Cleanup for GCC-4.x

[people/ms/u-boot.git] / drivers / e1000.c

/**************************************************************************
Inter Pro 1000 for ppcboot/das-u-boot
Drivers are port from Intel's Linux driver e1000-4.3.15
and from Etherboot pro 1000 driver by mrakes at vivato dot net
tested on both gig copper and gig fiber boards
***************************************************************************/
/*******************************************************************************


  Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.

  This program is free software; you can redistribute it and/or modify it
  under the terms of the GNU General Public License as published by the Free
  Software Foundation; either version 2 of the License, or (at your option)
  any later version.

  This program is distributed in the hope that it will be useful, but WITHOUT
  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  more details.

  You should have received a copy of the GNU General Public License along with
  this program; if not, write to the Free Software Foundation, Inc., 59
  Temple Place - Suite 330, Boston, MA  02111-1307, USA.

  The full GNU General Public License is included in this distribution in the
  file called LICENSE.

  Contact Information:
  Linux NICS <linux.nics@intel.com>
  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497

*******************************************************************************/
/*
 *  Copyright (C) Archway Digital Solutions.
 *
 *  written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org>
 *  2/9/2002
 *
 *  Copyright (C) Linux Networx.
 *  Massive upgrade to work with the new intel gigabit NICs.
 *  <ebiederman at lnxi dot com>
 */

#include "e1000.h"

#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
        defined(CONFIG_E1000)

#define TOUT_LOOP   100000

#undef  virt_to_bus
#define virt_to_bus(x)  ((unsigned long)x)
#define bus_to_phys(devno, a)   pci_mem_to_phys(devno, a)
#define mdelay(n)       udelay((n)*1000)

#define E1000_DEFAULT_PBA    0x00000030

/* NIC specific static variables go here */

static char tx_pool[128 + 16];
static char rx_pool[128 + 16];
static char packet[2096];

static struct e1000_tx_desc *tx_base;
static struct e1000_rx_desc *rx_base;

static int tx_tail;
static int rx_tail, rx_last;

static struct pci_device_id supported[] = {
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82542},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_FIBER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_COPPER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_COPPER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_FIBER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_COPPER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_LOM},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_COPPER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_COPPER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_FIBER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER},
        {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM},
};

/* Function forward declarations */
static int e1000_setup_link(struct eth_device *nic);
static int e1000_setup_fiber_link(struct eth_device *nic);
static int e1000_setup_copper_link(struct eth_device *nic);
static int e1000_phy_setup_autoneg(struct e1000_hw *hw);
static void e1000_config_collision_dist(struct e1000_hw *hw);
static int e1000_config_mac_to_phy(struct e1000_hw *hw);
static int e1000_config_fc_after_link_up(struct e1000_hw *hw);
static int e1000_check_for_link(struct eth_device *nic);
static int e1000_wait_autoneg(struct e1000_hw *hw);
static void e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed,
                                       uint16_t * duplex);
static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
                              uint16_t * phy_data);
static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
                               uint16_t phy_data);
static void e1000_phy_hw_reset(struct e1000_hw *hw);
static int e1000_phy_reset(struct e1000_hw *hw);
static int e1000_detect_gig_phy(struct e1000_hw *hw);

#define E1000_WRITE_REG(a, reg, value) (writel((value), ((a)->hw_addr + E1000_##reg)))
#define E1000_READ_REG(a, reg) (readl((a)->hw_addr + E1000_##reg))
#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) (\
                        writel((value), ((a)->hw_addr + E1000_##reg + ((offset) << 2))))
#define E1000_READ_REG_ARRAY(a, reg, offset) ( \
        readl((a)->hw_addr + E1000_##reg + ((offset) << 2)))
#define E1000_WRITE_FLUSH(a) {uint32_t x; x = E1000_READ_REG(a, STATUS);}

#ifndef CONFIG_AP1000 /* remove for warnings */
/******************************************************************************
 * Raises the EEPROM's clock input.
 *
 * hw - Struct containing variables accessed by shared code
 * eecd - EECD's current value
 *****************************************************************************/
static void
e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t * eecd)
{
        /* Raise the clock input to the EEPROM (by setting the SK bit), and then
         * wait 50 microseconds.
         */
        *eecd = *eecd | E1000_EECD_SK;
        E1000_WRITE_REG(hw, EECD, *eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);
}

/******************************************************************************
 * Lowers the EEPROM's clock input.
 *
 * hw - Struct containing variables accessed by shared code
 * eecd - EECD's current value
 *****************************************************************************/
static void
e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t * eecd)
{
        /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
         * wait 50 microseconds.
         */
        *eecd = *eecd & ~E1000_EECD_SK;
        E1000_WRITE_REG(hw, EECD, *eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);
}

/******************************************************************************
 * Shift data bits out to the EEPROM.
 *
 * hw - Struct containing variables accessed by shared code
 * data - data to send to the EEPROM
 * count - number of bits to shift out
 *****************************************************************************/
static void
e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count)
{
        uint32_t eecd;
        uint32_t mask;

        /* We need to shift "count" bits out to the EEPROM. So, value in the
         * "data" parameter will be shifted out to the EEPROM one bit at a time.
         * In order to do this, "data" must be broken down into bits.
         */
        mask = 0x01 << (count - 1);
        eecd = E1000_READ_REG(hw, EECD);
        eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
        do {
                /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
                 * and then raising and then lowering the clock (the SK bit controls
                 * the clock input to the EEPROM).  A "0" is shifted out to the EEPROM
                 * by setting "DI" to "0" and then raising and then lowering the clock.
                 */
                eecd &= ~E1000_EECD_DI;

                if (data & mask)
                        eecd |= E1000_EECD_DI;

                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);

                udelay(50);

                e1000_raise_ee_clk(hw, &eecd);
                e1000_lower_ee_clk(hw, &eecd);

                mask = mask >> 1;

        } while (mask);

        /* We leave the "DI" bit set to "0" when we leave this routine. */
        eecd &= ~E1000_EECD_DI;
        E1000_WRITE_REG(hw, EECD, eecd);
}

/******************************************************************************
 * Shift data bits in from the EEPROM
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static uint16_t
e1000_shift_in_ee_bits(struct e1000_hw *hw)
{
        uint32_t eecd;
        uint32_t i;
        uint16_t data;

        /* In order to read a register from the EEPROM, we need to shift 16 bits
         * in from the EEPROM. Bits are "shifted in" by raising the clock input to
         * the EEPROM (setting the SK bit), and then reading the value of the "DO"
         * bit.  During this "shifting in" process the "DI" bit should always be
         * clear..
         */

        eecd = E1000_READ_REG(hw, EECD);

        eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
        data = 0;

        for (i = 0; i < 16; i++) {
                data = data << 1;
                e1000_raise_ee_clk(hw, &eecd);

                eecd = E1000_READ_REG(hw, EECD);

                eecd &= ~(E1000_EECD_DI);
                if (eecd & E1000_EECD_DO)
                        data |= 1;

                e1000_lower_ee_clk(hw, &eecd);
        }

        return data;
}

/******************************************************************************
 * Prepares EEPROM for access
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
 * function should be called before issuing a command to the EEPROM.
 *****************************************************************************/
static void
e1000_setup_eeprom(struct e1000_hw *hw)
{
        uint32_t eecd;

        eecd = E1000_READ_REG(hw, EECD);

        /* Clear SK and DI */
        eecd &= ~(E1000_EECD_SK | E1000_EECD_DI);
        E1000_WRITE_REG(hw, EECD, eecd);

        /* Set CS */
        eecd |= E1000_EECD_CS;
        E1000_WRITE_REG(hw, EECD, eecd);
}

/******************************************************************************
 * Returns EEPROM to a "standby" state
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
e1000_standby_eeprom(struct e1000_hw *hw)
{
        uint32_t eecd;

        eecd = E1000_READ_REG(hw, EECD);

        /* Deselct EEPROM */
        eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
        E1000_WRITE_REG(hw, EECD, eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);

        /* Clock high */
        eecd |= E1000_EECD_SK;
        E1000_WRITE_REG(hw, EECD, eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);

        /* Select EEPROM */
        eecd |= E1000_EECD_CS;
        E1000_WRITE_REG(hw, EECD, eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);

        /* Clock low */
        eecd &= ~E1000_EECD_SK;
        E1000_WRITE_REG(hw, EECD, eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);
}

/******************************************************************************
 * Reads a 16 bit word from the EEPROM.
 *
 * hw - Struct containing variables accessed by shared code
 * offset - offset of  word in the EEPROM to read
 * data - word read from the EEPROM
 *****************************************************************************/
static int
e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, uint16_t * data)
{
        uint32_t eecd;
        uint32_t i = 0;
        int large_eeprom = FALSE;

        /* Request EEPROM Access */
        if (hw->mac_type > e1000_82544) {
                eecd = E1000_READ_REG(hw, EECD);
                if (eecd & E1000_EECD_SIZE)
                        large_eeprom = TRUE;
                eecd |= E1000_EECD_REQ;
                E1000_WRITE_REG(hw, EECD, eecd);
                eecd = E1000_READ_REG(hw, EECD);
                while ((!(eecd & E1000_EECD_GNT)) && (i < 100)) {
                        i++;
                        udelay(10);
                        eecd = E1000_READ_REG(hw, EECD);
                }
                if (!(eecd & E1000_EECD_GNT)) {
                        eecd &= ~E1000_EECD_REQ;
                        E1000_WRITE_REG(hw, EECD, eecd);
                        DEBUGOUT("Could not acquire EEPROM grant\n");
                        return -E1000_ERR_EEPROM;
                }
        }

        /*  Prepare the EEPROM for reading  */
        e1000_setup_eeprom(hw);

        /*  Send the READ command (opcode + addr)  */
        e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE, 3);
        e1000_shift_out_ee_bits(hw, offset, (large_eeprom) ? 8 : 6);

        /* Read the data */
        *data = e1000_shift_in_ee_bits(hw);

        /* End this read operation */
        e1000_standby_eeprom(hw);

        /* Stop requesting EEPROM access */
        if (hw->mac_type > e1000_82544) {
                eecd = E1000_READ_REG(hw, EECD);
                eecd &= ~E1000_EECD_REQ;
                E1000_WRITE_REG(hw, EECD, eecd);
        }

        return 0;
}

#if 0
static void
e1000_eeprom_cleanup(struct e1000_hw *hw)
{
        uint32_t eecd;

        eecd = E1000_READ_REG(hw, EECD);
        eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
        E1000_WRITE_REG(hw, EECD, eecd);
        e1000_raise_ee_clk(hw, &eecd);
        e1000_lower_ee_clk(hw, &eecd);
}

static uint16_t
e1000_wait_eeprom_done(struct e1000_hw *hw)
{
        uint32_t eecd;
        uint32_t i;

        e1000_standby_eeprom(hw);
        for (i = 0; i < 200; i++) {
                eecd = E1000_READ_REG(hw, EECD);
                if (eecd & E1000_EECD_DO)
                        return (TRUE);
                udelay(5);
        }
        return (FALSE);
}

static int
e1000_write_eeprom(struct e1000_hw *hw, uint16_t Reg, uint16_t Data)
{
        uint32_t eecd;
        int large_eeprom = FALSE;
        int i = 0;

