Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

[people/ms/u-boot.git] / drivers / usb / host / xhci.h

/*
 * USB HOST XHCI Controller
 *
 * Based on xHCI host controller driver in linux-kernel
 * by Sarah Sharp.
 *
 * Copyright (C) 2008 Intel Corp.
 * Author: Sarah Sharp
 *
 * Copyright (C) 2013 Samsung Electronics Co.Ltd
 * Authors: Vivek Gautam <gautam.vivek@samsung.com>
 *          Vikas Sajjan <vikas.sajjan@samsung.com>
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

#ifndef HOST_XHCI_H_
#define HOST_XHCI_H_

#include <asm/cache.h>
#include <asm/io.h>
#include <linux/list.h>
#include <linux/compat.h>

#define MAX_EP_CTX_NUM          31
#define XHCI_ALIGNMENT          64
/* Generic timeout for XHCI events */
#define XHCI_TIMEOUT            5000
/* Max number of USB devices for any host controller - limit in section 6.1 */
#define MAX_HC_SLOTS            256
/* Section 5.3.3 - MaxPorts */
#define MAX_HC_PORTS            127

/* Up to 16 ms to halt an HC */
#define XHCI_MAX_HALT_USEC      (16*1000)

#define XHCI_MAX_RESET_USEC     (250*1000)

/*
 * These bits are Read Only (RO) and should be saved and written to the
 * registers: 0, 3, 10:13, 30
 * connect status, over-current status, port speed, and device removable.
 * connect status and port speed are also sticky - meaning they're in
 * the AUX well and they aren't changed by a hot, warm, or cold reset.
 */
#define XHCI_PORT_RO ((1 << 0) | (1 << 3) | (0xf << 10) | (1 << 30))
/*
 * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit:
 * bits 5:8, 9, 14:15, 25:27
 * link state, port power, port indicator state, "wake on" enable state
 */
#define XHCI_PORT_RWS ((0xf << 5) | (1 << 9) | (0x3 << 14) | (0x7 << 25))
/*
 * These bits are RW; writing a 1 sets the bit, writing a 0 has no effect:
 * bit 4 (port reset)
 */
#define XHCI_PORT_RW1S ((1 << 4))
/*
 * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect:
 * bits 1, 17, 18, 19, 20, 21, 22, 23
 * port enable/disable, and
 * change bits: connect, PED,
 * warm port reset changed (reserved zero for USB 2.0 ports),
 * over-current, reset, link state, and L1 change
 */
#define XHCI_PORT_RW1CS ((1 << 1) | (0x7f << 17))
/*
 * Bit 16 is RW, and writing a '1' to it causes the link state control to be
 * latched in
 */
#define XHCI_PORT_RW ((1 << 16))
/*
 * These bits are Reserved Zero (RsvdZ) and zero should be written to them:
 * bits 2, 24, 28:31
 */
#define XHCI_PORT_RZ ((1 << 2) | (1 << 24) | (0xf << 28))

/*
 * XHCI Register Space.
 */
struct xhci_hccr {
        uint32_t cr_capbase;
        uint32_t cr_hcsparams1;
        uint32_t cr_hcsparams2;
        uint32_t cr_hcsparams3;
        uint32_t cr_hccparams;
        uint32_t cr_dboff;
        uint32_t cr_rtsoff;

/* hc_capbase bitmasks */
/* bits 7:0 - how long is the Capabilities register */
#define HC_LENGTH(p)            XHCI_HC_LENGTH(p)
/* bits 31:16   */
#define HC_VERSION(p)           (((p) >> 16) & 0xffff)

/* HCSPARAMS1 - hcs_params1 - bitmasks */
/* bits 0:7, Max Device Slots */
#define HCS_MAX_SLOTS(p)        (((p) >> 0) & 0xff)
#define HCS_SLOTS_MASK          0xff
/* bits 8:18, Max Interrupters */
#define HCS_MAX_INTRS(p)        (((p) >> 8) & 0x7ff)
/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
#define HCS_MAX_PORTS_SHIFT     24
#define HCS_MAX_PORTS_MASK      (0x7f << HCS_MAX_PORTS_SHIFT)
#define HCS_MAX_PORTS(p)        (((p) >> 24) & 0x7f)

/* HCSPARAMS2 - hcs_params2 - bitmasks */
/* bits 0:3, frames or uframes that SW needs to queue transactions
 * ahead of the HW to meet periodic deadlines */
#define HCS_IST(p)              (((p) >> 0) & 0xf)
/* bits 4:7, max number of Event Ring segments */
#define HCS_ERST_MAX(p)         (((p) >> 4) & 0xf)
/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
/* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */
#define HCS_MAX_SCRATCHPAD(p)   (((p) >> 27) & 0x1f)

/* HCSPARAMS3 - hcs_params3 - bitmasks */
/* bits 0:7, Max U1 to U0 latency for the roothub ports */
#define HCS_U1_LATENCY(p)       (((p) >> 0) & 0xff)
/* bits 16:31, Max U2 to U0 latency for the roothub ports */
#define HCS_U2_LATENCY(p)       (((p) >> 16) & 0xffff)

/* HCCPARAMS - hcc_params - bitmasks */
/* true: HC can use 64-bit address pointers */
#define HCC_64BIT_ADDR(p)       ((p) & (1 << 0))
/* true: HC can do bandwidth negotiation */
#define HCC_BANDWIDTH_NEG(p)    ((p) & (1 << 1))
/* true: HC uses 64-byte Device Context structures
 * FIXME 64-byte context structures aren't supported yet.
 */
#define HCC_64BYTE_CONTEXT(p)   ((p) & (1 << 2))
/* true: HC has port power switches */
#define HCC_PPC(p)              ((p) & (1 << 3))
/* true: HC has port indicators */
#define HCS_INDICATOR(p)        ((p) & (1 << 4))
/* true: HC has Light HC Reset Capability */
#define HCC_LIGHT_RESET(p)      ((p) & (1 << 5))
/* true: HC supports latency tolerance messaging */
#define HCC_LTC(p)              ((p) & (1 << 6))
/* true: no secondary Stream ID Support */
#define HCC_NSS(p)              ((p) & (1 << 7))
/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
#define HCC_MAX_PSA(p)          (1 << ((((p) >> 12) & 0xf) + 1))
/* Extended Capabilities pointer from PCI base - section 5.3.6 */
#define HCC_EXT_CAPS(p)         XHCI_HCC_EXT_CAPS(p)

/* db_off bitmask - bits 0:1 reserved */
#define DBOFF_MASK      (~0x3)

/* run_regs_off bitmask - bits 0:4 reserved */
#define RTSOFF_MASK     (~0x1f)

