include/configs/M5249EVB.h

   1 /*
   2  * Configuation settings for the esd TASREG board.
   3  *
   4  * (C) Copyright 2004
   5  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
   6  *
   7  * See file CREDITS for list of people who contributed to this
   8  * project.
   9  *
  10  * This program is free software; you can redistribute it and/or
  11  * modify it under the terms of the GNU General Public License as
  12  * published by the Free Software Foundation; either version 2 of
  13  * the License, or (at your option) any later version.
  14  *
  15  * This program is distributed in the hope that it will be useful,
  16  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  17  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  18  * GNU General Public License for more details.
  19  *
  20  * You should have received a copy of the GNU General Public License
  21  * along with this program; if not, write to the Free Software
  22  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  23  * MA 02111-1307 USA
  24  */
  25
  26 /*
  27  * board/config.h - configuration options, board specific
  28  */
  29
  30 #ifndef _M5249EVB_H
  31 #define _M5249EVB_H
  32
  33 /*
  34  * High Level Configuration Options
  35  * (easy to change)
  36  */
  37 #define CONFIG_MCF52x2                  /* define processor family */
  38 #define CONFIG_M5249                    /* define processor type */
  39
  40 #define CONFIG_MCFTMR
  41
  42 #define CONFIG_MCFUART
  43 #define CONFIG_SYS_UART_PORT            (0)
  44 #define CONFIG_BAUDRATE         115200
  45 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600 , 19200 , 38400 , 57600, 115200 }
  46
  47 #undef  CONFIG_WATCHDOG
  48
  49 #undef CONFIG_MONITOR_IS_IN_RAM         /* no pre-loader required!!! ;-) */
  50
  51 /*
  52  * BOOTP options
  53  */
  54 #undef CONFIG_BOOTP_BOOTFILESIZE
  55 #undef CONFIG_BOOTP_BOOTPATH
  56 #undef CONFIG_BOOTP_GATEWAY
  57 #undef CONFIG_BOOTP_HOSTNAME
  58
  59 /*
  60  * Command line configuration.
  61  */
  62 #include <config_cmd_default.h>
  63 #undef CONFIG_CMD_NET
  64
  65 #define CONFIG_SYS_PROMPT               "=> "
  66 #define CONFIG_SYS_LONGHELP                             /* undef to save memory         */
  67
  68 #if defined(CONFIG_CMD_KGDB)
  69 #define CONFIG_SYS_CBSIZE               1024            /* Console I/O Buffer Size      */
  70 #else
  71 #define CONFIG_SYS_CBSIZE               256             /* Console I/O Buffer Size      */
  72 #endif
  73 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
  74 #define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
  75 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
  76
  77 #define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */
  78 #define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup        */
  79 #define CONFIG_AUTO_COMPLETE    1       /* add autocompletion support   */
  80 #define CONFIG_LOOPW            1       /* enable loopw command */
  81 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
  82
  83 #define CONFIG_SYS_LOAD_ADDR            0x200000        /* default load address */
  84
  85 #define CONFIG_SYS_MEMTEST_START        0x400
  86 #define CONFIG_SYS_MEMTEST_END          0x380000
  87
  88 #define CONFIG_SYS_HZ                   1000
  89
  90 /*
  91  * Clock configuration: enable only one of the following options
  92  */
  93
  94 #undef  CONFIG_SYS_PLL_BYPASS                           /* bypass PLL for test purpose */
  95 #define CONFIG_SYS_FAST_CLK             1               /* MCF5249 can run at 140MHz   */
  96 #define CONFIG_SYS_CLK                  132025600       /* MCF5249 can run at 140MHz   */
  97
  98 /*
  99  * Low Level Configuration Settings
 100  * (address mappings, register initial values, etc.)
 101  * You should know what you are doing if you make changes here.
