include/configs/BSC9131RDB.h

   1 /*
   2  * Copyright 2011-2012 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * BSC9131 RDB board configuration file
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 #define CONFIG_SYS_GENERIC_BOARD
  15 #define CONFIG_DISPLAY_BOARDINFO
  16
  17 #ifdef CONFIG_BSC9131RDB
  18 #define CONFIG_BSC9131
  19 #define CONFIG_NAND_FSL_IFC
  20 #endif
  21
  22 #ifdef CONFIG_SPIFLASH
  23 #define CONFIG_RAMBOOT_SPIFLASH
  24 #define CONFIG_SYS_RAMBOOT
  25 #define CONFIG_SYS_EXTRA_ENV_RELOC
  26 #define CONFIG_SYS_TEXT_BASE            0x11000000
  27 #define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
  28 #endif
  29
  30 #ifdef CONFIG_NAND
  31 #define CONFIG_SPL_INIT_MINIMAL
  32 #define CONFIG_SPL_SERIAL_SUPPORT
  33 #define CONFIG_SPL_NAND_SUPPORT
  34 #define CONFIG_SPL_NAND_BOOT
  35 #define CONFIG_SPL_FLUSH_IMAGE
  36 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  37
  38 #define CONFIG_SYS_TEXT_BASE            0x00201000
  39 #define CONFIG_SPL_TEXT_BASE            0xFFFFE000
  40 #define CONFIG_SPL_MAX_SIZE             8192
  41 #define CONFIG_SPL_RELOC_TEXT_BASE      0x00100000
  42 #define CONFIG_SPL_RELOC_STACK          0x00100000
  43 #define CONFIG_SYS_NAND_U_BOOT_SIZE     ((768 << 10) - 0x2000)
  44 #define CONFIG_SYS_NAND_U_BOOT_DST      (0x00200000 - CONFIG_SPL_MAX_SIZE)
  45 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  46 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0
  47 #define CONFIG_SYS_LDSCRIPT     "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  48 #endif
  49
  50 #ifdef CONFIG_SPL_BUILD
  51 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
  52 #else
  53 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  54 #endif
  55
  56
  57 /* High Level Configuration Options */
  58 #define CONFIG_BOOKE                    /* BOOKE */
  59 #define CONFIG_E500                     /* BOOKE e500 family */
  60 #define CONFIG_FSL_IFC                  /* Enable IFC Support */
  61 #define CONFIG_FSL_CAAM                 /* Enable SEC/CAAM */
  62
  63 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  64 #define CONFIG_TSEC_ENET
  65 #define CONFIG_ENV_OVERWRITE
  66
  67 #define CONFIG_DDR_CLK_FREQ     66666666 /* DDRCLK on 9131 RDB */
  68 #if defined(CONFIG_SYS_CLK_100)
  69 #define CONFIG_SYS_CLK_FREQ    100000000 /* SYSCLK for 9131 RDB */
  70 #else
  71 #define CONFIG_SYS_CLK_FREQ     66666666 /* SYSCLK for 9131 RDB */
  72 #endif
  73
  74 #define CONFIG_HWCONFIG
  75 /*
  76  * These can be toggled for performance analysis, otherwise use default.
  77  */
  78 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  79 #define CONFIG_BTB                      /* enable branch predition */
  80
  81 #define CONFIG_SYS_MEMTEST_START        0x01000000      /* memtest works on */
  82 #define CONFIG_SYS_MEMTEST_END          0x01ffffff
  83
  84 /* DDR Setup */
  85 #define CONFIG_SYS_FSL_DDR3
  86 #undef CONFIG_SYS_DDR_RAW_TIMING
  87 #undef CONFIG_DDR_SPD
  88 #define CONFIG_SYS_SPD_BUS_NUM          0
  89 #define SPD_EEPROM_ADDRESS              0x52 /* I2C access */
  90
  91 #define CONFIG_MEM_INIT_VALUE           0xDeadBeef
  92
  93 #ifndef __ASSEMBLY__
  94 extern unsigned long get_sdram_size(void);
  95 #endif
  96 #define CONFIG_SYS_SDRAM_SIZE           get_sdram_size() /* DDR size */
  97 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  98 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  99
 100 #define CONFIG_NUM_DDR_CONTROLLERS      1
 101 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 102 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 103
 104 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 105 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 106 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 107
 108 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 109 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 110 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 111 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 112
 113 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 114 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 115 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 116 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 117 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3  */
 118 #define CONFIG_SYS_DDR_CONTROL_2        0x24401000
 119 #define CONFIG_SYS_DDR_TIMING_4         0x00000001
 120 #define CONFIG_SYS_DDR_TIMING_5         0x02401400
 121
 122 #define CONFIG_SYS_DDR_TIMING_3_800             0x00030000