};

struct xhci_hcor_port_regs {
        volatile uint32_t or_portsc;
        volatile uint32_t or_portpmsc;
        volatile uint32_t or_portli;
        volatile uint32_t reserved_3;
};

struct xhci_hcor {
        volatile uint32_t or_usbcmd;
        volatile uint32_t or_usbsts;
        volatile uint32_t or_pagesize;
        volatile uint32_t reserved_0[2];
        volatile uint32_t or_dnctrl;
        volatile uint64_t or_crcr;
        volatile uint32_t reserved_1[4];
        volatile uint64_t or_dcbaap;
        volatile uint32_t or_config;
        volatile uint32_t reserved_2[241];
        struct xhci_hcor_port_regs portregs[CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS];

        uint32_t reserved_4[CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS * 254];
};

/* USBCMD - USB command - command bitmasks */
/* start/stop HC execution - do not write unless HC is halted*/
#define CMD_RUN         XHCI_CMD_RUN
/* Reset HC - resets internal HC state machine and all registers (except
 * PCI config regs).  HC does NOT drive a USB reset on the downstream ports.
 * The xHCI driver must reinitialize the xHC after setting this bit.
 */
#define CMD_RESET       (1 << 1)
/* Event Interrupt Enable - a '1' allows interrupts from the host controller */
#define CMD_EIE         XHCI_CMD_EIE
/* Host System Error Interrupt Enable - get out-of-band signal for HC errors */
#define CMD_HSEIE       XHCI_CMD_HSEIE
/* bits 4:6 are reserved (and should be preserved on writes). */
/* light reset (port status stays unchanged) - reset completed when this is 0 */
#define CMD_LRESET      (1 << 7)
/* host controller save/restore state. */
#define CMD_CSS         (1 << 8)
#define CMD_CRS         (1 << 9)
/* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
#define CMD_EWE         XHCI_CMD_EWE
/* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root
 * hubs are in U3 (selective suspend), disconnect, disabled, or powered-off.
 * '0' means the xHC can power it off if all ports are in the disconnect,
 * disabled, or powered-off state.
 */
#define CMD_PM_INDEX    (1 << 11)
/* bits 12:31 are reserved (and should be preserved on writes). */

/* USBSTS - USB status - status bitmasks */
/* HC not running - set to 1 when run/stop bit is cleared. */
#define STS_HALT        XHCI_STS_HALT
/* serious error, e.g. PCI parity error.  The HC will clear the run/stop bit. */
#define STS_FATAL       (1 << 2)
/* event interrupt - clear this prior to clearing any IP flags in IR set*/
#define STS_EINT        (1 << 3)
/* port change detect */
#define STS_PORT        (1 << 4)
/* bits 5:7 reserved and zeroed */
/* save state status - '1' means xHC is saving state */
#define STS_SAVE        (1 << 8)
/* restore state status - '1' means xHC is restoring state */
#define STS_RESTORE     (1 << 9)
/* true: save or restore error */
#define STS_SRE         (1 << 10)
/* true: Controller Not Ready to accept doorbell or op reg writes after reset */
#define STS_CNR         XHCI_STS_CNR
/* true: internal Host Controller Error - SW needs to reset and reinitialize */
#define STS_HCE         (1 << 12)
/* bits 13:31 reserved and should be preserved */

/*
 * DNCTRL - Device Notification Control Register - dev_notification bitmasks
 * Generate a device notification event when the HC sees a transaction with a
 * notification type that matches a bit set in this bit field.
 */
#define DEV_NOTE_MASK           (0xffff)
#define ENABLE_DEV_NOTE(x)      (1 << (x))
/* Most of the device notification types should only be used for debug.
 * SW does need to pay attention to function wake notifications.
 */
#define DEV_NOTE_FWAKE          ENABLE_DEV_NOTE(1)

/* CRCR - Command Ring Control Register - cmd_ring bitmasks */
/* bit 0 is the command ring cycle state */
/* stop ring operation after completion of the currently executing command */
#define CMD_RING_PAUSE          (1 << 1)
/* stop ring immediately - abort the currently executing command */
#define CMD_RING_ABORT          (1 << 2)
/* true: command ring is running */
#define CMD_RING_RUNNING        (1 << 3)
/* bits 4:5 reserved and should be preserved */
/* Command Ring pointer - bit mask for the lower 32 bits. */
#define CMD_RING_RSVD_BITS      (0x3f)

/* CONFIG - Configure Register - config_reg bitmasks */
/* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
#define MAX_DEVS(p)     ((p) & 0xff)
/* bits 8:31 - reserved and should be preserved */

/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
/* true: device connected */
#define PORT_CONNECT    (1 << 0)
/* true: port enabled */
#define PORT_PE         (1 << 1)
/* bit 2 reserved and zeroed */
/* true: port has an over-current condition */
#define PORT_OC         (1 << 3)
/* true: port reset signaling asserted */
#define PORT_RESET      (1 << 4)
/* Port Link State - bits 5:8
 * A read gives the current link PM state of the port,
 * a write with Link State Write Strobe set sets the link state.
 */
#define PORT_PLS_MASK   (0xf << 5)
#define XDEV_U0         (0x0 << 5)
#define XDEV_U2         (0x2 << 5)
#define XDEV_U3         (0x3 << 5)
#define XDEV_RESUME     (0xf << 5)
/* true: port has power (see HCC_PPC) */
#define PORT_POWER      (1 << 9)
/* bits 10:13 indicate device speed:
 * 0 - undefined speed - port hasn't be initialized by a reset yet
 * 1 - full speed
 * 2 - low speed
 * 3 - high speed
 * 4 - super speed
 * 5-15 reserved
 */
#define DEV_SPEED_MASK          (0xf << 10)
#define XDEV_FS                 (0x1 << 10)
#define XDEV_LS                 (0x2 << 10)
#define XDEV_HS                 (0x3 << 10)
#define XDEV_SS                 (0x4 << 10)
#define DEV_UNDEFSPEED(p)       (((p) & DEV_SPEED_MASK) == (0x0<<10))
#define DEV_FULLSPEED(p)        (((p) & DEV_SPEED_MASK) == XDEV_FS)
#define DEV_LOWSPEED(p)         (((p) & DEV_SPEED_MASK) == XDEV_LS)
#define DEV_HIGHSPEED(p)        (((p) & DEV_SPEED_MASK) == XDEV_HS)
#define DEV_SUPERSPEED(p)       (((p) & DEV_SPEED_MASK) == XDEV_SS)
/* Bits 20:23 in the Slot Context are the speed for the device */
#define SLOT_SPEED_FS           (XDEV_FS << 10)
#define SLOT_SPEED_LS           (XDEV_LS << 10)
#define SLOT_SPEED_HS           (XDEV_HS << 10)
#define SLOT_SPEED_SS           (XDEV_SS << 10)
/* Port Indicator Control */
#define PORT_LED_OFF    (0 << 14)
#define PORT_LED_AMBER  (1 << 14)
#define PORT_LED_GREEN  (2 << 14)
#define PORT_LED_MASK   (3 << 14)
/* Port Link State Write Strobe - set this when changing link state */
#define PORT_LINK_STROBE        (1 << 16)
/* true: connect status change */
#define PORT_CSC        (1 << 17)
/* true: port enable change */
#define PORT_PEC        (1 << 18)
/* true: warm reset for a USB 3.0 device is done.  A "hot" reset puts the port
 * into an enabled state, and the device into the default state.  A "warm" reset
 * also resets the link, forcing the device through the link training sequence.
 * SW can also look at the Port Reset register to see when warm reset is done.
 */
#define PORT_WRC        (1 << 19)
/* true: over-current change */
#define PORT_OCC        (1 << 20)
/* true: reset change - 1 to 0 transition of PORT_RESET */
#define PORT_RC         (1 << 21)
/* port link status change - set on some port link state transitions:
 *  Transition                          Reason
 *  --------------------------------------------------------------------------
 *  - U3 to Resume              Wakeup signaling from a device
 *  - Resume to Recovery to U0  USB 3.0 device resume
 *  - Resume to U0              USB 2.0 device resume
 *  - U3 to Recovery to U0      Software resume of USB 3.0 device complete
 *  - U3 to U0                  Software resume of USB 2.0 device complete
 *  - U2 to U0                  L1 resume of USB 2.1 device complete
 *  - U0 to U0 (???)            L1 entry rejection by USB 2.1 device
 *  - U0 to disabled            L1 entry error with USB 2.1 device
 *  - Any state to inactive     Error on USB 3.0 port
 */
#define PORT_PLC        (1 << 22)
/* port configure error change - port failed to configure its link partner */
#define PORT_CEC        (1 << 23)
/* bit 24 reserved */
/* wake on connect (enable) */
#define PORT_WKCONN_E   (1 << 25)
/* wake on disconnect (enable) */
#define PORT_WKDISC_E   (1 << 26)
/* wake on over-current (enable) */
#define PORT_WKOC_E     (1 << 27)
/* bits 28:29 reserved */
/* true: device is removable - for USB 3.0 roothub emulation */
#define PORT_DEV_REMOVE (1 << 30)
/* Initiate a warm port reset - complete when PORT_WRC is '1' */
#define PORT_WR         (1 << 31)

