include/configs/M54418TWR.h

   1 /*
   2  * Configuation settings for the Freescale MCF54418 TWR board.
   3  *
   4  * Copyright 2010-2012 Freescale Semiconductor, Inc.
   5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 /*
  11  * board/config.h - configuration options, board specific
  12  */
  13
  14 #ifndef _M54418TWR_H
  15 #define _M54418TWR_H
  16
  17 /*
  18  * High Level Configuration Options
  19  * (easy to change)
  20  */
  21 #define CONFIG_M54418TWR        /* M54418TWR board */
  22
  23 #define CONFIG_MCFUART
  24 #define CONFIG_SYS_UART_PORT            (0)
  25 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600 , 19200 , 38400 , 57600, 115200 }
  26
  27 #undef CONFIG_WATCHDOG
  28
  29 #define CONFIG_TIMESTAMP        /* Print image info with timestamp */
  30
  31 /*
  32  * BOOTP options
  33  */
  34 #define CONFIG_BOOTP_BOOTFILESIZE
  35 #define CONFIG_BOOTP_BOOTPATH
  36 #define CONFIG_BOOTP_GATEWAY
  37 #define CONFIG_BOOTP_HOSTNAME
  38
  39 /*
  40  * NAND FLASH
  41  */
  42 #ifdef CONFIG_CMD_NAND
  43 #define CONFIG_JFFS2_NAND
  44 #define CONFIG_NAND_FSL_NFC
  45 #define CONFIG_SYS_NAND_BASE            0xFC0FC000
  46 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  47 #define NAND_MAX_CHIPS                  CONFIG_SYS_MAX_NAND_DEVICE
  48 #define CONFIG_SYS_NAND_SELECT_DEVICE
  49 #endif
  50
  51 /* Network configuration */
  52 #define CONFIG_MCFFEC
  53 #ifdef CONFIG_MCFFEC
  54 #define CONFIG_MII                      1
  55 #define CONFIG_MII_INIT         1
  56 #define CONFIG_SYS_DISCOVER_PHY
  57 #define CONFIG_SYS_RX_ETH_BUFFER        2
  58 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  59 #define CONFIG_SYS_TX_ETH_BUFFER        2
  60 #define CONFIG_HAS_ETH1
  61
  62 #define CONFIG_SYS_FEC0_PINMUX          0
  63 #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
  64 #define CONFIG_SYS_FEC1_PINMUX          0
  65 #define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE
  66 #define MCFFEC_TOUT_LOOP                50000
  67 #define CONFIG_SYS_FEC0_PHYADDR 0
  68 #define CONFIG_SYS_FEC1_PHYADDR 1
  69
  70 #define CONFIG_ETHPRIME "FEC0"
  71 #define CONFIG_IPADDR           192.168.1.2
  72 #define CONFIG_NETMASK          255.255.255.0
  73 #define CONFIG_SERVERIP 192.168.1.1
  74 #define CONFIG_GATEWAYIP        192.168.1.1
  75
  76 #define CONFIG_SYS_FEC_BUF_USE_SRAM
  77 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  78 #ifndef CONFIG_SYS_DISCOVER_PHY
  79 #define FECDUPLEX       FULL
  80 #define FECSPEED        _100BASET
  81 #define LINKSTATUS      1
  82 #else
  83 #define LINKSTATUS      0
  84 #ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  85 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  86 #endif
  87 #endif                  /* CONFIG_SYS_DISCOVER_PHY */
  88 #endif
  89
  90 #define CONFIG_HOSTNAME         M54418TWR
  91
  92 #if defined(CONFIG_CF_SBF)
  93 /* ST Micro serial flash */
  94 #define CONFIG_SYS_LOAD_ADDR2           0x40010007
  95 #define CONFIG_EXTRA_ENV_SETTINGS               \
  96         "netdev=eth0\0"                         \
  97         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
  98         "loadaddr=0x40010000\0"                 \
  99         "sbfhdr=sbfhdr.bin\0"                   \
 100         "uboot=u-boot.bin\0"                    \
 101         "load=tftp ${loadaddr} ${sbfhdr};"      \
 102         "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0"       \
 103         "upd=run load; run prog\0"              \
 104         "prog=sf probe 0:1 1000000 3;"          \
 105         "sf erase 0 40000;"                     \
 106         "sf write ${loadaddr} 0 40000;"         \
 107         "save\0"                                \
 108         ""
 109 #elif defined(CONFIG_SYS_NAND_BOOT)
 110 #define CONFIG_EXTRA_ENV_SETTINGS               \
 111         "netdev=eth0\0"                         \
 112         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
 113         "loadaddr=0x40010000\0"                 \
 114         "u-boot=u-boot.bin\0"                   \
 115         "load=tftp ${loadaddr} ${u-boot};\0"    \
 116         "upd=run load; run prog\0"              \
 117         "prog=nand device 0;"                   \
 118         "nand erase 0 40000;"                   \
 119         "nb_update ${loadaddr} ${filesize};"    \
 120         "save\0"                                \
 121         ""
 122 #else
 123 #define CONFIG_SYS_UBOOT_END    0x3FFFF
 124 #define CONFIG_EXTRA_ENV_SETTINGS               \
 125         "netdev=eth0\0"                         \
 126         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
 127         "loadaddr=40010000\0"                   \
 128         "u-boot=u-boot.bin\0"                   \
