include/configs/CPCI4052.h

   1 /*
   2  * (C) Copyright 2001-2004
   3  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /*
  16  * High Level Configuration Options
  17  * (easy to change)
  18  */
  19
  20 #define CONFIG_405GP            1       /* This is a PPC405 CPU         */
  21 #define CONFIG_CPCI405          1       /* ...on a CPCI405 board        */
  22 #define CONFIG_CPCI405_VER2     1       /* ...version 2                 */
  23 #undef  CONFIG_CPCI405_6U               /* enable this for 6U boards    */
  24
  25 #define CONFIG_SYS_TEXT_BASE    0xFFFC0000
  26
  27 #define CONFIG_MISC_INIT_R       1      /* call misc_init_r()           */
  28
  29 #define CONFIG_SYS_CLK_FREQ     33330000 /* external frequency to pll   */
  30
  31 #define CONFIG_BAUDRATE         9600
  32
  33 #undef  CONFIG_BOOTARGS
  34 #undef  CONFIG_BOOTCOMMAND
  35
  36 #define CONFIG_PREBOOT                  /* enable preboot variable      */
  37
  38 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
  39 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
  40
  41 #define CONFIG_PPC4xx_EMAC
  42 #define CONFIG_MII              1       /* MII PHY management           */
  43 #define CONFIG_PHY_ADDR         0       /* PHY address                  */
  44 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
  45 #define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
  46
  47 #undef  CONFIG_HAS_ETH1
  48
  49 #define CONFIG_RTC_M48T35A      1               /* ST Electronics M48 timekeeper */
  50
  51 /*
  52  * BOOTP options
  53  */
  54 #define CONFIG_BOOTP_SUBNETMASK
  55 #define CONFIG_BOOTP_GATEWAY
  56 #define CONFIG_BOOTP_HOSTNAME
  57 #define CONFIG_BOOTP_BOOTPATH
  58 #define CONFIG_BOOTP_DNS
  59 #define CONFIG_BOOTP_DNS2
  60 #define CONFIG_BOOTP_SEND_HOSTNAME
  61
  62 /*
  63  * Command line configuration.
  64  */
  65 #define CONFIG_CMD_PCI
  66 #define CONFIG_CMD_IRQ
  67 #define CONFIG_CMD_IDE
  68 #define CONFIG_CMD_DATE
  69 #define CONFIG_CMD_BSP
  70 #define CONFIG_CMD_EEPROM
  71
  72 #define CONFIG_MAC_PARTITION
  73 #define CONFIG_DOS_PARTITION
  74
  75 #define CONFIG_SUPPORT_VFAT
  76
  77 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  78
  79 #define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */
  80
  81 /*
  82  * Miscellaneous configurable options
  83  */
  84 #undef CONFIG_SYS_LONGHELP                      /* undef to save memory         */
  85
  86 #if defined(CONFIG_CMD_KGDB)
  87 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
  88 #else
  89 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
  90 #endif
  91 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
  92 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
  93 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
  94
  95 #define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */
  96
  97 #define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup*/
  98
  99 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 100 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 101
 102 #define CONFIG_CONS_INDEX       1       /* Use UART0                    */
 103 #define CONFIG_SYS_NS16550_SERIAL
 104 #define CONFIG_SYS_NS16550_REG_SIZE     1
 105 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
 106
 107 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
 108 #define CONFIG_SYS_BASE_BAUD        691200
 109
 110 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 111 #define CONFIG_SYS_EXTBDINFO    1               /* To use extended board_into (bd_t) */
 112
 113 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 114
 115 #define CONFIG_SYS_RX_ETH_BUFFER        16      /* use 16 rx buffer on 405 emac */
 116
 117 /*-----------------------------------------------------------------------
 118  * PCI stuff
 119  *-----------------------------------------------------------------------
 120  */
 121 #define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
 122 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 123 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 124
 125 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
 126 #define CONFIG_PCI_HOST PCI_HOST_AUTO   /* select pci host function     */
 127                                         /* resource configuration       */
 128
 129 #define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
 130
 131 #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
 132
 133 #define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
 134
 135 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
 136 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
 137 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
 138 #define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
 139 #define CONFIG_SYS_PCI_PTM1LA  (bd->bi_memstart) /* point to sdram               */
 140 #define CONFIG_SYS_PCI_PTM1MS  (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
 141 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 142 #define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
 143 #define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
 144 #define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
 145
 146 #define CONFIG_PCI_4xx_PTM_OVERWRITE    1 /* overwrite PTMx settings by env */
 147
 148 /*-----------------------------------------------------------------------
 149  * IDE/ATA stuff
 150  *-----------------------------------------------------------------------
 151  */
 152 #undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
 153 #undef  CONFIG_IDE_LED                  /* no led for ide supported     */
 154 #define CONFIG_IDE_RESET        1       /* reset for ide supported      */
 155
 156 #define CONFIG_SYS_IDE_MAXBUS           1               /* max. 1 IDE busses    */
 157 #define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 158
 159 #define CONFIG_SYS_ATA_BASE_ADDR        0xF0100000
 160 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 161
 162 #define CONFIG_SYS_ATA_DATA_OFFSET      0x0000  /* Offset for data I/O                  */
 163 #define CONFIG_SYS_ATA_REG_OFFSET       0x0000  /* Offset for normal register accesses  */
 164 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0000  /* Offset for alternate registers       */
 165
 166 /*-----------------------------------------------------------------------
 167  * Start addresses for the final memory configuration
 168  * (Set up by the startup code)
 169  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 170  */
 171 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 172 #define CONFIG_SYS_FLASH_BASE           0xFFFC0000
 173 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 174 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB for Monitor   */
 175 #define CONFIG_SYS_MALLOC_LEN           (128 * 1024)    /* Reserve 128 kB for malloc()  */
 176
 177 #define CONFIG_PRAM             0       /* use pram variable to overwrite */
 178
 179 /*
 180  * For booting Linux, the board info and command line data
 181  * have to be in the first 8 MB of memory, since this is
 182  * the maximum mapped by the Linux kernel during initialization.
