPv4 and IPv6 multicast
  14         -       Jumbo frames (9.6 KB)
  15         -       Access Control List
  16         -       VLAN editing, translation and remarking
  17         -       RMON counters per port
  18
  19 Switch interfaces:
  20         -       8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
  21         -       2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
  22                 to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
  23
  24 Commands Overview:
  25 =============
  26 Commands supported
  27         - enable/disable a port or show its configuration (speed, duplexity, status, etc.)
  28         - port statistics
  29         - MAC learning
  30         - add/remove FDB entries
  31         - Port-based VLAN
  32         - Private/Shared VLAN learning
  33         - VLAN ingress filtering
  34         - Port LAG
  35
  36 Commands syntax
  37 ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration
  38 ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics
  39 ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port
  40 ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries;
  41                                                                                           if [vlan <vid>] is missing, VID 1 will be used
  42 ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port
  43 ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members)
  44 ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port
  45 ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag.
  46                                                                           Tag's VID could be the frame's classified VID or the PVID of the port
  47 ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private
  48 ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port
  49 ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port
  50
  51 => ethsw show
  52     Port   Status     Link    Speed   Duplex
  53        0  enabled     down       10     half
  54        1  enabled     down       10     half
  55        2  enabled     down       10     half
  56        3  enabled       up     1000     full
  57        4 disabled     down        -     half
  58        5 disabled     down        -     half
  59        6 disabled     down        -     half
  60        7 disabled     down        -     half
  61        8  enabled       up     2500     full
  62        9  enabled       up     2500     full
  63 =>