 129         "load=tftp ${loadaddr) ${u-boot}\0"     \
 130         "upd=run load; run prog\0"              \
 131         "prog=prot off mram" " ;"       \
 132         "cp.b ${loadaddr} 0 ${filesize};"       \
 133         "save\0"                                \
 134         ""
 135 #endif
 136
 137 /* Realtime clock */
 138 #undef CONFIG_MCFRTC
 139 #define CONFIG_RTC_MCFRRTC
 140 #define CONFIG_SYS_MCFRRTC_BASE         0xFC0A8000
 141
 142 /* Timer */
 143 #define CONFIG_MCFTMR
 144 #undef CONFIG_MCFPIT
 145
 146 /* I2c */
 147 #undef CONFIG_SYS_FSL_I2C
 148 #undef  CONFIG_SYS_I2C_SOFT     /* I2C bit-banged */
 149 /* I2C speed and slave address  */
 150 #define CONFIG_SYS_I2C_SPEED            80000
 151 #define CONFIG_SYS_I2C_SLAVE            0x7F
 152 #define CONFIG_SYS_I2C_OFFSET           0x58000
 153 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
 154
 155 /* DSPI and Serial Flash */
 156 #define CONFIG_CF_SPI
 157 #define CONFIG_CF_DSPI
 158 #define CONFIG_SERIAL_FLASH
 159 #define CONFIG_HARD_SPI
 160 #define CONFIG_SYS_SBFHDR_SIZE          0x7
 161 #ifdef CONFIG_CMD_SPI
 162
 163 #       define CONFIG_SYS_DSPI_CTAR0    (DSPI_CTAR_TRSZ(7) | \
 164                                          DSPI_CTAR_PCSSCK_1CLK | \
 165                                          DSPI_CTAR_PASC(0) | \
 166                                          DSPI_CTAR_PDT(0) | \
 167                                          DSPI_CTAR_CSSCK(0) | \
 168                                          DSPI_CTAR_ASC(0) | \
 169                                          DSPI_CTAR_DT(1))
 170 #       define CONFIG_SYS_DSPI_CTAR1    (CONFIG_SYS_DSPI_CTAR0)
 171 #       define CONFIG_SYS_DSPI_CTAR2    (CONFIG_SYS_DSPI_CTAR0)
 172 #endif
 173
 174 /* Input, PCI, Flexbus, and VCO */
 175 #define CONFIG_EXTRA_CLOCK
 176
 177 #define CONFIG_PRAM                     2048    /* 2048 KB */
 178
 179 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 180
 181 #if defined(CONFIG_CMD_KGDB)
 182 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 183 #else
 184 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size */
 185 #endif
 186 /* Print Buffer Size */
 187 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 188                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 189 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 190 /* Boot Argument Buffer Size    */
 191 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 192
 193 #define CONFIG_SYS_LOAD_ADDR            (CONFIG_SYS_SDRAM_BASE + 0x10000)
 194
 195 #define CONFIG_SYS_MBAR         0xFC000000
 196
 197 /*
 198  * Low Level Configuration Settings
 199  * (address mappings, register initial values, etc.)
 200  * You should know what you are doing if you make changes here.
 201  */
 202
 203 /*-----------------------------------------------------------------------
 204  * Definitions for initial stack pointer and data area (in DPRAM)
 205  */
 206 #define CONFIG_SYS_INIT_RAM_ADDR        0x80000000
 207 /* End of used area in internal SRAM */
 208 #define CONFIG_SYS_INIT_RAM_SIZE        0x10000
 209 #define CONFIG_SYS_INIT_RAM_CTRL        0x221
 210 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - \
 211                                         GENERATED_GBL_DATA_SIZE) - 32)
 212 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 213 #define CONFIG_SYS_SBFHDR_DATA_OFFSET   (CONFIG_SYS_INIT_RAM_SIZE - 32)
 214
 215 /*-----------------------------------------------------------------------
 216  * Start addresses for the final memory configuration
 217  * (Set up by the startup code)
 218  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 219  */
 220 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 221 #define CONFIG_SYS_SDRAM_SIZE           128     /* SDRAM size in MB */
 222
 223 #define CONFIG_SYS_MEMTEST_START        (CONFIG_SYS_SDRAM_BASE + 0x400)
 224 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 225 #define CONFIG_SYS_DRAM_TEST
 226
 227 #if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT)
 228 #define CONFIG_SERIAL_BOOT
 229 #endif
 230
 231 #if defined(CONFIG_SERIAL_BOOT)
 232 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
 233 #else
 234 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 235 #endif
 236
 237 #define CONFIG_SYS_BOOTPARAMS_LEN       (64 * 1024)
 238 /* Reserve 256 kB for Monitor */
 239 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 240 /* Reserve 256 kB for malloc() */
 241 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 242
 243 /*
 244  * For booting Linux, the board info and command line data
 245  * have to be in the first 8 MB of memory, since this is
 246  * the maximum mapped by the Linux kernel during initialization ??
