include/configs/M5485EVB.h

   1 /*
   2  * Configuation settings for the Freescale MCF5485 FireEngine board.
   3  *
   4  * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
   5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 /*
  11  * board/config.h - configuration options, board specific
  12  */
  13
  14 #ifndef _M5485EVB_H
  15 #define _M5485EVB_H
  16
  17 /*
  18  * High Level Configuration Options
  19  * (easy to change)
  20  */
  21
  22 #define CONFIG_MCFUART
  23 #define CONFIG_SYS_UART_PORT            (0)
  24 #define CONFIG_BAUDRATE         115200
  25
  26 #undef CONFIG_HW_WATCHDOG
  27 #define CONFIG_WATCHDOG_TIMEOUT 5000    /* timeout in milliseconds, max timeout is 6.71sec */
  28
  29 /* Command line configuration */
  30 #undef CONFIG_CMD_DATE
  31 #define CONFIG_CMD_PCI
  32 #define CONFIG_CMD_REGINFO
  33
  34 #define CONFIG_SLTTMR
  35
  36 #define CONFIG_FSLDMAFEC
  37 #ifdef CONFIG_FSLDMAFEC
  38 #       define CONFIG_MII               1
  39 #       define CONFIG_MII_INIT          1
  40 #       define CONFIG_HAS_ETH1
  41
  42 #       define CONFIG_SYS_DMA_USE_INTSRAM       1
  43 #       define CONFIG_SYS_DISCOVER_PHY
  44 #       define CONFIG_SYS_RX_ETH_BUFFER 32
  45 #       define CONFIG_SYS_TX_ETH_BUFFER 48
  46 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  47
  48 #       define CONFIG_SYS_FEC0_PINMUX           0
  49 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  50 #       define CONFIG_SYS_FEC1_PINMUX           0
  51 #       define CONFIG_SYS_FEC1_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  52
  53 #       define MCFFEC_TOUT_LOOP         50000
  54 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  55 #       ifndef CONFIG_SYS_DISCOVER_PHY
  56 #               define FECDUPLEX        FULL
  57 #               define FECSPEED         _100BASET
  58 #       else
  59 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  60 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  61 #               endif
  62 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
  63
  64 #       define CONFIG_IPADDR    192.162.1.2
  65 #       define CONFIG_NETMASK   255.255.255.0
  66 #       define CONFIG_SERVERIP  192.162.1.1
  67 #       define CONFIG_GATEWAYIP 192.162.1.1
  68
  69 #endif
  70
  71 #ifdef CONFIG_CMD_USB
  72 #       define CONFIG_DOS_PARTITION
  73 #       define CONFIG_USB_OHCI_NEW
  74 #       ifndef CONFIG_CMD_PCI
  75 #               define CONFIG_CMD_PCI
  76 #       endif
  77 /*#     define CONFIG_PCI_OHCI*/
  78 #       define CONFIG_SYS_USB_OHCI_REGS_BASE            0x80041000
  79 #       define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS       15
  80 #       define CONFIG_SYS_USB_OHCI_SLOT_NAME            "isp1561"
  81 #       define CONFIG_SYS_OHCI_SWAP_REG_ACCESS
  82 #endif
  83
  84 /* I2C */
  85 #define CONFIG_SYS_I2C
  86 #define CONFIG_SYS_I2C_FSL
  87 #define CONFIG_SYS_FSL_I2C_SPEED        80000
  88 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
  89 #define CONFIG_SYS_FSL_I2C_OFFSET       0x00008F00
  90 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
  91
  92 /* PCI */
  93 #ifdef CONFIG_CMD_PCI
  94 #define CONFIG_PCI_PNP          1
  95 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
  96
  97 #define CONFIG_SYS_PCI_MEM_BUS          0x80000000
  98 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS
  99 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
 100
 101 #define CONFIG_SYS_PCI_IO_BUS           0x71000000
 102 #define CONFIG_SYS_PCI_IO_PHYS          CONFIG_SYS_PCI_IO_BUS
 103 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000
 104
 105 #define CONFIG_SYS_PCI_CFG_BUS          0x70000000
 106 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS
 107 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000
 108 #endif
 109
 110 #define CONFIG_UDP_CHECKSUM
 111
 112 #define CONFIG_HOSTNAME         M548xEVB
 113 #define CONFIG_EXTRA_ENV_SETTINGS               \
 114         "netdev=eth0\0"                         \
 115         "loadaddr=10000\0"                      \
 116         "u-boot=u-boot.bin\0"                   \
 117         "load=tftp ${loadaddr) ${u-boot}\0"     \
 118         "upd=run load; run prog\0"              \
 119         "prog=prot off bank 1;"                 \
 120         "era ff800000 ff83ffff;"                \
 121         "cp.b ${loadaddr} ff800000 ${filesize};"\
 122         "save\0"                                \
 123         ""
 124
 125 #define CONFIG_PRAM             512     /* 512 KB */
 126 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 127
 128 #ifdef CONFIG_CMD_KGDB
 129 #       define CONFIG_SYS_CBSIZE        1024    /* Console I/O Buffer Size */
 130 #else
 131 #       define CONFIG_SYS_CBSIZE        256     /* Console I/O Buffer Size */
 132 #endif
 133
 134 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)        /* Print Buffer Size */
 135 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 136 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 137 #define CONFIG_SYS_LOAD_ADDR            0x00010000
 138
 139 #define CONFIG_SYS_CLK                  CONFIG_SYS_BUSCLK
 140 #define CONFIG_SYS_CPU_CLK              CONFIG_SYS_CLK * 2
 141
 142 #define CONFIG_SYS_MBAR         0xF0000000
 143 #define CONFIG_SYS_INTSRAM              (CONFIG_SYS_MBAR + 0x10000)
 144 #define CONFIG_SYS_INTSRAMSZ            0x8000
 145
 146 /*#define CONFIG_SYS_LATCH_ADDR         (CONFIG_SYS_CS1_BASE + 0x80000)*/
 147
 148 /*
 149  * Low Level Configuration Settings
 150  * (address mappings, register initial values, etc.)
