include/configs/M5282EVB.h

   1 /*
   2  * Configuation settings for the Motorola MC5282EVB board.
   3  *
   4  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * board/config.h - configuration options, board specific
  11  */
  12
  13 #ifndef _CONFIG_M5282EVB_H
  14 #define _CONFIG_M5282EVB_H
  15
  16 /*
  17  * High Level Configuration Options
  18  * (easy to change)
  19  */
  20 #define CONFIG_MCFTMR
  21
  22 #define CONFIG_MCFUART
  23 #define CONFIG_SYS_UART_PORT            (0)
  24 #define CONFIG_BAUDRATE         115200
  25
  26 #undef  CONFIG_MONITOR_IS_IN_RAM        /* define if monitor is started from a pre-loader */
  27
  28 /* Configuration for environment
  29  * Environment is embedded in u-boot in the second sector of the flash
  30  */
  31 #define CONFIG_ENV_ADDR         0xffe04000
  32 #define CONFIG_ENV_SIZE         0x2000
  33 #define CONFIG_ENV_IS_IN_FLASH  1
  34
  35 #define LDS_BOARD_TEXT \
  36         . = DEFINED(env_offset) ? env_offset : .; \
  37         common/env_embedded.o (.text*);
  38
  39 /*
  40  * BOOTP options
  41  */
  42 #define CONFIG_BOOTP_BOOTFILESIZE
  43 #define CONFIG_BOOTP_BOOTPATH
  44 #define CONFIG_BOOTP_GATEWAY
  45 #define CONFIG_BOOTP_HOSTNAME
  46
  47 /*
  48  * Command line configuration.
  49  */
  50
  51 #define CONFIG_MCFFEC
  52 #ifdef CONFIG_MCFFEC
  53 #       define CONFIG_MII               1
  54 #       define CONFIG_MII_INIT          1
  55 #       define CONFIG_SYS_DISCOVER_PHY
  56 #       define CONFIG_SYS_RX_ETH_BUFFER 8
  57 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  58
  59 #       define CONFIG_SYS_FEC0_PINMUX           0
  60 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  61 #       define MCFFEC_TOUT_LOOP         50000
  62 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  63 #       ifndef CONFIG_SYS_DISCOVER_PHY
  64 #               define FECDUPLEX        FULL
  65 #               define FECSPEED         _100BASET
  66 #       else
  67 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  68 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  69 #               endif
  70 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
  71 #endif
  72
  73 #define CONFIG_BOOTDELAY        5
  74 #ifdef CONFIG_MCFFEC
  75 #       define CONFIG_IPADDR    192.162.1.2
  76 #       define CONFIG_NETMASK   255.255.255.0
  77 #       define CONFIG_SERVERIP  192.162.1.1
  78 #       define CONFIG_GATEWAYIP 192.162.1.1
  79 #endif                          /* CONFIG_MCFFEC */
  80
  81 #define CONFIG_HOSTNAME         M5282EVB
  82 #define CONFIG_EXTRA_ENV_SETTINGS               \
  83         "netdev=eth0\0"                         \
  84         "loadaddr=10000\0"                      \
  85         "u-boot=u-boot.bin\0"                   \
  86         "load=tftp ${loadaddr) ${u-boot}\0"     \
  87         "upd=run load; run prog\0"              \
  88         "prog=prot off ffe00000 ffe3ffff;"      \
  89         "era ffe00000 ffe3ffff;"                \
  90         "cp.b ${loadaddr} ffe00000 ${filesize};"\
  91         "save\0"                                \
  92         ""
  93
  94 #define CONFIG_SYS_LONGHELP             /* undef to save memory         */
  95
  96 #if defined(CONFIG_CMD_KGDB)
  97 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
  98 #else
  99 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
 100 #endif
 101 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 102 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 103 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 104
 105 #define CONFIG_SYS_LOAD_ADDR            0x20000
 106
 107 #define CONFIG_SYS_MEMTEST_START        0x400
 108 #define CONFIG_SYS_MEMTEST_END          0x380000
 109
 110 #define CONFIG_SYS_CLK                  64000000
 111
 112 /* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
 113
 114 #define CONFIG_SYS_MFD                  0x02    /* PLL Multiplication Factor Devider */
 115 #define CONFIG_SYS_RFD                  0x00    /* PLL Reduce Frecuency Devider */
 116
 117 /*
 118  * Low Level Configuration Settings
 119  * (address mappings, register initial values, etc.)
 120  * You should know what you are doing if you make changes here.