        /* Request EEPROM Access */
        if (hw->mac_type > e1000_82544) {
                eecd = E1000_READ_REG(hw, EECD);
                if (eecd & E1000_EECD_SIZE)
                        large_eeprom = TRUE;
                eecd |= E1000_EECD_REQ;
                E1000_WRITE_REG(hw, EECD, eecd);
                eecd = E1000_READ_REG(hw, EECD);
                while ((!(eecd & E1000_EECD_GNT)) && (i < 100)) {
                        i++;
                        udelay(5);
                        eecd = E1000_READ_REG(hw, EECD);
                }
                if (!(eecd & E1000_EECD_GNT)) {
                        eecd &= ~E1000_EECD_REQ;
                        E1000_WRITE_REG(hw, EECD, eecd);
                        DEBUGOUT("Could not acquire EEPROM grant\n");
                        return FALSE;
                }
        }
        e1000_setup_eeprom(hw);
        e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE, 5);
        e1000_shift_out_ee_bits(hw, Reg, (large_eeprom) ? 6 : 4);
        e1000_standby_eeprom(hw);
        e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE, 3);
        e1000_shift_out_ee_bits(hw, Reg, (large_eeprom) ? 8 : 6);
        e1000_shift_out_ee_bits(hw, Data, 16);
        if (!e1000_wait_eeprom_done(hw)) {
                return FALSE;
        }
        e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE, 5);
        e1000_shift_out_ee_bits(hw, Reg, (large_eeprom) ? 6 : 4);
        e1000_eeprom_cleanup(hw);

        /* Stop requesting EEPROM access */
        if (hw->mac_type > e1000_82544) {
                eecd = E1000_READ_REG(hw, EECD);
                eecd &= ~E1000_EECD_REQ;
                E1000_WRITE_REG(hw, EECD, eecd);
        }
        i = 0;
        eecd = E1000_READ_REG(hw, EECD);
        while (((eecd & E1000_EECD_GNT)) && (i < 500)) {
                i++;
                udelay(10);
                eecd = E1000_READ_REG(hw, EECD);
        }
        if ((eecd & E1000_EECD_GNT)) {
                DEBUGOUT("Could not release EEPROM grant\n");
        }
        return TRUE;
}
#endif

/******************************************************************************
 * Verifies that the EEPROM has a valid checksum
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Reads the first 64 16 bit words of the EEPROM and sums the values read.
 * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
 * valid.
 *****************************************************************************/
static int
e1000_validate_eeprom_checksum(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint16_t checksum = 0;
        uint16_t i, eeprom_data;

        DEBUGFUNC();

        for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
                if (e1000_read_eeprom(hw, i, &eeprom_data) < 0) {
                        DEBUGOUT("EEPROM Read Error\n");
                        return -E1000_ERR_EEPROM;
                }
                checksum += eeprom_data;
        }

        if (checksum == (uint16_t) EEPROM_SUM) {
                return 0;
        } else {
                DEBUGOUT("EEPROM Checksum Invalid\n");
                return -E1000_ERR_EEPROM;
        }
}
#endif /* #ifndef CONFIG_AP1000 */

/******************************************************************************
 * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
 * second function of dual function devices
 *
 * nic - Struct containing variables accessed by shared code
 *****************************************************************************/
static int
e1000_read_mac_addr(struct eth_device *nic)
{
#ifndef CONFIG_AP1000
        struct e1000_hw *hw = nic->priv;
        uint16_t offset;
        uint16_t eeprom_data;
        int i;

        DEBUGFUNC();

        for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
                offset = i >> 1;
                if (e1000_read_eeprom(hw, offset, &eeprom_data) < 0) {
                        DEBUGOUT("EEPROM Read Error\n");
                        return -E1000_ERR_EEPROM;
                }
                nic->enetaddr[i] = eeprom_data & 0xff;
                nic->enetaddr[i + 1] = (eeprom_data >> 8) & 0xff;
        }
        if ((hw->mac_type == e1000_82546) &&
            (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
                /* Invert the last bit if this is the second device */
                nic->enetaddr[5] += 1;
        }
#else
        /*
         * The AP1000's e1000 has no eeprom; the MAC address is stored in the
         * environment variables.  Currently this does not support the addition
         * of a PMC e1000 card, which is certainly a possibility, so this should
         * be updated to properly use the env variable only for the onboard e1000
         */

        int ii;
        char *s, *e;

        DEBUGFUNC();

        s = getenv ("ethaddr");
        if (s == NULL){
                return -E1000_ERR_EEPROM;
        }
        else{
                for(ii = 0; ii < 6; ii++) {
                        nic->enetaddr[ii] = s ? simple_strtoul (s, &e, 16) : 0;
                        if (s){
                                s = (*e) ? e + 1 : e;
                        }
                }
        }
#endif
        return 0;
}

/******************************************************************************
 * Initializes receive address filters.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Places the MAC address in receive address register 0 and clears the rest
 * of the receive addresss registers. Clears the multicast table. Assumes
 * the receiver is in reset when the routine is called.
 *****************************************************************************/
static void
e1000_init_rx_addrs(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint32_t i;
        uint32_t addr_low;
        uint32_t addr_high;

        DEBUGFUNC();

        /* Setup the receive address. */
        DEBUGOUT("Programming MAC Address into RAR[0]\n");
        addr_low = (nic->enetaddr[0] |
                    (nic->enetaddr[1] << 8) |
                    (nic->enetaddr[2] << 16) | (nic->enetaddr[3] << 24));

        addr_high = (nic->enetaddr[4] | (nic->enetaddr[5] << 8) | E1000_RAH_AV);

        E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low);
        E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high);

        /* Zero out the other 15 receive addresses. */
        DEBUGOUT("Clearing RAR[1-15]\n");
        for (i = 1; i < E1000_RAR_ENTRIES; i++) {
                E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
                E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
        }
}

/******************************************************************************
 * Clears the VLAN filer table
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
e1000_clear_vfta(struct e1000_hw *hw)
{
        uint32_t offset;

        for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++)
                E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
}

/******************************************************************************
 * Set the mac type member in the hw struct.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static int
e1000_set_mac_type(struct e1000_hw *hw)
{
        DEBUGFUNC();

        switch (hw->device_id) {
        case E1000_DEV_ID_82542:
                switch (hw->revision_id) {
                case E1000_82542_2_0_REV_ID:
                        hw->mac_type = e1000_82542_rev2_0;
                        break;
                case E1000_82542_2_1_REV_ID:
                        hw->mac_type = e1000_82542_rev2_1;
                        break;
                default:
                        /* Invalid 82542 revision ID */
                        return -E1000_ERR_MAC_TYPE;
                }
                break;
        case E1000_DEV_ID_82543GC_FIBER:
        case E1000_DEV_ID_82543GC_COPPER:
                hw->mac_type = e1000_82543;
                break;
        case E1000_DEV_ID_82544EI_COPPER:
        case E1000_DEV_ID_82544EI_FIBER:
        case E1000_DEV_ID_82544GC_COPPER:
        case E1000_DEV_ID_82544GC_LOM:
                hw->mac_type = e1000_82544;
                break;
        case E1000_DEV_ID_82540EM:
        case E1000_DEV_ID_82540EM_LOM:
                hw->mac_type = e1000_82540;
                break;
        case E1000_DEV_ID_82545EM_COPPER:
        case E1000_DEV_ID_82545EM_FIBER:
                hw->mac_type = e1000_82545;
                break;
        case E1000_DEV_ID_82546EB_COPPER:
        case E1000_DEV_ID_82546EB_FIBER:
                hw->mac_type = e1000_82546;
                break;
        default:
                /* Should never have loaded on this device */
                return -E1000_ERR_MAC_TYPE;
        }
        return E1000_SUCCESS;
}

/******************************************************************************
 * Reset the transmit and receive units; mask and clear all interrupts.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
void
e1000_reset_hw(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint32_t ctrl_ext;
        uint32_t icr;
        uint32_t manc;

        DEBUGFUNC();

        /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
        if (hw->mac_type == e1000_82542_rev2_0) {
                DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
                pci_write_config_word(hw->pdev, PCI_COMMAND,
                                      hw->
                                      pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
        }

        /* Clear interrupt mask to stop board from generating interrupts */
        DEBUGOUT("Masking off all interrupts\n");
        E1000_WRITE_REG(hw, IMC, 0xffffffff);

        /* Disable the Transmit and Receive units.  Then delay to allow
         * any pending transactions to complete before we hit the MAC with
         * the global reset.
         */
        E1000_WRITE_REG(hw, RCTL, 0);
        E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP);
        E1000_WRITE_FLUSH(hw);

        /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
        hw->tbi_compatibility_on = FALSE;

        /* Delay to allow any outstanding PCI transactions to complete before
         * resetting the device
         */
        mdelay(10);

        /* Issue a global reset to the MAC.  This will reset the chip's
         * transmit, receive, DMA, and link units.  It will not effect
         * the current PCI configuration.  The global reset bit is self-
         * clearing, and should clear within a microsecond.
         */
        DEBUGOUT("Issuing a global reset to MAC\n");
        ctrl = E1000_READ_REG(hw, CTRL);

#if 0
        if (hw->mac_type > e1000_82543)
                E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
        else
#endif
                E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));

        /* Force a reload from the EEPROM if necessary */
        if (hw->mac_type < e1000_82540) {
                /* Wait for reset to complete */
                udelay(10);
                ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
                ctrl_ext |= E1000_CTRL_EXT_EE_RST;
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
                E1000_WRITE_FLUSH(hw);
                /* Wait for EEPROM reload */
                mdelay(2);
        } else {
                /* Wait for EEPROM reload (it happens automatically) */
                mdelay(4);
                /* Dissable HW ARPs on ASF enabled adapters */
                manc = E1000_READ_REG(hw, MANC);
                manc &= ~(E1000_MANC_ARP_EN);
                E1000_WRITE_REG(hw, MANC, manc);
        }

        /* Clear interrupt mask to stop board from generating interrupts */
        DEBUGOUT("Masking off all interrupts\n");
        E1000_WRITE_REG(hw, IMC, 0xffffffff);

        /* Clear any pending interrupt events. */
        icr = E1000_READ_REG(hw, ICR);

        /* If MWI was previously enabled, reenable it. */
        if (hw->mac_type == e1000_82542_rev2_0) {
                pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
        }
}

/******************************************************************************
 * Performs basic configuration of the adapter.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Assumes that the controller has previously been reset and is in a
 * post-reset uninitialized state. Initializes the receive address registers,
 * multicast table, and VLAN filter table. Calls routines to setup link
 * configuration and flow control settings. Clears all on-chip counters. Leaves
 * the transmit and receive units disabled and uninitialized.
 *****************************************************************************/
static int
e1000_init_hw(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint32_t ctrl, status;
        uint32_t i;
        int32_t ret_val;
        uint16_t pcix_cmd_word;
        uint16_t pcix_stat_hi_word;
        uint16_t cmd_mmrbc;
        uint16_t stat_mmrbc;
        e1000_bus_type bus_type = e1000_bus_type_unknown;

        DEBUGFUNC();
#if 0
        /* Initialize Identification LED */
        ret_val = e1000_id_led_init(hw);
        if (ret_val < 0) {
                DEBUGOUT("Error Initializing Identification LED\n");
                return ret_val;
        }
#endif
        /* Set the Media Type and exit with error if it is not valid. */
        if (hw->mac_type != e1000_82543) {
                /* tbi_compatibility is only valid on 82543 */
                hw->tbi_compatibility_en = FALSE;
        }

        if (hw->mac_type >= e1000_82543) {
                status = E1000_READ_REG(hw, STATUS);
                if (status & E1000_STATUS_TBIMODE) {
                        hw->media_type = e1000_media_type_fiber;
                        /* tbi_compatibility not valid on fiber */
                        hw->tbi_compatibility_en = FALSE;
                } else {
                        hw->media_type = e1000_media_type_copper;
                }
        } else {
                /* This is an 82542 (fiber only) */
                hw->media_type = e1000_media_type_fiber;
        }

