include/configs/M5475EVB.h

   1 /*
   2  * Configuation settings for the Freescale MCF5475 board.
   3  *
   4  * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
   5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 /*
  11  * board/config.h - configuration options, board specific
  12  */
  13
  14 #ifndef _M5475EVB_H
  15 #define _M5475EVB_H
  16
  17 /*
  18  * High Level Configuration Options
  19  * (easy to change)
  20  */
  21
  22 #define CONFIG_MCFUART
  23 #define CONFIG_SYS_UART_PORT            (0)
  24
  25 #undef CONFIG_HW_WATCHDOG
  26 #define CONFIG_WATCHDOG_TIMEOUT 5000    /* timeout in milliseconds, max timeout is 6.71sec */
  27
  28 /* Command line configuration */
  29 #define CONFIG_CMD_PCI
  30
  31 #define CONFIG_SLTTMR
  32
  33 #define CONFIG_FSLDMAFEC
  34 #ifdef CONFIG_FSLDMAFEC
  35 #       define CONFIG_MII               1
  36 #       define CONFIG_MII_INIT          1
  37 #       define CONFIG_HAS_ETH1
  38
  39 #       define CONFIG_SYS_DMA_USE_INTSRAM       1
  40 #       define CONFIG_SYS_DISCOVER_PHY
  41 #       define CONFIG_SYS_RX_ETH_BUFFER 32
  42 #       define CONFIG_SYS_TX_ETH_BUFFER 48
  43 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  44
  45 #       define CONFIG_SYS_FEC0_PINMUX           0
  46 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  47 #       define CONFIG_SYS_FEC1_PINMUX           0
  48 #       define CONFIG_SYS_FEC1_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  49
  50 #       define MCFFEC_TOUT_LOOP         50000
  51 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  52 #       ifndef CONFIG_SYS_DISCOVER_PHY
  53 #               define FECDUPLEX        FULL
  54 #               define FECSPEED         _100BASET
  55 #       else
  56 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  57 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  58 #               endif
  59 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
  60
  61 #       define CONFIG_IPADDR    192.162.1.2
  62 #       define CONFIG_NETMASK   255.255.255.0
  63 #       define CONFIG_SERVERIP  192.162.1.1
  64 #       define CONFIG_GATEWAYIP 192.162.1.1
  65
  66 #endif
  67
  68 #ifdef CONFIG_CMD_USB
  69 #       define CONFIG_USB_OHCI_NEW
  70
  71 #       ifndef CONFIG_CMD_PCI
  72 #               define CONFIG_CMD_PCI
  73 #       endif
  74 #       define CONFIG_PCI_OHCI
  75
  76 #       undef CONFIG_SYS_USB_OHCI_BOARD_INIT
  77 #       undef CONFIG_SYS_USB_OHCI_CPU_INIT
  78 #       define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS       15
  79 #       define CONFIG_SYS_USB_OHCI_SLOT_NAME            "isp1561"
  80 #       define CONFIG_SYS_OHCI_SWAP_REG_ACCESS
  81 #endif
  82
  83 /* I2C */
  84 #define CONFIG_SYS_I2C
  85 #define CONFIG_SYS_I2C_FSL
  86 #define CONFIG_SYS_FSL_I2C_SPEED        80000
  87 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
  88 #define CONFIG_SYS_FSL_I2C_OFFSET       0x00008F00
  89 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
  90
  91 /* PCI */
  92 #ifdef CONFIG_CMD_PCI
  93 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
  94
  95 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE  8
  96
  97 #define CONFIG_SYS_PCI_MEM_BUS          0x80000000
  98 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS
  99 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
 100
 101 #define CONFIG_SYS_PCI_IO_BUS           0x71000000
 102 #define CONFIG_SYS_PCI_IO_PHYS          CONFIG_SYS_PCI_IO_BUS
 103 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000
 104
 105 #define CONFIG_SYS_PCI_CFG_BUS          0x70000000
 106 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS
 107 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000
 108 #endif
 109
 110 #define CONFIG_UDP_CHECKSUM
 111
 112 #ifdef CONFIG_MCFFEC
 113 #       define CONFIG_IPADDR    192.162.1.2
 114 #       define CONFIG_NETMASK   255.255.255.0
 115 #       define CONFIG_SERVERIP  192.162.1.1
 116 #       define CONFIG_GATEWAYIP 192.162.1.1
 117 #endif                          /* FEC_ENET */
 118
 119 #define CONFIG_HOSTNAME         M547xEVB
 120 #define CONFIG_EXTRA_ENV_SETTINGS               \
 121         "netdev=eth0\0"                         \
 122         "loadaddr=10000\0"                      \
 123         "u-boot=u-boot.bin\0"                   \
 124         "load=tftp ${loadaddr) ${u-boot}\0"     \
 125         "upd=run load; run prog\0"              \
 126         "prog=prot off bank 1;"                 \
 127         "era ff800000 ff83ffff;"                \
 128         "cp.b ${loadaddr} ff800000 ${filesize};"\
 129         "save\0"                                \
 130         ""
 131
 132 #define CONFIG_PRAM             512     /* 512 KB */
 133 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 134
 135 #ifdef CONFIG_CMD_KGDB
 136 #       define CONFIG_SYS_CBSIZE        1024    /* Console I/O Buffer Size */
 137 #else
 138 #       define CONFIG_SYS_CBSIZE        256     /* Console I/O Buffer Size */
 139 #endif
 140
 141 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)        /* Print Buffer Size */
 142 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 143 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 144 #define CONFIG_SYS_LOAD_ADDR            0x00010000
 145
 146 #define CONFIG_SYS_CLK                  CONFIG_SYS_BUSCLK
 147 #define CONFIG_SYS_CPU_CLK              CONFIG_SYS_CLK * 2
 148
 149 #define CONFIG_SYS_MBAR         0xF0000000
 150 #define CONFIG_SYS_INTSRAM              (CONFIG_SYS_MBAR + 0x10000)
 151 #define CONFIG_SYS_INTSRAMSZ            0x8000
 152
 153 /*#define CONFIG_SYS_LATCH_ADDR         (CONFIG_SYS_CS1_BASE + 0x80000)*/
 154
 155 /*
 156  * Low Level Configuration Settings
 157  * (address mappings, register initial values, etc.)
