include/configs/MPC8540ADS.h

   1 /*
   2  * Copyright 2004, 2011 Freescale Semiconductor.
   3  * (C) Copyright 2002,2003 Motorola,Inc.
   4  * Xianghua Xiao <X.Xiao@motorola.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * mpc8540ads board configuration file
  11  *
  12  * Please refer to doc/README.mpc85xx for more info.
  13  *
  14  * Make sure you change the MAC address and other network params first,
  15  * search for CONFIG_SERVERIP, etc in this file.
  16  */
  17
  18 #ifndef __CONFIG_H
  19 #define __CONFIG_H
  20
  21 /* High Level Configuration Options */
  22 #define CONFIG_BOOKE            1       /* BOOKE */
  23 #define CONFIG_E500             1       /* BOOKE e500 family */
  24 #define CONFIG_MPC8540          1       /* MPC8540 specific */
  25 #define CONFIG_MPC8540ADS       1       /* MPC8540ADS board specific */
  26
  27 /*
  28  * default CCARBAR is at 0xff700000
  29  * assume U-Boot is less than 0.5MB
  30  */
  31 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  32
  33 #ifndef CONFIG_HAS_FEC
  34 #define CONFIG_HAS_FEC          1       /* 8540 has FEC */
  35 #endif
  36
  37 #define CONFIG_PCI
  38 #define CONFIG_PCI_INDIRECT_BRIDGE
  39 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  40 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
  41 #define CONFIG_ENV_OVERWRITE
  42 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  43
  44 /*
  45  * sysclk for MPC85xx
  46  *
  47  * Two valid values are:
  48  *    33000000
  49  *    66000000
  50  *
  51  * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
  52  * is likely the desired value here, so that is now the default.
  53  * The board, however, can run at 66MHz.  In any event, this value
  54  * must match the settings of some switches.  Details can be found
  55  * in the README.mpc85xxads.
  56  *
  57  * XXX -- Can't we run at 66 MHz, anyway?  PCI should drop to
  58  * 33MHz to accommodate, based on a PCI pin.
  59  * Note that PCI-X won't work at 33MHz.
  60  */
  61
  62 #ifndef CONFIG_SYS_CLK_FREQ
  63 #define CONFIG_SYS_CLK_FREQ     33000000
  64 #endif
  65
  66
  67 /*
  68  * These can be toggled for performance analysis, otherwise use default.
  69  */
  70 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  71 #define CONFIG_BTB                      /* toggle branch predition */
  72
  73 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  74 #define CONFIG_SYS_MEMTEST_END          0x00400000
  75
  76 #define CONFIG_SYS_CCSRBAR              0xe0000000
  77 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  78
  79 /* DDR Setup */
  80 #define CONFIG_SYS_FSL_DDR1
  81 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup*/
  82 #define CONFIG_DDR_SPD
  83 #undef CONFIG_FSL_DDR_INTERACTIVE
  84
  85 #define CONFIG_MEM_INIT_VALUE           0xDeadBeef
  86
  87 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  88 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  89
  90 #define CONFIG_NUM_DDR_CONTROLLERS      1
  91 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  92 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
  93
  94 /* I2C addresses of SPD EEPROMs */
  95 #define SPD_EEPROM_ADDRESS      0x51    /* CTLR 0 DIMM 0 */
  96
  97 /* These are used when DDR doesn't use SPD. */
  98 #define CONFIG_SYS_SDRAM_SIZE   128             /* DDR is 128MB */
  99 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007      /* 0-128MB */
 100 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80000002
 101 #define CONFIG_SYS_DDR_TIMING_1 0x37344321
 102 #define CONFIG_SYS_DDR_TIMING_2 0x00000800      /* P9-45,may need tuning */
 103 #define CONFIG_SYS_DDR_CONTROL          0xc2000000      /* unbuffered,no DYN_PWR */
 104 #define CONFIG_SYS_DDR_MODE             0x00000062      /* DLL,normal,seq,4/2.5 */
 105 #define CONFIG_SYS_DDR_INTERVAL 0x05200100      /* autocharge,no open page */
 106
 107 /*
 108  * SDRAM on the Local Bus
 109  */
 110 #define CONFIG_SYS_LBC_SDRAM_BASE       0xf0000000      /* Localbus SDRAM */
 111 #define CONFIG_SYS_LBC_SDRAM_SIZE       64              /* LBC SDRAM is 64MB */
 112
 113 #define CONFIG_SYS_FLASH_BASE           0xff000000      /* start of FLASH 16M */
 114 #define CONFIG_SYS_BR0_PRELIM           0xff001801      /* port size 32bit */
 115
 116 #define CONFIG_SYS_OR0_PRELIM           0xff006ff7      /* 16MB Flash */
 117 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 118 #define CONFIG_SYS_MAX_FLASH_SECT       64              /* sectors per device */
 119 #undef  CONFIG_SYS_FLASH_CHECKSUM
 120 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 121 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 122
 123 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 124
 125 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 126 #define CONFIG_SYS_RAMBOOT
 127 #else
 128 #undef  CONFIG_SYS_RAMBOOT
 129 #endif
 130
 131 #define CONFIG_FLASH_CFI_DRIVER
 132 #define CONFIG_SYS_FLASH_CFI
 133 #define CONFIG_SYS_FLASH_EMPTY_INFO
 134
 135 #undef CONFIG_CLOCKS_IN_MHZ
 136
 137
 138 /*
 139  * Local Bus Definitions
 140  */
 141
 142 /*
 143  * Base Register 2 and Option Register 2 configure SDRAM.