        /* Disabling VLAN filtering. */
        DEBUGOUT("Initializing the IEEE VLAN\n");
        E1000_WRITE_REG(hw, VET, 0);

        e1000_clear_vfta(hw);

        /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
        if (hw->mac_type == e1000_82542_rev2_0) {
                DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
                pci_write_config_word(hw->pdev, PCI_COMMAND,
                                      hw->
                                      pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
                E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
                E1000_WRITE_FLUSH(hw);
                mdelay(5);
        }

        /* Setup the receive address. This involves initializing all of the Receive
         * Address Registers (RARs 0 - 15).
         */
        e1000_init_rx_addrs(nic);

        /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
        if (hw->mac_type == e1000_82542_rev2_0) {
                E1000_WRITE_REG(hw, RCTL, 0);
                E1000_WRITE_FLUSH(hw);
                mdelay(1);
                pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
        }

        /* Zero out the Multicast HASH table */
        DEBUGOUT("Zeroing the MTA\n");
        for (i = 0; i < E1000_MC_TBL_SIZE; i++)
                E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);

#if 0
        /* Set the PCI priority bit correctly in the CTRL register.  This
         * determines if the adapter gives priority to receives, or if it
         * gives equal priority to transmits and receives.
         */
        if (hw->dma_fairness) {
                ctrl = E1000_READ_REG(hw, CTRL);
                E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
        }
#endif
        if (hw->mac_type >= e1000_82543) {
                status = E1000_READ_REG(hw, STATUS);
                bus_type = (status & E1000_STATUS_PCIX_MODE) ?
                    e1000_bus_type_pcix : e1000_bus_type_pci;
        }
        /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
        if (bus_type == e1000_bus_type_pcix) {
                pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
                                     &pcix_cmd_word);
                pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI,
                                     &pcix_stat_hi_word);
                cmd_mmrbc =
                    (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
                    PCIX_COMMAND_MMRBC_SHIFT;
                stat_mmrbc =
                    (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
                    PCIX_STATUS_HI_MMRBC_SHIFT;
                if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
                        stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K;
                if (cmd_mmrbc > stat_mmrbc) {
                        pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
                        pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
                        pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
                                              pcix_cmd_word);
                }
        }

        /* Call a subroutine to configure the link and setup flow control. */
        ret_val = e1000_setup_link(nic);

        /* Set the transmit descriptor write-back policy */
        if (hw->mac_type > e1000_82544) {
                ctrl = E1000_READ_REG(hw, TXDCTL);
                ctrl =
                    (ctrl & ~E1000_TXDCTL_WTHRESH) |
                    E1000_TXDCTL_FULL_TX_DESC_WB;
                E1000_WRITE_REG(hw, TXDCTL, ctrl);
        }
#if 0
        /* Clear all of the statistics registers (clear on read).  It is
         * important that we do this after we have tried to establish link
         * because the symbol error count will increment wildly if there
         * is no link.
         */
        e1000_clear_hw_cntrs(hw);
#endif

        return ret_val;
}

/******************************************************************************
 * Configures flow control and link settings.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Determines which flow control settings to use. Calls the apropriate media-
 * specific link configuration function. Configures the flow control settings.
 * Assuming the adapter has a valid link partner, a valid link should be
 * established. Assumes the hardware has previously been reset and the
 * transmitter and receiver are not enabled.
 *****************************************************************************/
static int
e1000_setup_link(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint32_t ctrl_ext;
        int32_t ret_val;
        uint16_t eeprom_data;

        DEBUGFUNC();

#ifndef CONFIG_AP1000
        /* Read and store word 0x0F of the EEPROM. This word contains bits
         * that determine the hardware's default PAUSE (flow control) mode,
         * a bit that determines whether the HW defaults to enabling or
         * disabling auto-negotiation, and the direction of the
         * SW defined pins. If there is no SW over-ride of the flow
         * control setting, then the variable hw->fc will
         * be initialized based on a value in the EEPROM.
         */
        if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, &eeprom_data) < 0) {
                DEBUGOUT("EEPROM Read Error\n");
                return -E1000_ERR_EEPROM;
        }
#else
        /* we have to hardcode the proper value for our hardware. */
        /* this value is for the 82540EM pci card used for prototyping, and it works. */
        eeprom_data = 0xb220;
#endif

        if (hw->fc == e1000_fc_default) {
                if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
                        hw->fc = e1000_fc_none;
                else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
                         EEPROM_WORD0F_ASM_DIR)
                        hw->fc = e1000_fc_tx_pause;
                else
                        hw->fc = e1000_fc_full;
        }

        /* We want to save off the original Flow Control configuration just
         * in case we get disconnected and then reconnected into a different
         * hub or switch with different Flow Control capabilities.
         */
        if (hw->mac_type == e1000_82542_rev2_0)
                hw->fc &= (~e1000_fc_tx_pause);

        if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
                hw->fc &= (~e1000_fc_rx_pause);

        hw->original_fc = hw->fc;

        DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc);

        /* Take the 4 bits from EEPROM word 0x0F that determine the initial
         * polarity value for the SW controlled pins, and setup the
         * Extended Device Control reg with that info.
         * This is needed because one of the SW controlled pins is used for
         * signal detection.  So this should be done before e1000_setup_pcs_link()
         * or e1000_phy_setup() is called.
         */
        if (hw->mac_type == e1000_82543) {
                ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
                            SWDPIO__EXT_SHIFT);
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
        }

        /* Call the necessary subroutine to configure the link. */
        ret_val = (hw->media_type == e1000_media_type_fiber) ?
            e1000_setup_fiber_link(nic) : e1000_setup_copper_link(nic);
        if (ret_val < 0) {
                return ret_val;
        }

        /* Initialize the flow control address, type, and PAUSE timer
         * registers to their default values.  This is done even if flow
         * control is disabled, because it does not hurt anything to
         * initialize these registers.
         */
        DEBUGOUT
            ("Initializing the Flow Control address, type and timer regs\n");

        E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
        E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
        E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
        E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);

        /* Set the flow control receive threshold registers.  Normally,
         * these registers will be set to a default threshold that may be
         * adjusted later by the driver's runtime code.  However, if the
         * ability to transmit pause frames in not enabled, then these
         * registers will be set to 0.
         */
        if (!(hw->fc & e1000_fc_tx_pause)) {
                E1000_WRITE_REG(hw, FCRTL, 0);
                E1000_WRITE_REG(hw, FCRTH, 0);
        } else {
                /* We need to set up the Receive Threshold high and low water marks
                 * as well as (optionally) enabling the transmission of XON frames.
                 */
                if (hw->fc_send_xon) {
                        E1000_WRITE_REG(hw, FCRTL,
                                        (hw->fc_low_water | E1000_FCRTL_XONE));
                        E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
                } else {
                        E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water);
                        E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
                }
        }
        return ret_val;
}

/******************************************************************************
 * Sets up link for a fiber based adapter
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Manipulates Physical Coding Sublayer functions in order to configure
 * link. Assumes the hardware has been previously reset and the transmitter
 * and receiver are not enabled.
 *****************************************************************************/
static int
e1000_setup_fiber_link(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint32_t ctrl;
        uint32_t status;
        uint32_t txcw = 0;
        uint32_t i;
        uint32_t signal;
        int32_t ret_val;

        DEBUGFUNC();
        /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
         * set when the optics detect a signal. On older adapters, it will be
         * cleared when there is a signal
         */
        ctrl = E1000_READ_REG(hw, CTRL);
        if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS))
                signal = E1000_CTRL_SWDPIN1;
        else
                signal = 0;

        printf("signal for %s is %x (ctrl %08x)!!!!\n", nic->name, signal,
               ctrl);
        /* Take the link out of reset */
        ctrl &= ~(E1000_CTRL_LRST);

        e1000_config_collision_dist(hw);

        /* Check for a software override of the flow control settings, and setup
         * the device accordingly.  If auto-negotiation is enabled, then software
         * will have to set the "PAUSE" bits to the correct value in the Tranmsit
         * Config Word Register (TXCW) and re-start auto-negotiation.  However, if
         * auto-negotiation is disabled, then software will have to manually
         * configure the two flow control enable bits in the CTRL register.
         *
         * The possible values of the "fc" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause frames, but
         *          not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames but we do
         *          not support receiving pause frames).
         *      3:  Both Rx and TX flow control (symmetric) are enabled.
         */
        switch (hw->fc) {
        case e1000_fc_none:
                /* Flow control is completely disabled by a software over-ride. */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
                break;
        case e1000_fc_rx_pause:
                /* RX Flow control is enabled and TX Flow control is disabled by a
                 * software over-ride. Since there really isn't a way to advertise
                 * that we are capable of RX Pause ONLY, we will advertise that we
                 * support both symmetric and asymmetric RX PAUSE. Later, we will
                 *  disable the adapter's ability to send PAUSE frames.
                 */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
                break;
        case e1000_fc_tx_pause:
                /* TX Flow control is enabled, and RX Flow control is disabled, by a
                 * software over-ride.
                 */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
                break;
        case e1000_fc_full:
                /* Flow control (both RX and TX) is enabled by a software over-ride. */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
                break;
        default:
                DEBUGOUT("Flow control param set incorrectly\n");
                return -E1000_ERR_CONFIG;
                break;
        }

        /* Since auto-negotiation is enabled, take the link out of reset (the link
         * will be in reset, because we previously reset the chip). This will
         * restart auto-negotiation.  If auto-neogtiation is successful then the
         * link-up status bit will be set and the flow control enable bits (RFCE
         * and TFCE) will be set according to their negotiated value.
         */
        DEBUGOUT("Auto-negotiation enabled (%#x)\n", txcw);

        E1000_WRITE_REG(hw, TXCW, txcw);
        E1000_WRITE_REG(hw, CTRL, ctrl);
        E1000_WRITE_FLUSH(hw);

        hw->txcw = txcw;
        mdelay(1);

        /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
         * indication in the Device Status Register.  Time-out if a link isn't
         * seen in 500 milliseconds seconds (Auto-negotiation should complete in
         * less than 500 milliseconds even if the other end is doing it in SW).
         */
        if ((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) {
                DEBUGOUT("Looking for Link\n");
                for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
                        mdelay(10);
                        status = E1000_READ_REG(hw, STATUS);
                        if (status & E1000_STATUS_LU)
                                break;
                }
                if (i == (LINK_UP_TIMEOUT / 10)) {
                        /* AutoNeg failed to achieve a link, so we'll call
                         * e1000_check_for_link. This routine will force the link up if we
                         * detect a signal. This will allow us to communicate with
                         * non-autonegotiating link partners.
                         */
                        DEBUGOUT("Never got a valid link from auto-neg!!!\n");
                        hw->autoneg_failed = 1;
                        ret_val = e1000_check_for_link(nic);
                        if (ret_val < 0) {
                                DEBUGOUT("Error while checking for link\n");
                                return ret_val;
                        }
                        hw->autoneg_failed = 0;
                } else {
                        hw->autoneg_failed = 0;
                        DEBUGOUT("Valid Link Found\n");
                }
        } else {
                DEBUGOUT("No Signal Detected\n");
                return -E1000_ERR_NOLINK;
        }
        return 0;
}

