2 * Copyright (c) 2009 Wind River Systems, Inc.
3 * Tom Rix <Tom.Rix at windriver.com>
5 * SPDX-License-Identifier: GPL-2.0+
7 * twl4030_power_reset_init is derived from code on omapzoom,
8 * git://git.omapzoom.com/repo/u-boot.git
10 * Copyright (C) 2007-2009 Texas Instruments, Inc.
12 * twl4030_power_init is from cpu/omap3/common.c, power_init_r
14 * (C) Copyright 2004-2008
15 * Texas Instruments, <www.ti.com>
18 * Sunil Kumar <sunilsaini05 at gmail.com>
19 * Shashi Ranjan <shashiranjanmca05 at gmail.com>
21 * Derived from Beagle Board and 3430 SDP code by
22 * Richard Woodruff <r-woodruff2 at ti.com>
23 * Syed Mohammed Khasim <khasim at ti.com>
31 void twl4030_power_reset_init(void)
34 if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER
,
35 TWL4030_PM_MASTER_P1_SW_EVENTS
, &val
)) {
36 printf("Error:TWL4030: failed to read the power register\n");
37 printf("Could not initialize hardware reset\n");
39 val
|= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON
;
40 if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER
,
41 TWL4030_PM_MASTER_P1_SW_EVENTS
, val
)) {
42 printf("Error:TWL4030: failed to write the power register\n");
43 printf("Could not initialize hardware reset\n");
49 * Set Device Group and Voltage
51 void twl4030_pmrecv_vsel_cfg(u8 vsel_reg
, u8 vsel_val
,
52 u8 dev_grp
, u8 dev_grp_sel
)
56 /* Select the Voltage */
57 ret
= twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER
, vsel_reg
,
60 printf("Could not write vsel to reg %02x (%d)\n",
65 /* Select the Device Group (enable the supply if dev_grp_sel != 0) */
66 ret
= twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER
, dev_grp
,
69 printf("Could not write grp_sel to reg %02x (%d)\n",
73 void twl4030_power_init(void)
75 /* set VAUX3 to 2.8V */
76 twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX3_DEDICATED
,
77 TWL4030_PM_RECEIVER_VAUX3_VSEL_28
,
78 TWL4030_PM_RECEIVER_VAUX3_DEV_GRP
,
79 TWL4030_PM_RECEIVER_DEV_GRP_P1
);
81 /* set VPLL2 to 1.8V */
82 twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VPLL2_DEDICATED
,
83 TWL4030_PM_RECEIVER_VPLL2_VSEL_18
,
84 TWL4030_PM_RECEIVER_VPLL2_DEV_GRP
,
85 TWL4030_PM_RECEIVER_DEV_GRP_ALL
);
87 /* set VDAC to 1.8V */
88 twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VDAC_DEDICATED
,
89 TWL4030_PM_RECEIVER_VDAC_VSEL_18
,
90 TWL4030_PM_RECEIVER_VDAC_DEV_GRP
,
91 TWL4030_PM_RECEIVER_DEV_GRP_P1
);
94 void twl4030_power_mmc_init(int dev_index
)
97 /* Set VMMC1 to 3.15 Volts */
98 twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC1_DEDICATED
,
99 TWL4030_PM_RECEIVER_VMMC1_VSEL_32
,
100 TWL4030_PM_RECEIVER_VMMC1_DEV_GRP
,
101 TWL4030_PM_RECEIVER_DEV_GRP_P1
);
103 mdelay(100); /* ramp-up delay from Linux code */
104 } else if (dev_index
== 1) {
105 /* Set VMMC2 to 3.15 Volts */
106 twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC2_DEDICATED
,
107 TWL4030_PM_RECEIVER_VMMC2_VSEL_32
,
108 TWL4030_PM_RECEIVER_VMMC2_DEV_GRP
,
109 TWL4030_PM_RECEIVER_DEV_GRP_P1
);
111 mdelay(100); /* ramp-up delay from Linux code */