/* We mark duplicate entries with -1 */
#define DUPLICATE_ENTRY ((u8)(-1))

/* Port Power Management Status and Control - port_power_base bitmasks */
/* Inactivity timer value for transitions into U1, in microseconds.
 * Timeout can be up to 127us.  0xFF means an infinite timeout.
 */
#define PORT_U1_TIMEOUT(p)      ((p) & 0xff)
/* Inactivity timer value for transitions into U2 */
#define PORT_U2_TIMEOUT(p)      (((p) & 0xff) << 8)
/* Bits 24:31 for port testing */

/* USB2 Protocol PORTSPMSC */
#define PORT_L1S_MASK           7
#define PORT_L1S_SUCCESS        1
#define PORT_RWE                (1 << 3)
#define PORT_HIRD(p)            (((p) & 0xf) << 4)
#define PORT_HIRD_MASK          (0xf << 4)
#define PORT_L1DS(p)            (((p) & 0xff) << 8)
#define PORT_HLE                (1 << 16)

/**
* struct xhci_intr_reg - Interrupt Register Set
* @irq_pending: IMAN - Interrupt Management Register.  Used to enable
*                       interrupts and check for pending interrupts.
* @irq_control: IMOD - Interrupt Moderation Register.
*                       Used to throttle interrupts.
* @erst_size:           Number of segments in the
                        Event Ring Segment Table (ERST).
* @erst_base:           ERST base address.
* @erst_dequeue:        Event ring dequeue pointer.
*
* Each interrupter (defined by a MSI-X vector) has an event ring and an Event
* Ring Segment Table (ERST) associated with it.
* The event ring is comprised of  multiple segments of the same size.
* The HC places events on the ring and  "updates the Cycle bit in the TRBs to
* indicate to software the current  position of the Enqueue Pointer."
* The HCD (Linux) processes those events and  updates the dequeue pointer.
*/
struct xhci_intr_reg {
        volatile __le32 irq_pending;
        volatile __le32 irq_control;
        volatile __le32 erst_size;
        volatile __le32 rsvd;
        volatile __le64 erst_base;
        volatile __le64 erst_dequeue;
};

/* irq_pending bitmasks */
#define ER_IRQ_PENDING(p)       ((p) & 0x1)
/* bits 2:31 need to be preserved */
/* THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR */
#define ER_IRQ_CLEAR(p)         ((p) & 0xfffffffe)
#define ER_IRQ_ENABLE(p)        ((ER_IRQ_CLEAR(p)) | 0x2)
#define ER_IRQ_DISABLE(p)       ((ER_IRQ_CLEAR(p)) & ~(0x2))

/* irq_control bitmasks */
/* Minimum interval between interrupts (in 250ns intervals).  The interval
 * between interrupts will be longer if there are no events on the event ring.
 * Default is 4000 (1 ms).
 */
#define ER_IRQ_INTERVAL_MASK    (0xffff)
/* Counter used to count down the time to the next interrupt - HW use only */
#define ER_IRQ_COUNTER_MASK     (0xffff << 16)

/* erst_size bitmasks */
/* Preserve bits 16:31 of erst_size */
#define ERST_SIZE_MASK          (0xffff << 16)

/* erst_dequeue bitmasks */
/* Dequeue ERST Segment Index (DESI) - Segment number (or alias)
 * where the current dequeue pointer lies.  This is an optional HW hint.
 */
#define ERST_DESI_MASK          (0x7)
/* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by
 * a work queue (or delayed service routine)?
 */
#define ERST_EHB                (1 << 3)
#define ERST_PTR_MASK           (0xf)

/**
 * struct xhci_run_regs
 * @microframe_index:   MFINDEX - current microframe number
 *
 * Section 5.5 Host Controller Runtime Registers:
 * "Software should read and write these registers using only Dword (32 bit)
 * or larger accesses"
 */
struct xhci_run_regs {
        __le32                  microframe_index;
        __le32                  rsvd[7];
        struct xhci_intr_reg    ir_set[128];
};

/**
 * struct doorbell_array
 *
 * Bits  0 -  7: Endpoint target
 * Bits  8 - 15: RsvdZ
 * Bits 16 - 31: Stream ID
 *
 * Section 5.6
 */
struct xhci_doorbell_array {
        volatile __le32 doorbell[256];
};

#define DB_VALUE(ep, stream)    ((((ep) + 1) & 0xff) | ((stream) << 16))
#define DB_VALUE_HOST           0x00000000

/**
 * struct xhci_protocol_caps
 * @revision:           major revision, minor revision, capability ID,
 *                      and next capability pointer.
 * @name_string:        Four ASCII characters to say which spec this xHC
 *                      follows, typically "USB ".
 * @port_info:          Port offset, count, and protocol-defined information.
 */
struct xhci_protocol_caps {
        u32     revision;
        u32     name_string;
        u32     port_info;
};