/******************************************************************************
* Detects which PHY is present and the speed and duplex
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int
e1000_setup_copper_link(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint32_t ctrl;
        int32_t ret_val;
        uint16_t i;
        uint16_t phy_data;

        DEBUGFUNC();

        ctrl = E1000_READ_REG(hw, CTRL);
        /* With 82543, we need to force speed and duplex on the MAC equal to what
         * the PHY speed and duplex configuration is. In addition, we need to
         * perform a hardware reset on the PHY to take it out of reset.
         */
        if (hw->mac_type > e1000_82543) {
                ctrl |= E1000_CTRL_SLU;
                ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
                E1000_WRITE_REG(hw, CTRL, ctrl);
        } else {
                ctrl |=
                    (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
                E1000_WRITE_REG(hw, CTRL, ctrl);
                e1000_phy_hw_reset(hw);
        }

        /* Make sure we have a valid PHY */
        ret_val = e1000_detect_gig_phy(hw);
        if (ret_val < 0) {
                DEBUGOUT("Error, did not detect valid phy.\n");
                return ret_val;
        }
        DEBUGOUT("Phy ID = %x \n", hw->phy_id);

        /* Enable CRS on TX. This must be set for half-duplex operation. */
        if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;

#if 0
        /* Options:
         *   MDI/MDI-X = 0 (default)
         *   0 - Auto for all speeds
         *   1 - MDI mode
         *   2 - MDI-X mode
         *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
         */
        phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
        switch (hw->mdix) {
        case 1:
                phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
                break;
        case 2:
                phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
                break;
        case 3:
                phy_data |= M88E1000_PSCR_AUTO_X_1000T;
                break;
        case 0:
        default:
                phy_data |= M88E1000_PSCR_AUTO_X_MODE;
                break;
        }
#else
        phy_data |= M88E1000_PSCR_AUTO_X_MODE;
#endif

#if 0
        /* Options:
         *   disable_polarity_correction = 0 (default)
         *       Automatic Correction for Reversed Cable Polarity
         *   0 - Disabled
         *   1 - Enabled
         */
        phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
        if (hw->disable_polarity_correction == 1)
                phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
#else
        phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
#endif
        if (e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data) < 0) {
                DEBUGOUT("PHY Write Error\n");
                return -E1000_ERR_PHY;
        }

        /* Force TX_CLK in the Extended PHY Specific Control Register
         * to 25MHz clock.
         */
        if (e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        phy_data |= M88E1000_EPSCR_TX_CLK_25;
        /* Configure Master and Slave downshift values */
        phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
                      M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
        phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
                     M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
        if (e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data) < 0) {
                DEBUGOUT("PHY Write Error\n");
                return -E1000_ERR_PHY;
        }

        /* SW Reset the PHY so all changes take effect */
        ret_val = e1000_phy_reset(hw);
        if (ret_val < 0) {
                DEBUGOUT("Error Resetting the PHY\n");
                return ret_val;
        }

        /* Options:
         *   autoneg = 1 (default)
         *      PHY will advertise value(s) parsed from
         *      autoneg_advertised and fc
         *   autoneg = 0
         *      PHY will be set to 10H, 10F, 100H, or 100F
         *      depending on value parsed from forced_speed_duplex.
         */

        /* Is autoneg enabled?  This is enabled by default or by software override.
         * If so, call e1000_phy_setup_autoneg routine to parse the
         * autoneg_advertised and fc options. If autoneg is NOT enabled, then the
         * user should have provided a speed/duplex override.  If so, then call
         * e1000_phy_force_speed_duplex to parse and set this up.
         */
        /* Perform some bounds checking on the hw->autoneg_advertised
         * parameter.  If this variable is zero, then set it to the default.
         */
        hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;

        /* If autoneg_advertised is zero, we assume it was not defaulted
         * by the calling code so we set to advertise full capability.
         */
        if (hw->autoneg_advertised == 0)
                hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;

        DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
        ret_val = e1000_phy_setup_autoneg(hw);
        if (ret_val < 0) {
                DEBUGOUT("Error Setting up Auto-Negotiation\n");
                return ret_val;
        }
        DEBUGOUT("Restarting Auto-Neg\n");

        /* Restart auto-negotiation by setting the Auto Neg Enable bit and
         * the Auto Neg Restart bit in the PHY control register.
         */
        if (e1000_read_phy_reg(hw, PHY_CTRL, &phy_data) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
        if (e1000_write_phy_reg(hw, PHY_CTRL, phy_data) < 0) {
                DEBUGOUT("PHY Write Error\n");
                return -E1000_ERR_PHY;
        }
#if 0
        /* Does the user want to wait for Auto-Neg to complete here, or
         * check at a later time (for example, callback routine).
         */
        if (hw->wait_autoneg_complete) {
                ret_val = e1000_wait_autoneg(hw);
                if (ret_val < 0) {
                        DEBUGOUT
                            ("Error while waiting for autoneg to complete\n");
                        return ret_val;
                }
        }
#else
        /* If we do not wait for autonegtation to complete I
         * do not see a valid link status.
         */
        ret_val = e1000_wait_autoneg(hw);
        if (ret_val < 0) {
                DEBUGOUT("Error while waiting for autoneg to complete\n");
                return ret_val;
        }
#endif

        /* Check link status. Wait up to 100 microseconds for link to become
         * valid.
         */
        for (i = 0; i < 10; i++) {
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (phy_data & MII_SR_LINK_STATUS) {
                        /* We have link, so we need to finish the config process:
                         *   1) Set up the MAC to the current PHY speed/duplex
                         *      if we are on 82543.  If we
                         *      are on newer silicon, we only need to configure
                         *      collision distance in the Transmit Control Register.
                         *   2) Set up flow control on the MAC to that established with
                         *      the link partner.
                         */
                        if (hw->mac_type >= e1000_82544) {
                                e1000_config_collision_dist(hw);
                        } else {
                                ret_val = e1000_config_mac_to_phy(hw);
                                if (ret_val < 0) {
                                        DEBUGOUT
                                            ("Error configuring MAC to PHY settings\n");
                                        return ret_val;
                                }
                        }
                        ret_val = e1000_config_fc_after_link_up(hw);
                        if (ret_val < 0) {
                                DEBUGOUT("Error Configuring Flow Control\n");
                                return ret_val;
                        }
                        DEBUGOUT("Valid link established!!!\n");
                        return 0;
                }
                udelay(10);
        }

        DEBUGOUT("Unable to establish link!!!\n");
        return -E1000_ERR_NOLINK;
}

/******************************************************************************
* Configures PHY autoneg and flow control advertisement settings
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int
e1000_phy_setup_autoneg(struct e1000_hw *hw)
{
        uint16_t mii_autoneg_adv_reg;
        uint16_t mii_1000t_ctrl_reg;

        DEBUGFUNC();

        /* Read the MII Auto-Neg Advertisement Register (Address 4). */
        if (e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }

        /* Read the MII 1000Base-T Control Register (Address 9). */
        if (e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }

        /* Need to parse both autoneg_advertised and fc and set up
         * the appropriate PHY registers.  First we will parse for
         * autoneg_advertised software override.  Since we can advertise
         * a plethora of combinations, we need to check each bit
         * individually.
         */

        /* First we clear all the 10/100 mb speed bits in the Auto-Neg
         * Advertisement Register (Address 4) and the 1000 mb speed bits in
         * the  1000Base-T Control Register (Address 9).
         */
        mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
        mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;

        DEBUGOUT("autoneg_advertised %x\n", hw->autoneg_advertised);

        /* Do we want to advertise 10 Mb Half Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
                DEBUGOUT("Advertise 10mb Half duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
        }

        /* Do we want to advertise 10 Mb Full Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
                DEBUGOUT("Advertise 10mb Full duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
        }

        /* Do we want to advertise 100 Mb Half Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
                DEBUGOUT("Advertise 100mb Half duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
        }

        /* Do we want to advertise 100 Mb Full Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
                DEBUGOUT("Advertise 100mb Full duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
        }

        /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
        if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
                DEBUGOUT
                    ("Advertise 1000mb Half duplex requested, request denied!\n");
        }

        /* Do we want to advertise 1000 Mb Full Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
                DEBUGOUT("Advertise 1000mb Full duplex\n");
                mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
        }

        /* Check for a software override of the flow control settings, and
         * setup the PHY advertisement registers accordingly.  If
         * auto-negotiation is enabled, then software will have to set the
         * "PAUSE" bits to the correct value in the Auto-Negotiation
         * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
         *
         * The possible values of the "fc" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause frames
         *          but not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames
         *          but we do not support receiving pause frames).
         *      3:  Both Rx and TX flow control (symmetric) are enabled.
         *  other:  No software override.  The flow control configuration
         *          in the EEPROM is used.
         */
        switch (hw->fc) {
        case e1000_fc_none:     /* 0 */
                /* Flow control (RX & TX) is completely disabled by a
                 * software over-ride.
                 */
                mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
                break;
        case e1000_fc_rx_pause: /* 1 */
                /* RX Flow control is enabled, and TX Flow control is
                 * disabled, by a software over-ride.
                 */
                /* Since there really isn't a way to advertise that we are
                 * capable of RX Pause ONLY, we will advertise that we
                 * support both symmetric and asymmetric RX PAUSE.  Later
                 * (in e1000_config_fc_after_link_up) we will disable the
                 *hw's ability to send PAUSE frames.
                 */
                mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
                break;
        case e1000_fc_tx_pause: /* 2 */
                /* TX Flow control is enabled, and RX Flow control is
                 * disabled, by a software over-ride.
                 */
                mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
                mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
                break;
        case e1000_fc_full:     /* 3 */
                /* Flow control (both RX and TX) is enabled by a software
                 * over-ride.
                 */
                mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
                break;
        default:
                DEBUGOUT("Flow control param set incorrectly\n");
                return -E1000_ERR_CONFIG;
        }

        if (e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg) < 0) {
                DEBUGOUT("PHY Write Error\n");
                return -E1000_ERR_PHY;
        }

        DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);

        if (e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg) < 0) {
                DEBUGOUT("PHY Write Error\n");
                return -E1000_ERR_PHY;
        }
        return 0;
}

/******************************************************************************
* Sets the collision distance in the Transmit Control register
*
* hw - Struct containing variables accessed by shared code
*
* Link should have been established previously. Reads the speed and duplex
* information from the Device Status register.
******************************************************************************/
static void
e1000_config_collision_dist(struct e1000_hw *hw)
{
        uint32_t tctl;

        tctl = E1000_READ_REG(hw, TCTL);

        tctl &= ~E1000_TCTL_COLD;
        tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;

        E1000_WRITE_REG(hw, TCTL, tctl);
        E1000_WRITE_FLUSH(hw);
}

/******************************************************************************
* Sets MAC speed and duplex settings to reflect the those in the PHY
*
* hw - Struct containing variables accessed by shared code
* mii_reg - data to write to the MII control register
*
* The contents of the PHY register containing the needed information need to
* be passed in.
******************************************************************************/
static int
e1000_config_mac_to_phy(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint16_t phy_data;

        DEBUGFUNC();

        /* Read the Device Control Register and set the bits to Force Speed
         * and Duplex.
         */
        ctrl = E1000_READ_REG(hw, CTRL);
        ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
        ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);