 123 #define CONFIG_SYS_DDR_TIMING_0_800             0x00110104
 124 #define CONFIG_SYS_DDR_TIMING_1_800             0x6f6b8644
 125 #define CONFIG_SYS_DDR_TIMING_2_800             0x0fa888cf
 126 #define CONFIG_SYS_DDR_CLK_CTRL_800             0x03000000
 127 #define CONFIG_SYS_DDR_MODE_1_800               0x00441420
 128 #define CONFIG_SYS_DDR_MODE_2_800               0x8000c000
 129 #define CONFIG_SYS_DDR_INTERVAL_800             0x0c300100
 130 #define CONFIG_SYS_DDR_WRLVL_CONTROL_800        0x8675f608
 131
 132 /*
 133  * Base addresses -- Note these are effective addresses where the
 134  * actual resources get mapped (not physical addresses)
 135  */
 136 /* relocated CCSRBAR */
 137 #define CONFIG_SYS_CCSRBAR      CONFIG_SYS_CCSRBAR_DEFAULT
 138 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR_DEFAULT
 139
 140 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses */
 141                                                         /* CONFIG_SYS_IMMR */
 142 /* DSP CCSRBAR */
 143 #define CONFIG_SYS_FSL_DSP_CCSRBAR      CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 144 #define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 145
 146 /*
 147  * Memory map
 148  *
 149  * 0x0000_0000  0x3FFF_FFFF     DDR                     1G cacheable
 150  * 0x8800_0000  0x8810_0000     IFC internal SRAM               1M
 151  * 0xB000_0000  0xB0FF_FFFF     DSP core M2 memory      16M
 152  * 0xC100_0000  0xC13F_FFFF     MAPLE-2F                4M
 153  * 0xC1F0_0000  0xC1F3_FFFF     PA L2 SRAM Region 0     256K
 154  * 0xC1F8_0000  0xC1F9_FFFF     PA L2 SRAM Region 1     128K
 155  * 0xFED0_0000  0xFED0_3FFF     SEC Secured RAM         16K
 156  * 0xFF60_0000  0xFF6F_FFFF     DSP CCSR                1M
 157  * 0xFF70_0000  0xFF7F_FFFF     PA CCSR                 1M
 158  * 0xFF80_0000  0xFFFF_FFFF     Boot Page & NAND flash buffer   8M
 159  *
 160  */
 161
 162 /*
 163  * IFC Definitions
 164  */
 165 #define CONFIG_SYS_NO_FLASH
 166
 167 /* NAND Flash on IFC */
 168 #define CONFIG_SYS_NAND_BASE            0xff800000
 169 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 170
 171 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 172                                 | CSPR_PORT_SIZE_8      /* Port Size = 8 bit*/ \
 173                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 174                                 | CSPR_V)
 175 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 176
 177 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 178                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 179                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 180                                 | CSOR_NAND_RAL_2       /* RAL = 2Byes */ \
 181                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 182                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */ \
 183                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 184
 185 /* NAND Flash Timing Params */
 186 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x03)  \
 187                                         | FTIM0_NAND_TWP(0x05)   \
 188                                         | FTIM0_NAND_TWCHT(0x02) \
 189                                         | FTIM0_NAND_TWH(0x04))
 190 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x1C) \
 191                                         | FTIM1_NAND_TWBE(0x1E) \
 192                                         | FTIM1_NAND_TRR(0x07)  \
 193                                         | FTIM1_NAND_TRP(0x05))
 194 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x08)  \
 195                                         | FTIM2_NAND_TREH(0x04) \
 196                                         | FTIM2_NAND_TWHRE(0x11))
 197 #define CONFIG_SYS_NAND_FTIM3           FTIM3_NAND_TWW(0x04)
 198
 199 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 200 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 201 #define CONFIG_CMD_NAND
 202 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 203
 204 #define CONFIG_SYS_NAND_DDR_LAW         11
 205
 206 /* Set up IFC registers for boot location NAND */
 207 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 208 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 209 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 210 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 211 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 212 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 213 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 214