 183  */
 184 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 185
 186 /*-----------------------------------------------------------------------
 187  * FLASH organization
 188  */
 189 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* max number of memory banks           */
 190 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip    */
 191
 192 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
 193 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Timeout for Flash Write (in ms)      */
 194
 195 #define CONFIG_SYS_FLASH_WORD_SIZE      unsigned short  /* flash word size (width)      */
 196 #define CONFIG_SYS_FLASH_ADDR0          0x5555  /* 1st address for flash config cycles  */
 197 #define CONFIG_SYS_FLASH_ADDR1          0x2AAA  /* 2nd address for flash config cycles  */
 198 /*
 199  * The following defines are added for buggy IOP480 byte interface.
 200  * All other boards should use the standard values (CPCI405 etc.)
 201  */
 202 #define CONFIG_SYS_FLASH_READ0          0x0000  /* 0 is standard                        */
 203 #define CONFIG_SYS_FLASH_READ1          0x0001  /* 1 is standard                        */
 204 #define CONFIG_SYS_FLASH_READ2          0x0002  /* 2 is standard                        */
 205
 206 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* print 'E' for empty sector on flinfo */
 207
 208 #if 0 /* Use NVRAM for environment variables */
 209 /*-----------------------------------------------------------------------
 210  * NVRAM organization
 211  */
 212 #define CONFIG_ENV_IS_IN_NVRAM  1       /* use NVRAM for environment vars       */
 213 #define CONFIG_ENV_SIZE         0x0ff8          /* Size of Environment vars     */
 214 #define CONFIG_ENV_ADDR         \
 215         (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-(CONFIG_ENV_SIZE+8))  /* Env  */
 216
 217 #else /* Use EEPROM for environment variables */
 218
 219 #define CONFIG_ENV_IS_IN_EEPROM 1       /* use EEPROM for environment vars */
 220 #define CONFIG_ENV_OFFSET               0x000   /* environment starts at the beginning of the EEPROM */
 221 #define CONFIG_ENV_SIZE         0x800   /* 2048 bytes may be used for env vars*/
 222                                    /* total size of a CAT24WC16 is 2048 bytes */
 223 #endif
 224
 225 #define CONFIG_SYS_NVRAM_BASE_ADDR      0xf0200000              /* NVRAM base address   */
 226 #define CONFIG_SYS_NVRAM_SIZE           (32*1024)               /* NVRAM size           */
 227 #define CONFIG_SYS_VXWORKS_MAC_PTR     (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
 228
 229 /*-----------------------------------------------------------------------
 230  * I2C EEPROM (CAT24WC16) for environment
 231  */
 232 #define CONFIG_SYS_I2C
 233 #define CONFIG_SYS_I2C_PPC4XX
 234 #define CONFIG_SYS_I2C_PPC4XX_CH0
 235 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0           400000
 236 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0           0x7F
 237
 238 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM CAT28WC08             */
 239 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1        /* Bytes of address             */
 240 /* mask of address bits that overflow into the "EEPROM chip address"    */
 241 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
 242 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4     /* The Catalyst CAT24WC08 has   */
 243                                         /* 16 byte page write mode using*/
 244                                         /* last 4 bits of the address   */
 245 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */
 246
 247 /*
 248  * Init Memory Controller:
 249  *
 250  * BR0/1 and OR0/1 (FLASH)
 251  */
 252
 253 #define FLASH_BASE0_PRELIM      0xFF800000      /* FLASH bank #0        */
 254 #define FLASH_BASE1_PRELIM      0xFFC00000      /* FLASH bank #1        */
 255
 256 /*-----------------------------------------------------------------------
 257  * External Bus Controller (EBC) Setup
 258  */
 259
 260 /* Memory Bank 0 (Flash Bank 0) initialization                                  */
 261 #define CONFIG_SYS_EBC_PB0AP            0x92015480
 262 #define CONFIG_SYS_EBC_PB0CR            0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 263
 264 /* Memory Bank 1 (Flash Bank 1) initialization                                  */
 265 #define CONFIG_SYS_EBC_PB1AP            0x92015480