 121  */
 122 #define CONFIG_SYS_MBAR         0x40000000
 123
 124 /*-----------------------------------------------------------------------
 125  * Definitions for initial stack pointer and data area (in DPRAM)
 126  */
 127 #define CONFIG_SYS_INIT_RAM_ADDR        0x20000000
 128 #define CONFIG_SYS_INIT_RAM_SIZE        0x10000 /* Size of used area in internal SRAM    */
 129 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 130 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 131
 132 /*-----------------------------------------------------------------------
 133  * Start addresses for the final memory configuration
 134  * (Set up by the startup code)
 135  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 136  */
 137 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 138 #define CONFIG_SYS_SDRAM_SIZE           16      /* SDRAM size in MB */
 139 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_CS0_BASE
 140 #define CONFIG_SYS_INT_FLASH_BASE       0xf0000000
 141 #define CONFIG_SYS_INT_FLASH_ENABLE     0x21
 142
 143 /* If M5282 port is fully implemented the monitor base will be behind
 144  * the vector table. */
 145 #if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
 146 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 147 #else
 148 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418)  /* 24 Byte for CFM-Config */
 149 #endif
 150
 151 #define CONFIG_SYS_MONITOR_LEN          0x20000
 152 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 153 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 154
 155 /*
 156  * For booting Linux, the board info and command line data
 157  * have to be in the first 8 MB of memory, since this is
 158  * the maximum mapped by the Linux kernel during initialization ??
 159  */
 160 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 161
 162 /*-----------------------------------------------------------------------
 163  * FLASH organization
 164  */
 165 #define CONFIG_SYS_FLASH_CFI
 166 #ifdef CONFIG_SYS_FLASH_CFI
 167
 168 #       define CONFIG_FLASH_CFI_DRIVER  1
 169 #       define CONFIG_SYS_FLASH_SIZE            0x1000000       /* Max size that the board might have */
 170 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 171 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 172 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 173 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 174 #       define CONFIG_SYS_FLASH_CHECKSUM
 175 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_FLASH_BASE }
 176 #endif
 177
 178 /*-----------------------------------------------------------------------
 179  * Cache Configuration
 180  */
 181 #define CONFIG_SYS_CACHELINE_SIZE       16
 182
 183 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 184                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 185 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 186                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 187 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_CINV + CF_CACR_DCM)
 188 #define CONFIG_SYS_CACHE_ACR0           (CONFIG_SYS_SDRAM_BASE | \
 189                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 190                                          CF_ACR_EN | CF_ACR_SM_ALL)
 191 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_CENB | CF_CACR_DISD | \
 192                                          CF_CACR_CEIB | CF_CACR_DBWE | \
 193                                          CF_CACR_EUSP)
 194
 195 /*-----------------------------------------------------------------------
 196  * Memory bank definitions
 197  */
 198 #define CONFIG_SYS_CS0_BASE             0xFFE00000
 199 #define CONFIG_SYS_CS0_CTRL             0x00001980
 200 #define CONFIG_SYS_CS0_MASK             0x001F0001
 201
 202 /*-----------------------------------------------------------------------
 203  * Port configuration
 204  */
 205 #define CONFIG_SYS_PACNT                0x0000000       /* Port A D[31:24] */
 206 #define CONFIG_SYS_PADDR                0x0000000
 207 #define CONFIG_SYS_PADAT                0x0000000
 208
 209 #define CONFIG_SYS_PBCNT                0x0000000       /* Port B D[23:16] */
 210 #define CONFIG_SYS_PBDDR                0x0000000
 211 #define CONFIG_SYS_PBDAT                0x0000000
 212
 213 #define CONFIG_SYS_PCCNT                0x0000000       /* Port C D[15:08] */
 214 #define CONFIG_SYS_PCDDR                0x0000000
 215 #define CONFIG_SYS_PCDAT                0x0000000
 216
 217 #define CONFIG_SYS_PDCNT                0x0000000       /* Port D D[07:00] */
 218 #define CONFIG_SYS_PCDDR                0x0000000
 219 #define CONFIG_SYS_PCDAT                0x0000000
 220
 221 #define CONFIG_SYS_PEHLPAR              0xC0
 222 #define CONFIG_SYS_PUAPAR               0x0F    /* UA0..UA3 = Uart 0 +1 */
 223 #define CONFIG_SYS_DDRUA                0x05
 224 #define CONFIG_SYS_PJPAR                0xFF
 225
 226 #endif                          /* _CONFIG_M5282EVB_H */