drivers/i2c/Kconfig

   1 #
   2 # I2C subsystem configuration
   3 #
   4
   5 menu "I2C support"
   6
   7 config DM_I2C
   8         bool "Enable Driver Model for I2C drivers"
   9         depends on DM
  10         help
  11           Enable driver model for I2C. The I2C uclass interface: probe, read,
  12           write and speed, is implemented with the bus drivers operations,
  13           which provide methods for bus setting and data transfer. Each chip
  14           device (bus child) info is kept as parent platdata. The interface
  15           is defined in include/i2c.h. When i2c bus driver supports the i2c
  16           uclass, but the device drivers not, then DM_I2C_COMPAT config can
  17           be used as compatibility layer.
  18
  19 config DM_I2C_COMPAT
  20         bool "Enable I2C compatibility layer"
  21         depends on DM
  22         help
  23           Enable old-style I2C functions for compatibility with existing code.
  24           This option can be enabled as a temporary measure to avoid needing
  25           to convert all code for a board in a single commit. It should not
  26           be enabled for any board in an official release.
  27
  28 config I2C_CROS_EC_TUNNEL
  29         tristate "Chrome OS EC tunnel I2C bus"
  30         depends on CROS_EC
  31         help
  32           This provides an I2C bus that will tunnel i2c commands through to
  33           the other side of the Chrome OS EC to the I2C bus connected there.
  34           This will work whatever the interface used to talk to the EC (SPI,
  35           I2C or LPC). Some Chromebooks use this when the hardware design
  36           does not allow direct access to the main PMIC from the AP.
  37
  38 config I2C_CROS_EC_LDO
  39         bool "Provide access to LDOs on the Chrome OS EC"
  40         depends on CROS_EC
  41         ---help---
  42         On many Chromebooks the main PMIC is inaccessible to the AP. This is
  43         often dealt with by using an I2C pass-through interface provided by
  44         the EC. On some unfortunate models (e.g. Spring) the pass-through
  45         is not available, and an LDO message is available instead. This
  46         option enables a driver which provides very basic access to those
  47         regulators, via the EC. We implement this as an I2C bus which
  48         emulates just the TPS65090 messages we know about. This is done to
  49         avoid duplicating the logic in the TPS65090 regulator driver for
  50         enabling/disabling an LDO.
  51
  52 config DM_I2C_GPIO
  53         bool "Enable Driver Model for software emulated I2C bus driver"
  54         depends on DM_I2C && DM_GPIO
  55         help
  56           Enable the i2c bus driver emulation by using the GPIOs. The bus GPIO
  57           configuration is given by the device tree. Kernel-style device tree
  58           bindings are supported.
  59           Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
  60
  61 config SYS_I2C_AT91
  62         bool "Atmel I2C driver"
  63         depends on DM_I2C && ARCH_AT91
  64         help
  65           Add support for the Atmel I2C driver. A serious problem is that there
  66           is no documented way to issue repeated START conditions for more than
  67           two messages, as needed to support combined I2C messages. Use the
  68           i2c-gpio driver unless your system can cope with this limitation.
  69           Binding info: doc/device-tree-bindings/i2c/i2c-at91.txt
  70
  71 config SYS_I2C_FSL
  72        bool "Freescale I2C bus driver"
  73        depends on DM_I2C
  74        help
  75           Add support for Freescale I2C busses as used on MPC8240, MPC8245, and
  76           MPC85xx processors.
  77
  78 config SYS_I2C_CADENCE
  79         tristate "Cadence I2C Controller"
  80         depends on DM_I2C && (ARCH_ZYNQ || ARM64)
  81         help
  82           Say yes here to select Cadence I2C Host Controller. This controller is
  83           e.g. used by Xilinx Zynq.