 144  * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
 145  *
 146  * For BR2, need:
 147  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 148  *    port-size = 32-bits = BR2[19:20] = 11
 149  *    no parity checking = BR2[21:22] = 00
 150  *    SDRAM for MSEL = BR2[24:26] = 011
 151  *    Valid = BR[31] = 1
 152  *
 153  * 0    4    8    12   16   20   24   28
 154  * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
 155  *
 156  * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
 157  * FIXME: the top 17 bits of BR2.
 158  */
 159
 160 #define CONFIG_SYS_BR2_PRELIM           0xf0001861
 161
 162 /*
 163  * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
 164  *
 165  * For OR2, need:
 166  *    64MB mask for AM, OR2[0:7] = 1111 1100
 167  *                 XAM, OR2[17:18] = 11
 168  *    9 columns OR2[19-21] = 010
 169  *    13 rows   OR2[23-25] = 100
 170  *    EAD set for extra time OR[31] = 1
 171  *
 172  * 0    4    8    12   16   20   24   28
 173  * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
 174  */
 175
 176 #define CONFIG_SYS_OR2_PRELIM           0xfc006901
 177
 178 #define CONFIG_SYS_LBC_LCRR             0x00030004    /* LB clock ratio reg */
 179 #define CONFIG_SYS_LBC_LBCR             0x00000000    /* LB config reg */
 180 #define CONFIG_SYS_LBC_LSRT             0x20000000    /* LB sdram refresh timer */
 181 #define CONFIG_SYS_LBC_MRTPR            0x20000000    /* LB refresh timer prescal*/
 182
 183 #define CONFIG_SYS_LBC_LSDMR_COMMON     ( LSDMR_BSMA1516        \
 184                                 | LSDMR_RFCR5           \
 185                                 | LSDMR_PRETOACT3       \
 186                                 | LSDMR_ACTTORW3        \
 187                                 | LSDMR_BL8             \
 188                                 | LSDMR_WRC2            \
 189                                 | LSDMR_CL3             \
 190                                 | LSDMR_RFEN            \
 191                                 )
 192
 193 /*
 194  * SDRAM Controller configuration sequence.