#define XHCI_EXT_PORT_MAJOR(x)  (((x) >> 24) & 0xff)
#define XHCI_EXT_PORT_OFF(x)    ((x) & 0xff)
#define XHCI_EXT_PORT_COUNT(x)  (((x) >> 8) & 0xff)

/**
 * struct xhci_container_ctx
 * @type: Type of context.  Used to calculated offsets to contained contexts.
 * @size: Size of the context data
 * @bytes: The raw context data given to HW
 * @dma: dma address of the bytes
 *
 * Represents either a Device or Input context.  Holds a pointer to the raw
 * memory used for the context (bytes) and dma address of it (dma).
 */
struct xhci_container_ctx {
        unsigned type;
#define XHCI_CTX_TYPE_DEVICE  0x1
#define XHCI_CTX_TYPE_INPUT   0x2

        int size;
        u8 *bytes;
};

/**
 * struct xhci_slot_ctx
 * @dev_info:   Route string, device speed, hub info, and last valid endpoint
 * @dev_info2:  Max exit latency for device number, root hub port number
 * @tt_info:    tt_info is used to construct split transaction tokens
 * @dev_state:  slot state and device address
 *
 * Slot Context - section 6.2.1.1.  This assumes the HC uses 32-byte context
 * structures.  If the HC uses 64-byte contexts, there is an additional 32 bytes
 * reserved at the end of the slot context for HC internal use.
 */
struct xhci_slot_ctx {
        __le32  dev_info;
        __le32  dev_info2;
        __le32  tt_info;
        __le32  dev_state;
        /* offset 0x10 to 0x1f reserved for HC internal use */
        __le32  reserved[4];
};

/* dev_info bitmasks */
/* Route String - 0:19 */
#define ROUTE_STRING_MASK       (0xfffff)
/* Device speed - values defined by PORTSC Device Speed field - 20:23 */
#define DEV_SPEED               (0xf << 20)
/* bit 24 reserved */
/* Is this LS/FS device connected through a HS hub? - bit 25 */
#define DEV_MTT                 (0x1 << 25)
/* Set if the device is a hub - bit 26 */
#define DEV_HUB                 (0x1 << 26)
/* Index of the last valid endpoint context in this device context - 27:31 */
#define LAST_CTX_MASK           (0x1f << 27)
#define LAST_CTX(p)             ((p) << 27)
#define LAST_CTX_TO_EP_NUM(p)   (((p) >> 27) - 1)
#define SLOT_FLAG               (1 << 0)
#define EP0_FLAG                (1 << 1)

/* dev_info2 bitmasks */
/* Max Exit Latency (ms) - worst case time to wake up all links in dev path */
#define MAX_EXIT                        (0xffff)
/* Root hub port number that is needed to access the USB device */
#define ROOT_HUB_PORT(p)                (((p) & 0xff) << 16)
#define ROOT_HUB_PORT_MASK              (0xff)
#define ROOT_HUB_PORT_SHIFT             (16)
#define DEVINFO_TO_ROOT_HUB_PORT(p)     (((p) >> 16) & 0xff)
/* Maximum number of ports under a hub device */
#define XHCI_MAX_PORTS(p)               (((p) & 0xff) << 24)

/* tt_info bitmasks */
/*
 * TT Hub Slot ID - for low or full speed devices attached to a high-speed hub
 * The Slot ID of the hub that isolates the high speed signaling from
 * this low or full-speed device.  '0' if attached to root hub port.
 */
#define TT_SLOT                 (0xff)
/*
 * The number of the downstream facing port of the high-speed hub
 * '0' if the device is not low or full speed.
 */
#define TT_PORT                 (0xff << 8)
#define TT_THINK_TIME(p)        (((p) & 0x3) << 16)

/* dev_state bitmasks */
/* USB device address - assigned by the HC */
#define DEV_ADDR_MASK   (0xff)
/* bits 8:26 reserved */
/* Slot state */
#define SLOT_STATE              (0x1f << 27)
#define GET_SLOT_STATE(p)       (((p) & (0x1f << 27)) >> 27)

#define SLOT_STATE_DISABLED     0
#define SLOT_STATE_ENABLED      SLOT_STATE_DISABLED
#define SLOT_STATE_DEFAULT      1
#define SLOT_STATE_ADDRESSED    2
#define SLOT_STATE_CONFIGURED   3

/**
 * struct xhci_ep_ctx
 * @ep_info:    endpoint state, streams, mult, and interval information.
 * @ep_info2:   information on endpoint type, max packet size, max burst size,
 *              error count, and whether the HC will force an event for all
 *              transactions.
 * @deq:        64-bit ring dequeue pointer address.  If the endpoint only
 *              defines one stream, this points to the endpoint transfer ring.
 *              Otherwise, it points to a stream context array, which has a
 *              ring pointer for each flow.
 * @tx_info:
 *              Average TRB lengths for the endpoint ring and
 *              max payload within an Endpoint Service Interval Time (ESIT).
 *
 * Endpoint Context - section 6.2.1.2.This assumes the HC uses 32-byte context
 * structures.If the HC uses 64-byte contexts, there is an additional 32 bytes
 * reserved at the end of the endpoint context for HC internal use.
 */
struct xhci_ep_ctx {
        __le32  ep_info;
        __le32  ep_info2;
        __le64  deq;
        __le32  tx_info;
        /* offset 0x14 - 0x1f reserved for HC internal use */
        __le32  reserved[3];
};

/* ep_info bitmasks */
/*
 * Endpoint State - bits 0:2
 * 0 - disabled
 * 1 - running
 * 2 - halted due to halt condition - ok to manipulate endpoint ring
 * 3 - stopped
 * 4 - TRB error
 * 5-7 - reserved
 */
#define EP_STATE_MASK           (0xf)
#define EP_STATE_DISABLED       0
#define EP_STATE_RUNNING        1
#define EP_STATE_HALTED         2
#define EP_STATE_STOPPED        3
#define EP_STATE_ERROR          4
/* Mult - Max number of burtst within an interval, in EP companion desc. */
#define EP_MULT(p)              (((p) & 0x3) << 8)
#define CTX_TO_EP_MULT(p)       (((p) >> 8) & 0x3)
/* bits 10:14 are Max Primary Streams */
/* bit 15 is Linear Stream Array */
/* Interval - period between requests to an endpoint - 125u increments. */
#define EP_INTERVAL(p)                  (((p) & 0xff) << 16)
#define EP_INTERVAL_TO_UFRAMES(p)       (1 << (((p) >> 16) & 0xff))
#define CTX_TO_EP_INTERVAL(p)           (((p) >> 16) & 0xff)
#define EP_MAXPSTREAMS_MASK             (0x1f << 10)
#define EP_MAXPSTREAMS(p)               (((p) << 10) & EP_MAXPSTREAMS_MASK)
/* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */
#define EP_HAS_LSA                      (1 << 15)