 151  * You should know what you are doing if you make changes here.
 152  */
 153 /*-----------------------------------------------------------------------
 154  * Definitions for initial stack pointer and data area (in DPRAM)
 155  */
 156 #define CONFIG_SYS_INIT_RAM_ADDR        0xF2000000
 157 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in internal SRAM */
 158 #define CONFIG_SYS_INIT_RAM_CTRL        0x21
 159 #define CONFIG_SYS_INIT_RAM1_ADDR       (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
 160 #define CONFIG_SYS_INIT_RAM1_END        0x1000  /* End of used area in internal SRAM */
 161 #define CONFIG_SYS_INIT_RAM1_CTRL       0x21
 162 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
 163 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 164
 165 /*-----------------------------------------------------------------------
 166  * Start addresses for the final memory configuration
 167  * (Set up by the startup code)
 168  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 169  */
 170 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 171 #define CONFIG_SYS_SDRAM_CFG1           0x73711630
 172 #define CONFIG_SYS_SDRAM_CFG2           0x46770000
 173 #define CONFIG_SYS_SDRAM_CTRL           0xE10B0000
 174 #define CONFIG_SYS_SDRAM_EMOD           0x40010000
 175 #define CONFIG_SYS_SDRAM_MODE           0x018D0000
 176 #define CONFIG_SYS_SDRAM_DRVSTRENGTH    0x000002AA
 177 #ifdef CONFIG_SYS_DRAMSZ1
 178 #       define CONFIG_SYS_SDRAM_SIZE    (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1)
 179 #else
 180 #       define CONFIG_SYS_SDRAM_SIZE    CONFIG_SYS_DRAMSZ
 181 #endif
 182
 183 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE + 0x400
 184 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 185
 186 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 187 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor */
 188
 189 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 190
 191 /* Reserve 256 kB for malloc() */
 192 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 193 /*
 194  * For booting Linux, the board info and command line data
 195  * have to be in the first 8 MB of memory, since this is
 196  * the maximum mapped by the Linux kernel during initialization ??
 197  */
 198 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 199
 200 /*-----------------------------------------------------------------------
 201  * FLASH organization
 202  */
 203 #define CONFIG_SYS_FLASH_CFI
 204 #ifdef CONFIG_SYS_FLASH_CFI
 205 #       define CONFIG_SYS_FLASH_BASE            (CONFIG_SYS_CS0_BASE)
 206 #       define CONFIG_FLASH_CFI_DRIVER  1
 207 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 208 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 209 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 210 #       define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 211 #ifdef CONFIG_SYS_NOR1SZ
 212 #       define CONFIG_SYS_MAX_FLASH_BANKS       2       /* max number of memory banks */
 213 #       define CONFIG_SYS_FLASH_SIZE            ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20)
 214 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
 215 #else
 216 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 217 #       define CONFIG_SYS_FLASH_SIZE            (CONFIG_SYS_BOOTSZ << 20)
 218 #endif
 219 #endif
 220
 221 /* Configuration for environment
 222  * Environment is not embedded in u-boot. First time runing may have env
 223  * crc error warning if there is no correct environment on the flash.
 224  */
 225 #define CONFIG_ENV_OFFSET               0x40000
 226 #define CONFIG_ENV_SECT_SIZE    0x10000
 227 #define CONFIG_ENV_IS_IN_FLASH  1
 228
 229 /*-----------------------------------------------------------------------
 230  * Cache Configuration
 231  */
 232 #define CONFIG_SYS_CACHELINE_SIZE       16
 233
 234 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 235                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 236 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 237                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 238 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA + \
 239                                          CF_CACR_IDCM)
 240 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 241 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 242                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 243                                          CF_ACR_EN | CF_ACR_SM_ALL)
 244 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_BCINVA | \
 245                                          CF_CACR_IEC | CF_CACR_ICINVA)
 246 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 247                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 248                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 249
 250 /*-----------------------------------------------------------------------
 251  * Chipselect bank definitions
 252  */
 253 /*
 254  * CS0 - NOR Flash 1, 2, 4, or 8MB
 255  * CS1 - NOR Flash
 256  * CS2 - Available
 257  * CS3 - Available
 258  * CS4 - Available
 259  * CS5 - Available
 260  */
 261 #define CONFIG_SYS_CS0_BASE             0xFF800000
 262 #define CONFIG_SYS_CS0_MASK             (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001)
 263 #define CONFIG_SYS_CS0_CTRL             0x00101980
 264
 265 #ifdef CONFIG_SYS_NOR1SZ
 266 #define CONFIG_SYS_CS1_BASE             0xE0000000
 267 #define CONFIG_SYS_CS1_MASK             (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001)
 268 #define CONFIG_SYS_CS1_CTRL             0x00101D80
 269 #endif
 270
 271 #endif                          /* _M5485EVB_H */