 102  */
 103
 104 #define CONFIG_SYS_MBAR         0x10000000      /* Register Base Addrs */
 105 #define CONFIG_SYS_MBAR2                0x80000000
 106
 107 /*-----------------------------------------------------------------------
 108  * Definitions for initial stack pointer and data area (in DPRAM)
 109  */
 110 #define CONFIG_SYS_INIT_RAM_ADDR        0x20000000
 111 #define CONFIG_SYS_INIT_RAM_END 0x1000  /* End of used area in internal SRAM    */
 112 #define CONFIG_SYS_GBL_DATA_SIZE        64      /* size in bytes reserved for initial data */
 113 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 114 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 115
 116 #define CONFIG_ENV_IS_IN_FLASH  1
 117 #define CONFIG_ENV_OFFSET               0x4000  /* Address of Environment Sector*/
 118 #define CONFIG_ENV_SIZE         0x2000  /* Total Size of Environment Sector     */
 119 #define CONFIG_ENV_SECT_SIZE    0x2000 /* see README - env sector total size    */
 120
 121 /*-----------------------------------------------------------------------
 122  * Start addresses for the final memory configuration
 123  * (Set up by the startup code)
 124  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 125  */
 126 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 127 #define CONFIG_SYS_SDRAM_SIZE           16              /* SDRAM size in MB */
 128 #define CONFIG_SYS_FLASH_BASE           (CONFIG_SYS_CS0_BASE)
 129
 130 #if 0 /* test-only */
 131 #define CONFIG_PRAM             512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
 132 #endif
 133
 134 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 135
 136 #define CONFIG_SYS_MONITOR_LEN          0x20000
 137 #define CONFIG_SYS_MALLOC_LEN           (1 * 1024*1024) /* Reserve 1 MB for malloc()    */
 138 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 139
 140 /*
 141  * For booting Linux, the board info and command line data
 142  * have to be in the first 8 MB of memory, since this is
 143  * the maximum mapped by the Linux kernel during initialization ??
 144  */
 145 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 146
 147 /*-----------------------------------------------------------------------
 148  * FLASH organization
 149  */
 150 #define CONFIG_SYS_FLASH_CFI
 151 #ifdef CONFIG_SYS_FLASH_CFI
 152
 153 #       define CONFIG_FLASH_CFI_DRIVER  1
 154 #       define CONFIG_SYS_FLASH_SIZE            0x1000000       /* Max size that the board might have */
 155 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 156 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 157 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 158 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 159 #       define CONFIG_SYS_FLASH_CHECKSUM
 160 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_FLASH_BASE }
 161 #endif
 162
 163 /*-----------------------------------------------------------------------
 164  * Cache Configuration
 165  */
 166 #define CONFIG_SYS_CACHELINE_SIZE       16
 167
 168 /*-----------------------------------------------------------------------
 169  * Memory bank definitions
 170  */
 171
 172 /* CS0 - AMD Flash, address 0xffc00000 */
 173 #define CONFIG_SYS_CS0_BASE             0xffe00000
 174 #define CONFIG_SYS_CS0_CTRL             0x00001980      /* WS=0110, AA=1, PS=10         */
 175 /** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
 176 #define CONFIG_SYS_CS0_MASK             0x003f0021      /* 4MB, AA=0, WP=0, C/I=1, V=1  */
 177
 178 /* CS1 - FPGA, address 0xe0000000 */
 179 #define CONFIG_SYS_CS1_BASE             0xe0000000
 180 #define CONFIG_SYS_CS1_CTRL             0x00000d80      /* WS=0011, AA=1, PS=10         */
 181 #define CONFIG_SYS_CS1_MASK             0x00010001      /* 128kB, AA=0, WP=0, C/I=0, V=1*/
 182
 183 /*-----------------------------------------------------------------------
 184  * Port configuration
 185  */
 186 #define CONFIG_SYS_GPIO_FUNC            0x00000008      /* Set gpio pins: none          */
 187 #define CONFIG_SYS_GPIO1_FUNC           0x00df00f0      /* 36-39(SWITCH),48-52(FPGAs),54*/
 188 #define CONFIG_SYS_GPIO_EN              0x00000008      /* Set gpio output enable       */
 189 #define CONFIG_SYS_GPIO1_EN             0x00c70000      /* Set gpio output enable       */
 190 #define CONFIG_SYS_GPIO_OUT             0x00000008      /* Set outputs to default state */
 191 #define CONFIG_SYS_GPIO1_OUT            0x00c70000      /* Set outputs to default state */
 192 #define CONFIG_SYS_GPIO1_LED            0x00400000      /* user led                     */
 193
 194 #endif  /* M5249 */