/* ep_info2 bitmasks */
/*
 * Force Event - generate transfer events for all TRBs for this endpoint
 * This will tell the HC to ignore the IOC and ISP flags (for debugging only).
 */
#define FORCE_EVENT             (0x1)
#define ERROR_COUNT(p)          (((p) & 0x3) << 1)
#define ERROR_COUNT_SHIFT       (1)
#define ERROR_COUNT_MASK        (0x3)
#define CTX_TO_EP_TYPE(p)       (((p) >> 3) & 0x7)
#define EP_TYPE(p)              ((p) << 3)
#define EP_TYPE_SHIFT           (3)
#define ISOC_OUT_EP             1
#define BULK_OUT_EP             2
#define INT_OUT_EP              3
#define CTRL_EP                 4
#define ISOC_IN_EP              5
#define BULK_IN_EP              6
#define INT_IN_EP               7
/* bit 6 reserved */
/* bit 7 is Host Initiate Disable - for disabling stream selection */
#define MAX_BURST(p)            (((p)&0xff) << 8)
#define MAX_BURST_MASK          (0xff)
#define MAX_BURST_SHIFT         (8)
#define CTX_TO_MAX_BURST(p)     (((p) >> 8) & 0xff)
#define MAX_PACKET(p)           (((p)&0xffff) << 16)
#define MAX_PACKET_MASK         (0xffff)
#define MAX_PACKET_DECODED(p)   (((p) >> 16) & 0xffff)
#define MAX_PACKET_SHIFT        (16)

/* Get max packet size from ep desc. Bit 10..0 specify the max packet size.
 * USB2.0 spec 9.6.6.
 */
#define GET_MAX_PACKET(p)       ((p) & 0x7ff)

/* tx_info bitmasks */
#define AVG_TRB_LENGTH_FOR_EP(p)        ((p) & 0xffff)
#define MAX_ESIT_PAYLOAD_FOR_EP(p)      (((p) & 0xffff) << 16)
#define CTX_TO_MAX_ESIT_PAYLOAD(p)      (((p) >> 16) & 0xffff)

/* deq bitmasks */
#define EP_CTX_CYCLE_MASK               (1 << 0)


/**
 * struct xhci_input_control_context
 * Input control context; see section 6.2.5.
 *
 * @drop_context:       set the bit of the endpoint context you want to disable
 * @add_context:        set the bit of the endpoint context you want to enable
 */
struct xhci_input_control_ctx {
        volatile __le32 drop_flags;
        volatile __le32 add_flags;
        __le32  rsvd2[6];
};


/**
 * struct xhci_device_context_array
 * @dev_context_ptr     array of 64-bit DMA addresses for device contexts
 */
struct xhci_device_context_array {
        /* 64-bit device addresses; we only write 32-bit addresses */
        __le64                  dev_context_ptrs[MAX_HC_SLOTS];
};
/* TODO: write function to set the 64-bit device DMA address */
/*
 * TODO: change this to be dynamically sized at HC mem init time since the HC
 * might not be able to handle the maximum number of devices possible.
 */


struct xhci_transfer_event {
        /* 64-bit buffer address, or immediate data */
        __le64  buffer;
        __le32  transfer_len;
        /* This field is interpreted differently based on the type of TRB */
        volatile __le32 flags;
};

/* Transfer event TRB length bit mask */
/* bits 0:23 */
#define EVENT_TRB_LEN(p)        ((p) & 0xffffff)

/** Transfer Event bit fields **/
#define TRB_TO_EP_ID(p)         (((p) >> 16) & 0x1f)

/* Completion Code - only applicable for some types of TRBs */
#define COMP_CODE_MASK          (0xff << 24)
#define COMP_CODE_SHIFT         (24)
#define GET_COMP_CODE(p)        (((p) & COMP_CODE_MASK) >> 24)

typedef enum {
        COMP_SUCCESS = 1,
        /* Data Buffer Error */
        COMP_DB_ERR, /* 2 */
        /* Babble Detected Error */
        COMP_BABBLE, /* 3 */
        /* USB Transaction Error */
        COMP_TX_ERR, /* 4 */
        /* TRB Error - some TRB field is invalid */
        COMP_TRB_ERR, /* 5 */
        /* Stall Error - USB device is stalled */
        COMP_STALL, /* 6 */
        /* Resource Error - HC doesn't have memory for that device configuration */
        COMP_ENOMEM, /* 7 */
        /* Bandwidth Error - not enough room in schedule for this dev config */
        COMP_BW_ERR, /* 8 */
        /* No Slots Available Error - HC ran out of device slots */
        COMP_ENOSLOTS, /* 9 */
        /* Invalid Stream Type Error */
        COMP_STREAM_ERR, /* 10 */
        /* Slot Not Enabled Error - doorbell rung for disabled device slot */
        COMP_EBADSLT, /* 11 */
        /* Endpoint Not Enabled Error */
        COMP_EBADEP,/* 12 */
        /* Short Packet */
        COMP_SHORT_TX, /* 13 */
        /* Ring Underrun - doorbell rung for an empty isoc OUT ep ring */
        COMP_UNDERRUN, /* 14 */
        /* Ring Overrun - isoc IN ep ring is empty when ep is scheduled to RX */
        COMP_OVERRUN, /* 15 */
        /* Virtual Function Event Ring Full Error */
        COMP_VF_FULL, /* 16 */
        /* Parameter Error - Context parameter is invalid */
        COMP_EINVAL, /* 17 */
        /* Bandwidth Overrun Error - isoc ep exceeded its allocated bandwidth */
        COMP_BW_OVER,/* 18 */
        /* Context State Error - illegal context state transition requested */
        COMP_CTX_STATE,/* 19 */
        /* No Ping Response Error - HC didn't get PING_RESPONSE in time to TX */
        COMP_PING_ERR,/* 20 */
        /* Event Ring is full */
        COMP_ER_FULL,/* 21 */
        /* Incompatible Device Error */
        COMP_DEV_ERR,/* 22 */
        /* Missed Service Error - HC couldn't service an isoc ep within interval */
        COMP_MISSED_INT,/* 23 */
        /* Successfully stopped command ring */
        COMP_CMD_STOP, /* 24 */
        /* Successfully aborted current command and stopped command ring */
        COMP_CMD_ABORT, /* 25 */
        /* Stopped - transfer was terminated by a stop endpoint command */
        COMP_STOP,/* 26 */
        /* Same as COMP_EP_STOPPED, but the transferred length in the event
         * is invalid */
        COMP_STOP_INVAL, /* 27*/
        /* Control Abort Error - Debug Capability - control pipe aborted */
        COMP_DBG_ABORT, /* 28 */
        /* Max Exit Latency Too Large Error */
        COMP_MEL_ERR,/* 29 */
        /* TRB type 30 reserved */
        /* Isoc Buffer Overrun - an isoc IN ep sent more data than could fit in TD */
        COMP_BUFF_OVER = 31,
        /* Event Lost Error - xHC has an "internal event overrun condition" */
        COMP_ISSUES, /* 32 */
        /* Undefined Error - reported when other error codes don't apply */
        COMP_UNKNOWN, /* 33 */
        /* Invalid Stream ID Error */
        COMP_STRID_ERR, /* 34 */
        /* Secondary Bandwidth Error - may be returned by a Configure Endpoint cmd */
        COMP_2ND_BW_ERR, /* 35 */
        /* Split Transaction Error */
        COMP_SPLIT_ERR /* 36 */