 215 #define CONFIG_BOARD_EARLY_INIT_F       /* Call board_pre_init */
 216
 217 #define CONFIG_SYS_INIT_RAM_LOCK
 218 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* stack in RAM */
 219 #define CONFIG_SYS_INIT_RAM_END         0x00004000/* End of used area in RAM */
 220
 221 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END \
 222                                                 - GENERATED_GBL_DATA_SIZE)
 223 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 224
 225 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 226 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc*/
 227
 228 /* Serial Port */
 229 #define CONFIG_CONS_INDEX       1
 230 #undef  CONFIG_SERIAL_SOFTWARE_FIFO
 231 #define CONFIG_SYS_NS16550
 232 #define CONFIG_SYS_NS16550_SERIAL
 233 #define CONFIG_SYS_NS16550_REG_SIZE     1
 234 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 235 #ifdef CONFIG_SPL_BUILD
 236 #define CONFIG_NS16550_MIN_FUNCTIONS
 237 #endif
 238
 239 #define CONFIG_SYS_CONSOLE_IS_IN_ENV    /* determine from environment */
 240
 241 #define CONFIG_SYS_BAUDRATE_TABLE       \
 242         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 243
 244 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 245
 246 /* Use the HUSH parser */
 247 #define CONFIG_SYS_HUSH_PARSER
 248 #ifdef  CONFIG_SYS_HUSH_PARSER
 249 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 250 #endif
 251
 252 /*
 253  * Pass open firmware flat tree
 254  */
 255 #define CONFIG_OF_LIBFDT
 256 #define CONFIG_OF_BOARD_SETUP
 257 #define CONFIG_OF_STDOUT_VIA_ALIAS
 258
 259 /* new uImage format support */
 260 #define CONFIG_FIT
 261 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
 262
 263 #define CONFIG_SYS_I2C
 264 #define CONFIG_SYS_I2C_FSL
 265 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 266 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 267 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 268
 269 /* I2C EEPROM */
 270 #define CONFIG_CMD_EEPROM
 271 #define CONFIG_SYS_I2C_MULTI_EEPROMS
 272 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 273 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 274 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 275
 276 #define CONFIG_CMD_I2C
 277
 278
 279 #define CONFIG_FSL_ESPI
 280 /* eSPI - Enhanced SPI */
 281 #ifdef CONFIG_FSL_ESPI
 282 #define CONFIG_SPI_FLASH
 283 #define CONFIG_SPI_FLASH_SPANSION
 284 #define CONFIG_CMD_SF
 285 #define CONFIG_SF_DEFAULT_SPEED         10000000
 286 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 287 #endif
 288
 289 #if defined(CONFIG_TSEC_ENET)
 290
 291 #define CONFIG_MII                      /* MII PHY management */
 292 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 293 #define CONFIG_TSEC1    1
 294 #define CONFIG_TSEC1_NAME       "eTSEC1"
 295 #define CONFIG_TSEC2    1
 296 #define CONFIG_TSEC2_NAME       "eTSEC2"
 297
 298 #define TSEC1_PHY_ADDR          0
 299 #define TSEC2_PHY_ADDR          3
 300
 301 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 302 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 303
 304 #define TSEC1_PHYIDX            0
 305
 306 #define TSEC2_PHYIDX            0
 307
 308 #define CONFIG_ETHPRIME         "eTSEC1"
 309
 310 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 311
 312 #endif  /* CONFIG_TSEC_ENET */
 313
 314 /*
 315  * Environment
 316  */
 317 #if defined(CONFIG_RAMBOOT_SPIFLASH)
 318 #define CONFIG_ENV_IS_IN_SPI_FLASH
 319 #define CONFIG_ENV_SPI_BUS      0
 320 #define CONFIG_ENV_SPI_CS       0
 321 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 322 #define CONFIG_ENV_SPI_MODE     0
 323 #define CONFIG_ENV_OFFSET       0x100000        /* 1MB */
 324 #define CONFIG_ENV_SECT_SIZE    0x10000
 325 #define CONFIG_ENV_SIZE         0x2000
 326 #elif defined(CONFIG_NAND)
 327 #define CONFIG_ENV_IS_IN_NAND
 328 #define CONFIG_SYS_EXTRA_ENV_RELOC
 329 #define CONFIG_ENV_SIZE         CONFIG_SYS_NAND_BLOCK_SIZE
 330 #define CONFIG_ENV_OFFSET       ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
 331 #define CONFIG_ENV_RANGE        (3 * CONFIG_ENV_SIZE)
 332 #elif defined(CONFIG_SYS_RAMBOOT)
 333 #define CONFIG_ENV_IS_NOWHERE   /* Store ENV in memory only */
 334 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 335 #define CONFIG_ENV_SIZE         0x2000
 336 #endif
 337
 338 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 339 #define CONFIG_SYS_LOADS_BAUD_CHANGE            /* allow baudrate change */
 340
 341 /*
 342  * Command line configuration.