        /* Set up duplex in the Device Control and Transmit Control
         * registers depending on negotiated values.
         */
        if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        if (phy_data & M88E1000_PSSR_DPLX)
                ctrl |= E1000_CTRL_FD;
        else
                ctrl &= ~E1000_CTRL_FD;

        e1000_config_collision_dist(hw);

        /* Set up speed in the Device Control register depending on
         * negotiated values.
         */
        if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
                ctrl |= E1000_CTRL_SPD_1000;
        else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
                ctrl |= E1000_CTRL_SPD_100;
        /* Write the configured values back to the Device Control Reg. */
        E1000_WRITE_REG(hw, CTRL, ctrl);
        return 0;
}

/******************************************************************************
 * Forces the MAC's flow control settings.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Sets the TFCE and RFCE bits in the device control register to reflect
 * the adapter settings. TFCE and RFCE need to be explicitly set by
 * software when a Copper PHY is used because autonegotiation is managed
 * by the PHY rather than the MAC. Software must also configure these
 * bits when link is forced on a fiber connection.
 *****************************************************************************/
static int
e1000_force_mac_fc(struct e1000_hw *hw)
{
        uint32_t ctrl;

        DEBUGFUNC();

        /* Get the current configuration of the Device Control Register */
        ctrl = E1000_READ_REG(hw, CTRL);

        /* Because we didn't get link via the internal auto-negotiation
         * mechanism (we either forced link or we got link via PHY
         * auto-neg), we have to manually enable/disable transmit an
         * receive flow control.
         *
         * The "Case" statement below enables/disable flow control
         * according to the "hw->fc" parameter.
         *
         * The possible values of the "fc" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause
         *          frames but not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames
         *          frames but we do not receive pause frames).
         *      3:  Both Rx and TX flow control (symmetric) is enabled.
         *  other:  No other values should be possible at this point.
         */

        switch (hw->fc) {
        case e1000_fc_none:
                ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
                break;
        case e1000_fc_rx_pause:
                ctrl &= (~E1000_CTRL_TFCE);
                ctrl |= E1000_CTRL_RFCE;
                break;
        case e1000_fc_tx_pause:
                ctrl &= (~E1000_CTRL_RFCE);
                ctrl |= E1000_CTRL_TFCE;
                break;
        case e1000_fc_full:
                ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
                break;
        default:
                DEBUGOUT("Flow control param set incorrectly\n");
                return -E1000_ERR_CONFIG;
        }

        /* Disable TX Flow Control for 82542 (rev 2.0) */
        if (hw->mac_type == e1000_82542_rev2_0)
                ctrl &= (~E1000_CTRL_TFCE);

        E1000_WRITE_REG(hw, CTRL, ctrl);
        return 0;
}

/******************************************************************************
 * Configures flow control settings after link is established
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Should be called immediately after a valid link has been established.
 * Forces MAC flow control settings if link was forced. When in MII/GMII mode
 * and autonegotiation is enabled, the MAC flow control settings will be set
 * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
 * and RFCE bits will be automaticaly set to the negotiated flow control mode.
 *****************************************************************************/
static int
e1000_config_fc_after_link_up(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t mii_status_reg;
        uint16_t mii_nway_adv_reg;
        uint16_t mii_nway_lp_ability_reg;
        uint16_t speed;
        uint16_t duplex;

        DEBUGFUNC();

        /* Check for the case where we have fiber media and auto-neg failed
         * so we had to force link.  In this case, we need to force the
         * configuration of the MAC to match the "fc" parameter.
         */
        if ((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) {
                ret_val = e1000_force_mac_fc(hw);
                if (ret_val < 0) {
                        DEBUGOUT("Error forcing flow control settings\n");
                        return ret_val;
                }
        }

        /* Check for the case where we have copper media and auto-neg is
         * enabled.  In this case, we need to check and see if Auto-Neg
         * has completed, and if so, how the PHY and link partner has
         * flow control configured.
         */
        if (hw->media_type == e1000_media_type_copper) {
                /* Read the MII Status Register and check to see if AutoNeg
                 * has completed.  We read this twice because this reg has
                 * some "sticky" (latched) bits.
                 */
                if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
                        DEBUGOUT("PHY Read Error \n");
                        return -E1000_ERR_PHY;
                }
                if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
                        DEBUGOUT("PHY Read Error \n");
                        return -E1000_ERR_PHY;
                }

                if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
                        /* The AutoNeg process has completed, so we now need to
                         * read both the Auto Negotiation Advertisement Register
                         * (Address 4) and the Auto_Negotiation Base Page Ability
                         * Register (Address 5) to determine how flow control was
                         * negotiated.
                         */
                        if (e1000_read_phy_reg
                            (hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) {
                                DEBUGOUT("PHY Read Error\n");
                                return -E1000_ERR_PHY;
                        }
                        if (e1000_read_phy_reg
                            (hw, PHY_LP_ABILITY,
                             &mii_nway_lp_ability_reg) < 0) {
                                DEBUGOUT("PHY Read Error\n");
                                return -E1000_ERR_PHY;
                        }

                        /* Two bits in the Auto Negotiation Advertisement Register
                         * (Address 4) and two bits in the Auto Negotiation Base
                         * Page Ability Register (Address 5) determine flow control
                         * for both the PHY and the link partner.  The following
                         * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
                         * 1999, describes these PAUSE resolution bits and how flow
                         * control is determined based upon these settings.
                         * NOTE:  DC = Don't Care
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
                         *-------|---------|-------|---------|--------------------
                         *   0   |    0    |  DC   |   DC    | e1000_fc_none
                         *   0   |    1    |   0   |   DC    | e1000_fc_none
                         *   0   |    1    |   1   |    0    | e1000_fc_none
                         *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
                         *   1   |    0    |   0   |   DC    | e1000_fc_none
                         *   1   |   DC    |   1   |   DC    | e1000_fc_full
                         *   1   |    1    |   0   |    0    | e1000_fc_none
                         *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
                         *
                         */
                        /* Are both PAUSE bits set to 1?  If so, this implies
                         * Symmetric Flow Control is enabled at both ends.  The
                         * ASM_DIR bits are irrelevant per the spec.
                         *
                         * For Symmetric Flow Control:
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
                         *-------|---------|-------|---------|--------------------
                         *   1   |   DC    |   1   |   DC    | e1000_fc_full
                         *
                         */
                        if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
                            (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
                                /* Now we need to check if the user selected RX ONLY
                                 * of pause frames.  In this case, we had to advertise
                                 * FULL flow control because we could not advertise RX
                                 * ONLY. Hence, we must now check to see if we need to
                                 * turn OFF  the TRANSMISSION of PAUSE frames.
                                 */
                                if (hw->original_fc == e1000_fc_full) {
                                        hw->fc = e1000_fc_full;
                                        DEBUGOUT("Flow Control = FULL.\r\n");
                                } else {
                                        hw->fc = e1000_fc_rx_pause;
                                        DEBUGOUT
                                            ("Flow Control = RX PAUSE frames only.\r\n");
                                }
                        }
                        /* For receiving PAUSE frames ONLY.
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
                         *-------|---------|-------|---------|--------------------
                         *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
                         *
                         */
                        else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
                                 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
                                 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
                                 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
                        {
                                hw->fc = e1000_fc_tx_pause;
                                DEBUGOUT
                                    ("Flow Control = TX PAUSE frames only.\r\n");
                        }
                        /* For transmitting PAUSE frames ONLY.
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
                         *-------|---------|-------|---------|--------------------
                         *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
                         *
                         */
                        else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
                                 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
                                 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
                                 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
                        {
                                hw->fc = e1000_fc_rx_pause;
                                DEBUGOUT
                                    ("Flow Control = RX PAUSE frames only.\r\n");
                        }
                        /* Per the IEEE spec, at this point flow control should be
                         * disabled.  However, we want to consider that we could
                         * be connected to a legacy switch that doesn't advertise
                         * desired flow control, but can be forced on the link
                         * partner.  So if we advertised no flow control, that is
                         * what we will resolve to.  If we advertised some kind of
                         * receive capability (Rx Pause Only or Full Flow Control)
                         * and the link partner advertised none, we will configure
                         * ourselves to enable Rx Flow Control only.  We can do
                         * this safely for two reasons:  If the link partner really
                         * didn't want flow control enabled, and we enable Rx, no
                         * harm done since we won't be receiving any PAUSE frames
                         * anyway.  If the intent on the link partner was to have
                         * flow control enabled, then by us enabling RX only, we
                         * can at least receive pause frames and process them.
                         * This is a good idea because in most cases, since we are
                         * predominantly a server NIC, more times than not we will
                         * be asked to delay transmission of packets than asking
                         * our link partner to pause transmission of frames.
                         */
                        else if (hw->original_fc == e1000_fc_none ||
                                 hw->original_fc == e1000_fc_tx_pause) {
                                hw->fc = e1000_fc_none;
                                DEBUGOUT("Flow Control = NONE.\r\n");
                        } else {
                                hw->fc = e1000_fc_rx_pause;
                                DEBUGOUT
                                    ("Flow Control = RX PAUSE frames only.\r\n");
                        }

                        /* Now we need to do one last check...  If we auto-
                         * negotiated to HALF DUPLEX, flow control should not be
                         * enabled per IEEE 802.3 spec.
                         */
                        e1000_get_speed_and_duplex(hw, &speed, &duplex);

                        if (duplex == HALF_DUPLEX)
                                hw->fc = e1000_fc_none;

                        /* Now we call a subroutine to actually force the MAC
                         * controller to use the correct flow control settings.
                         */
                        ret_val = e1000_force_mac_fc(hw);
                        if (ret_val < 0) {
                                DEBUGOUT
                                    ("Error forcing flow control settings\n");
                                return ret_val;
                        }
                } else {
                        DEBUGOUT
                            ("Copper PHY and Auto Neg has not completed.\r\n");
                }
        }
        return 0;
}

/******************************************************************************
 * Checks to see if the link status of the hardware has changed.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Called by any function that needs to check the link status of the adapter.
 *****************************************************************************/
static int
e1000_check_for_link(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        uint32_t rxcw;
        uint32_t ctrl;
        uint32_t status;
        uint32_t rctl;
        uint32_t signal;
        int32_t ret_val;
        uint16_t phy_data;
        uint16_t lp_capability;

        DEBUGFUNC();

        /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
         * set when the optics detect a signal. On older adapters, it will be
         * cleared when there is a signal
         */
        ctrl = E1000_READ_REG(hw, CTRL);
        if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS))
                signal = E1000_CTRL_SWDPIN1;
        else
                signal = 0;

        status = E1000_READ_REG(hw, STATUS);
        rxcw = E1000_READ_REG(hw, RXCW);
        DEBUGOUT("ctrl: %#08x status %#08x rxcw %#08x\n", ctrl, status, rxcw);

        /* If we have a copper PHY then we only want to go out to the PHY
         * registers to see if Auto-Neg has completed and/or if our link
         * status has changed.  The get_link_status flag will be set if we
         * receive a Link Status Change interrupt or we have Rx Sequence
         * Errors.
         */
        if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
                /* First we want to see if the MII Status Register reports
                 * link.  If so, then we want to get the current speed/duplex
                 * of the PHY.
                 * Read the register twice since the link bit is sticky.
                 */
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }

                if (phy_data & MII_SR_LINK_STATUS) {
                        hw->get_link_status = FALSE;
                } else {
                        /* No link detected */
                        return -E1000_ERR_NOLINK;
                }

