include/configs/MPC8308RDB.h

   1 /*
   2  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
   3  * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #define CONFIG_DISPLAY_BOARDINFO
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_E300             1 /* E300 family */
  18 #define CONFIG_MPC830x          1 /* MPC830x family */
  19 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  20 #define CONFIG_MPC8308RDB       1 /* MPC8308RDB board specific */
  21
  22 #define CONFIG_SYS_TEXT_BASE    0xFE000000
  23
  24 #define CONFIG_MISC_INIT_R
  25
  26 /* new uImage format support */
  27 #define CONFIG_FIT                      1
  28 #define CONFIG_FIT_VERBOSE              1
  29
  30 #define CONFIG_MMC     1
  31
  32 #ifdef CONFIG_MMC
  33 #define CONFIG_FSL_ESDHC
  34 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  35 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
  36 #define CONFIG_SYS_FSL_ESDHC_USE_PIO
  37
  38 #define CONFIG_CMD_MMC
  39 #define CONFIG_GENERIC_MMC
  40 #define CONFIG_CMD_FAT
  41 #define CONFIG_DOS_PARTITION
  42 #endif
  43
  44 /*
  45  * On-board devices
  46  *
  47  * TSEC1 is SoC TSEC
  48  * TSEC2 is VSC switch
  49  */
  50 #define CONFIG_TSEC1
  51 #define CONFIG_VSC7385_ENET
  52
  53 /*
  54  * System Clock Setup
  55  */
  56 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  57 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  58
  59 /*
  60  * Hardware Reset Configuration Word
  61  * if CLKIN is 66.66MHz, then
  62  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  63  * We choose the A type silicon as default, so the core is 400Mhz.
  64  */
  65 #define CONFIG_SYS_HRCW_LOW (\
  66         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  67         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  68         HRCWL_SVCOD_DIV_2 |\
  69         HRCWL_CSB_TO_CLKIN_4X1 |\
  70         HRCWL_CORE_TO_CSB_3X1)
  71 /*
  72  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  73  * in 8308's HRCWH according to the manual, but original Freescale's
  74  * code has them and I've expirienced some problems using the board
  75  * with BDI3000 attached when I've tried to set these bits to zero
  76  * (UART doesn't work after the 'reset run' command).
  77  */
  78 #define CONFIG_SYS_HRCW_HIGH (\
  79         HRCWH_PCI_HOST |\
  80         HRCWH_PCI1_ARBITER_ENABLE |\
  81         HRCWH_CORE_ENABLE |\
  82         HRCWH_FROM_0X00000100 |\
  83         HRCWH_BOOTSEQ_DISABLE |\
  84         HRCWH_SW_WATCHDOG_DISABLE |\
  85         HRCWH_ROM_LOC_LOCAL_16BIT |\
  86         HRCWH_RL_EXT_LEGACY |\
  87         HRCWH_TSEC1M_IN_RGMII |\
  88         HRCWH_TSEC2M_IN_RGMII |\
  89         HRCWH_BIG_ENDIAN)
  90
  91 /*
  92  * System IO Config
  93  */
  94 #define CONFIG_SYS_SICRH (\
  95         SICRH_ESDHC_A_SD |\
  96         SICRH_ESDHC_B_SD |\
  97         SICRH_ESDHC_C_SD |\
  98         SICRH_GPIO_A_TSEC2 |\
  99         SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
 100         SICRH_IEEE1588_A_GPIO |\
 101         SICRH_USB |\
 102         SICRH_GTM_GPIO |\
 103         SICRH_IEEE1588_B_GPIO |\
 104         SICRH_ETSEC2_CRS |\
 105         SICRH_GPIOSEL_1 |\
 106         SICRH_TMROBI_V3P3 |\
 107         SICRH_TSOBI1_V2P5 |\
 108         SICRH_TSOBI2_V2P5)      /* 0x01b7d103 */
 109 #define CONFIG_SYS_SICRL (\
 110         SICRL_SPI_PF0 |\
 111         SICRL_UART_PF0 |\
 112         SICRL_IRQ_PF0 |\
 113         SICRL_I2C2_PF0 |\
 114         SICRL_ETSEC1_GTX_CLK125)        /* 0x00000040 */
 115
 116 /*
 117  * IMMR new address
 118  */
 119 #define CONFIG_SYS_IMMR         0xE0000000
 120
 121 /*
 122  * SERDES
 123  */
 124 #define CONFIG_FSL_SERDES
 125 #define CONFIG_FSL_SERDES1      0xe3000
 126
 127 /*
 128  * Arbiter Setup
 129  */
 130 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 131 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 132 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 133
 134 /*
 135  * DDR Setup
 136  */
 137 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 138 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 139 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 140 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 141 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 142                                 | DDRCDR_PZ_LOZ \
 143                                 | DDRCDR_NZ_LOZ \
 144                                 | DDRCDR_ODT \
 145                                 | DDRCDR_Q_DRN)
 146                                 /* 0x7b880001 */
 147 /*
 148  * Manually set up DDR parameters
 149  * consist of two chips HY5PS12621BFP-C4 from HYNIX
 150  */
 151
 152 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 153
 154 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 155 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 156                                 | CSCONFIG_ODT_RD_NEVER \
 157                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 158                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 159                                 /* 0x80010102 */
 160 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 161 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 162                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 163                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 164                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 165                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 166                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 167                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 168                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 169                                 /* 0x00220802 */