} xhci_comp_code;

struct xhci_link_trb {
        /* 64-bit segment pointer*/
        volatile __le64 segment_ptr;
        volatile __le32 intr_target;
        volatile __le32 control;
};

/* control bitfields */
#define LINK_TOGGLE (0x1 << 1)

/* Command completion event TRB */
struct xhci_event_cmd {
        /* Pointer to command TRB, or the value passed by the event data trb */
        volatile __le64 cmd_trb;
        volatile __le32 status;
        volatile __le32 flags;
};

/* flags bitmasks */
/* bits 16:23 are the virtual function ID */
/* bits 24:31 are the slot ID */
#define TRB_TO_SLOT_ID(p)               (((p) & (0xff << 24)) >> 24)
#define TRB_TO_SLOT_ID_SHIFT            (24)
#define TRB_TO_SLOT_ID_MASK             (0xff << TRB_TO_SLOT_ID_SHIFT)
#define SLOT_ID_FOR_TRB(p)              (((p) & 0xff) << 24)
#define SLOT_ID_FOR_TRB_MASK            (0xff)
#define SLOT_ID_FOR_TRB_SHIFT           (24)

/* Stop Endpoint TRB - ep_index to endpoint ID for this TRB */
#define TRB_TO_EP_INDEX(p)              ((((p) & (0x1f << 16)) >> 16) - 1)
#define EP_ID_FOR_TRB(p)                ((((p) + 1) & 0x1f) << 16)

#define SUSPEND_PORT_FOR_TRB(p)         (((p) & 1) << 23)
#define TRB_TO_SUSPEND_PORT(p)          (((p) & (1 << 23)) >> 23)
#define LAST_EP_INDEX                   30

/* Set TR Dequeue Pointer command TRB fields */
#define TRB_TO_STREAM_ID(p)             ((((p) & (0xffff << 16)) >> 16))
#define STREAM_ID_FOR_TRB(p)            ((((p)) & 0xffff) << 16)


/* Port Status Change Event TRB fields */
/* Port ID - bits 31:24 */
#define GET_PORT_ID(p)                  (((p) & (0xff << 24)) >> 24)
#define PORT_ID_SHIFT                   (24)
#define PORT_ID_MASK                    (0xff << PORT_ID_SHIFT)

/* Normal TRB fields */
/* transfer_len bitmasks - bits 0:16 */
#define TRB_LEN(p)                      ((p) & 0x1ffff)
#define TRB_LEN_MASK                    (0x1ffff)
/* Interrupter Target - which MSI-X vector to target the completion event at */
#define TRB_INTR_TARGET_SHIFT           (22)
#define TRB_INTR_TARGET_MASK            (0x3ff)
#define TRB_INTR_TARGET(p)              (((p) & 0x3ff) << 22)
#define GET_INTR_TARGET(p)              (((p) >> 22) & 0x3ff)
#define TRB_TBC(p)                      (((p) & 0x3) << 7)
#define TRB_TLBPC(p)                    (((p) & 0xf) << 16)

/* Cycle bit - indicates TRB ownership by HC or HCD */
#define TRB_CYCLE               (1<<0)
/*
 * Force next event data TRB to be evaluated before task switch.
 * Used to pass OS data back after a TD completes.
 */
#define TRB_ENT                 (1<<1)
/* Interrupt on short packet */
#define TRB_ISP                 (1<<2)
/* Set PCIe no snoop attribute */
#define TRB_NO_SNOOP            (1<<3)
/* Chain multiple TRBs into a TD */
#define TRB_CHAIN               (1<<4)
/* Interrupt on completion */
#define TRB_IOC                 (1<<5)
/* The buffer pointer contains immediate data */
#define TRB_IDT                 (1<<6)

/* Block Event Interrupt */
#define TRB_BEI                 (1<<9)

/* Control transfer TRB specific fields */
#define TRB_DIR_IN              (1<<16)
#define TRB_TX_TYPE(p)          ((p) << 16)
#define TRB_TX_TYPE_SHIFT       (16)
#define TRB_DATA_OUT            2
#define TRB_DATA_IN             3

/* Isochronous TRB specific fields */
#define TRB_SIA                 (1 << 31)

struct xhci_generic_trb {
        volatile __le32 field[4];
};

union xhci_trb {
        struct xhci_link_trb            link;
        struct xhci_transfer_event      trans_event;
        struct xhci_event_cmd           event_cmd;
        struct xhci_generic_trb         generic;
};

/* TRB bit mask */
#define TRB_TYPE_BITMASK        (0xfc00)
#define TRB_TYPE(p)             ((p) << 10)
#define TRB_TYPE_SHIFT          (10)
#define TRB_FIELD_TO_TYPE(p)    (((p) & TRB_TYPE_BITMASK) >> 10)

/* TRB type IDs */
typedef enum {
        /* bulk, interrupt, isoc scatter/gather, and control data stage */
        TRB_NORMAL = 1,
        /* setup stage for control transfers */
        TRB_SETUP, /* 2 */
        /* data stage for control transfers */
        TRB_DATA, /* 3 */
        /* status stage for control transfers */
        TRB_STATUS, /* 4 */
        /* isoc transfers */
        TRB_ISOC, /* 5 */
        /* TRB for linking ring segments */
        TRB_LINK, /* 6 */
        /* TRB for EVENT DATA */
        TRB_EVENT_DATA, /* 7 */
        /* Transfer Ring No-op (not for the command ring) */
        TRB_TR_NOOP, /* 8 */
        /* Command TRBs */
        /* Enable Slot Command */
        TRB_ENABLE_SLOT, /* 9 */
        /* Disable Slot Command */
        TRB_DISABLE_SLOT, /* 10 */
        /* Address Device Command */
        TRB_ADDR_DEV, /* 11 */
        /* Configure Endpoint Command */
        TRB_CONFIG_EP, /* 12 */
        /* Evaluate Context Command */
        TRB_EVAL_CONTEXT, /* 13 */
        /* Reset Endpoint Command */
        TRB_RESET_EP, /* 14 */
        /* Stop Transfer Ring Command */
        TRB_STOP_RING, /* 15 */
        /* Set Transfer Ring Dequeue Pointer Command */
        TRB_SET_DEQ, /* 16 */
        /* Reset Device Command */
        TRB_RESET_DEV, /* 17 */
        /* Force Event Command (opt) */
        TRB_FORCE_EVENT, /* 18 */
        /* Negotiate Bandwidth Command (opt) */
        TRB_NEG_BANDWIDTH, /* 19 */
        /* Set Latency Tolerance Value Command (opt) */
        TRB_SET_LT, /* 20 */
        /* Get port bandwidth Command */
        TRB_GET_BW, /* 21 */
        /* Force Header Command - generate a transaction or link management packet */
        TRB_FORCE_HEADER, /* 22 */
        /* No-op Command - not for transfer rings */
        TRB_CMD_NOOP, /* 23 */
        /* TRB IDs 24-31 reserved */
        /* Event TRBS */
        /* Transfer Event */
        TRB_TRANSFER = 32,
        /* Command Completion Event */
        TRB_COMPLETION, /* 33 */
        /* Port Status Change Event */
        TRB_PORT_STATUS, /* 34 */
        /* Bandwidth Request Event (opt) */
        TRB_BANDWIDTH_EVENT, /* 35 */
        /* Doorbell Event (opt) */
        TRB_DOORBELL, /* 36 */
        /* Host Controller Event */
        TRB_HC_EVENT, /* 37 */
        /* Device Notification Event - device sent function wake notification */
        TRB_DEV_NOTE, /* 38 */
        /* MFINDEX Wrap Event - microframe counter wrapped */
        TRB_MFINDEX_WRAP, /* 39 */
        /* TRB IDs 40-47 reserved, 48-63 is vendor-defined */
        /* Nec vendor-specific command completion event. */
        TRB_NEC_CMD_COMP = 48, /* 48 */
        /* Get NEC firmware revision. */
        TRB_NEC_GET_FW, /* 49 */
} trb_type;