  84
  85 config SYS_I2C_DW
  86         bool "Designware I2C Controller"
  87         default n
  88         help
  89           Say yes here to select the Designware I2C Host Controller. This
  90           controller is used in various SoCs, e.g. the ST SPEAr, Altera
  91           SoCFPGA, Synopsys ARC700 and some Intel x86 SoCs.
  92
  93 config SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
  94         bool "DW I2C Enable Status Register not supported"
  95         depends on SYS_I2C_DW && (TARGET_SPEAR300 || TARGET_SPEAR310 || \
  96                 TARGET_SPEAR320 || TARGET_SPEAR600 || TARGET_X600)
  97         default y
  98         help
  99           Some versions of the Designware I2C controller do not support the
 100           enable status register. This config option can be enabled in such
 101           cases.
 102
 103 config SYS_I2C_INTEL
 104         bool "Intel I2C/SMBUS driver"
 105         depends on DM_I2C
 106         help
 107           Add support for the Intel SMBUS driver. So far this driver is just
 108           a stub which perhaps some basic init. There is no implementation of
 109           the I2C API meaning that any I2C operations will immediately fail
 110           for now.
 111
 112 config SYS_I2C_IMX_LPI2C
 113         bool "NXP i.MX LPI2C driver"
 114         depends on ARCH_MX7ULP
 115         help
 116           Add support for the NXP i.MX LPI2C driver.
 117
 118 config SYS_I2C_MXC
 119         bool "NXP i.MX I2C driver"
 120         depends on MX6
 121         help
 122           Add support for the NXP i.MX I2C driver. This supports upto for bus
 123           channels and operating on standard mode upto 100 kbits/s and fast
 124           mode upto 400 kbits/s.
 125
 126 config SYS_I2C_ROCKCHIP
 127         bool "Rockchip I2C driver"
 128         depends on DM_I2C
 129         help
 130           Add support for the Rockchip I2C driver. This is used with various
 131           Rockchip parts such as RK3126, RK3128, RK3036 and RK3288. All chips
 132           have several I2C ports and all are provided, controled by the
 133           device tree.
 134
 135 config SYS_I2C_SANDBOX
 136         bool "Sandbox I2C driver"
 137         depends on SANDBOX && DM_I2C
 138         help
 139           Enable I2C support for sandbox. This is an emulation of a real I2C
 140           bus. Devices can be attached to the bus using the device tree
 141           which specifies the driver to use.  See sandbox.dts as an example.
 142
 143 config SYS_I2C_S3C24X0
 144         bool "Samsung I2C driver"
 145         depends on ARCH_EXYNOS4 && DM_I2C
 146         help
 147           Support for Samsung I2C controller as Samsung SoCs.
 148
 149 config SYS_I2C_UNIPHIER
 150         bool "UniPhier I2C driver"
 151         depends on ARCH_UNIPHIER && DM_I2C
 152         default y
 153         help
 154           Support for UniPhier I2C controller driver.  This I2C controller
 155           is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
 156
 157 config SYS_I2C_UNIPHIER_F
 158         bool "UniPhier FIFO-builtin I2C driver"
 159         depends on ARCH_UNIPHIER && DM_I2C
 160         default y
 161         help
 162           Support for UniPhier FIFO-builtin I2C controller driver.
 163           This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
 164
 165 config SYS_I2C_MVTWSI
 166         bool "Marvell I2C driver"
 167         depends on DM_I2C
 168         help
 169           Support for Marvell I2C controllers as used on the orion5x and
 170           kirkwood SoC families.
 171
 172 config TEGRA186_BPMP_I2C
 173         bool "Enable Tegra186 BPMP-based I2C driver"
 174         depends on TEGRA186_BPMP
 175         help
 176           Support for Tegra I2C controllers managed by the BPMP (Boot and
 177           Power Management Processor). On Tegra186, some I2C controllers are
 178           directly controlled by the main CPU, whereas others are controlled
 179           by the BPMP, and can only be accessed by the main CPU via IPC
 180           requests to the BPMP. This driver covers the latter case.
 181
 182 source "drivers/i2c/muxes/Kconfig"
 183
 184 endmenu