 170 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 171                                 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 172                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 173                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
 174                                 | (6 << TIMING_CFG1_REFREC_SHIFT) \
 175                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 176                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 177                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 178                                 /* 0x27256222 */
 179 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
 180                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 181                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 182                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 183                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 184                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 185                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 186                                 /* 0x121048c5 */
 187 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
 188                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 189                                 /* 0x03600100 */
 190 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 191                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 192                                 | SDRAM_CFG_DBW_32)
 193                                 /* 0x43080000 */
 194
 195 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 196 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 197                                 | (0x0232 << SDRAM_MODE_SD_SHIFT))
 198                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
 199 #define CONFIG_SYS_DDR_MODE2            0x00000000
 200
 201 /*
 202  * Memory test
 203  */
 204 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 205 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 206
 207 /*
 208  * The reserved memory
 209  */
 210 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 211
 212 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 213 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 214
 215 /*
 216  * Initial RAM Base Address Setup
 217  */
 218 #define CONFIG_SYS_INIT_RAM_LOCK        1
 219 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 220 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 221 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 222         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 223
 224 /*
 225  * Local Bus Configuration & Clock Setup
 226  */
 227 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 228 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 229 #define CONFIG_SYS_LBC_LBCR             0x00040000
 230
 231 /*
 232  * FLASH on the Local Bus
 233  */
 234 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 235 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 236 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 237
 238 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 239 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is 8M */
 240 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 241
 242 /* Window base at flash base */
 243 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 244 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 245
 246 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 247                                 | BR_PS_16      /* 16 bit port */ \
 248                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 249                                 | BR_V)         /* valid */
 250 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 251                                 | OR_UPM_XAM \
 252                                 | OR_GPCM_CSNT \
 253                                 | OR_GPCM_ACS_DIV2 \
 254                                 | OR_GPCM_XACS \
 255                                 | OR_GPCM_SCY_15 \
 256                                 | OR_GPCM_TRLX_SET \
 257                                 | OR_GPCM_EHTR_SET)
 258
 259 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 260 /* 127 64KB sectors and 8 8KB top sectors per device */
 261 #define CONFIG_SYS_MAX_FLASH_SECT       135
 262
 263 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 264 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 265
 266 /*
 267  * NAND Flash on the Local Bus
 268  */
 269 #define CONFIG_SYS_NAND_BASE    0xE0600000              /* 0xE0600000 */
 270 #define CONFIG_SYS_NAND_WINDOW_SIZE     (32 * 1024)     /* 0x00008000 */
 271 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_NAND_BASE \
 272                                 | BR_DECC_CHK_GEN       /* Use HW ECC */ \
 273                                 | BR_PS_8               /* 8 bit Port */ \
 274                                 | BR_MS_FCM             /* MSEL = FCM */ \
 275                                 | BR_V)                 /* valid */
 276 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
 277                                 | OR_FCM_CSCT \
 278                                 | OR_FCM_CST \
 279                                 | OR_FCM_CHT \
 280                                 | OR_FCM_SCY_1 \
 281                                 | OR_FCM_TRLX \
 282                                 | OR_FCM_EHTR)
 283                                 /* 0xFFFF8396 */
 284
 285 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
 286 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)
 287
 288 #ifdef CONFIG_VSC7385_ENET
 289 #define CONFIG_TSEC2
 290                                         /* VSC7385 Base address on CS2 */
 291 #define CONFIG_SYS_VSC7385_BASE         0xF0000000
 292 #define CONFIG_SYS_VSC7385_SIZE         (128 * 1024) /* 0x00020000 */