#define TRB_TYPE_LINK(x)        (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK))
/* Above, but for __le32 types -- can avoid work by swapping constants: */
#define TRB_TYPE_LINK_LE32(x)   (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
                                 cpu_to_le32(TRB_TYPE(TRB_LINK)))
#define TRB_TYPE_NOOP_LE32(x)   (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
                                 cpu_to_le32(TRB_TYPE(TRB_TR_NOOP)))

/*
 * TRBS_PER_SEGMENT must be a multiple of 4,
 * since the command ring is 64-byte aligned.
 * It must also be greater than 16.
 */
#define TRBS_PER_SEGMENT        64
/* Allow two commands + a link TRB, along with any reserved command TRBs */
#define MAX_RSVD_CMD_TRBS       (TRBS_PER_SEGMENT - 3)
#define SEGMENT_SIZE            (TRBS_PER_SEGMENT*16)
/* SEGMENT_SHIFT should be log2(SEGMENT_SIZE).
 * Change this if you change TRBS_PER_SEGMENT!
 */
#define SEGMENT_SHIFT           10
/* TRB buffer pointers can't cross 64KB boundaries */
#define TRB_MAX_BUFF_SHIFT      16
#define TRB_MAX_BUFF_SIZE       (1 << TRB_MAX_BUFF_SHIFT)

struct xhci_segment {
        union xhci_trb          *trbs;
        /* private to HCD */
        struct xhci_segment     *next;
};

struct xhci_ring {
        struct xhci_segment     *first_seg;
        union  xhci_trb         *enqueue;
        struct xhci_segment     *enq_seg;
        union  xhci_trb         *dequeue;
        struct xhci_segment     *deq_seg;
        /*
         * Write the cycle state into the TRB cycle field to give ownership of
         * the TRB to the host controller (if we are the producer), or to check
         * if we own the TRB (if we are the consumer).  See section 4.9.1.
         */
        volatile u32            cycle_state;
        unsigned int            num_segs;
};

struct xhci_erst_entry {
        /* 64-bit event ring segment address */
        __le64  seg_addr;
        __le32  seg_size;
        /* Set to zero */
        __le32  rsvd;
};

struct xhci_erst {
        struct xhci_erst_entry  *entries;
        unsigned int            num_entries;
        /* Num entries the ERST can contain */
        unsigned int            erst_size;
};

/*
 * Each segment table entry is 4*32bits long.  1K seems like an ok size:
 * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
 * meaning 64 ring segments.
 * Initial allocated size of the ERST, in number of entries */
#define ERST_NUM_SEGS   3
/* Initial number of event segment rings allocated */
#define ERST_ENTRIES    3
/* Initial allocated size of the ERST, in number of entries */
#define ERST_SIZE       64
/* Poll every 60 seconds */
#define POLL_TIMEOUT    60
/* Stop endpoint command timeout (secs) for URB cancellation watchdog timer */
#define XHCI_STOP_EP_CMD_TIMEOUT        5
/* XXX: Make these module parameters */

struct xhci_virt_ep {
        struct xhci_ring                *ring;
        unsigned int                    ep_state;
#define SET_DEQ_PENDING         (1 << 0)
#define EP_HALTED               (1 << 1)        /* For stall handling */
#define EP_HALT_PENDING         (1 << 2)        /* For URB cancellation */
/* Transitioning the endpoint to using streams, don't enqueue URBs */
#define EP_GETTING_STREAMS      (1 << 3)
#define EP_HAS_STREAMS          (1 << 4)
/* Transitioning the endpoint to not using streams, don't enqueue URBs */
#define EP_GETTING_NO_STREAMS   (1 << 5)
};

#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)

struct xhci_virt_device {
        struct usb_device               *udev;
        /*
         * Commands to the hardware are passed an "input context" that
         * tells the hardware what to change in its data structures.
         * The hardware will return changes in an "output context" that
         * software must allocate for the hardware.  We need to keep
         * track of input and output contexts separately because
         * these commands might fail and we don't trust the hardware.
         */
        struct xhci_container_ctx       *out_ctx;
        /* Used for addressing devices and configuration changes */
        struct xhci_container_ctx       *in_ctx;
        /* Rings saved to ensure old alt settings can be re-instated */
#define XHCI_MAX_RINGS_CACHED   31
        struct xhci_virt_ep             eps[31];
};

/* TODO: copied from ehci.h - can be refactored? */
/* xHCI spec says all registers are little endian */
static inline unsigned int xhci_readl(uint32_t volatile *regs)
{
        return readl(regs);
}

static inline void xhci_writel(uint32_t volatile *regs, const unsigned int val)
{
        writel(val, regs);
}

/*
 * Registers should always be accessed with double word or quad word accesses.
 * Some xHCI implementations may support 64-bit address pointers.  Registers
 * with 64-bit address pointers should be written to with dword accesses by
 * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
 * xHCI implementations that do not support 64-bit address pointers will ignore
 * the high dword, and write order is irrelevant.
 */
static inline u64 xhci_readq(__le64 volatile *regs)
{
        __u32 *ptr = (__u32 *)regs;
        u64 val_lo = readl(ptr);
        u64 val_hi = readl(ptr + 1);
        return val_lo + (val_hi << 32);
}

static inline void xhci_writeq(__le64 volatile *regs, const u64 val)
{
        __u32 *ptr = (__u32 *)regs;
        u32 val_lo = lower_32_bits(val);
        /* FIXME */
        u32 val_hi = upper_32_bits(val);
        writel(val_lo, ptr);
        writel(val_hi, ptr + 1);
}

int xhci_hcd_init(int index, struct xhci_hccr **ret_hccr,
                                        struct xhci_hcor **ret_hcor);
void xhci_hcd_stop(int index);