 195  */
 196 #define CONFIG_SYS_LBC_LSDMR_1  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
 197 #define CONFIG_SYS_LBC_LSDMR_2  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 198 #define CONFIG_SYS_LBC_LSDMR_3  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 199 #define CONFIG_SYS_LBC_LSDMR_4  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 200 #define CONFIG_SYS_LBC_LSDMR_5  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 201
 202
 203 /*
 204  * 32KB, 8-bit wide for ADS config reg
 205  */
 206 #define CONFIG_SYS_BR4_PRELIM          0xf8000801
 207 #define CONFIG_SYS_OR4_PRELIM           0xffffe1f1
 208 #define CONFIG_SYS_BCSR         (CONFIG_SYS_BR4_PRELIM & 0xffff8000)
 209
 210 #define CONFIG_SYS_INIT_RAM_LOCK        1
 211 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000      /* Initial RAM address */
 212 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */
 213
 214 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 215 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 216
 217 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB for Mon */
 218 #define CONFIG_SYS_MALLOC_LEN           (128 * 1024)    /* Reserved for malloc */
 219
 220 /* Serial Port */
 221 #define CONFIG_CONS_INDEX     1
 222 #define CONFIG_SYS_NS16550
 223 #define CONFIG_SYS_NS16550_SERIAL
 224 #define CONFIG_SYS_NS16550_REG_SIZE    1
 225 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 226
 227 #define CONFIG_SYS_BAUDRATE_TABLE  \
 228         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 229
 230 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 231 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 232
 233 /* Use the HUSH parser */
 234 #define CONFIG_SYS_HUSH_PARSER
 235 #ifdef  CONFIG_SYS_HUSH_PARSER
 236 #endif
 237
 238 /* pass open firmware flat tree */
 239 #define CONFIG_OF_LIBFDT                1
 240 #define CONFIG_OF_BOARD_SETUP           1
 241 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 242
 243 /*
 244  * I2C
 245  */
 246 #define CONFIG_SYS_I2C
 247 #define CONFIG_SYS_I2C_FSL
 248 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 249 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 250 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 251 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 252
 253 /* RapidIO MMU */
 254 #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000      /* base address */
 255 #define CONFIG_SYS_RIO_MEM_BUS  0xc0000000      /* base address */
 256 #define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000
 257 #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000      /* 128M */
 258
 259 /*
 260  * General PCI
 261  * Memory space is mapped 1-1, but I/O space must start from 0.
 262  */
 263 #define CONFIG_SYS_PCI1_MEM_VIRT        0x80000000
 264 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
 265 #define CONFIG_SYS_PCI1_MEM_PHYS        0x80000000
 266 #define CONFIG_SYS_PCI1_MEM_SIZE        0x20000000      /* 512M */
 267 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
 268 #define CONFIG_SYS_PCI1_IO_BUS  0x00000000
 269 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
 270 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000        /* 1M */
 271
 272 #if defined(CONFIG_PCI)
 273
 274 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 275
 276 #undef CONFIG_EEPRO100
 277 #undef CONFIG_TULIP
 278
 279 #if !defined(CONFIG_PCI_PNP)
 280     #define PCI_ENET0_IOADDR    0xe0000000
 281     #define PCI_ENET0_MEMADDR   0xe0000000
 282     #define PCI_IDSEL_NUMBER    0x0c    /* slot0->3(IDSEL)=12->15 */
 283 #endif
 284
 285 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 286 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 287
 288 #endif  /* CONFIG_PCI */
 289
 290
 291 #if defined(CONFIG_TSEC_ENET)
 292
 293 #define CONFIG_MII              1       /* MII PHY management */
 294 #define CONFIG_TSEC1    1
 295 #define CONFIG_TSEC1_NAME       "TSEC0"
 296 #define CONFIG_TSEC2    1
 297 #define CONFIG_TSEC2_NAME       "TSEC1"
 298 #define TSEC1_PHY_ADDR          0
 299 #define TSEC2_PHY_ADDR          1
 300 #define TSEC1_PHYIDX            0
 301 #define TSEC2_PHYIDX            0
 302 #define TSEC1_FLAGS             TSEC_GIGABIT
 303 #define TSEC2_FLAGS             TSEC_GIGABIT
 304
 305
 306 #if CONFIG_HAS_FEC
 307 #define CONFIG_MPC85XX_FEC      1
 308 #define CONFIG_MPC85XX_FEC_NAME         "FEC"
 309 #define FEC_PHY_ADDR            3
 310 #define FEC_PHYIDX              0
 311 #define FEC_FLAGS               0
 312 #endif
 313
 314 /* Options are: TSEC[0-1], FEC */
 315 #define CONFIG_ETHPRIME         "TSEC0"
 316
 317 #endif  /* CONFIG_TSEC_ENET */
 318
 319
 320 /*
 321  * Environment
 322  */
 323 #ifndef CONFIG_SYS_RAMBOOT
 324   #define CONFIG_ENV_IS_IN_FLASH        1
 325   #define CONFIG_ENV_ADDR               (CONFIG_SYS_MONITOR_BASE + 0x40000)
 326   #define CONFIG_ENV_SECT_SIZE  0x40000 /* 256K(one sector) for env */
 327   #define CONFIG_ENV_SIZE               0x2000
 328 #else
 329   #define CONFIG_SYS_NO_FLASH           1       /* Flash is not usable now */
 330   #define CONFIG_ENV_IS_NOWHERE 1       /* Store ENV in memory only */
 331   #define CONFIG_ENV_ADDR               (CONFIG_SYS_MONITOR_BASE - 0x1000)
 332   #define CONFIG_ENV_SIZE               0x2000
 333 #endif
 334
 335 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 336 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 337
 338
 339 /*
 340  * BOOTP options
 341  */
 342 #define CONFIG_BOOTP_BOOTFILESIZE
 343 #define CONFIG_BOOTP_BOOTPATH
 344 #define CONFIG_BOOTP_GATEWAY
 345 #define CONFIG_BOOTP_HOSTNAME
 346
 347
 348 /*
 349  * Command line configuration.