 293 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_VSC7385_BASE \
 294                                         | BR_PS_8       /* 8-bit port */ \
 295                                         | BR_MS_GPCM    /* MSEL = GPCM */ \
 296                                         | BR_V)         /* valid */
 297                                         /* 0xF0000801 */
 298 #define CONFIG_SYS_OR2_PRELIM           (P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
 299                                         | OR_GPCM_CSNT \
 300                                         | OR_GPCM_XACS \
 301                                         | OR_GPCM_SCY_15 \
 302                                         | OR_GPCM_SETA \
 303                                         | OR_GPCM_TRLX_SET \
 304                                         | OR_GPCM_EHTR_SET)
 305                                         /* 0xFFFE09FF */
 306 /* Access window base at VSC7385 base */
 307 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VSC7385_BASE
 308 /* Access window size 128K */
 309 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_128KB)
 310 /* The flash address and size of the VSC7385 firmware image */
 311 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
 312 #define CONFIG_VSC7385_IMAGE_SIZE       8192
 313 #endif
 314 /*
 315  * Serial Port
 316  */
 317 #define CONFIG_CONS_INDEX       1
 318 #define CONFIG_SYS_NS16550_SERIAL
 319 #define CONFIG_SYS_NS16550_REG_SIZE     1
 320 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 321
 322 #define CONFIG_SYS_BAUDRATE_TABLE  \
 323         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 324
 325 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 326 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 327
 328 /* Use the HUSH parser */
 329 #define CONFIG_SYS_HUSH_PARSER
 330
 331 /* Pass open firmware flat tree */
 332 #define CONFIG_OF_LIBFDT        1
 333 #define CONFIG_OF_BOARD_SETUP   1
 334 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 335
 336 /* I2C */
 337 #define CONFIG_SYS_I2C
 338 #define CONFIG_SYS_I2C_FSL
 339 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 340 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 341 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 342 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 343 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 344 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 345 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 346
 347 /*
 348  * SPI on header J8
 349  *
 350  * WARNING: enabling this will break TSEC2 (connected to the Vitesse switch)
 351  * due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
 352  */
 353 #ifdef CONFIG_MPC8XXX_SPI
 354 #define CONFIG_CMD_SPI
 355 #define CONFIG_USE_SPIFLASH
 356 #define CONFIG_SPI_FLASH_SPANSION
 357 #define CONFIG_CMD_SF
 358 #endif
 359
 360 /*
 361  * Board info - revision and where boot from
 362  */
 363 #define CONFIG_SYS_I2C_PCF8574A_ADDR    0x39
 364
 365 /*
 366  * Config on-board RTC
 367  */
 368 #define CONFIG_RTC_DS1337       /* ds1339 on board, use ds1337 rtc via i2c */
 369 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 370
 371 /*
 372  * General PCI
 373  * Addresses are mapped 1-1.
 374  */
 375 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 376 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 377 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 378 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 379 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 380 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 381 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 382 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 383 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 384
 385 /* enable PCIE clock */
 386 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 387
 388 #define CONFIG_PCI
 389 #define CONFIG_PCI_INDIRECT_BRIDGE
 390 #define CONFIG_PCIE
 391
 392 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 393
 394 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 395 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 396
 397 /*
 398  * TSEC
 399  */
 400 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 401 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 402 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 403 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 404 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 405
 406 /*
 407  * TSEC ethernet configuration
 408  */
 409 #define CONFIG_MII              1 /* MII PHY management */
 410 #define CONFIG_TSEC1_NAME       "eTSEC0"
 411 #define CONFIG_TSEC2_NAME       "eTSEC1"
 412 #define TSEC1_PHY_ADDR          2
 413 #define TSEC2_PHY_ADDR          1
 414 #define TSEC1_PHYIDX            0
 415 #define TSEC2_PHYIDX            0
 416 #define TSEC1_FLAGS             TSEC_GIGABIT
 417 #define TSEC2_FLAGS             TSEC_GIGABIT
 418
 419 /* Options are: eTSEC[0-1] */
 420 #define CONFIG_ETHPRIME         "eTSEC0"
 421
 422 /*
 423  * Environment
 424  */
 425 #define CONFIG_ENV_IS_IN_FLASH  1
 426 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 427                                  CONFIG_SYS_MONITOR_LEN)
 428 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 429 #define CONFIG_ENV_SIZE         0x2000
 430 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 431 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 432
 433 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 434 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 435
 436 /*
 437  * BOOTP options
 438  */
 439 #define CONFIG_BOOTP_BOOTFILESIZE
 440 #define CONFIG_BOOTP_BOOTPATH
 441 #define CONFIG_BOOTP_GATEWAY
 442 #define CONFIG_BOOTP_HOSTNAME
 443
 444 /*
 445  * Command line configuration.