 247  */
 248 /* Initial Memory map for Linux */
 249 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
 250                                 (CONFIG_SYS_SDRAM_SIZE << 20))
 251
 252 /* Configuration for environment
 253  * Environment is embedded in u-boot in the second sector of the flash
 254  */
 255 #if !defined(CONFIG_SERIAL_BOOT)  /*MRAM boot*/
 256 #define CONFIG_ENV_ADDR         (0x40000 - 0x1000) /*MRAM size 40000*/
 257 #define CONFIG_ENV_SIZE         0x1000
 258 #endif
 259
 260 #if defined(CONFIG_CF_SBF)
 261 #define CONFIG_ENV_SPI_CS               1
 262 #define CONFIG_ENV_OFFSET               0x40000
 263 #define CONFIG_ENV_SIZE         0x2000
 264 #define CONFIG_ENV_SECT_SIZE            0x10000
 265 #endif
 266 #if defined(CONFIG_SYS_NAND_BOOT)
 267 #define CONFIG_ENV_OFFSET       0x80000
 268 #define CONFIG_ENV_SIZE 0x20000
 269 #define CONFIG_ENV_SECT_SIZE    0x20000
 270 #endif
 271 #undef CONFIG_ENV_OVERWRITE
 272
 273 /* FLASH organization */
 274 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_CS0_BASE
 275
 276 #undef CONFIG_SYS_FLASH_CFI
 277 #ifdef CONFIG_SYS_FLASH_CFI
 278
 279 #define CONFIG_FLASH_CFI_DRIVER 1
 280 /* Max size that the board might have */
 281 #define CONFIG_SYS_FLASH_SIZE           0x1000000
 282 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 283 /* max number of memory banks */
 284 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 285 /* max number of sectors on one chip */
 286 #define CONFIG_SYS_MAX_FLASH_SECT       270
 287 /* "Real" (hardware) sectors protection */
 288 #define CONFIG_SYS_FLASH_PROTECTION
 289 #define CONFIG_SYS_FLASH_CHECKSUM
 290 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_CS0_BASE }
 291 #else
 292 /* max number of sectors on one chip */
 293 #define CONFIG_SYS_MAX_FLASH_SECT       270
 294 /* max number of sectors on one chip */
 295 #define CONFIG_SYS_MAX_FLASH_BANKS      0
 296 #endif
 297
 298 /*
 299  * This is setting for JFFS2 support in u-boot.
 300  * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
 301  */
 302 #ifdef CONFIG_CMD_JFFS2
 303 #define CONFIG_JFFS2_DEV                "nand0"
 304 #define CONFIG_JFFS2_PART_OFFSET        (0x800000)
 305 #define CONFIG_MTD_DEVICE
 306 #define MTDIDS_DEFAULT          "nand0=m54418twr.nand"
 307
 308 #define MTDPARTS_DEFAULT        "mtdparts=m54418twr.nand:1m(data),"     \
 309                                                 "7m(kernel),"           \
 310                                                 "-(rootfs)"
 311
 312 #endif
 313
 314 #ifdef CONFIG_CMD_UBI
 315 #define CONFIG_MTD_DEVICE       /* needed for mtdparts command */
 316 #define CONFIG_MTD_PARTITIONS   /* mtdparts and UBI support */
 317 #define MTDIDS_DEFAULT          "nand0=NAND"
 318 #define MTDPARTS_DEFAULT        "mtdparts=NAND:1m(u-boot),"     \
 319                                         "-(ubi)"
 320 #endif
 321 /* Cache Configuration */
 322 #define CONFIG_SYS_CACHELINE_SIZE       16
 323 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 324                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 325 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 326                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 327 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA)
 328 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 329 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 330                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 331                                          CF_ACR_EN | CF_ACR_SM_ALL)
 332 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_IEC | \
 333                                          CF_CACR_ICINVA | CF_CACR_EUSP)
 334 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 335                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 336                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 337
 338 #define CACR_STATUS     (CONFIG_SYS_INIT_RAM_ADDR + \
 339                         CONFIG_SYS_INIT_RAM_SIZE - 12)
 340
 341 /*-----------------------------------------------------------------------
 342  * Memory bank definitions
 343  */
 344 /*
 345  * CS0 - NOR Flash 16MB
 346  * CS1 - Available
 347  * CS2 - Available
 348  * CS3 - Available
 349  * CS4 - Available
 350  * CS5 - Available
 351  */
 352
 353  /* Flash */
 354 #define CONFIG_SYS_CS0_BASE             0x00000000
 355 #define CONFIG_SYS_CS0_MASK             0x000F0101
 356 #define CONFIG_SYS_CS0_CTRL             0x00001D60
 357
 358 #endif                          /* _M54418TWR_H */