 343  */
 344 #include <config_cmd_default.h>
 345
 346 #define CONFIG_CMD_DHCP
 347 #define CONFIG_CMD_ERRATA
 348 #define CONFIG_CMD_ELF
 349 #define CONFIG_CMD_EXT2
 350 #define CONFIG_CMD_FAT
 351 #define CONFIG_CMD_IRQ
 352 #define CONFIG_CMD_MII
 353 #define CONFIG_DOS_PARTITION
 354 #define CONFIG_CMD_PING
 355 #define CONFIG_CMD_REGINFO
 356 #define CONFIG_CMD_SETEXPR
 357
 358 /*
 359  * Miscellaneous configurable options
 360  */
 361 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 362 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 363 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 364 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 365
 366 #if defined(CONFIG_CMD_KGDB)
 367 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 368 #else
 369 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 370 #endif
 371 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 372                                                 /* Print Buffer Size */
 373 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 374 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 375
 376 /*
 377  * For booting Linux, the board info and command line data
 378  * have to be in the first 64 MB of memory, since this is
 379  * the maximum mapped by the Linux kernel during initialization.
 380  */
 381 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux */
 382 #define CONFIG_SYS_BOOTM_LEN    (64 << 20) /* Increase max gunzip size */
 383
 384 #if defined(CONFIG_CMD_KGDB)
 385 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 386 #endif
 387
 388 /* Hash command with SHA acceleration supported in hardware */
 389 #ifdef CONFIG_FSL_CAAM
 390 #define CONFIG_CMD_HASH
 391 #define CONFIG_SHA_HW_ACCEL
 392 #endif
 393
 394 #define CONFIG_USB_EHCI
 395
 396 #ifdef CONFIG_USB_EHCI
 397 #define CONFIG_CMD_USB
 398 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 399 #define CONFIG_USB_EHCI_FSL
 400 #define CONFIG_USB_STORAGE
 401 #define CONFIG_HAS_FSL_DR_USB
 402 #endif
 403
 404 /*
 405  * Dynamic MTD Partition support with mtdparts
 406  */
 407 #define CONFIG_MTD_DEVICE
 408 #define CONFIG_MTD_PARTITIONS
 409 #define CONFIG_CMD_MTDPARTS
 410 #define MTDIDS_DEFAULT "nand0=ff800000.flash,"
 411 #define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \
 412                         "8m(kernel),512k(dtb),-(fs)"
 413 /*
 414  * Override partitions in device tree using info
 415  * in "mtdparts" environment variable
 416  */
 417 #ifdef CONFIG_CMD_MTDPARTS
 418 #define CONFIG_FDT_FIXUP_PARTITIONS
 419 #endif
 420
 421 /*
 422  * Environment Configuration
 423  */
 424
 425 #if defined(CONFIG_TSEC_ENET)
 426 #define CONFIG_HAS_ETH0
 427 #endif
 428
 429 #define CONFIG_HOSTNAME         BSC9131rdb
 430 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 431 #define CONFIG_BOOTFILE         "uImage"
 432 #define CONFIG_UBOOTPATH        "u-boot.bin" /* U-Boot image on TFTP server */
 433
 434 #define CONFIG_BAUDRATE         115200
 435 #define CONFIG_BOOTDELAY        10 /* -1 disable auto-boot */
 436
 437 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 438         "netdev=eth0\0"                                         \
 439         "uboot=" CONFIG_UBOOTPATH "\0"                          \
 440         "loadaddr=1000000\0"                    \
 441         "bootfile=uImage\0"     \
 442         "consoledev=ttyS0\0"                            \
 443         "ramdiskaddr=2000000\0"                 \
 444         "ramdiskfile=rootfs.ext2.gz.uboot\0"            \
 445         "fdtaddr=c00000\0"                              \
 446         "fdtfile=bsc9131rdb.dtb\0"              \
 447         "bdev=sda1\0"   \
 448         "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"    \
 449         "bootm_size=0x37000000\0"       \
 450         "othbootargs=ramdisk_size=600000 " \
 451         "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
 452         "usbext2boot=setenv bootargs root=/dev/ram rw " \
 453         "console=$consoledev,$baudrate $othbootargs; "  \
 454         "usb start;"                    \
 455         "ext2load usb 0:4 $loadaddr $bootfile;"         \
 456         "ext2load usb 0:4 $fdtaddr $fdtfile;"   \
 457         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"   \
 458         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"       \
 459
 460 #define CONFIG_RAMBOOTCOMMAND           \
 461         "setenv bootargs root=/dev/ram rw "     \
 462         "console=$consoledev,$baudrate $othbootargs; "  \
 463         "tftp $ramdiskaddr $ramdiskfile;"       \
 464         "tftp $loadaddr $bootfile;"             \
 465         "tftp $fdtaddr $fdtfile;"               \
 466         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 467
 468 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
 469
 470 #endif  /* __CONFIG_H */