 350  */
 351 #define CONFIG_CMD_PING
 352 #define CONFIG_CMD_I2C
 353 #define CONFIG_CMD_ELF
 354 #define CONFIG_CMD_IRQ
 355
 356 #if defined(CONFIG_PCI)
 357     #define CONFIG_CMD_PCI
 358 #endif
 359
 360 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 361
 362 /*
 363  * Miscellaneous configurable options
 364  */
 365 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 366 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 367 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 368 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 369
 370 #if defined(CONFIG_CMD_KGDB)
 371     #define CONFIG_SYS_CBSIZE   1024            /* Console I/O Buffer Size */
 372 #else
 373     #define CONFIG_SYS_CBSIZE   256             /* Console I/O Buffer Size */
 374 #endif
 375
 376 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 377 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 378 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 379
 380 /*
 381  * For booting Linux, the board info and command line data
 382  * have to be in the first 64 MB of memory, since this is
 383  * the maximum mapped by the Linux kernel during initialization.
 384  */
 385 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory map for Linux*/
 386 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 387
 388 #if defined(CONFIG_CMD_KGDB)
 389 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 390 #endif
 391
 392
 393 /*
 394  * Environment Configuration
 395  */
 396
 397 /* The mac addresses for all ethernet interface */
 398 #if defined(CONFIG_TSEC_ENET)
 399 #define CONFIG_HAS_ETH0
 400 #define CONFIG_HAS_ETH1
 401 #define CONFIG_HAS_ETH2
 402 #endif
 403
 404 #define CONFIG_IPADDR    192.168.1.253
 405
 406 #define CONFIG_HOSTNAME         unknown
 407 #define CONFIG_ROOTPATH         "/nfsroot"
 408 #define CONFIG_BOOTFILE         "your.uImage"
 409
 410 #define CONFIG_SERVERIP  192.168.1.1
 411 #define CONFIG_GATEWAYIP 192.168.1.1
 412 #define CONFIG_NETMASK   255.255.255.0
 413
 414 #define CONFIG_LOADADDR  200000 /* default location for tftp and bootm */
 415
 416 #define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
 417 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 418
 419 #define CONFIG_BAUDRATE 115200
 420
 421 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 422    "netdev=eth0\0"                                                      \
 423    "consoledev=ttyS0\0"                                                 \
 424    "ramdiskaddr=1000000\0"                                              \
 425    "ramdiskfile=your.ramdisk.u-boot\0"                                  \
 426    "fdtaddr=400000\0"                                                   \
 427    "fdtfile=your.fdt.dtb\0"
 428
 429 #define CONFIG_NFSBOOTCOMMAND                                           \
 430    "setenv bootargs root=/dev/nfs rw "                                  \
 431       "nfsroot=$serverip:$rootpath "                                    \
 432       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 433       "console=$consoledev,$baudrate $othbootargs;"                     \
 434    "tftp $loadaddr $bootfile;"                                          \
 435    "tftp $fdtaddr $fdtfile;"                                            \
 436    "bootm $loadaddr - $fdtaddr"
 437
 438 #define CONFIG_RAMBOOTCOMMAND \
 439    "setenv bootargs root=/dev/ram rw "                                  \
 440       "console=$consoledev,$baudrate $othbootargs;"                     \
 441    "tftp $ramdiskaddr $ramdiskfile;"                                    \
 442    "tftp $loadaddr $bootfile;"                                          \
 443    "tftp $fdtaddr $fdtfile;"                                            \
 444    "bootm $loadaddr $ramdiskaddr $fdtaddr"
 445
 446 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 447
 448 #endif  /* __CONFIG_H */