 446  */
 447 #define CONFIG_CMD_DATE
 448 #define CONFIG_CMD_DHCP
 449 #define CONFIG_CMD_I2C
 450 #define CONFIG_CMD_MII
 451 #define CONFIG_CMD_PCI
 452 #define CONFIG_CMD_PING
 453
 454 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 455
 456 /*
 457  * Miscellaneous configurable options
 458  */
 459 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 460 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 461
 462 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 463
 464 /* Print Buffer Size */
 465 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 466 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 467 /* Boot Argument Buffer Size */
 468 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 469
 470 /*
 471  * For booting Linux, the board info and command line data
 472  * have to be in the first 256 MB of memory, since this is
 473  * the maximum mapped by the Linux kernel during initialization.
 474  */
 475 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 476
 477 /*
 478  * Core HID Setup
 479  */
 480 #define CONFIG_SYS_HID0_INIT    0x000000000
 481 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 482                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 483                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 484 #define CONFIG_SYS_HID2         HID2_HBE
 485
 486 /*
 487  * MMU Setup
 488  */
 489
 490 /* DDR: cache cacheable */
 491 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 492                                         BATL_MEMCOHERENCE)
 493 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 494                                         BATU_VS | BATU_VP)
 495 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 496 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 497
 498 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
 499 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 500                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 501 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 502                                         BATU_VP)
 503 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 504 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 505
 506 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 507 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 508                                         BATL_MEMCOHERENCE)
 509 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 510                                         BATU_VS | BATU_VP)
 511 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 512                                         BATL_CACHEINHIBIT | \
 513                                         BATL_GUARDEDSTORAGE)
 514 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 515
 516 /* Stack in dcache: cacheable, no memory coherence */
 517 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 518 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 519                                         BATU_VS | BATU_VP)
 520 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 521 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 522
 523 /*
 524  * Environment Configuration
 525  */
 526
 527 #define CONFIG_ENV_OVERWRITE
 528
 529 #if defined(CONFIG_TSEC_ENET)
 530 #define CONFIG_HAS_ETH0
 531 #define CONFIG_HAS_ETH1
 532 #endif
 533
 534 #define CONFIG_BAUDRATE 115200
 535
 536 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 537
 538 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
 539
 540 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 541         "netdev=eth0\0"                                                 \
 542         "consoledev=ttyS0\0"                                            \
 543         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 544                 "nfsroot=${serverip}:${rootpath}\0"                     \
 545         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 546         "addip=setenv bootargs ${bootargs} "                            \
 547                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 548                 ":${hostname}:${netdev}:off panic=1\0"                  \
 549         "addtty=setenv bootargs ${bootargs}"                            \
 550                 " console=${consoledev},${baudrate}\0"                  \
 551         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 552         "addmisc=setenv bootargs ${bootargs}\0"                         \
 553         "kernel_addr=FE080000\0"                                        \
 554         "fdt_addr=FE280000\0"                                           \
 555         "ramdisk_addr=FE290000\0"                                       \
 556         "u-boot=mpc8308rdb/u-boot.bin\0"                                \
 557         "kernel_addr_r=1000000\0"                                       \
 558         "fdt_addr_r=C00000\0"                                           \
 559         "hostname=mpc8308rdb\0"                                         \
 560         "bootfile=mpc8308rdb/uImage\0"                                  \
 561         "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0"                           \
 562         "rootpath=/opt/eldk-4.2/ppc_6xx\0"                              \
 563         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 564                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 565         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 566                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 567         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 568                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 569                 "run nfsargs addip addtty addmtd addmisc;"              \
 570                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 571         "bootcmd=run flash_self\0"                                      \
 572         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 573         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 574                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 575                 " +${filesize};cp.b ${fileaddr} "                       \
 576                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 577         "upd=run load update\0"                                         \
 578
 579 #endif  /* __CONFIG_H */