                /* We have a M88E1000 PHY and Auto-Neg is enabled.  If we
                 * have Si on board that is 82544 or newer, Auto
                 * Speed Detection takes care of MAC speed/duplex
                 * configuration.  So we only need to configure Collision
                 * Distance in the MAC.  Otherwise, we need to force
                 * speed/duplex on the MAC to the current PHY speed/duplex
                 * settings.
                 */
                if (hw->mac_type >= e1000_82544)
                        e1000_config_collision_dist(hw);
                else {
                        ret_val = e1000_config_mac_to_phy(hw);
                        if (ret_val < 0) {
                                DEBUGOUT
                                    ("Error configuring MAC to PHY settings\n");
                                return ret_val;
                        }
                }

                /* Configure Flow Control now that Auto-Neg has completed. First, we
                 * need to restore the desired flow control settings because we may
                 * have had to re-autoneg with a different link partner.
                 */
                ret_val = e1000_config_fc_after_link_up(hw);
                if (ret_val < 0) {
                        DEBUGOUT("Error configuring flow control\n");
                        return ret_val;
                }

                /* At this point we know that we are on copper and we have
                 * auto-negotiated link.  These are conditions for checking the link
                 * parter capability register.  We use the link partner capability to
                 * determine if TBI Compatibility needs to be turned on or off.  If
                 * the link partner advertises any speed in addition to Gigabit, then
                 * we assume that they are GMII-based, and TBI compatibility is not
                 * needed. If no other speeds are advertised, we assume the link
                 * partner is TBI-based, and we turn on TBI Compatibility.
                 */
                if (hw->tbi_compatibility_en) {
                        if (e1000_read_phy_reg
                            (hw, PHY_LP_ABILITY, &lp_capability) < 0) {
                                DEBUGOUT("PHY Read Error\n");
                                return -E1000_ERR_PHY;
                        }
                        if (lp_capability & (NWAY_LPAR_10T_HD_CAPS |
                                             NWAY_LPAR_10T_FD_CAPS |
                                             NWAY_LPAR_100TX_HD_CAPS |
                                             NWAY_LPAR_100TX_FD_CAPS |
                                             NWAY_LPAR_100T4_CAPS)) {
                                /* If our link partner advertises anything in addition to
                                 * gigabit, we do not need to enable TBI compatibility.
                                 */
                                if (hw->tbi_compatibility_on) {
                                        /* If we previously were in the mode, turn it off. */
                                        rctl = E1000_READ_REG(hw, RCTL);
                                        rctl &= ~E1000_RCTL_SBP;
                                        E1000_WRITE_REG(hw, RCTL, rctl);
                                        hw->tbi_compatibility_on = FALSE;
                                }
                        } else {
                                /* If TBI compatibility is was previously off, turn it on. For
                                 * compatibility with a TBI link partner, we will store bad
                                 * packets. Some frames have an additional byte on the end and
                                 * will look like CRC errors to to the hardware.
                                 */
                                if (!hw->tbi_compatibility_on) {
                                        hw->tbi_compatibility_on = TRUE;
                                        rctl = E1000_READ_REG(hw, RCTL);
                                        rctl |= E1000_RCTL_SBP;
                                        E1000_WRITE_REG(hw, RCTL, rctl);
                                }
                        }
                }
        }
        /* If we don't have link (auto-negotiation failed or link partner cannot
         * auto-negotiate), the cable is plugged in (we have signal), and our
         * link partner is not trying to auto-negotiate with us (we are receiving
         * idles or data), we need to force link up. We also need to give
         * auto-negotiation time to complete, in case the cable was just plugged
         * in. The autoneg_failed flag does this.
         */
        else if ((hw->media_type == e1000_media_type_fiber) &&
                 (!(status & E1000_STATUS_LU)) &&
                 ((ctrl & E1000_CTRL_SWDPIN1) == signal) &&
                 (!(rxcw & E1000_RXCW_C))) {
                if (hw->autoneg_failed == 0) {
                        hw->autoneg_failed = 1;
                        return 0;
                }
                DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");

                /* Disable auto-negotiation in the TXCW register */
                E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE));

                /* Force link-up and also force full-duplex. */
                ctrl = E1000_READ_REG(hw, CTRL);
                ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
                E1000_WRITE_REG(hw, CTRL, ctrl);

                /* Configure Flow Control after forcing link up. */
                ret_val = e1000_config_fc_after_link_up(hw);
                if (ret_val < 0) {
                        DEBUGOUT("Error configuring flow control\n");
                        return ret_val;
                }
        }
        /* If we are forcing link and we are receiving /C/ ordered sets, re-enable
         * auto-negotiation in the TXCW register and disable forced link in the
         * Device Control register in an attempt to auto-negotiate with our link
         * partner.
         */
        else if ((hw->media_type == e1000_media_type_fiber) &&
                 (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
                DEBUGOUT
                    ("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
                E1000_WRITE_REG(hw, TXCW, hw->txcw);
                E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
        }
        return 0;
}

/******************************************************************************
 * Detects the current speed and duplex settings of the hardware.
 *
 * hw - Struct containing variables accessed by shared code
 * speed - Speed of the connection
 * duplex - Duplex setting of the connection
 *****************************************************************************/
static void
e1000_get_speed_and_duplex(struct e1000_hw *hw,
                           uint16_t * speed, uint16_t * duplex)
{
        uint32_t status;

        DEBUGFUNC();

        if (hw->mac_type >= e1000_82543) {
                status = E1000_READ_REG(hw, STATUS);
                if (status & E1000_STATUS_SPEED_1000) {
                        *speed = SPEED_1000;
                        DEBUGOUT("1000 Mbs, ");
                } else if (status & E1000_STATUS_SPEED_100) {
                        *speed = SPEED_100;
                        DEBUGOUT("100 Mbs, ");
                } else {
                        *speed = SPEED_10;
                        DEBUGOUT("10 Mbs, ");
                }

                if (status & E1000_STATUS_FD) {
                        *duplex = FULL_DUPLEX;
                        DEBUGOUT("Full Duplex\r\n");
                } else {
                        *duplex = HALF_DUPLEX;
                        DEBUGOUT(" Half Duplex\r\n");
                }
        } else {
                DEBUGOUT("1000 Mbs, Full Duplex\r\n");
                *speed = SPEED_1000;
                *duplex = FULL_DUPLEX;
        }
}

/******************************************************************************
* Blocks until autoneg completes or times out (~4.5 seconds)
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int
e1000_wait_autoneg(struct e1000_hw *hw)
{
        uint16_t i;
        uint16_t phy_data;

        DEBUGFUNC();
        DEBUGOUT("Waiting for Auto-Neg to complete.\n");

        /* We will wait for autoneg to complete or 4.5 seconds to expire. */
        for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
                /* Read the MII Status Register and wait for Auto-Neg
                 * Complete bit to be set.
                 */
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (phy_data & MII_SR_AUTONEG_COMPLETE) {
                        DEBUGOUT("Auto-Neg complete.\n");
                        return 0;
                }
                mdelay(100);
        }
        DEBUGOUT("Auto-Neg timedout.\n");
        return -E1000_ERR_TIMEOUT;
}

/******************************************************************************
* Raises the Management Data Clock
*
* hw - Struct containing variables accessed by shared code
* ctrl - Device control register's current value
******************************************************************************/
static void
e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl)
{
        /* Raise the clock input to the Management Data Clock (by setting the MDC
         * bit), and then delay 2 microseconds.
         */
        E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC));
        E1000_WRITE_FLUSH(hw);
        udelay(2);
}

/******************************************************************************
* Lowers the Management Data Clock
*
* hw - Struct containing variables accessed by shared code
* ctrl - Device control register's current value
******************************************************************************/
static void
e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl)
{
        /* Lower the clock input to the Management Data Clock (by clearing the MDC
         * bit), and then delay 2 microseconds.
         */
        E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC));
        E1000_WRITE_FLUSH(hw);
        udelay(2);
}

/******************************************************************************
* Shifts data bits out to the PHY
*
* hw - Struct containing variables accessed by shared code
* data - Data to send out to the PHY
* count - Number of bits to shift out
*
* Bits are shifted out in MSB to LSB order.
******************************************************************************/
static void
e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, uint16_t count)
{
        uint32_t ctrl;
        uint32_t mask;

        /* We need to shift "count" number of bits out to the PHY. So, the value
         * in the "data" parameter will be shifted out to the PHY one bit at a
         * time. In order to do this, "data" must be broken down into bits.
         */
        mask = 0x01;
        mask <<= (count - 1);

        ctrl = E1000_READ_REG(hw, CTRL);

        /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
        ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);

        while (mask) {
                /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
                 * then raising and lowering the Management Data Clock. A "0" is
                 * shifted out to the PHY by setting the MDIO bit to "0" and then
                 * raising and lowering the clock.
                 */
                if (data & mask)
                        ctrl |= E1000_CTRL_MDIO;
                else
                        ctrl &= ~E1000_CTRL_MDIO;

                E1000_WRITE_REG(hw, CTRL, ctrl);
                E1000_WRITE_FLUSH(hw);

                udelay(2);

                e1000_raise_mdi_clk(hw, &ctrl);
                e1000_lower_mdi_clk(hw, &ctrl);

                mask = mask >> 1;
        }
}

/******************************************************************************
* Shifts data bits in from the PHY
*
* hw - Struct containing variables accessed by shared code
*
* Bits are shifted in in MSB to LSB order.
******************************************************************************/
static uint16_t
e1000_shift_in_mdi_bits(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint16_t data = 0;
        uint8_t i;

        /* In order to read a register from the PHY, we need to shift in a total
         * of 18 bits from the PHY. The first two bit (turnaround) times are used
         * to avoid contention on the MDIO pin when a read operation is performed.
         * These two bits are ignored by us and thrown away. Bits are "shifted in"
         * by raising the input to the Management Data Clock (setting the MDC bit),
         * and then reading the value of the MDIO bit.
         */
        ctrl = E1000_READ_REG(hw, CTRL);

        /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
        ctrl &= ~E1000_CTRL_MDIO_DIR;
        ctrl &= ~E1000_CTRL_MDIO;

        E1000_WRITE_REG(hw, CTRL, ctrl);
        E1000_WRITE_FLUSH(hw);

        /* Raise and Lower the clock before reading in the data. This accounts for
         * the turnaround bits. The first clock occurred when we clocked out the
         * last bit of the Register Address.
         */
        e1000_raise_mdi_clk(hw, &ctrl);
        e1000_lower_mdi_clk(hw, &ctrl);

        for (data = 0, i = 0; i < 16; i++) {
                data = data << 1;
                e1000_raise_mdi_clk(hw, &ctrl);
                ctrl = E1000_READ_REG(hw, CTRL);
                /* Check to see if we shifted in a "1". */
                if (ctrl & E1000_CTRL_MDIO)
                        data |= 1;
                e1000_lower_mdi_clk(hw, &ctrl);
        }

        e1000_raise_mdi_clk(hw, &ctrl);
        e1000_lower_mdi_clk(hw, &ctrl);

        return data;
}

/*****************************************************************************
* Reads the value from a PHY register
*
* hw - Struct containing variables accessed by shared code
* reg_addr - address of the PHY register to read
******************************************************************************/
static int
e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t * phy_data)
{
        uint32_t i;
        uint32_t mdic = 0;
        const uint32_t phy_addr = 1;

        if (reg_addr > MAX_PHY_REG_ADDRESS) {
                DEBUGOUT("PHY Address %d is out of range\n", reg_addr);
                return -E1000_ERR_PARAM;
        }

        if (hw->mac_type > e1000_82543) {
                /* Set up Op-code, Phy Address, and register address in the MDI
                 * Control register.  The MAC will take care of interfacing with the
                 * PHY to retrieve the desired data.
                 */
                mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
                        (phy_addr << E1000_MDIC_PHY_SHIFT) |
                        (E1000_MDIC_OP_READ));