 158  * You should know what you are doing if you make changes here.
 159  */
 160 /*-----------------------------------------------------------------------
 161  * Definitions for initial stack pointer and data area (in DPRAM)
 162  */
 163 #define CONFIG_SYS_INIT_RAM_ADDR        0xF2000000
 164 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in internal SRAM */
 165 #define CONFIG_SYS_INIT_RAM_CTRL        0x21
 166 #define CONFIG_SYS_INIT_RAM1_ADDR       (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
 167 #define CONFIG_SYS_INIT_RAM1_END        0x1000  /* End of used area in internal SRAM */
 168 #define CONFIG_SYS_INIT_RAM1_CTRL       0x21
 169 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
 170 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 171
 172 /*-----------------------------------------------------------------------
 173  * Start addresses for the final memory configuration
 174  * (Set up by the startup code)
 175  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 176  */
 177 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 178 #define CONFIG_SYS_SDRAM_CFG1           0x73711630
 179 #define CONFIG_SYS_SDRAM_CFG2           0x46770000
 180 #define CONFIG_SYS_SDRAM_CTRL           0xE10B0000
 181 #define CONFIG_SYS_SDRAM_EMOD           0x40010000
 182 #define CONFIG_SYS_SDRAM_MODE           0x018D0000
 183 #define CONFIG_SYS_SDRAM_DRVSTRENGTH    0x000002AA
 184 #ifdef CONFIG_SYS_DRAMSZ1
 185 #       define CONFIG_SYS_SDRAM_SIZE    (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1)
 186 #else
 187 #       define CONFIG_SYS_SDRAM_SIZE    CONFIG_SYS_DRAMSZ
 188 #endif
 189
 190 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE + 0x400
 191 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 192
 193 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 194 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor */
 195
 196 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 197
 198 /* Reserve 256 kB for malloc() */
 199 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 200 /*
 201  * For booting Linux, the board info and command line data
 202  * have to be in the first 8 MB of memory, since this is
 203  * the maximum mapped by the Linux kernel during initialization ??
 204  */
 205 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 206
 207 /*-----------------------------------------------------------------------
 208  * FLASH organization
 209  */
 210 #define CONFIG_SYS_FLASH_CFI
 211 #ifdef CONFIG_SYS_FLASH_CFI
 212 #       define CONFIG_SYS_FLASH_BASE            (CONFIG_SYS_CS0_BASE)
 213 #       define CONFIG_FLASH_CFI_DRIVER  1
 214 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 215 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 216 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 217 #       define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 218 #ifdef CONFIG_SYS_NOR1SZ
 219 #       define CONFIG_SYS_MAX_FLASH_BANKS       2       /* max number of memory banks */
 220 #       define CONFIG_SYS_FLASH_SIZE            ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20)
 221 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
 222 #else
 223 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 224 #       define CONFIG_SYS_FLASH_SIZE            (CONFIG_SYS_BOOTSZ << 20)
 225 #endif
 226 #endif
 227
 228 /* Configuration for environment
 229  * Environment is not embedded in u-boot but at offset 0x40000 on the flash.
 230  * First time runing may have env crc error warning if there is
 231  * no correct environment on the flash.
 232  */
 233 #define CONFIG_ENV_OFFSET               0x40000
 234 #define CONFIG_ENV_SECT_SIZE    0x10000
 235
 236 /*-----------------------------------------------------------------------
 237  * Cache Configuration
 238  */
 239 #define CONFIG_SYS_CACHELINE_SIZE       16
 240
 241 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 242                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 243 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 244                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 245 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA + \
 246                                          CF_CACR_IDCM)
 247 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 248 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 249                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 250                                          CF_ACR_EN | CF_ACR_SM_ALL)
 251 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_BCINVA | \
 252                                          CF_CACR_IEC | CF_CACR_ICINVA)
 253 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 254                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 255                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 256
 257 /*-----------------------------------------------------------------------
 258  * Chipselect bank definitions
 259  */
 260 /*
 261  * CS0 - NOR Flash 1, 2, 4, or 8MB
 262  * CS1 - NOR Flash
 263  * CS2 - Available
 264  * CS3 - Available
 265  * CS4 - Available
 266  * CS5 - Available
 267  */
 268 #define CONFIG_SYS_CS0_BASE             0xFF800000
 269 #define CONFIG_SYS_CS0_MASK             (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001)
 270 #define CONFIG_SYS_CS0_CTRL             0x00101980
 271
 272 #ifdef CONFIG_SYS_NOR1SZ
 273 #define CONFIG_SYS_CS1_BASE             0xE0000000
 274 #define CONFIG_SYS_CS1_MASK             (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001)
 275 #define CONFIG_SYS_CS1_CTRL             0x00101D80
 276 #endif
 277
 278 #endif                          /* _M5475EVB_H */