/*************************************************************
        EXTENDED CAPABILITY DEFINITIONS
*************************************************************/
/* Up to 16 ms to halt an HC */
#define XHCI_MAX_HALT_USEC      (16*1000)
/* HC not running - set to 1 when run/stop bit is cleared. */
#define XHCI_STS_HALT           (1 << 0)

/* HCCPARAMS offset from PCI base address */
#define XHCI_HCC_PARAMS_OFFSET  0x10
/* HCCPARAMS contains the first extended capability pointer */
#define XHCI_HCC_EXT_CAPS(p)    (((p)>>16)&0xffff)

/* Command and Status registers offset from the Operational Registers address */
#define XHCI_CMD_OFFSET         0x00
#define XHCI_STS_OFFSET         0x04

#define XHCI_MAX_EXT_CAPS               50

/* Capability Register */
/* bits 7:0 - how long is the Capabilities register */
#define XHCI_HC_LENGTH(p)       (((p) >> 00) & 0x00ff)

/* Extended capability register fields */
#define XHCI_EXT_CAPS_ID(p)     (((p) >> 0) & 0xff)
#define XHCI_EXT_CAPS_NEXT(p)   (((p) >> 8) & 0xff)
#define XHCI_EXT_CAPS_VAL(p)    ((p) >> 16)
/* Extended capability IDs - ID 0 reserved */
#define XHCI_EXT_CAPS_LEGACY    1
#define XHCI_EXT_CAPS_PROTOCOL  2
#define XHCI_EXT_CAPS_PM        3
#define XHCI_EXT_CAPS_VIRT      4
#define XHCI_EXT_CAPS_ROUTE     5
/* IDs 6-9 reserved */
#define XHCI_EXT_CAPS_DEBUG     10
/* USB Legacy Support Capability - section 7.1.1 */
#define XHCI_HC_BIOS_OWNED      (1 << 16)
#define XHCI_HC_OS_OWNED        (1 << 24)

/* USB Legacy Support Capability - section 7.1.1 */
/* Add this offset, plus the value of xECP in HCCPARAMS to the base address */
#define XHCI_LEGACY_SUPPORT_OFFSET      (0x00)

/* USB Legacy Support Control and Status Register  - section 7.1.2 */
/* Add this offset, plus the value of xECP in HCCPARAMS to the base address */
#define XHCI_LEGACY_CONTROL_OFFSET      (0x04)
/* bits 1:2, 5:12, and 17:19 need to be preserved; bits 21:28 should be zero */
#define XHCI_LEGACY_DISABLE_SMI         ((0x3 << 1) + (0xff << 5) + (0x7 << 17))

/* USB 2.0 xHCI 0.96 L1C capability - section 7.2.2.1.3.2 */
#define XHCI_L1C               (1 << 16)

/* USB 2.0 xHCI 1.0 hardware LMP capability - section 7.2.2.1.3.2 */
#define XHCI_HLC               (1 << 19)

/* command register values to disable interrupts and halt the HC */
/* start/stop HC execution - do not write unless HC is halted*/
#define XHCI_CMD_RUN            (1 << 0)
/* Event Interrupt Enable - get irq when EINT bit is set in USBSTS register */
#define XHCI_CMD_EIE            (1 << 2)
/* Host System Error Interrupt Enable - get irq when HSEIE bit set in USBSTS */
#define XHCI_CMD_HSEIE          (1 << 3)
/* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
#define XHCI_CMD_EWE            (1 << 10)

#define XHCI_IRQS               (XHCI_CMD_EIE | XHCI_CMD_HSEIE | XHCI_CMD_EWE)

/* true: Controller Not Ready to accept doorbell or op reg writes after reset */
#define XHCI_STS_CNR            (1 << 11)

struct xhci_ctrl {
        struct xhci_hccr *hccr; /* R/O registers, not need for volatile */
        struct xhci_hcor *hcor;
        struct xhci_doorbell_array *dba;
        struct xhci_run_regs *run_regs;
        struct xhci_device_context_array *dcbaa         \
                        __attribute__ ((aligned(ARCH_DMA_MINALIGN)));
        struct xhci_ring *event_ring;
        struct xhci_ring *cmd_ring;
        struct xhci_ring *transfer_ring;
        struct xhci_segment *seg;
        struct xhci_intr_reg *ir_set;
        struct xhci_erst erst;
        struct xhci_erst_entry entry[ERST_NUM_SEGS];
        struct xhci_virt_device *devs[MAX_HC_SLOTS];
        int rootdev;
};

unsigned long trb_addr(struct xhci_segment *seg, union xhci_trb *trb);
struct xhci_input_control_ctx
                *xhci_get_input_control_ctx(struct xhci_container_ctx *ctx);
struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_ctrl *ctrl,
                                        struct xhci_container_ctx *ctx);
struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_ctrl *ctrl,
                                    struct xhci_container_ctx *ctx,
                                    unsigned int ep_index);
void xhci_endpoint_copy(struct xhci_ctrl *ctrl,
                        struct xhci_container_ctx *in_ctx,
                        struct xhci_container_ctx *out_ctx,
                        unsigned int ep_index);
void xhci_slot_copy(struct xhci_ctrl *ctrl,
                    struct xhci_container_ctx *in_ctx,
                    struct xhci_container_ctx *out_ctx);
void xhci_setup_addressable_virt_dev(struct usb_device *udev);
void xhci_queue_command(struct xhci_ctrl *ctrl, u8 *ptr,
                        u32 slot_id, u32 ep_index, trb_type cmd);
void xhci_acknowledge_event(struct xhci_ctrl *ctrl);
union xhci_trb *xhci_wait_for_event(struct xhci_ctrl *ctrl, trb_type expected);
int xhci_bulk_tx(struct usb_device *udev, unsigned long pipe,
                 int length, void *buffer);
int xhci_ctrl_tx(struct usb_device *udev, unsigned long pipe,
                 struct devrequest *req, int length, void *buffer);
int xhci_check_maxpacket(struct usb_device *udev);
void xhci_flush_cache(uint32_t addr, u32 type_len);
void xhci_inval_cache(uint32_t addr, u32 type_len);
void xhci_cleanup(struct xhci_ctrl *ctrl);
struct xhci_ring *xhci_ring_alloc(unsigned int num_segs, bool link_trbs);
int xhci_alloc_virt_device(struct usb_device *udev);
int xhci_mem_init(struct xhci_ctrl *ctrl, struct xhci_hccr *hccr,
                  struct xhci_hcor *hcor);

#endif /* HOST_XHCI_H_ */