                E1000_WRITE_REG(hw, MDIC, mdic);

                /* Poll the ready bit to see if the MDI read completed */
                for (i = 0; i < 64; i++) {
                        udelay(10);
                        mdic = E1000_READ_REG(hw, MDIC);
                        if (mdic & E1000_MDIC_READY)
                                break;
                }
                if (!(mdic & E1000_MDIC_READY)) {
                        DEBUGOUT("MDI Read did not complete\n");
                        return -E1000_ERR_PHY;
                }
                if (mdic & E1000_MDIC_ERROR) {
                        DEBUGOUT("MDI Error\n");
                        return -E1000_ERR_PHY;
                }
                *phy_data = (uint16_t) mdic;
        } else {
                /* We must first send a preamble through the MDIO pin to signal the
                 * beginning of an MII instruction.  This is done by sending 32
                 * consecutive "1" bits.
                 */
                e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);

                /* Now combine the next few fields that are required for a read
                 * operation.  We use this method instead of calling the
                 * e1000_shift_out_mdi_bits routine five different times. The format of
                 * a MII read instruction consists of a shift out of 14 bits and is
                 * defined as follows:
                 *    <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
                 * followed by a shift in of 18 bits.  This first two bits shifted in
                 * are TurnAround bits used to avoid contention on the MDIO pin when a
                 * READ operation is performed.  These two bits are thrown away
                 * followed by a shift in of 16 bits which contains the desired data.
                 */
                mdic = ((reg_addr) | (phy_addr << 5) |
                        (PHY_OP_READ << 10) | (PHY_SOF << 12));

                e1000_shift_out_mdi_bits(hw, mdic, 14);

                /* Now that we've shifted out the read command to the MII, we need to
                 * "shift in" the 16-bit value (18 total bits) of the requested PHY
                 * register address.
                 */
                *phy_data = e1000_shift_in_mdi_bits(hw);
        }
        return 0;
}

/******************************************************************************
* Writes a value to a PHY register
*
* hw - Struct containing variables accessed by shared code
* reg_addr - address of the PHY register to write
* data - data to write to the PHY
******************************************************************************/
static int
e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data)
{
        uint32_t i;
        uint32_t mdic = 0;
        const uint32_t phy_addr = 1;

        if (reg_addr > MAX_PHY_REG_ADDRESS) {
                DEBUGOUT("PHY Address %d is out of range\n", reg_addr);
                return -E1000_ERR_PARAM;
        }

        if (hw->mac_type > e1000_82543) {
                /* Set up Op-code, Phy Address, register address, and data intended
                 * for the PHY register in the MDI Control register.  The MAC will take
                 * care of interfacing with the PHY to send the desired data.
                 */
                mdic = (((uint32_t) phy_data) |
                        (reg_addr << E1000_MDIC_REG_SHIFT) |
                        (phy_addr << E1000_MDIC_PHY_SHIFT) |
                        (E1000_MDIC_OP_WRITE));

                E1000_WRITE_REG(hw, MDIC, mdic);

                /* Poll the ready bit to see if the MDI read completed */
                for (i = 0; i < 64; i++) {
                        udelay(10);
                        mdic = E1000_READ_REG(hw, MDIC);
                        if (mdic & E1000_MDIC_READY)
                                break;
                }
                if (!(mdic & E1000_MDIC_READY)) {
                        DEBUGOUT("MDI Write did not complete\n");
                        return -E1000_ERR_PHY;
                }
        } else {
                /* We'll need to use the SW defined pins to shift the write command
                 * out to the PHY. We first send a preamble to the PHY to signal the
                 * beginning of the MII instruction.  This is done by sending 32
                 * consecutive "1" bits.
                 */
                e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);

                /* Now combine the remaining required fields that will indicate a
                 * write operation. We use this method instead of calling the
                 * e1000_shift_out_mdi_bits routine for each field in the command. The
                 * format of a MII write instruction is as follows:
                 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
                 */
                mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
                        (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
                mdic <<= 16;
                mdic |= (uint32_t) phy_data;

                e1000_shift_out_mdi_bits(hw, mdic, 32);
        }
        return 0;
}

/******************************************************************************
* Returns the PHY to the power-on reset state
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static void
e1000_phy_hw_reset(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint32_t ctrl_ext;

        DEBUGFUNC();

        DEBUGOUT("Resetting Phy...\n");

        if (hw->mac_type > e1000_82543) {
                /* Read the device control register and assert the E1000_CTRL_PHY_RST
                 * bit. Then, take it out of reset.
                 */
                ctrl = E1000_READ_REG(hw, CTRL);
                E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
                E1000_WRITE_FLUSH(hw);
                mdelay(10);
                E1000_WRITE_REG(hw, CTRL, ctrl);
                E1000_WRITE_FLUSH(hw);
        } else {
                /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
                 * bit to put the PHY into reset. Then, take it out of reset.
                 */
                ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
                ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
                ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
                E1000_WRITE_FLUSH(hw);
                mdelay(10);
                ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
                E1000_WRITE_FLUSH(hw);
        }
        udelay(150);
}

/******************************************************************************
* Resets the PHY
*
* hw - Struct containing variables accessed by shared code
*
* Sets bit 15 of the MII Control regiser
******************************************************************************/
static int
e1000_phy_reset(struct e1000_hw *hw)
{
        uint16_t phy_data;

        DEBUGFUNC();

        if (e1000_read_phy_reg(hw, PHY_CTRL, &phy_data) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        phy_data |= MII_CR_RESET;
        if (e1000_write_phy_reg(hw, PHY_CTRL, phy_data) < 0) {
                DEBUGOUT("PHY Write Error\n");
                return -E1000_ERR_PHY;
        }
        udelay(1);
        return 0;
}

/******************************************************************************
* Probes the expected PHY address for known PHY IDs
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int
e1000_detect_gig_phy(struct e1000_hw *hw)
{
        uint16_t phy_id_high, phy_id_low;
        int match = FALSE;

        DEBUGFUNC();

        /* Read the PHY ID Registers to identify which PHY is onboard. */
        if (e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        hw->phy_id = (uint32_t) (phy_id_high << 16);
        udelay(2);
        if (e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);

        switch (hw->mac_type) {
        case e1000_82543:
                if (hw->phy_id == M88E1000_E_PHY_ID)
                        match = TRUE;
                break;
        case e1000_82544:
                if (hw->phy_id == M88E1000_I_PHY_ID)
                        match = TRUE;
                break;
        case e1000_82540:
        case e1000_82545:
        case e1000_82546:
                if (hw->phy_id == M88E1011_I_PHY_ID)
                        match = TRUE;
                break;
        default:
                DEBUGOUT("Invalid MAC type %d\n", hw->mac_type);
                return -E1000_ERR_CONFIG;
        }
        if (match) {
                DEBUGOUT("PHY ID 0x%X detected\n", hw->phy_id);
                return 0;
        }
        DEBUGOUT("Invalid PHY ID 0x%X\n", hw->phy_id);
        return -E1000_ERR_PHY;
}

/**
 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
 *
 * e1000_sw_init initializes the Adapter private data structure.
 * Fields are initialized based on PCI device information and
 * OS network device settings (MTU size).
 **/

static int
e1000_sw_init(struct eth_device *nic, int cardnum)
{
        struct e1000_hw *hw = (typeof(hw)) nic->priv;
        int result;

        /* PCI config space info */
        pci_read_config_word(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id);
        pci_read_config_word(hw->pdev, PCI_DEVICE_ID, &hw->device_id);
        pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID,
                             &hw->subsystem_vendor_id);
        pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id);

        pci_read_config_byte(hw->pdev, PCI_REVISION_ID, &hw->revision_id);
        pci_read_config_word(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word);

        /* identify the MAC */
        result = e1000_set_mac_type(hw);
        if (result) {
                E1000_ERR("Unknown MAC Type\n");
                return result;
        }

        /* lan a vs. lan b settings */
        if (hw->mac_type == e1000_82546)
                /*this also works w/ multiple 82546 cards */
                /*but not if they're intermingled /w other e1000s */
                hw->lan_loc = (cardnum % 2) ? e1000_lan_b : e1000_lan_a;
        else
                hw->lan_loc = e1000_lan_a;

        /* flow control settings */
        hw->fc_high_water = E1000_FC_HIGH_THRESH;
        hw->fc_low_water = E1000_FC_LOW_THRESH;
        hw->fc_pause_time = E1000_FC_PAUSE_TIME;
        hw->fc_send_xon = 1;

        /* Media type - copper or fiber */

        if (hw->mac_type >= e1000_82543) {
                uint32_t status = E1000_READ_REG(hw, STATUS);

                if (status & E1000_STATUS_TBIMODE) {
                        DEBUGOUT("fiber interface\n");
                        hw->media_type = e1000_media_type_fiber;
                } else {
                        DEBUGOUT("copper interface\n");
                        hw->media_type = e1000_media_type_copper;
                }
        } else {
                hw->media_type = e1000_media_type_fiber;
        }

        if (hw->mac_type < e1000_82543)
                hw->report_tx_early = 0;
        else
                hw->report_tx_early = 1;

        hw->tbi_compatibility_en = TRUE;
#if 0
        hw->wait_autoneg_complete = FALSE;
        hw->adaptive_ifs = TRUE;

        /* Copper options */
        if (hw->media_type == e1000_media_type_copper) {
                hw->mdix = AUTO_ALL_MODES;
                hw->disable_polarity_correction = FALSE;
        }
#endif
        return E1000_SUCCESS;
}

void
fill_rx(struct e1000_hw *hw)
{
        struct e1000_rx_desc *rd;

        rx_last = rx_tail;
        rd = rx_base + rx_tail;
        rx_tail = (rx_tail + 1) % 8;
        memset(rd, 0, 16);
        rd->buffer_addr = cpu_to_le64((u32) & packet);
        E1000_WRITE_REG(hw, RDT, rx_tail);
}

/**
 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
 * @adapter: board private structure
 *
 * Configure the Tx unit of the MAC after a reset.
 **/

static void
e1000_configure_tx(struct e1000_hw *hw)
{
        unsigned long ptr;
        unsigned long tctl;
        unsigned long tipg;

        ptr = (u32) tx_pool;
        if (ptr & 0xf)
                ptr = (ptr + 0x10) & (~0xf);

        tx_base = (typeof(tx_base)) ptr;

        E1000_WRITE_REG(hw, TDBAL, (u32) tx_base);
        E1000_WRITE_REG(hw, TDBAH, 0);

        E1000_WRITE_REG(hw, TDLEN, 128);

        /* Setup the HW Tx Head and Tail descriptor pointers */
        E1000_WRITE_REG(hw, TDH, 0);
        E1000_WRITE_REG(hw, TDT, 0);
        tx_tail = 0;