 266 #define CONFIG_SYS_EBC_PB1CR            0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 267
 268 /* Memory Bank 2 (CAN0, 1) initialization                                       */
 269 #define CONFIG_SYS_EBC_PB2AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 270 #define CONFIG_SYS_EBC_PB2CR            0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
 271 #define CONFIG_SYS_LED_ADDR             0xF0000380
 272
 273 /* Memory Bank 3 (CompactFlash IDE) initialization                              */
 274 #define CONFIG_SYS_EBC_PB3AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 275 #define CONFIG_SYS_EBC_PB3CR            0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 276
 277 /* Memory Bank 4 (NVRAM/RTC) initialization                                     */
 278 /*#define CONFIG_SYS_EBC_PB4AP            0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1     */
 279 #define CONFIG_SYS_EBC_PB4AP            0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1     */
 280 #define CONFIG_SYS_EBC_PB4CR            0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
 281
 282 /* Memory Bank 5 (optional Quart) initialization                                */
 283 #define CONFIG_SYS_EBC_PB5AP            0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
 284 #define CONFIG_SYS_EBC_PB5CR            0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
 285
 286 /* Memory Bank 6 (FPGA internal) initialization                                 */
 287 #define CONFIG_SYS_EBC_PB6AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 288 #define CONFIG_SYS_EBC_PB6CR            0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 289 #define CONFIG_SYS_FPGA_BASE_ADDR       0xF0400000
 290
 291 /*-----------------------------------------------------------------------
 292  * FPGA stuff
 293  */
 294 /* FPGA internal regs */
 295 #define CONFIG_SYS_FPGA_MODE            0x00
 296 #define CONFIG_SYS_FPGA_STATUS          0x02
 297 #define CONFIG_SYS_FPGA_TS              0x04
 298 #define CONFIG_SYS_FPGA_TS_LOW          0x06
 299 #define CONFIG_SYS_FPGA_TS_CAP0 0x10
 300 #define CONFIG_SYS_FPGA_TS_CAP0_LOW     0x12
 301 #define CONFIG_SYS_FPGA_TS_CAP1 0x14
 302 #define CONFIG_SYS_FPGA_TS_CAP1_LOW     0x16
 303 #define CONFIG_SYS_FPGA_TS_CAP2 0x18
 304 #define CONFIG_SYS_FPGA_TS_CAP2_LOW     0x1a
 305 #define CONFIG_SYS_FPGA_TS_CAP3 0x1c
 306 #define CONFIG_SYS_FPGA_TS_CAP3_LOW     0x1e
 307
 308 /* FPGA Mode Reg */
 309 #define CONFIG_SYS_FPGA_MODE_CF_RESET       0x0001
 310 #define CONFIG_SYS_FPGA_MODE_DUART_RESET   0x0002
 311 #define CONFIG_SYS_FPGA_MODE_ENABLE_OUTPUT 0x0004     /* only set on CPCI-405 Ver 3 */
 312 #define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
 313 #define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR  0x1000
 314 #define CONFIG_SYS_FPGA_MODE_TS_CLEAR       0x2000
 315
 316 /* FPGA Status Reg */
 317 #define CONFIG_SYS_FPGA_STATUS_DIP0     0x0001
 318 #define CONFIG_SYS_FPGA_STATUS_DIP1     0x0002
 319 #define CONFIG_SYS_FPGA_STATUS_DIP2     0x0004
 320 #define CONFIG_SYS_FPGA_STATUS_FLASH    0x0008
 321 #define CONFIG_SYS_FPGA_STATUS_TS_IRQ   0x1000
 322
 323 #define CONFIG_SYS_FPGA_SPARTAN2        1           /* using Xilinx Spartan 2 now    */
 324 #define CONFIG_SYS_FPGA_MAX_SIZE        32*1024     /* 32kByte is enough for XC2S15  */
 325
 326 /* FPGA program pin configuration */
 327 #define CONFIG_SYS_FPGA_PRG             0x04000000  /* FPGA program pin (ppc output) */
 328 #define CONFIG_SYS_FPGA_CLK             0x02000000  /* FPGA clk pin (ppc output)     */
 329 #define CONFIG_SYS_FPGA_DATA            0x01000000  /* FPGA data pin (ppc output)    */
 330 #define CONFIG_SYS_FPGA_INIT            0x00010000  /* FPGA init pin (ppc input)     */
 331 #define CONFIG_SYS_FPGA_DONE            0x00008000  /* FPGA done pin (ppc input)     */
 332
 333 /*-----------------------------------------------------------------------
 334  * Definitions for initial stack pointer and data area (in data cache)
 335  */
 336 #define CONFIG_SYS_INIT_DCACHE_CS       7       /* use cs # 7 for data cache memory    */
 337
 338 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000  /* use data cache                  */
 339 #define CONFIG_SYS_INIT_RAM_SIZE        0x2000  /* Size of used area in RAM            */
 340 #define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 341 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 342
 343 #endif  /* __CONFIG_H */