        /* Set the default values for the Tx Inter Packet Gap timer */
        switch (hw->mac_type) {
        case e1000_82542_rev2_0:
        case e1000_82542_rev2_1:
                tipg = DEFAULT_82542_TIPG_IPGT;
                tipg |= DEFAULT_82542_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT;
                tipg |= DEFAULT_82542_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT;
                break;
        default:
                if (hw->media_type == e1000_media_type_fiber)
                        tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
                else
                        tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
                tipg |= DEFAULT_82543_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT;
                tipg |= DEFAULT_82543_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT;
        }
        E1000_WRITE_REG(hw, TIPG, tipg);
#if 0
        /* Set the Tx Interrupt Delay register */
        E1000_WRITE_REG(hw, TIDV, adapter->tx_int_delay);
        if (hw->mac_type >= e1000_82540)
                E1000_WRITE_REG(hw, TADV, adapter->tx_abs_int_delay);
#endif
        /* Program the Transmit Control Register */
        tctl = E1000_READ_REG(hw, TCTL);
        tctl &= ~E1000_TCTL_CT;
        tctl |= E1000_TCTL_EN | E1000_TCTL_PSP |
            (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
        E1000_WRITE_REG(hw, TCTL, tctl);

        e1000_config_collision_dist(hw);
#if 0
        /* Setup Transmit Descriptor Settings for this adapter */
        adapter->txd_cmd = E1000_TXD_CMD_IFCS | E1000_TXD_CMD_IDE;

        if (adapter->hw.report_tx_early == 1)
                adapter->txd_cmd |= E1000_TXD_CMD_RS;
        else
                adapter->txd_cmd |= E1000_TXD_CMD_RPS;
#endif
}

/**
 * e1000_setup_rctl - configure the receive control register
 * @adapter: Board private structure
 **/
static void
e1000_setup_rctl(struct e1000_hw *hw)
{
        uint32_t rctl;

        rctl = E1000_READ_REG(hw, RCTL);

        rctl &= ~(3 << E1000_RCTL_MO_SHIFT);

        rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF;     /* |
                                                                                                   (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */

        if (hw->tbi_compatibility_on == 1)
                rctl |= E1000_RCTL_SBP;
        else
                rctl &= ~E1000_RCTL_SBP;

        rctl &= ~(E1000_RCTL_SZ_4096);
#if 0
        switch (adapter->rx_buffer_len) {
        case E1000_RXBUFFER_2048:
        default:
#endif
                rctl |= E1000_RCTL_SZ_2048;
                rctl &= ~(E1000_RCTL_BSEX | E1000_RCTL_LPE);
#if 0
                break;
        case E1000_RXBUFFER_4096:
                rctl |= E1000_RCTL_SZ_4096 | E1000_RCTL_BSEX | E1000_RCTL_LPE;
                break;
        case E1000_RXBUFFER_8192:
                rctl |= E1000_RCTL_SZ_8192 | E1000_RCTL_BSEX | E1000_RCTL_LPE;
                break;
        case E1000_RXBUFFER_16384:
                rctl |= E1000_RCTL_SZ_16384 | E1000_RCTL_BSEX | E1000_RCTL_LPE;
                break;
        }
#endif
        E1000_WRITE_REG(hw, RCTL, rctl);
}

/**
 * e1000_configure_rx - Configure 8254x Receive Unit after Reset
 * @adapter: board private structure
 *
 * Configure the Rx unit of the MAC after a reset.
 **/
static void
e1000_configure_rx(struct e1000_hw *hw)
{
        unsigned long ptr;
        unsigned long rctl;
#if 0
        unsigned long rxcsum;
#endif
        rx_tail = 0;
        /* make sure receives are disabled while setting up the descriptors */
        rctl = E1000_READ_REG(hw, RCTL);
        E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
#if 0
        /* set the Receive Delay Timer Register */

        E1000_WRITE_REG(hw, RDTR, adapter->rx_int_delay);
#endif
        if (hw->mac_type >= e1000_82540) {
#if 0
                E1000_WRITE_REG(hw, RADV, adapter->rx_abs_int_delay);
#endif
                /* Set the interrupt throttling rate.  Value is calculated
                 * as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */
#define MAX_INTS_PER_SEC        8000
#define DEFAULT_ITR             1000000000/(MAX_INTS_PER_SEC * 256)
                E1000_WRITE_REG(hw, ITR, DEFAULT_ITR);
        }

        /* Setup the Base and Length of the Rx Descriptor Ring */
        ptr = (u32) rx_pool;
        if (ptr & 0xf)
                ptr = (ptr + 0x10) & (~0xf);
        rx_base = (typeof(rx_base)) ptr;
        E1000_WRITE_REG(hw, RDBAL, (u32) rx_base);
        E1000_WRITE_REG(hw, RDBAH, 0);

        E1000_WRITE_REG(hw, RDLEN, 128);

        /* Setup the HW Rx Head and Tail Descriptor Pointers */
        E1000_WRITE_REG(hw, RDH, 0);
        E1000_WRITE_REG(hw, RDT, 0);
#if 0
        /* Enable 82543 Receive Checksum Offload for TCP and UDP */
        if ((adapter->hw.mac_type >= e1000_82543) && (adapter->rx_csum == TRUE)) {
                rxcsum = E1000_READ_REG(hw, RXCSUM);
                rxcsum |= E1000_RXCSUM_TUOFL;
                E1000_WRITE_REG(hw, RXCSUM, rxcsum);
        }
#endif
        /* Enable Receives */

        E1000_WRITE_REG(hw, RCTL, rctl);
        fill_rx(hw);
}

/**************************************************************************
POLL - Wait for a frame
***************************************************************************/
static int
e1000_poll(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;
        struct e1000_rx_desc *rd;
        /* return true if there's an ethernet packet ready to read */
        rd = rx_base + rx_last;
        if (!(le32_to_cpu(rd->status)) & E1000_RXD_STAT_DD)
                return 0;
        /*DEBUGOUT("recv: packet len=%d \n", rd->length); */
        NetReceive((uchar *)packet, le32_to_cpu(rd->length));
        fill_rx(hw);
        return 1;
}

/**************************************************************************
TRANSMIT - Transmit a frame
***************************************************************************/
static int
e1000_transmit(struct eth_device *nic, volatile void *packet, int length)
{
        struct e1000_hw *hw = nic->priv;
        struct e1000_tx_desc *txp;
        int i = 0;

        txp = tx_base + tx_tail;
        tx_tail = (tx_tail + 1) % 8;

        txp->buffer_addr = cpu_to_le64(virt_to_bus(packet));
        txp->lower.data = cpu_to_le32(E1000_TXD_CMD_RPS | E1000_TXD_CMD_EOP |
                                      E1000_TXD_CMD_IFCS | length);
        txp->upper.data = 0;
        E1000_WRITE_REG(hw, TDT, tx_tail);

        while (!(le32_to_cpu(txp->upper.data) & E1000_TXD_STAT_DD)) {
                if (i++ > TOUT_LOOP) {
                        DEBUGOUT("e1000: tx timeout\n");
                        return 0;
                }
                udelay(10);     /* give the nic a chance to write to the register */
        }
        return 1;
}

/*reset function*/
static inline int
e1000_reset(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;

        e1000_reset_hw(hw);
        if (hw->mac_type >= e1000_82544) {
                E1000_WRITE_REG(hw, WUC, 0);
        }
        return e1000_init_hw(nic);
}

/**************************************************************************
DISABLE - Turn off ethernet interface
***************************************************************************/
static void
e1000_disable(struct eth_device *nic)
{
        struct e1000_hw *hw = nic->priv;

        /* Turn off the ethernet interface */
        E1000_WRITE_REG(hw, RCTL, 0);
        E1000_WRITE_REG(hw, TCTL, 0);

        /* Clear the transmit ring */
        E1000_WRITE_REG(hw, TDH, 0);
        E1000_WRITE_REG(hw, TDT, 0);

        /* Clear the receive ring */
        E1000_WRITE_REG(hw, RDH, 0);
        E1000_WRITE_REG(hw, RDT, 0);

        /* put the card in its initial state */
#if 0
        E1000_WRITE_REG(hw, CTRL, E1000_CTRL_RST);
#endif
        mdelay(10);

}

/**************************************************************************
INIT - set up ethernet interface(s)
***************************************************************************/
static int
e1000_init(struct eth_device *nic, bd_t * bis)
{
        struct e1000_hw *hw = nic->priv;
        int ret_val = 0;

        ret_val = e1000_reset(nic);
        if (ret_val < 0) {
                if ((ret_val == -E1000_ERR_NOLINK) ||
                    (ret_val == -E1000_ERR_TIMEOUT)) {
                        E1000_ERR("Valid Link not detected\n");
                } else {
                        E1000_ERR("Hardware Initialization Failed\n");
                }
                return 0;
        }
        e1000_configure_tx(hw);
        e1000_setup_rctl(hw);
        e1000_configure_rx(hw);
        return 1;
}

/**************************************************************************
PROBE - Look for an adapter, this routine's visible to the outside
You should omit the last argument struct pci_device * for a non-PCI NIC
***************************************************************************/
int
e1000_initialize(bd_t * bis)
{
        pci_dev_t devno;
        int card_number = 0;
        struct eth_device *nic = NULL;
        struct e1000_hw *hw = NULL;
        u32 iobase;
        int idx = 0;
        u32 PciCommandWord;

        while (1) {             /* Find PCI device(s) */
                if ((devno = pci_find_devices(supported, idx++)) < 0) {
                        break;
                }

                pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &iobase);
                iobase &= ~0xf; /* Mask the bits that say "this is an io addr" */
                DEBUGOUT("e1000#%d: iobase 0x%08x\n", card_number, iobase);

                pci_write_config_dword(devno, PCI_COMMAND,
                                       PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
                /* Check if I/O accesses and Bus Mastering are enabled. */
                pci_read_config_dword(devno, PCI_COMMAND, &PciCommandWord);
                if (!(PciCommandWord & PCI_COMMAND_MEMORY)) {
                        printf("Error: Can not enable MEM access.\n");
                        continue;
                } else if (!(PciCommandWord & PCI_COMMAND_MASTER)) {
                        printf("Error: Can not enable Bus Mastering.\n");
                        continue;
                }

                nic = (struct eth_device *) malloc(sizeof (*nic));
                hw = (struct e1000_hw *) malloc(sizeof (*hw));
                hw->pdev = devno;
                nic->priv = hw;
                nic->iobase = bus_to_phys(devno, iobase);

                sprintf(nic->name, "e1000#%d", card_number);

                /* Are these variables needed? */
#if 0
                hw->fc = e1000_fc_none;
                hw->original_fc = e1000_fc_none;
#else
                hw->fc = e1000_fc_default;
                hw->original_fc = e1000_fc_default;
#endif
                hw->autoneg_failed = 0;
                hw->get_link_status = TRUE;
                hw->hw_addr = (typeof(hw->hw_addr)) iobase;
                hw->mac_type = e1000_undefined;

                /* MAC and Phy settings */
                if (e1000_sw_init(nic, card_number) < 0) {
                        free(hw);
                        free(nic);
                        return 0;
                }
#ifndef CONFIG_AP1000
                if (e1000_validate_eeprom_checksum(nic) < 0) {
                        printf("The EEPROM Checksum Is Not Valid\n");
                        free(hw);
                        free(nic);
                        return 0;
                }
#endif
                e1000_read_mac_addr(nic);

                E1000_WRITE_REG(hw, PBA, E1000_DEFAULT_PBA);

                printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n",
                       nic->enetaddr[0], nic->enetaddr[1], nic->enetaddr[2],
                       nic->enetaddr[3], nic->enetaddr[4], nic->enetaddr[5]);

                nic->init = e1000_init;
                nic->recv = e1000_poll;
                nic->send = e1000_transmit;
                nic->halt = e1000_disable;

                eth_register(nic);

                card_number++;
        }
        return 1;
}

#endif